Hello!
I have problem, i want to flash Android 7.0 with odin on my Sasmung Galaxy S7 (SM-G930F), but i get FAIL everytime, i tryed many ways but always FAIL. I used BL, AP, CP and CSC file.
On my phone when it is in download mode (after flashing) it is written SV REV. CHECK FAIL (BOOTLOADER) DEVICE: 3, BINARY: 2, or other device or binary error.
I cant even use emergency recovery smartswitch, because it seems that my phone is not supported.
Please, i need help there.
I get this log in odin:
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 24 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 4466 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
alescresnar24 said:
Hello!
I have problem, i want to flash Android 7.0 with odin on my Sasmung Galaxy S7 (SM-G930F),.........
Click to expand...
Click to collapse
I don't have this device but, your best bet is to post this question within one of the following threads that's specific to your device and variants.
https://forum.xda-developers.com/showthread.php?t=3702963
https://forum.xda-developers.com/showthread.php?t=3341138
Good Luck!
~~~~~~~~~~~~~~~
UNLESS asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my SM-G900T device.
Related
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Sliderse said:
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Click to expand...
Click to collapse
Have you tried flashing stock rom of the Chinese version of the Note GT-19220?
Since you have the chine i9220 then make sure you get the specific roms for the chinese version. If you try flashing the N7000 roms you may get this error or may brick it so just be careful.
Sliderse said:
Hi All,
I have a Chinese version of the Note GT-19220, It has ICS on it but is missing Google Play so have tried to flash a new western version of ICS using Odin PC
I have followed the instructions exactly as described and I get a fail almost at the end of the process.
Now I get a picture of a phone and a yellow triangle and a monitor and below it is says Software Update failed.
The message I see in Odin is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLQ3_N7000XXLPT_N7000NEELP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> cache.img
<ID:0/006> NAND Write Start!!
<ID:0/006> factoryfs.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how I can fix this? I have tried with several roms with the same result.
Do I need to take it to Samsung now to be fixed?
Click to expand...
Click to collapse
You flashed N7000XXLQ3_N7000XXLPT_N7000NEELP4
It was N7000's rom and i feel its not compatible for i9220
You can flashed lidroid rom, both i9220 and n7000 can be flashed, I tried it and it works
Sent from my GT-N7000 using xda premium
OK here we go, I'm no idiot, I've been flashing phones etc for a good couple of years, consider myself excellent as a computer user, was a repair technician.
With that out the way;
I downloaded a 4.2 BETA for my Galaxy s3 mini, used Odin to try and flash it and received "<ID:0/008> Complete(Write) operation failed." first time, no other errors.
Phone has usb debugging enabled.
Do I tried again, same thing. Then tried once more, and received;
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
Now as far as I know, one should only get this error when a re-partition has gone wrong. I did NOT check the re-partition option.
So having a read around, I saw someone had posted a .pit file for my phone, so went to use this, and now this is my error;
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Complete(Write) operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Could anyone help at all?
MY log, as far back as it shows;
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008>
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008>
<ID:0/008> Re-Partition operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Complete(Write) operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007>
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Complete(Write) operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008>
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUFME7_I9300OXAFME7_I9300XXUFME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Complete(Write) operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Oh and trying to start the phone normally, mostly just hangs at the Samsung logo, though when trying a hard reset, it would hang at a spinning "wheel", which in itself was stuck.
Many thanks
OK, update, flashed stock FW back, worked fine, now phone is just stuck at the Samsung logo. Can't get into recovery. The hell is going on?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8190NXXAMB1_I8190NEVRAMB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.img
<ID:0/009> NAND Write Start!!
<ID:0/009> modem.bin
<ID:0/009> STE_boot1.img
<ID:0/009> STE_boot2.img
<ID:0/009> system.img
<ID:0/009> cache.img
<ID:0/009> hidden.img
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/009> Removed!!
hevydani said:
OK, update, flashed stock FW back, worked fine, now phone is just stuck at the Samsung logo. The hell is going on?
Click to expand...
Click to collapse
Boot into stock recovery and wipe data, note that you will lose all your files (are your files on internal storage or extsdcard, if the latter you should be safe.
Sent from my SGH-I747 using Tapatalk 2
rani9990 said:
Boot into stock recovery and wipe data, note that you will lose all your files (are your files on internal storage or extsdcard, if the latter you should be safe.
Sent from my SGH-I747 using Tapatalk 2
Click to expand...
Click to collapse
I can't even get into recovery mode.
Thanks for the reply
hevydani said:
I can't even get into recovery mode.
Thanks for the reply
Click to expand...
Click to collapse
Try this PARAM or I8190N PIT file I presume you're phone is NFC version. Find them here:
http://forum.xda-developers.com/showthread.php?t=2159660 use the PARAM as PDA in Odin first.
Sent from my GT-I8190 using Tapatalk 2
kicker63 said:
Try this PARAM or I8190N PIT file I presume you're phone is NFC version. Find them here:
http://forum.xda-developers.com/showthread.php?t=2159660 use the PARAM as PDA in Odin first.
Sent from my GT-I8190 using Tapatalk 2
Click to expand...
Click to collapse
Jesus christ you just saved my ass!
I literally love you, thanks so much.
I'm stuck decided to try the latest UK Version of Tizen OS loaded it in Odin 3.09 into the AP Slot pressed start and the damn Odin decided to pop up with a error and close out in Windows, now if I try anything still download mode and reopened Odin 3.07 or 3.09, but it never fully installs I'm in the emergency download kies recovery screen.
Is it possible to install a Odin'ed firmware from here, from what I've learned of the screen/area of recovery, it's the same thing as download mode. I tried the latest Tizen OS again and all it did was sit forever at zImage area of flashing.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCOA2_V700OXACOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
Or I get this:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCOA2_V700OXACOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/016> Removed!!
<ID:0/016> Added!!
<ID:0/016> Removed!!
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/016> Removed!!
<ID:0/016> Added!!
<ID:0/016> Removed!!
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> sboot.bin
<ID:0/016> NAND Write Start!!
<ID:0/016> zImage
It just sits there at BOOTLOADER, have to go about getting this far by disconnecting the watch and holding in the power button till it reboots and turns back on to the same screen. Then plug it back up again and press start again in Odin.
I tried on two PC's and this as far as it gets or what all it does.
What can I do to fix this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Don't care if I have to flash JB or TZ, just as long as it's back up and running.
Fixed it had to flash Android MK7 first, now to trying Odin'ing Tizen again
Anddddd zImage gets stuck again... Grrrr
Hi!
I have the same problem... I comes from Null 23 and I want install Tizen
You find the solution for this problem?
Try to flash the tizen NE9 first
> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i dont know what to do,
i have sprint and downloaded the stock firmware but keep getting the auth errror
i also got a kernel panic error then it went to a unknown error
seekerofwits said:
> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i dont know what to do,
i have sprint and downloaded the stock firmware but keep getting the auth errror
i also got a kernel panic error then it went to a unknown error
Click to expand...
Click to collapse
if u want root, just do the steps 1 and 2, and then redo the steps again without the nand erase the 2nd time on part 1, also on the step 2 the 2nd time use the csc from ur firmware... make sure u r on the correct version for root of ur Bootloader files.. v1 or v2 and now v3..
if u don't want root anymore... follow this I just did for someone... https://forum.xda-developers.com/showpost.php?p=75628989&postcount=4143 in the root thread...
most important is to use usb2 controller not the usb 3 or 3.1.. that is where I always had issues.
if at any time it stops with an error.. restart ur phone and go back into download mode again, and I restart odin...
Regular Odin for returning to stock, prince comey odin for rooting..
buy Exynos, all Android phones MUST have unlocked bootloader !!
Also having problems returning to stock
I need serious help.
This is not my first root on a Samsung phone. I've been rooting & custom O.S.-ing since my Galaxy SIII. Up until recently, I've been very happy with my rooted/custom Note 4, but it's
This Note 8 (Unlocked~SM-N950U) is the worst phone I've had in years. I achieved root with the SamFail method (W00T!), but I've discovered that I absolutely LOATHE the Newer Samsung U/I (or "Samsung Experience", as they've labeled it) and I've bought an unlocked Google Pixel 2 XL, for the more stock-ish/AOSP feel of the OS.
My 75 year old Father, who's still using my VERY old Note 3 needs a new phone, and I want to return the Note 8 to Stock to give to him.
I've followed every guide that I can find on returning to stock, even downloaded the original firmware. Every time I try flashing the original firmware in ODIN, it fails.
Can anyone help my walk through this?
Here's a photo of the splash screen, in case it helps anyone figure out what's going on.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
---------- Post added at 06:42 PM ---------- Previous post was at 05:56 PM ----------
wjcrabtree said:
.....
Here's a photo of the splash screen, in case it helps anyone figure out what's going on.
Click to expand...
Click to collapse
Here's the text from the splash screen, in case no one else can see the photo either:
Build Info: jan 5 2018 11:48:33
Build Info2: SWDG4715:dpi QB:16404812
Build Ver : FA71_N950USQU3ARA1_12824205 [ user ]
Chip Name : MSM8998
Chip Ver : 2.1
PM8998 Ver : 2.0/PM8005 Ver: 2.0
HW Rev : 11
Model Name : SM-950U
SERIAL NUMBER : 0x6C220149
Cable : 0
DEBUG LEVEL : MID
CARRIER : XAA
Fused Open Loop Voltage : 976
CPR_IDDQ_INFO Silver : 0x14
CPR_IDDQ_INFO Gold : 0x34
DDR VERNDOR : Samsung
My note 5 is stuck in start logo couple of days ago and i decides to flash stock rom for SM-N920S.
but odin is stuck on system.img.
my build version is N920SKSS2DTJ2.
i downloaded exact firmware in sammobile here
https://www.sammobile.com/samsung/ga...S2DTJ2/608736/
PRODUCT NAME: SM-N920S
CURRENT BINARY: Samung Official
SYSTEM STATUS: Official
FRP LOCK: ON
Scure Download: Enabled
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3306 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i spend solid 3 days trying different things. i tried different usb cables different ports different computers different odin versions reinstall samsung usb drivers nothing helped.
please help me
darshanamss333 said:
My note 5 is stuck in start logo couple of days ago and i decides to flash stock rom for SM-N920S.
but odin is stuck on system.img.
my build version is N920SKSS2DTJ2.
i downloaded exact firmware in sammobile here
https://www.sammobile.com/samsung/ga...S2DTJ2/608736/
PRODUCT NAME: SM-N920S
CURRENT BINARY: Samung Official
SYSTEM STATUS: Official
FRP LOCK: ON
Scure Download: Enabled
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3306 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
View attachment 5324491
i spend solid 3 days trying different things. i tried different usb cables different ports different computers different odin versions reinstall samsung usb drivers nothing helped.
please help me
Click to expand...
Click to collapse
try flashing with odin 3.12.x
howdeedodat said:
try flashing with odin 3.12.x
Click to expand...
Click to collapse
same result
Okay i extract system.img and convert it to md5 try to flash it alone. same result . it stuck in same position.