Related
This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).
My Nexus 6 fell and the display broke. Not the screen but the display. The scratch's are inside. My device still works but I can't see anything and the touchscreen doesn't work.
What display/screen replacement should I buy?
I was thinking on buying this one: http://articulo.mercadolibre.com.mx/MLM-576031511-pantalla-touch-marco-motorola-nexus-6-_JM
Please check the link and tell me if it's the right thing to buy. Thanks in advance.
A pic of how it looks:
That's the right one.
That replacement has the frame too, if you want to save money and your frame is still in good condition you can just remove the existing frame from the broken screen, no need to worry about hurting the display as it's already broken so just break it loose, in pieces if you have to lol. Then just get one without a frame, just be sure to check the descriptions to be sure they include adhesive tape pre-applied or get a roll of 2mm 3M double-sided adhesive tape for $2 and do it yourself. While your at it you can also use the tape to re-secure your back cover after removing it if it needs any.
::EDIT::
Here is an example of one without a frame:
https://www.amazon.com/gp/aw/d/B00X...eywords=nexus+6+replacement+screen&th=1&psc=1
That seller it's a $40 difference in price without the frame. Also note how the speaker grills are attached to the frame, NOT the AMOLED. Keep that in mind when taking off your broken screen from the frame. If you are unsure if you can do it and feel safer just getting it with the frame, take 10 minutes before ordering and just try to seperate the broken AMOLED from the frame, if you succeed and find it by looking at it just how the new AMOLED panel would attach to the old frame then save $40 and get just the panel, it's already broken, might as well give it a shot, if you don't think you can attach the new panel to the frame yourself after removing the broken panel, order the one with the frame. ?
Thanks guys. I've got some more questions.
What process should I follow to replace the screen, should I dissemble everything? Any video tutorial you would recommend?
And, I've noticed that the phone doesn't heat up when I charge it as it did before (I have a Turbocharger), is the device ok? Is it normal that it doesn't heats up?
It's normal to have it not heat up when charging. Mine doesn't.
Jerryrig Everything has a good teardown video you can use.
What seems weird to me is that the phone usually heated up even if i wasn't using it (I guess fast charge) but now it doesn't.
Is there a way to know if it's charging or know the battery level other than looking and the screen? Because I can't see anything.
You should let the battery completely discharge, so the device turns off. That will help to prevent electrical damage to the components when you are disassembling the phone.
Letting the battery drain to zero is bad for the battery, for one. For two, the battery will be one of the first things disconnected, thus there will be no component damage.
Isley_ said:
What seems weird to me is that the phone usually heated up even if i wasn't using it (I guess fast charge) but now it doesn't.
Is there a way to know if it's charging or know the battery level other than looking and the screen? Because I can't see anything.
Click to expand...
Click to collapse
Typed up a long response then posted and ticket was expired lol. All I can think of right now is the phone still works, just can't see anything. Let the battery die, call the phone to see if it's dead or rings/vibrates. After it's dead plug her back up and see if she starts, can call again to check if it's in fact booted into Android. Maybe someone else can think of a better way, I take it you don't have the LED enabled for charging so that sucks. Like the previous poster said, it is not advised to let the battery drain 100%, one time however won't hurt, just don't do it repeatably. Hope you successfully get her up and running again I still have my pre-order Nexus 6, never a screen protector, just a Seidio Dilex Pro case and not a scratch on the beauty, someone needs to make a SD 835 phone with dual front facing speakers before I upgrade!
LaGgY_42o said:
Typed up a long response then posted and ticket was expired lol. All I can think of right now is the phone still works, just can't see anything. Let the battery die, call the phone to see if it's dead or rings/vibrates. After it's dead plug her back up and see if she starts, can call again to check if it's in fact booted into Android. Maybe someone else can think of a better way, I take it you don't have the LED enabled for charging so that sucks. Like the previous poster said, it is not advised to let the battery drain 100%, one time however won't hurt, just don't do it repeatably. Hope you successfully get her up and running again I still have my pre-order Nexus 6, never a screen protector, just a Seidio Dilex Pro case and not a scratch on the beauty, someone needs to make a SD 835 phone with dual front facing speakers before I upgrade!
Click to expand...
Click to collapse
Try iFixIt https://www.ifixit.com/Guide/Nexus+6+Display+Assembly+Replacement/36090
These fine people are in the town where I live and have very through tutorials. They are also involved in the political battles to allow user repair rights for everything you can imagine, and then some. :highfive:
last year i recommended a colleague to buy this phone (mi a2 lite)
A few days ago, he told me that his son dropped him on the ground and broke the screen. he went to a shop and was asked for € 75.
later, he went to youtube and noticed that it's not that difficult to change it yourself. I searched the screen on the various e-commerce sites and found many. He would like me to help him buy a decent one so that he then undertakes to assemble it himself.
Do you have any to recommend? there are a lot of them and I wouldn't want to waste too much money. He said he needs the screen and any glue needed to attach it.
Many thanks in advance : Highfive:
(I translated everything with google translate to avoid too many grammatical errors ...)
I recommend watching the video in this link to disassemble. Also, Google for other A2 Lite tear-downs to get a good feeling for what you are going to do. As far as which screen to buy, I don't know which is the best but I bought this one. I am happy with it. The only other recommendation I have is to buy the screen AND the frame. It's only a couple more bucks for the frame. Then you just transfer the motherboard, etc... to the new frame/screen. No need to glue anything back and no need to worry about heating up the old screen to remove it.
A couple pointers:
* Be careful removing the fingerprint ribbon cable - it can rip easily (but a replacement can be purchased as well from China).
* Be careful removing the earpiece. I pried it up wrong and it split in half. I had to buy another from the UK which took about 3 weeks to arrive.
*When removing the tape that holds the battery in place, wind it slowly but firmly. If you go fast it will snap and then the battery will be hard to pry out.
Overall, I didn't think it was too difficult. I just had a problem with the earpiece & battery tape. Not bad considering I don't do this everyday.
Good luck!
Thanks a lot for the answer!
I watched the video and read the answers in that other thread too.
As soon as I catch my colleague, I will tell him all these things. I must also remind him that the phone has this middle name (redmi 6pro) so that he can get better information.
A little thing I didn't understand is that he told me he had seen a video showing how the screen was changed. And he told me how it has to be heated for a few seconds in order to detach it. Instead, in the video link in that other thread, it shows how to detach all the components until you get them all on the table. But, the only piece that had to "warm up" is the fingerprint reader.
Clearly, you suggested that I watch other videos on google and since this colleague of mine is not very well versed in the internet and the various ways to "retrieve information" I will have to help him both in recovering instructions and then ... ordering the necessary "pieces".
He told me that in addition to detaching the screen, after heating it ... there was only need to detach a cable or two that connects the screen to the motherboard and the game was done.
There is a thin thread that binds my future skill in recovering assembly and disassembly instructions ... the cost of the components and hoping that he has grasped the concept.
(I hope google translator has translated everything in a decent way xD )
If you follow my advice and replace the screen & frame, you won't need to heat anything to replace it. You just transfer the contents (motherboard, earpiece, etc...) from the cracked screen/frame to the new screen/frame.
The fingerprint reader attaches to the back cover and that gets replaced onto the new screen/frame...so it never has to be removed in the first place.
I found what I did was the best method for me. I tried replacing a screen on a Samsung Galaxy S4 years ago. Heating up the screen wasn't easy since I only had a blow dryer. I ultimately completely destroyed that phone trying to heat/pry the broken screen off, even though the video made it seem very easy. I didn't want a repeat of that so I choose to just transfer the components to the new screen/frame.
this is the video
https://www.youtube.com/watch?v=zNuRf7uOADc&t=437s
I finally found my colleague and told him about this other method.
I showed him (from my phone) the video posted in the other thread.
His response was:
"oh my god how do I put it all back together?
I would be confusing for sure. In the video that I have seen, just heat the front part and then I will only have to detach and reattach only 2 cables. "
he told me that he doesn't have that tool that looks like a hairdryer. But he would like to use a kind of hot metal counter that is used to pack the products in plastic. He would like to put the phone down a few seconds and then take off the screen.
I, if I had been in his place, I would have certainly opted to disassemble and reassemble everything. I do not trust very much to unstick and glue such delicate components.
But I've never tried either, so I have no idea how to make him understand that it's not as easy as it seems.
Assuming, that I have to buy him a screen that allows him to do as he says, which one should I buy? In the sense, I noticed for sale the famous screens with or without frames. But in your case, which one should I opt for?
I hate the fact that I have to take on this big responsibility of having to help and choose what to do.
however this forum is beautiful. As soon as I can I would like to follow him more to read the various topics ...
thank you for the advice not to heat the screen but to follow that method of detaching and reattaching the components but I may not be able to convince him ...
Reassembling the phone is no more difficult than disassembling it. In fact, it might even be easier.
Who is going to do the actual work? You or him? If it's him, let him do whatever he wants...his way. If it's you, then just get the screen & frame and swap components over.
The rest is up to you guys now. He asked you for help/advice. Tell him to let you help/give him advice or he's on his own.
Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
I took mine out of the case tonight to clean it and discovered I have exactly the same problem! My case is such that if I put the phone back in it, the case "snaps" together and hence keeps the phone together. Mine is probably two years old too, so I'm sure no fix is possible (but I'll keep my eye on this thread). I'll leave the case on and begin looking for a new phone.
I'm with Sprint so I'm anticipating the conversion to TMo, so I'd rather wait until that happens before I buy a new one.
dannykewl said:
Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
Click to expand...
Click to collapse
You could try using a hair dryer to heat up the glue to make it stick together again.
You could try using a hair dryer to heat up the glue to make it stick together again.
Click to expand...
Click to collapse
I thought maybe excessive heat and sweat from being in my pocket on hot days loosened it up.
Thanks for the replies FrogFan and Ragarianok. Sorry for the long delay. In the meantime, I got the back case half off, and indeed a swollen battery. I am going to order a new battery for $4 from Mobile Defenders in MI, battery image says Motorola on it, and they say authorized OEM. A nearby repair shop said they will put it in for $20. They said a decent battery should run $20+, but all those higher priced ones on ebay and Amazon are no-names.
Thanks for coming back, dannykewl. I wasted some time inquiring about a fix from Motorola and found out that their "fix" would cost more than the phone was worth. A local shop quoted a ridiculously high price to fix it, too, but they did say the problem could be caused by a swollen battery. I will check with other local shops to see what they'd charge to replace the battery and seal it back up.
Did you get yours fixed?
POP!
My phone separated today and it is a swollen battery. I suspected for about 2 months the battery was swelling because of pressure points showing up on the screen as bright circles. I was just going to buy a new phone as this was a cheap phone and 2 years old, but the battery did the hard work for me by separating the phone from it's back, so I decided to fix. I removed the battery, ordered replacement battery on ebay and will put back together myself for $12. The $4 batteries are out of stock. The phone has enough stickiness left to hold the backplate and phone together on it's own, and it'll be in the phone case so no worries. Might apply a little Elmers to the surround. From what I read online, and saw on Youtube, be careful with the back, it's actually a glass metal hybrid and not safety glass at that. It will shatter off the metal and into little tiny razors and knives. The screen artifacts disappeared when the back was removed, relieving pressure on the components mashing up against the screen from the inside.. No permanent damage. This new battery should tide me over long enough for the affordable 5g phones to come out. I don't buy pricey phones. Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
I took mine to a local repair shop today and confirmed my problem was also a swelling battery. They will replace the battery for me for $75.
Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
Click to expand...
Click to collapse
I checked out a YouTube video on this topic and quickly confirmed that this repair is way over my head. I don't have the tools or the patience to change the battery in this phone.
I'm unhappy with my battery life. While it did work 2-3 days with 4-5h SoT at best before I now get around 25-35% in the evening. Not suitable for another day.
So either the battery is done for or the software has become way way worse.
https://www.witrigs.com/oem-battery-replacement-with-frame-for-sony-xperia-xz2
Battery Replacement does seem possible. So has anyone done it? Did it help?
Yes. I have done a complete screen replacement as well as the battery. I didn't need to watch out for a screen as it were completely destroyed. Yup, you're right about the battery, probably it needs to be replaced. I have a neat trick to help you with screen removal. Take a plastic bottle, cut a small rectangle from it (around 4x6cm should be enough) and then round those sharp corners with some scissors so there won't be any sharp edges left. Once you've that done, take your freshly cut plastic card and insert it into bottom gap (where speaker is). You could use a suction cup to raise the glass a little bit. And slice the adhesive around the screen. Ofc be careful not to push it too far to not damage screen ribbon. Watching teardown videos is crucial as you don't wanna pierce or rip apart the screen ribbon. if you want more information about this, feel free to ask As putting everything together - I recommend buying original lcd adhesive for xz2, it's simple and the screen stays on as well as original.
*#*#7378423#*#* go into this service menu then the battery health test, it tells you current max. capacity and health status whether if you need to replace or not.
battery replacement should be relatively easy since it is held down by screws not adhesive, be careful when opening up the phone you may damage the LCD also make sure you clean all the left adhesive residue before applying the new sticker or B7000 glue to the frame
I don't trust those numbers. That's the Problem here...
@Verity.
Did you realize any difference in Battery life before and after the change?
Certainly. I bought used battery as it was cheap and as the old one was quite worrying on the outside. I immediately noticed the difference (especially in sot) so with the new battery you should feel the difference even more.
Not sure if the degradation of the battery is good or bad...
After fully charging now:
And one of the earliest from 2018
https://forum.xda-developers.com/showpost.php?p=83337497&postcount=6
That's pretty normal. Every battery has a lifespan. It's depended on temperature, usage but the most important factor is the charging cycles. After x cycles battery loses it's capacity. It's due to chemical reactions inside of it and there's nothing you could do about it. Until solid state batteries will come out, you will have to change the battery once 2-3 years.
So yeah....
I've done it and i'm not happy
Haldi's Benchmark Thread for Testing&Fiddling with the Xperia XZ2
Howdy, You might remember me from the Xperia Z2 or the Xperia Z. I've started playing around with Android on my old Sony Xperia X10i and i've always liked fiddling around with too much data and thoroughly testing what i own in order to fully...
forum.xda-developers.com