Related
I'm not in the habit of complaining about ne1's products but this one takes the cake. This short note is just to warn my fellow forum members:
- In Feb 06, I got a new HP Hw6515 phone. I bought a bunch of stuff from pocketpctechs, screen shields, stylus and these headphone adapters that allows me to hook up my 3.5mm headphones and jacks to the phone's 2.5 mm jack.
- I have an 3.5mm aux input on my car stereo also and pocketpctech's angled 2.5mm/3.5mm adapter allows me to use the phones mic when I'm on the phone.
- One day, I find my phone's audio totally silent. Sure, it's probably the switch in the phone's jack which may get stuck occassionally and as commonly reported in these forums as well.
- Alas, that is not to be. This time the tip of the pocketpctech's phone plug has dislocated and lodged itself in my HP's phone jack. All attempts to remove it were furtile.
- The end result was a whole bunch of hassle, the phone can only be used with a bluetooth headset since that's the only thing that will bypass the phone's speaker output.
- I requested for a Cingular warranty replacement and they sent me a refurbished one. I was ticked off about the replacement but subsequent phone calls to Cingular did not yield any progress in getting a new replacement unit.
- I decided to sell the replacement refurb to a friend at a $200 loss.
- I called pocketpctechs and told them about the adapter, they apologized and sent me a replacement promptly.
- I then went out and bought a Cingular 8125.
- I was informed the mic won't work using these pocketpctech adapters with the 8125 but (a) I already have them and (b) the angled design places less stress on the phone jacks.
- Well, guess what? On week two, I took a call one evening and could not hear anything. That's right, I had earlier on, used another pocketpctech adapter, this time was the one in the car on my commute home. To my horror, I discovered the end tip of the pocketpctech adapter in my car was missing!!
- I attempted to remove the tip with an assortment of tools, screwdriver, wire e.g. to no avail as the whole plug itself was starting to loosen up.
- I later found out that one can access the plug from the battery compartment but at this point the plug was messed up.
Post-mortem
- I used the warranty service again and yes, I received a refurb one as well.
- I searched the boards for similar issues but have only seen one mention where the 'tips' may come off. I can only guess that with bluetooth, using the headphone jacks may not be too popular so folks may not have encountered this phone yet.
- I called pocketpctechs just to inform them about this 2nd incident. They asked me what I would need and I told them I don't want ne thing but just wanted to let them know so others don't suffer my fate.
- BTW, the $3 stick adapters I bought from a local electronic store are working dandy.
- The next day, I decided I will keep and use the refurb replacement one since it looks fairly new.
- I emailed pocketpctechs and requested for (a) replacement phone adapter (this time I will yank and pull to make sure it don't come off) and (b) a replacement write shield (except I would like the clear model).
- The following is her reply to my pain and suffering. Like I keep busted adapters lying around! If and when Cingular sends me a bill for repairing the phones after they discovered the tips lodged in the phone jacks, I'll be forwarding them on to pocketpctechs. I would be nuts to send them ne more money!
"We will send you one more PPCPADPT11. However, we will need you to send back all the faulty adapters you have received from us so we can submit them to our manufacturer. We need to have the faulty adapters back in our office before we can send you a third replacement. We have been making these adapters for years and never had this complaint. We need proof to show both my supervisor and our vendor so we can justify sending you three replacement adapters. Before we send you a third replacement, we will have our head technician inspect and test the adapter. It will not be faulty.
We will not be able to send you a C2 WriteSHIELD to replace the AG you orignially ordered. We can only send you what you ordered. If you would like a C2 WriteSHIELD for your Cingular 8125, you will need to pay for one. Please advise. "
I bought the one from boxwave and have never been happier
http://www.boxwave.com/products/dua...free-stereo-adapter-cingular-treo-650_550.htm
and yes i have an 8125
exstatica said:
I bought the one from boxwave and have never been happier
http://www.boxwave.com/products/dua...free-stereo-adapter-cingular-treo-650_550.htm
and yes i have an 8125
Click to expand...
Click to collapse
Nice! I think I'll order two of these. Thanks.
Wow I am wanting to replace my usb miniport myself I have the AT&T Tilt 8925/HTC Kaiser. The other day I was trying to reset the phone In the Dark thought that I was pressing the reset button on the bottom of the phone, what was happening I had my styles in the usb port DAM IT!!!! Next thing you know I go to charge and the USB port just falls back I then open the unit, and find the usb port has broken from the motherboard, seems to be a pretty clean break, all I need is a new MINIPORT does anyone know where I can buy? An OEM port...
Please HELP!!!!
Afrojack
HELP USB Miniport Broke
Can someone help I have an issue, I broke my usb port, I have the phone opened, I was able to access the usb port it has been completely broken off the board, seems to be broken of clean no cracks on the board, all I need is the usb port does anyone know where I can buy a miniport? Also the correct size of the head for the Soldering pen? Is there anything else I may need to repair this issue. Keep in mind I have the phone open, and Have the ability, but if there is any more steps I may use I would really appreciate it. Thanks
AfroJack
Is this a common problem? Mine is now loose, and it will be so annoying of it breaks off the mobo.
I don't know anywhere where you can buy the miniport, but surely warrantee will cover fixing the miniport?...
I did almost the exact thing a couple days ago. I only noticed now from this post. My pins were bent but it didn't break. I had to bend it pretty far so my charger would work again. Do you have pictures of what it looks like from the inside? Maybe you can buy a cheap device with the same pin layout?
No Picture
No I dont could take one, the usb port broke off the board I have talked to PocketPCTechs.com They will sale me a USB Port for $25.00 dollars I wish they had a picture of it maybe I will call them for a picture. They also said they will fix it for $79.00 dollars. I would like to do myself but for 79.00 dollars well I think it is well worth it.
I had the same problem 25 for the part 0 for a local company to put it in. pocketpctechs does give you the mogul usb port which I think is better than what comes standard on my kaiser. (humorous fact htc wanted $350 and 3 wks to fix it)
its not covered under warranty its considered misuse
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser
there are disassembly pics somewhere on this page, if your comfortable soldering it shouldn't be a problem. did it w/ my 8525.
Hey maybe you can extract the port from this:
http://cgi.ebay.com/New-HTC-MINI-US...ryZ20336QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
I get one like the one I posted and it has the HTC symbol on it and everything. It looks OEM to me. Well the mini usb port on there to where you can plug in the headphones has all the pins on there and it seems like you would be able to just extract the one on the adapter for much cheaper. (around $5)
HTC repairs
I recently sent my kaiser to htc repairs USA austin tx and had to give them my credit card number. Anything they find broken not covered by the warranty they fix for $28 which seems cheap since you know they will repair it the right way. Also its oem parts
Hey I am currently living in Austin, TX for school. I just have an ATT Tilt and am not with ATT so I am probably not covered by anything.
damn, smaething happened to me , but it didnt broke off the phone, now that i look at it the usb thing its bend, now I know why the charger didnt want to plug in yesterday...
HTC has a one year warranty and as I stated befor they will fix non warranty items for only $28. That is what I was told when I sent in a Tilt that was not with AT&T.
I think mine must be bent or something too. The USB goes into it to charge, but it falls out really easily. It's not as big of a deal if i am charging it at my house and just leave it alone. The problem is when I'm in my car and it moves around and the charger falls out when it just slides a little bit.
taylor310 said:
I think mine must be bent or something too. The USB goes into it to charge, but it falls out really easily. It's not as big of a deal if i am charging it at my house and just leave it alone. The problem is when I'm in my car and it moves around and the charger falls out when it just slides a little bit.
Click to expand...
Click to collapse
Thats how it started with my apache, now it doesnt charge at all. I found a site on google, search for PPC techs and they do the repair for $60, but you have to be without the phone for that time.
Tilt port repair from HTC USA
Called them about a port repair and was told it would probably be around $350 since it is part of the main board. Might be covered under warranty, up to the technician to determine if it is a normal failure or customer caused.
Too big a crap shoot!!
I just had the same thing happen, and they also told me it was "user error" and that it would be $300+ to fix...... this is clearly a manufacturing/design error and should be covered by warranty!
Big_Dutch said:
I just had the same thing happen, and they also told me it was "user error" and that it would be $300+ to fix...... this is clearly a manufacturing/design error and should be covered by warranty!
Click to expand...
Click to collapse
Just bumping this thread because I have the same problem. One of the metal pins inside the usb port ended up being "pushed down" so my phone wouldn't charge/connect to activesync.
It might be time to move on from an HTC phone, I guess.
The phone was a refurb though, and I've had it for 8 months.
I've had my tilt for a little over two years now and it seems the hardware has finally gave in. About two weeks back, the phone repeatedly got got stuck in a white screen when returning from sleep mode (as identified here: search "white screen issue"). I chose to dismantle the phone and replace the flex cable with one I had salvaged from my friend's dead tilt. Fortunately the white screen went away. In turn, I lost the use of the memory card slot, the touchscreen functionality only worked in landscape mode, and worst of all my sim card is no longer identified. Trying to revert back to my old tilt's flex cable gave me a empty screen all together. My question is, whether I should purchase both a new flex cable and screen or whether a flex cable alone will do? Moreover should I take a chance and dismantle an old tilt sold on eBay? Or just buy a new cable shipped all the way from China as there seems to be no US sellers? Any and all advice is welcome.
Sounds like you may have a loose/bad connection plug, need to recheck assembly.
The old ribbon probably failed completely due to extra stress during dissembly.
Parts from china are mostly copy parts & the quality is normally awful, buying a salvalge phone is a good option if price is right.
For sure a few forum members will have Kaiser spares.
Mister B said:
Sounds like you may have a loose/bad connection plug, need to recheck assembly.
The old ribbon probably failed completely due to extra stress during dissembly.
Parts from china are mostly copy parts & the quality is normally awful, buying a salvalge phone is a good option if price is right.
For sure a few forum members will have Kaiser spares.
Click to expand...
Click to collapse
Thanks for the response, but I disassembled time and again to check the connectors with the utmost care mind you . After some thought, I decided the salvage phone was not a a good option as those may have severe wear on the cable as well and I'm not willing to wait around for a week for the item to arrive to find its dysfunctional (or nearing its fate). Fortunately, I found a legitimate eBay seller in NY who has the new flex cable. Hopefully if the phone recovers, I will update for those who might come upon this thread and have found themselves in a similar situation.
My Note 8 mic died today :crying: I can hear the callers but they can't hear anything from me. If I switch to speaker, they can hear me. I checked all settings and did factory reset, didn't solve the problem. I took it Samsung service center at Rama 9 Bangkok ( I live in Thailand). They tried "deep" re-flash (whatever that means), but didn't fix. Seems like my phone failed their diagnostics as well. They opened up the phone and confirmed it's a hardware failure. Fortunately, everybody who preordered Note 8 over here get 6-month brand new unit replacement and 1-year accidental screen damage warranty as part of promotion in addition to free AKG 230 blutooth speaker, some military grade cover, pencil style s-pen. So for this case, they processed mine to get brand new unit as replacement. I have to wait 7 to 14 days. I really hope my replacement phone will be problem free.
I'm just glad I haven't purchased whitestone and only bought some cheap screen protectors. I was also considering of rooting it. Now that this happened, I don't think I'm going to do it at least until my warranty runs out. I really don't want to lose my accidental screen damage warranty. I have a feeling that I'm will be using it.
Sitti01 said:
My Note 8 mic died today :crying: I can hear the callers but they can't hear anything from me. If I switch to speaker, they can hear me. I checked all settings and did factory reset, didn't solve the problem. I took it Samsung service center at Rama 9 Bangkok ( I live in Thailand). They tried "deep" re-flash (whatever that means), but didn't fix. Seems like my phone failed their diagnostics as well. They opened up the phone and confirmed it's a hardware failure. Fortunately, everybody who preordered Note 8 over here get 6-month brand new unit replacement and 1-year accidental screen damage warranty as part of promotion in addition to free AKG 230 blutooth speaker, some military grade cover, pencil style s-pen. So for this case, they processed mine to get brand new unit as replacement. I have to wait 7 to 14 days. I really hope my replacement phone will be problem free.
I'm just glad I haven't purchased whitestone and only bought some cheap screen protectors. I was also considering of rooting it. Now that this happened, I don't think I'm going to do it at least until my warranty runs out. I really don't want to lose my accidental screen damage warranty. I have a feeling that I'm will be using it.
Click to expand...
Click to collapse
Always sad to read this sort of post. As you know there will always and I mean, always be lemons. Try not to let this sour your Note 8 experience though. I do hope you get this situation resolved in a satisfactory and speedy fashion.
Let us know how you get on. :highfive:
Ryland
The weirdest part is that the mic is the same either for regular call or speaker, the only thing that changes is the output audio source...seems more of a software issue than hardware, that for some reason is not opening the mic on regular calls...[emoji848]interesting...
Sent from my iPhone using Tapatalk
tanquef said:
The weirdest part is that the mic is the same either for regular call or speaker, the only thing that changes is the output audio source...seems more of a software issue than hardware, that for some reason is not opening the mic on regular calls...[emoji848]interesting...
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Very good point. :highfive:
Ryland
Looks like I'm not the only one having this problem
https://www.youtube.com/watch?v=-zZjiaPBp90
https://us.community.samsung.com/t5/Galaxy-Note-Phones/Note-8-mic-only-works-on-speaker/td-p/166661
Do you have a case on it? Take it off.
I ask because I first used a hard case and the mic didn't work always...the bottom port seemed partly covered, not much but obviously enough. Take the case off and all good. I now use a goospery soft case and it's fine.
tanquef said:
The weirdest part is that the mic is the same either for regular call or speaker, the only thing that changes is the output audio source...seems more of a software issue than hardware, that for some reason is not opening the mic on regular calls...[emoji848]interesting...
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
While I don't know which microphone is used for what, I'm pretty sure Note 8 has 2 microphones: 1 on top and 1 on bottom, so maybe it is using top mic with speaker on, not the bottom one?
pete4k said:
While I don't know which microphone is used for what, I'm pretty sure Note 8 has 2 microphones: 1 on top and 1 on bottom, so maybe it is using top mic with speaker on, not the bottom one?
Click to expand...
Click to collapse
Both are used for noise cancelling
Update. I got my sealed brand new replacement couple days ago. My new phone is manufactured in Sep 29th. Everything is good. Mic is working. Screen is good, no light bleed at all. They even unboxed and did diagnostic of new phone with me, mainly checking the screen for any dead pixel or touch sensitivity issue, before I signed paperwork. I'm super happy with Samsung Thailand services, far far better than in the US.
Now let's see if I'll ever have to use 1-year free screen replacement. I nearly dropped it this morning.
That's a hell of a promotion. Wish we'd get that here in the States. The Galaxy 360 camera I made the mistake of choosing (instead of a sd card/fast charger) is a piece of doodoo.
odesskiy said:
That's a hell of a promotion. Wish we'd get that here in the States. The Galaxy 360 camera I made the mistake of choosing (instead of a sd card/fast charger) is a piece of doodoo.
Click to expand...
Click to collapse
My wife got the 360 camera during the S8 promo for a "mere" $50 extra. It's still sitting in the box and not being used. Waste of money for us it was.
Was actually thinking about using it. , Does it have any real uses ?
Sent from my SM-N950U using Tapatalk
Sitti01 said:
Update. I got my sealed brand new replacement couple days ago. My new phone is manufactured in Sep 29th. Everything is good. Mic is working. Screen is good, no light bleed at all. They even unboxed and did diagnostic of new phone with me, mainly checking the screen for any dead pixel or touch sensitivity issue, before I signed paperwork. I'm super happy with Samsung Thailand services, far far better than in the US.
Now let's see if I'll ever have to use 1-year free screen replacement. I nearly dropped it this morning.
Click to expand...
Click to collapse
Mine is giving trouble too, but the entire circuit board there seems to have died on me after about a week, the LTE strength suddenly became terrible, and I found that if I applied pressure on one of the antenna connectors in a specific direction the strength would jump up to normal.
I'm waiting for replacement parts to be available, and I noticed that the USA version that ifixit has a teardown guide for has a newer revision of this board, made a week or so after mine. Must have had some of the early ones fail prematurely... The rest of my phone works flawlessly, fortunately.
Limeybastard said:
My wife got the 360 camera during the S8 promo for a "mere" $50 extra. It's still sitting in the box and not being used. Waste of money for us it was.
Was actually thinking about using it. , Does it have any real uses ?
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Yes. Put it on Ebay and hope some poor schmuck pays you your $50 for it.
Op, that is the reason to buy only from authorized official dealers! The people who get their devices in grey markets most of the time have troubles with warranties
I have the same issue, blowing into the usb port seems to fix it temporarily. Hope this gets sorted out with a software update.
Hi guys. I recently used a questionable charger with my phone (leeco le 2 x526) and since then it has been problem after problem with the USB port. Immediately after that charge, the phone stopped charging with the supplied quick charging brick. It won't even charge slowly. The phone behaves like the charger is being plugged in and out about five times and then completely stops as if the charger is no longer detected. However ,when I put it in a normal slow Samsung charger, it charges to the end without disconnecting.
It's not only the charging that's not working. A Windows PC I have connected the phone to before doesn't recognize it so mtp doesn't work. The PC says the device has malfunctioned and windows does not recognize it. Lately the phone has started rebooting randomly so it seems like I need to fix it soon.
Also, when I plug in headphones using the 3.5mm dongle, I hear crackling sounds for the first few seconds and Jack detection doesn't work sometimes until I reboot. Sounds play okay when it's detected. The microphone and media control buttons on headset have stopped working and I hear static when I press the buttons on my headset, sometimes it's quiet.
I'm pretty sure the USB board is the one that's damaged but want to know if anyone else has faced this issue. If it's the USB+mic board that's damaged I'll order one on AliExpress. I found it for like 8 bucks.
I'm thinking I have a hardware failure because since it started acting up, I tried to flash a ROM clean and got an error in TWRP. The flashing finished but I saw a red error message:
Code:
rcv error in uevent
I googled and this error occurs when the kernel fails to initialize a hardware component.
Has anyone experienced the same problem? I don't want to replace the board without a second opinion.
I believe that you are definitely on the right track with the replacing board, this same exact issue happened to me once on my first Leeco X727. In my case I was lucky enough that Amazon agreed to exchange it for a new phone. Without a doubt, many Le Pro 3 owners have seen this exact issue. Your questionable charger possibly shorted out the USB card.
I would strongly suggest that you replace the battery, while you are at it, it will also be very cheap.
You will need to use a Heat gun to remove the display without damaging the LCD, there are many videos on youtube that demonstrate the quick sweeping technique and the glue will easily release enough that the screen will come off simply by turning the phone onto its face side.
While you can also use a hairdryer, you will need to run a guitar pick along the edge of the screen to remove the display and it's very easy to damage the LCD...I did! Consequently, I bought a heat gun at harbor freight for $ 7 dollars, to easily the display on a friends X720.
Good Luck.
PS : Did you receive your Le Pro 3 yet?
tsongming said:
I believe that you are definitely on the right track with the replacing board, this same exact issue happened to me once on my first Leeco X727. In my case I was lucky enough that Amazon agreed to exchange it for a new phone. Without a doubt, many Le Pro 3 owners have seen this exact issue. Your questionable charger possibly shorted out the USB card.
I would strongly suggest that you replace the battery, while you are at it, it will also be very cheap.
You will need to use a Heat gun to remove the display without damaging the LCD, there are many videos on youtube that demonstrate the quick sweeping technique and the glue will easily release enough that the screen will come off simply by turning the phone onto its face side.
While you can also use a hairdryer, you will need to run a guitar pick along the edge of the screen to remove the display and it's very easy to damage the LCD...I did! Consequently, I bought a heat gun at harbor freight for $ 7 dollars, to easily the display on a friends X720.
Good Luck.
PS : Did you receive your Le Pro 3 yet?
Click to expand...
Click to collapse
Thank you so much for this advice. I will replace this board and see if it solves the problem. About the heat gun, I don't know if I will use it much after this repair so I'll take the phone to my friend who has a repair shop to change it for me.
One quick question... Is there a high possibility of damaging the battery during this repair? I don't want to replace it if I don't have to because mine is still pretty good and keeps like a new one. I don't have much luck with AliExpress because the original batteries for Le 2 cost almost $150 to ship. The rebranded batteries cost less to ship (~$10) but I don't know which one is reliable.
My Le pro 3 is still in transit. I reckon it's still about 2 weeks away because shipping takes very long to my country. I'm just now going through the various development threads to find a good ROM for it. Thanks again -- you're a godsend ???.
twistyplain said:
Thank you so much for this advice. I will replace this board and see if it solves the problem. About the heat gun, I don't know if I will use it much after this repair so I'll take the phone to my friend who has a repair shop to change it for me.
One quick question... Is there a high possibility of damaging the battery during this repair? I don't want to replace it if I don't have to because mine is still pretty good and keeps like a new one. I don't have much luck with AliExpress because the original batteries for Le 2 cost almost $150 to ship. The rebranded batteries cost less to ship (~$10) but I don't know which one is reliable.
My Le pro 3 is still in transit. I reckon it's still about 2 weeks away because shipping takes very long to my country. I'm just now going through the various development threads to find a good ROM for it. Thanks again -- you're a godsend .
Click to expand...
Click to collapse
No problem.
The battery is underneath the heat shield so it will not be affected by the heat gun.
Attached are pictures of my LeEco Pro 3 with and without the main heat shield...On the far left
https://dl.xda-developers.com/thumbs/4/7/3/9/9/6/8/4739968.jpg
( Ignore the writing, I combined those photos for a solder repair suggestion in a unrelated post)
Edit: Opps, that link didn't work to well, here is the actual post link with better quality photos.
https://forum.xda-developers.com/showpost.php?p=79303956&postcount=72
tsongming said:
No problem.
The battery is underneath the heat shield so it will not be affected by the heat gun.
Attached are pictures of my LeEco Pro 3 with and without the main heat shield...On the far left
https://dl.xda-developers.com/thumbs/4/7/3/9/9/6/8/4739968.jpg
( Ignore the writing, I combined those photos for a solder repair suggestion in a unrelated post)
Edit: Opps, that link didn't work to well, here is the actual post link with better quality photos.
https://forum.xda-developers.com/showpost.php?p=79303956&postcount=72
Click to expand...
Click to collapse
I flashed a ROM from 4pda and totally messed the phone up. That ROM failed to boot and to make matters worse, it formatted my data partition. Everything is gone including my backups and I cannot transfer a new OS to the phone because my USB port doesn't work. The only thing I can do now is to shelve this phone until the replacement USB board arrives. You have been of great help and I appreciate it extremely. I'm using a feature phone now until my pro 3 comes. To use any Android app I have to share my wife's phone which just sucks. (She barely puts the damn thing down)
twistyplain said:
I flashed a ROM from 4pda and totally messed the phone up. That ROM failed to boot and to make matters worse, it formatted my data partition. Everything is gone including my backups and I cannot transfer a new OS to the phone because my USB port doesn't work. The only thing I can do now is to shelve this phone until the replacement USB board arrives. You have been of great help and I appreciate it extremely. I'm using a feature phone now until my pro 3 comes. To use any Android app I have to share my wife's phone which just sucks. (She barely puts the damn thing down)
Click to expand...
Click to collapse
No doubt we never realize how much we rely on these devices until they are gone.
You will definitely love the Le Pro 3, it is much more powerful, and the camera is phenomenal.
tsongming said:
No doubt we never realize how much we rely on these devices until they are gone.
You will definitely love the Le Pro 3, it is much more powerful, and the camera is phenomenal.
Click to expand...
Click to collapse
Absolutely true. I have a new found appreciation for my phone. Now that I think about it, with the time I spend on it I think some digital detox is in order.
I received the USB board from AliExpress but it is incompatible with x526. Anybody with information on where I can get a board for x526 please share it here. All USB boards on AliExpress are for x620 and they can't work on x526.
I am actually thinking about looking for the x526 board in India because that's where the phone was built for. I just haven't figured out how to go about it. But I reckon there is a lot more need for spare parts there because of the high number of people using the phone.
twistyplain said:
I received the USB board from AliExpress but it is incompatible with x526. Anybody with information on where I can get a board for x526 please share it here. All USB boards on AliExpress are for x620 and they can't work on x526.
I am actually thinking about looking for the x526 board in India because that's where the phone was built for. I just haven't figured out how to go about it. But I reckon there is a lot more need for spare parts there because of the high number of people using the phone.
Click to expand...
Click to collapse
X620 and x526 are quite different. These two phones share the same case, battery and LCD screen, nothing else.
Here is a link to buy a usb board for x52x:
US $8.99 10%OFF | Used Original USB Plug Charge Board For Letv LeEco Le 2 X520 X526 free shipping
https://s.click.aliexpress.com/e/e9YBAJQ
alqi said:
X620 and x526 are quite different. These two phones share the same case, battery and LCD screen, nothing else.
Here is a link to buy a usb board for x52x:
US $8.99 10%OFF | Used Original USB Plug Charge Board For Letv LeEco Le 2 X520 X526 free shipping
https://s.click.aliexpress.com/e/e9YBAJQ
Click to expand...
Click to collapse
My le 2 is finally back to full working condition thanks to you. This USB board doesn't look used at all. The best part is that mtp and fast charging are working again.