Related
Hi, I have been using my HTC diamond toch for nearly 2 1/2 months. a few days ago, i did a rom update using Dutty's rom update. All went fine duing the update. used the phone for about 5 days nonstop, no issues at all.
But yesterday all of a sudden the phone has swtiched off by itself, now it doesn't switch on. Thought the battery might be dead so i tried charging but the enter buttton area doesnt glow and there is no sign of charging.
I switched batteries with a friend to see whether it was faulty but it is in good condition.
What do u think the issue will be ?
Thanks
Buddhi.
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
same problem here
Dudes.... Chill!!!!
Here's what you can all try ....
First you guys need to know that de HTC does not charge if the rom is inconplete/damaged .
And.....
If your batery is realy dead there is no initial power on the internal battery to manage the chargement.
So ... resolution.
Fist way .
If you know any one that may have an other HTC Diamond you need to swamp batteries so the good Diamond that has the internal bat ok and charge it there.
Second way . this one i did it my self .
Go to a Local ChinaMan store and buy a multimeter and a regular Universal Adapter.
Heres how it hoes ...
Use the Multimeter do figure out the polarity pin's on the battery ex: + and - .
remove / cut one of the plug's from the Universal transformer and also tag the polarity.
set the voltage to be close to 5 V - 1 Amp .
Can be 4,5v or 5.5v no sweat
Conect the cuted wire from the Univ. Adapter to the Diamond Battery respecting the polarity.
Leave it for a wile..... ( Probably up to 1 hour but chec from time to time tme battery temperature and if possible a reading on the bat voltage levels.)
Done!
Put the battery bat and boot your diamond or turn on to boot loader.
**** Attention if you don't have more than 50% of the bat charge compleated you wont be able to flash your phone****
Any questions Just reply back.
same problem...
its just...my battery was full before the upgrading...i was Unlocking my Diamond..and the upgrade didnt move more than 0% just when i looked on my mobile...there was black screnn...pluged it out..tried to power on..nothing..tried to charge...nothing again..i tried hard reset(vol down+power+back+reset)..it just wont turn on..please help me..im in panic
Help, I have the same problem and my battery was fully charged before this happened. Voltage reading is 4.2V on the battery.
I also tested the power button and there is nothing wrong with it, it conducts when pushed.
Usually pluging in the charger should start it up, but it will not start.
Anyone have any solutions?
I couldn't fix mine so phones 4 u replaced it with a touch hd
Mattmanico said:
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
Click to expand...
Click to collapse
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
bughiman99 said:
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
Click to expand...
Click to collapse
I had same problem , no solution yet.
When I had a Mpx220 I had fixed changing a fuse, but I can´t see nothing in internet guides or foruns.
If someone knows how to repair tell us, becouse htc service in our country isn´t good and my device is outdate warranty.
Regards,
Gus
Someone has fixed?
I have the same problem but on my samsung corby GT-i5500. I installed the clockworkmod on my mobile by rom manager and rebooted in recovery, I think i've installed a wrong version and now it does not turn on at all! what should I do? my parents will kill me if they discover that ive broke my phone
Hi,
Some weeks ago, after flashing/testing my cooked rom & using Task29, my TP2 was stucked on the 1st logo screen and I desesperately tried to flash a rom either using the sd card/bootloader method but it remains on 0%.
After many many tries, I was finally able to flash roms again but yesterday when I used Task29, I noticed that the progress bar flashed from 0-100% in less than 5seconds (It was very fast which is not normal). Usually this process takes at least some 20seconds to complete. After that, my phone is again stucked at the 1st logo screen.
Edit for update : Phone is working again! Don't know how but it just flashed today!! I think I have tried at least 70-100 times before it decides to start flashing!!
It's normal that task29 is a lot quicker than a regular ROM flash. Also, after the task29, it's normal that the phone hangs on the startup screen, because it hasn't got a ROM to load any more. What you need to do is put it into the bootloader (hold down the Volume Down button and press reset), wait till it comes up and says "Serial" on the tri-coloured screen, then plug into the PC and that should change to "USB".
Then you should be able to go ahead and flash a ROM. I presume you have HardSPL ? (I guess so, or task29 wouldn't have worked).
thanks for the reply. Yes, indeed I know the process of task29 since I have been flashing a lot of times. The fact is that the last time I did the task29, the progress bar completed in a flash (i mean, it jumped from 0% to 100% faster than usual). And since that, phone is stucked again at the logo screen. The last time I got this problem, I had tried to flash numerous times for 2 full weeks before the phone finally flashes a rom. Is it that task29 screwed the phone's memory/bootloader? Forgot to mention that it is a Vodaphone UK Rhod100 model.
Ah ok, sorry for misunderstanding.
I wonder if something odd has happened to your HardSPL. Is it still showing "0.85OliNex" ? I wonder if re-doing HardSPL might help ?
steviewevie said:
Ah ok, sorry for misunderstanding.
I wonder if something odd has happened to your HardSPL. Is it still showing "0.85OliNex" ? I wonder if re-doing HardSPL might help ?
Click to expand...
Click to collapse
Yes, it's still on Olinex hardspl - can't re-do the hardspl since everything I tried is stucked at 0%.
What was the last thing that happened when the phone was still working ? You mentioned that you were testing a cooked ROM, is that your own cooked ROM ? Are you sure you haven't bricked your phone ?
Well, the problem started right after using task29 yesterday night - so the rom is not at fault because I flashed the same rom many times before. Phone also was working fine (never dropped or no damages - still in mint condition). What do you mean by "bricked your phone"?
What I was wondering is whether you cooked your own ROM yourself, and this is somehow responsible for the current state of your phone (e.g. by cooking in something damaging to the phone). But it sounds like this isn't the case.
Previously, some people have reported problems like this when there's a USB problem. Have you tried a different USB cable, just to see if that helps ? Or looking very closely at the pins of the USB connector on the phone to see if they could be damaged ?
You mention that flashing by SD card doesn't seem to work either. Have you had that working ok before ? Because sometimes it can be sensitive to the make of SD card, as well as how it's formatted.
thanks for the advices, steviewevie. I really appreciate All the usb pins seems to be in good condition and yes, I've tried 3 different usb cables but to no avail. If there were a problem with the pins, I believe that the phone would have problems to sync with the computer and I did not encounter this situation in the past. I assume the usb is ok.
As for the cards, I have only used Transcend ones formatted to Fat32 - never tried to flash using sd before until I got this problem.
Try searching for some details on the "mtty" tool. It might be that you can use that to help - mtty gives you some commands you can use to the bootloader.
Already tried the commands from "The DEFINITIVE MTTY Thread!!" before and phone is still stucked. Anyone can help please??
Please help me too!!
I do task29 when it finished it's show 1st boot screen,Then i pull the battery out.(Finished Every process of Task29)
1 hour later,I want to flash new rom.I try to enter bootloader,it can't and i try to turn on my Rhodium too.I think that battery out of power then i go to charge it.
3-5 minutes it's wake and show 1st boot screen and turnoff itself.again and again.
Is it bricked yet?
thanks
ravenholm said:
Please help me too!!
I do task29 when it finished it's show 1st boot screen,Then i pull the battery out.(Finished Every process of Task29)
1 hour later,I want to flash new rom.I try to enter bootloader,it can't and i try to turn on my Rhodium too.I think that battery out of power then i go to charge it.
3-5 minutes it's wake and show 1st boot screen and turnoff itself.again and again.
Is it bricked yet?
thanks
Click to expand...
Click to collapse
What happens if you just leave it charging for some time, is the charge light coming on ?
ravenholm said:
Please help me too!!
I do task29 when it finished it's show 1st boot screen,Then i pull the battery out.(Finished Every process of Task29)
1 hour later,I want to flash new rom.I try to enter bootloader,it can't and i try to turn on my Rhodium too.I think that battery out of power then i go to charge it.
3-5 minutes it's wake and show 1st boot screen and turnoff itself.again and again.
Is it bricked yet?
thanks
Click to expand...
Click to collapse
sounds to me that it could be the battery is out of power. Maybe try to leave the battery in with the power cable for a short period of time and see if you can turn it on and flash the rom.
yes,the charge light is on.but 3-5 minutes of charging.it's wake and show 1st boot screen and turnoff itself.again and again too.
Before i do task 29 battery has 46 %.i think the battery left power about 30%.
ravenholm said:
yes,the charge light is on.but 3-5 minutes of charging.it's wake and show 1st boot screen and turnoff itself.again and again too.
Before i do task 29 battery has 46 %.i think the battery left power about 30%.
Click to expand...
Click to collapse
Thats definitely a issue with the battery, Not enough power is getting to your battery maybe after a bad flash or something you did wrong.
I seen a similar issue when my battery was dead and I tried charging it via usb the device would turn on then loop n turn itself off . 5, 10 mins later it did the same thing. . .
Is my battery dead yet?
If i buy a new one,Does it work? Or How to fix this problem?
Thanks in advance
ravenholm said:
Is my battery dead yet?
If i buy a new one,Does it work? Or How to fix this problem?
Thanks in advance
Click to expand...
Click to collapse
Do you know anyone with the same phone as you that could charge your battery ? Otherwise you might need to buy another battery. I would have *thought* that a new battery would be charged, but this is only a guess, and it might depend where you buy it from. I don't suppose you have a lot of options though.
ravenholm said:
Please help me too!!
I do task29 when it finished it's show 1st boot screen,Then i pull the battery out.(Finished Every process of Task29)
1 hour later,I want to flash new rom.I try to enter bootloader,it can't and i try to turn on my Rhodium too.I think that battery out of power then i go to charge it.
3-5 minutes it's wake and show 1st boot screen and turnoff itself.again and again.
Is it bricked yet?
thanks
Click to expand...
Click to collapse
By the first boot screen you mean the HTC screen? Then you did something wrong. Then it's normal that the phone would reboot or turn itself off.
Are you sure you try entering the bootloader the right way? Keep volume down + power on button pressed until you see the bootloader. I mean really keep them pressed until the bootloader shows up.
I can't enter to bootloader and I can't turn on my phone without charger.
**CAN'T USE USB CHARGER TO ENTER BOOTLOADER TOO
That i told from last post i charge my phone and 3-5 minutes it's show 1st boot screen [HTC] and turnoff itself.I charge it for 6 hours then i try to turn it on,it can't.it like battery out of power.I think my battery is dead
Thanks all reply XD
My Mi3 has switched off automatically and doesn't start again. The charger when plugged, the notification light keeps blinking red and when I removed it from charge and again plugged in, the phone is blank, the notification light also does not show up. I tried to boot into recovery by pressing volume up+power button, but that also doesn't work. I did not root my phone and I am on official miui v6 Rom. Please help!!
Try fastboot mode (power+vol down). If that doesn't work either then it's a hardware problem. If it works then proceeed to use Miflash in order to fix it.
From past 7hrs I've put the phone on charge and the red notification light still blinks, my phone is on now nut the charging % still shows 0 I don't know what to do
Use other charger.. Been through that prob.. I use 2A note 3 charger..
I've got an M8 charger as well, I'll try putting up that charger for Mi3 now..
I finally succeeded to boot into recovery mode, thought to wipe all data.. I selected wipe all data and now it's stuck at 98% and nothing is happening.. I am sick of it now. What do I do?
harshjain430 said:
I finally succeeded to boot into recovery mode, thought to wipe all data.. I selected wipe all data and now it's stuck at 98% and nothing is happening.. I am sick of it now. What do I do?
Click to expand...
Click to collapse
it seems you are using the mi recovery and wiping by mi recovery usually takes times just dont be in a hurry let it wipe it will take time and it usually get stuck at 98 but eventually will be 100%
once u wipe everything and flash a new ro dont forget to flash a custom recovery as well
ZenR2 said:
it seems you are using the mi recovery and wiping by mi recovery usually takes times just dont be in a hurry let it wipe it will take time and it usually get stuck at 98 but eventually will be 100%
once u wipe everything and flash a new ro dont forget to flash a custom recovery as well
Click to expand...
Click to collapse
I flashed into recovery not to flash a new Rom but to hard reset the phone.. and yes you were right, my phone did wipe completely( needed some patience at that time ) and now, after hard reset, my phone stayed normally but the charge was 0% and ids not charging.. what might be the problem??
Maybe you should use miflash and flash a new ROM via fast boot mode
Sent from my MI 3W
Ran into the exact same problem yesterday. You need to use a higher output charger. After three different chargers, I came back to the original Mi3 charger and it started charging. I later used Ampere from the Play Store to see the output of different chargers and saw that this red-light blinking only comes with chargers having low output.
I have exactly the same issue. phone switched off and refuses to charge/boot.
whenever, i connect it to charger the red light comes up, the red light will be off after a while even when charger is kept connected.
again if i disconnect and connect the charger, the red light would come back.
sanjay_ara said:
I have exactly the same issue. phone switched off and refuses to charge/boot.
whenever, i connect it to charger the red light comes up, the red light will be off after a while even when charger is kept connected.
again if i disconnect and connect the charger, the red light would come back.
Click to expand...
Click to collapse
I have exactly the same problem! And after a while the LED switch to Green, but when I try to start that phone, it doesn't work and screen only flashes few times and battery is recharging again from 1%
Useful guide
There are two methods suggested for you :
1. Hard turn on (just like taking out the battery for other phones) // Try this first
2. Try entering your recovery and reboot (or perform factory reset) in it.
To hard turn on:
1. Long press the power button for at least 10 seconds. Don't release until you see the Mi logo. Sometimes, more than 10 seconds is required. It depends on your case.
2. Release when you see Mi Logo.
To enter recovery:
1. Press the Power and Volume Up buttons at the same time.
2 Release them when you see the Mi logo.
Now, you should be in the recovery mode.
Tell me if it works. Glad if it helps.
harshjain430 said:
My Mi3 has switched off automatically and doesn't start again. The charger when plugged, the notification light keeps blinking red and when I removed it from charge and again plugged in, the phone is blank, the notification light also does not show up. I tried to boot into recovery by pressing volume up+power button, but that also doesn't work. I did not root my phone and I am on official miui v6 Rom. Please help!!
Click to expand...
Click to collapse
Hii..... When i use my device (xiaomi redmi note 4g) suddenly 3 times red notifications light occurs and gets switched off......... When i restart it becomes normal for some days........ Plzz help me out........
Min3r said:
Ran into the exact same problem yesterday. You need to use a higher output charger. After three different chargers, I came back to the original Mi3 charger and it started charging. I later used Ampere from the Play Store to see the output of different chargers and saw that this red-light blinking only comes with chargers having low output.
Click to expand...
Click to collapse
hi there , i am suffering from the same problem. i used an higher powered charger
the thing is, it starts charging when i use apple 10v charger but it is not charging with my own charger,
i hope u get this reply so that i can quickly solve this problem
Try Replacing The Battery
Is it solve yet ??
I have the same problem, suddenly power off, red blinking led when connect to charger....
I replaced the battery, and now my mi3 is good like it was....
Sorry bad english....
The other day, I formatted all the partitions and my phone didn't boot anymore (not even the charging led). When I connected it to the computer, all partitions were visible so I used mi flash to install an old stable (kk) rom and it worked!
Hope this helps.
harshjain430 said:
I finally succeeded to boot into recovery mode, thought to wipe all data.. I selected wipe all data and now it's stuck at 98% and nothing is happening.. I am sick of it now. What do I do?
Click to expand...
Click to collapse
are you using Xiaomi ,then you must using the Mi flash, tutorial search at youtube and search mi flash unbrick.......goood luckk
hi...
I am facing same problem, but after cleaning it by blowing some air in usb and cleaning with cloth it started charging.
everytime i try to charge facing same problem anyhow by some jugaad it starts charging, whats the permanent solution????
I am using m1 note 3. Suddenly the phone switched off and didnt, on for several hours
then i put the charger, the red indidcator is blinking but still phone is not on. What does this mean?
---------- Post added at 08:42 AM ---------- Previous post was at 08:32 AM ----------
how did you remove the battery, when tried doing it, it started sparking.. what should i do now
gahana5150 said:
Is it solve yet ??
I have the same problem, suddenly power off, red blinking led when connect to charger....
I replaced the battery, and now my mi3 is good like it was....
Sorry bad english....
Click to expand...
Click to collapse
Hi!,
Today I was using my Moto g 2014 LTE XT1072 and suddenly it crashed and it got stuck in a bootloop. Im running cyanpop 6.0.1 and TWRP as recovery. Now I get the unlocked bootloader warning, the fibration and than it goes black. Sometimes it get to see a small portion of the cyanpop boot animation, but it stil goes black after that. I can't get into recovery. If I hold the power and volume down button the bootloop stops for 20 secs. After that it begins again. My PC does not spot the phone when I plug it in with Motorola Device Manager installed.
I really do not know what to do anymore. Do I have to buy a new phone? Please save me from the suffering. If you need any more information please ask.
EDIT: Good news everyone! After the battery drained and leaving it alone for 24 houres the phone booted normally. Thanks guys for the help!
have you tried to enter in fastboot mode?
Zagomah said:
have you tried to enter in fastboot mode?
Click to expand...
Click to collapse
Well I can't get into it from recovery, because I can't get excase it. My Pc did start seeing it when its in 'charge mode' (not sure what the real name is), but when I type 'adb devices' in minimal ADB and Fastboot it just says 'list of devices attached'. And when I try 'fastboot devices' it does nothing. Not sure what to know.
Captain_Bacon said:
If I hold the power and volume down button the bootloop stops for 20 secs.
Click to expand...
Click to collapse
While powered off and no cables connected
hold power + vol-down 3/4 seconds (screen stay black) then release the power and keep vol-down pushed (bootloader screen is visible now) release vol-down, .
Not working ? are you sure ?
dr.nic said:
While powered off and no cables connected
hold power + vol-down 3/4 seconds (screen stay black) then release the power and keep vol-down pushed (bootloader screen is visible now) release vol-down, .
Not working ? are you sure ?
Click to expand...
Click to collapse
Will try this at home!
Nope, still the same thing. The loop stops for 20 secs and just continues after
Captain_Bacon said:
Hi!,
Today I was using my Moto g 2014 LTE XT1072 and suddenly it crashed and it got stuck in a bootloop. Im running cyanpop 6.0.1 and TWRP as recovery. Now I get the unlocked bootloader warning, the fibration and than it goes black. Sometimes it get to see a small portion of the cyanpop boot animation, but it stil goes black after that. I can't get into recovery. If I hold the power and volume down button the bootloop stops for 20 secs. After that it begins again. My PC does not spot the phone when I plug it in with Motorola Device Manager installed.
I really do not know what to do anymore. Do I have to buy a new phone? Please save me from the suffering. If you need any more information please ask.
EDIT: Good news everyone! After the battery drained and leaving it alone for 24 houres the phone booted normally. Thanks guys for the help!
Click to expand...
Click to collapse
Nice to know. Moto G family phones tend to suffer from battery-motherboard problems, usually related to current issues. Is your charger at least 1.0A? My Thea's battery drained at school, I tried to connect it to a generic charger and the phone misbehaved and became trapped in a 0% screen loop, and did not appear to grab some charge. I thought to myself "Oh no! My expensive phone is now ruined forever and my warranty is void! What I'm gonna do?" But I walked home, connected it to my old reliable Samsung charger to see what happens and voila! The phone started charging and I could turn it on again.
benjausen said:
Nice to know. Moto G family phones tend to suffer from battery-motherboard problems, usually related to current issues. Is your charger at least 1.0A? My Thea's battery drained at school, I tried to connect it to a generic charger and the phone misbehaved and became trapped in a 0% screen loop, and did not appear to grab some charge. I thought to myself "Oh no! My expensive phone is now ruined forever and my warranty is void! What I'm gonna do?" But I walked home, connected it to my old reliable Samsung charger to see what happens and voila! The phone started charging and I could turn it on again.
Click to expand...
Click to collapse
I used my Nvidia Shield Tablet charger, which is pretty beafy. I experienced somewhat the same thing. Did yours keep trying to boot aswhile?
Captain_Bacon said:
I used my Nvidia Shield Tablet charger, which is pretty beafy. I experienced somewhat the same thing. Did yours keep trying to boot aswhile?
Click to expand...
Click to collapse
Kind of. The phone would not respond nor turn it's LED on. When connected into any charger the phone screen would turn on in the 0% battery screen. If I touched anything, the phone turned off and the 0% screen appeared again. Also sometimes it would just appear again like crazy, like if I killed the bootloader or something alike. After connecting to the Samsung charger, the 0% screen appeared again and the screen turned off. I didn't touch anything out of fear. After three minutes, the Bootloader Unlocked message appeared and finally the phone booted to TWRP's charging screen. I let it charge to 4% and tried to start the phone. The phone booted into CM12.1 and problem solved. I hope these issues never happen to us again. It would mean motherboard degeneration/wearing out/side effect from bootloader unlock and flashing or something alike. Thanks for the answer.
benjausen said:
Kind of. The phone would not respond nor turn it's LED on. When connected into any charger the phone screen would turn on in the 0% battery screen. If I touched anything, the phone turned off and the 0% screen appeared again. Also sometimes it would just appear again like crazy, like if I killed the bootloader or something alike. After connecting to the Samsung charger, the 0% screen appeared again and the screen turned off. I didn't touch anything out of fear. After three minutes, the Bootloader Unlocked message appeared and finally the phone booted to TWRP's charging screen. I let it charge to 4% and tried to start the phone. The phone booted into CM12.1 and problem solved. I hope these issues never happen to us again. It would mean motherboard degeneration/wearing out/side effect from bootloader unlock and flashing or something alike. Thanks for the answer.
Click to expand...
Click to collapse
No probs my friend and I wish you the same. Let the moto gods protect us.
Hey everyone,
I received the phone couple days ago and while its not new its in pretty good shape, i think. So when i started using the phone i noticed that there was a lot of lag waking it from sleep after extended times of inactivity so i decided to factory reset. The day after everything seemed fine with one incident where i left the phone for like 30min - 1hr and it took 10-15 min to wake up. The following morning i woke up and the phone lagged again for prob the same amount of time however the next morning i.e. today i wasn't getting anything after 30 min so waited another 30 min and realized something is wrong so i attempted the hard reset and other tricks (take out battery and hold power button[1min,2min or 3min], hold vol+/-, the home button and then the power button) but nothing happens on or off the charger, no LED, nothing....
Please help!
Sala mandar said:
Hey everyone,
I received the phone couple days ago and while its not new its in pretty good shape, i think. So when i started using the phone i noticed that there was a lot of lag waking it from sleep after extended times of inactivity so i decided to factory reset. The day after everything seemed fine with one incident where i left the phone for like 30min - 1hr and it took 10-15 min to wake up. The following morning i woke up and the phone lagged again for prob the same amount of time however the next morning i.e. today i wasn't getting anything after 30 min so waited another 30 min and realized something is wrong so i attempted the hard reset and other tricks (take out battery and hold power button[1min,2min or 3min], hold vol+/-, the home button and then the power button) but nothing happens on or off the charger, no LED, nothing....
Please help!
Click to expand...
Click to collapse
I suggest you return the device if you can.
Seems like Your device is hard bricked or maybe motherboard has some serious issues
Try connect to computer see if pc detects the device.
Try another battery maybe battery is dead
If you able to go into download mode then flash stock firmware with pit file.
Trex888 said:
I suggest you return the device if you can.
Seems like Your device is hard bricked or maybe motherboard has some serious issues
Try connect to computer see if pc detects the device.
Try another battery maybe battery is dead
If you able to go into download mode then flash stock firmware with pit file.
Click to expand...
Click to collapse
Well, when i tried plugging it into the computer the only notification i get is the sound of the device being plugged in but the Note doesn't respond and nothing comes up on the computer.
As for another battery i dont know where i can get one to test it.
I cant go into download mode; the screen doesnt turn on, no led, nothing. Its like somebody poisoned the phone in its sleep, it is really bizarre for phone to die like this because you think u would see some signs
Sala mandar said:
Well, when i tried plugging it into the computer the only notification i get is the sound of the device being plugged in but the Note doesn't respond and nothing comes up on the computer.
As for another battery i dont know where i can get one to test it.
I cant go into download mode; the screen doesnt turn on, no led, nothing. Its like somebody poisoned the phone in its sleep, it is really bizarre for phone to die like this because you think u would see some signs
Click to expand...
Click to collapse
Phone is hard bricked and motherboard is almost dead.
You can still bring back to life if you able to find a debrick.image for your model in xda
Its complicated and need patients to do it
If you have enough knowledge then do it or otherwise you have to replace entire motherboard.
Trex888 said:
Phone is hard bricked and motherboard is almost dead.
You can still bring back to life if you able to find a debrick.image for your model in xda
Its complicated and need patients to do it
If you have enough knowledge then do it or otherwise you have to replace entire motherboard.
Click to expand...
Click to collapse
alright guess ill study up and try something tomorrow.