Related
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
water30 said:
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
Click to expand...
Click to collapse
what did you do to get to this screen? Is this after or before you upgraded firmware?
GANJDROID said:
what did you do to get to this screen? Is this after or before you upgraded firmware?
Click to expand...
Click to collapse
after upgrade firmware odin show reset but the my tab not reset then i just manual reset (i can take this method for my galaxys ) after that.....
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
primeroz said:
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
Click to expand...
Click to collapse
Read my above post. Go into download mode (volume down + home + power) you'll still have the same image but the phone WILL be in download mode. Then flash your previous firmware and you're sorted.
Sent from my GT-P1000
You probably got that by messing with the kernel. Fund the zImage from the firmware, extract it with a .tar extractor then use something like heimdall to flash the kernel and it should work.
Sent from my GT-P1000 using Tapatalk
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Help please
slaia said:
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Click to expand...
Click to collapse
Having the same problem too... anyone can help?
If you see Phone-!-Pc on the Tab screen it is the download mode.
You can reflash it using Odin, however, you will need to do full Rom flash. I had similar problem and solved it by replashing.
I followed the latest guide published in this forum and Roto-JME rom with reformatting of internal sd.
Phone ! PC error FML!!!
GANJDROID said:
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
Click to expand...
Click to collapse
Where can i download the JM6 zip??
Hey guys,
I tried to manually update my tab to Gingerbread today via Odin, but it kept hanging on select partition (I discovered I used the wrong PIT for the firmware I was going to flash, but as I didn't select the firmware yet that shouldn't be a problem). At last I decided to quit Odin (which might have been stupid...) and try it again. Then it kept haning even earlier, so I tried to restart the device in download mode. However, whatever I try it keeps giving the Phone ! PC sign. If I try to just boot, if I try to go into recovery mode or if I try to go into download mode. I saw a lot of possible ways to solve the problem, but my PC doesn't recognize the tab anymore. If I connect it, it does give the "usb device connected" sound, but there is a popup which sais "USB Device not recognized. One of the USB Devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message". I already tried to reinstall the driver but it doesn't work. Also Odin and Heimdall don't detect any device.
Does anyone know a solution for this problem? Maybe taking the battery out? (for which I have to buy a new triangle screwdriver, so I need to know if it could possibly work first. It takes some weeks to order such a thing I think...)
EDIT: I played around a bit with the drivers again, and suddenly both Heimdall and Odin recognized it. However Odin stopped recognizing it again. Then I pressed "read PIT" in Heimdall, which worked. After that the device started booting up to the Samsung logo animation and then powered off again. Now it doesn't do anything anymore, not even showing the Phone ! PC screen. I'll charge it overnight (maybe it's gone empty during the process), so I hope that helps.....
In some strange way, the phone works again..... So never mind my post above.
Hi, So I have a rooted galaxy tab and i tried to flash a rom using the clockworkmod(app) which you get with root.
afterwards when i flashed the rom the tablet went into the recovery mode and restarted and now is stuck on a bootloop, no matter whatever i try the tablet is not getting into the clockworkmod recovery....
please tell me how do i fix this problem and how do i install a working clockworkmod recovery
Thank you.
please tell if i missed out anything.
The only mode that i can go into is the download mode
i'd say you need to get into download mode...(vol down button and power button at same time), flash your stock rom and kernel and start the process all over again. if you need more help, you're gonna need to tell us what kind of tab ya got, what you weren on before you flashed, etc. all is not lost, hang in there.
Hey guys, I'm really in a bad spot here.
So I installed CM10 on a GT-i9000, worked fine except for the hardware buttons not working. So from there, I decided to install SlimBean (A foolish mistake that I thought was foolproof). And boom, now I am here, stuck in a CWM bootloop, and I've tried factory resetting and all, still boots the same.
I've tried installing other roms, sometimes it reboots during installation and doesn't complete, and even if it does complete, same problem, it boots into CWM. And I've noticed a new Samsung AnyCall Boot logo every since I tried SlimBean.
I've tried updating the kernel, no luck. I bought a download mode jig, but windows does not detect the Galaxy S in download mode with Kies installed. (I think I disabled USB Debugging in CM10)
Any suggestions? This is really stressing me out. I'm prepared to use odin, but download mode is not recognized on my PC.
slicer91 said:
Hey guys, I'm really in a bad spot here.
So I installed CM10 on a GT-i9000, worked fine except for the hardware buttons not working. So from there, I decided to install SlimBean (A foolish mistake that I thought was foolproof). And boom, now I am here, stuck in a CWM bootloop, and I've tried factory resetting and all, still boots the same.
I've tried installing other roms, sometimes it reboots during installation and doesn't complete, and even if it does complete, same problem, it boots into CWM. And I've noticed a new Samsung AnyCall Boot logo every since I tried SlimBean.
I've tried updating the kernel, no luck. I bought a download mode jig, but windows does not detect the Galaxy S in download mode with Kies installed. (I think I disabled USB Debugging in CM10)
Any suggestions? This is really stressing me out. I'm prepared to use odin, but download mode is not recognized on my PC.
Click to expand...
Click to collapse
You will hadware buttons failure when you flash a i9000 ROM on an Anycall M110S ( Korean Galaxy S) , so I am curious are you sure your phone is not an Anycall M110S? since you also getting Anycall boot screen...sounds odd, that i9000 will do that.
For USB connection problems , just try link on Quick Fixes and Solutions link below
slicer91 said:
Hey guys, I'm really in a bad spot here.
So I installed CM10 on a GT-i9000, worked fine except for the hardware buttons not working. So from there, I decided to install SlimBean (A foolish mistake that I thought was foolproof). And boom, now I am here, stuck in a CWM bootloop, and I've tried factory resetting and all, still boots the same.
I've tried installing other roms, sometimes it reboots during installation and doesn't complete, and even if it does complete, same problem, it boots into CWM. And I've noticed a new Samsung AnyCall Boot logo every since I tried SlimBean.
I've tried updating the kernel, no luck. I bought a download mode jig, but windows does not detect the Galaxy S in download mode with Kies installed. (I think I disabled USB Debugging in CM10)
Any suggestions? This is really stressing me out. I'm prepared to use odin, but download mode is not recognized on my PC.
Click to expand...
Click to collapse
Go back your original firmware...
Any updates to this?
I am having a similar situation. I tried flashing ICS ROM to my Anycall Samsung Galaxy S GT-I9000. It is now stuck in recovery mode. I tried doing factory reset and wiping the cache and dalvik cache and tried reflashing. Everything goes fine but gets stuck in the recovery mode - more correctly in download mode but the download mode logo flashes twices and enters to recovery mode.
Any possible solutions to get me out of this mess?
Thanks,
Sid
your problem will be solved with this post:
http://forum.xda-developers.com/showpost.php?p=24831012&postcount=1330
Edit : above url is for S+ your device is S , sorry .
Thanks, but anything similar for Galaxy S? And remember my download mode does not stay, if flashes twice and runs into recovery mode. So if your solution is something to do in recovery mode it will be helpful (or if your solution is to first make me stay on download mode and then flash something using odin I will be thankful)
Regards,
Sid
sidswami said:
I tried flashing ICS ROM to my Anycall Samsung Galaxy S GT-I9000.
Click to expand...
Click to collapse
Check your Model, Anycal does not make GT I9000, it makes only M110S and firmwares / solutions for them vary.
If you have Anycal M110S visit PIT STOP link below to solve your problems
Check Here to chose your forum/Guide by Version of your phone or you will have more problems by using wrong solutions due to different versions of Galaxy S
you can get a rescue kit from My Android Collections and or a solution from My Android Solutions
But First powerdown, pull out Battery, SIM CARD, and EXT.SD card, press power button for a minute, than powerup without SIM and Ext.SD Card....Do remember to backup your contacts, data, images etc and also your EFS folder before flashing a ROM and make sure you have more than 50% battery charge before you attempt any sort of flashing.
worked for me
Hi..also had the boot loop...
fixed that easily by removing the accu..
removing external SD !!
Thats it !
Worked for me !
Later on I inserted the SD again..and everythings fine
beben3 said:
Hi..also had the boot loop...
fixed that easily by removing the accu..
removing external SD !!
Thats it !
Worked for me !
Later on I inserted the SD again..and everythings fine
Click to expand...
Click to collapse
Glad that worked for you, but I for some reason can't be so lucky. I tried to also flash CWM 10 but after the home key not working I decided to flash Slim Bean and now I am stuck. My phone isn't even recognized by Odin any more and I have tried different USB ports and even my laptop with Heimdall. I don't know what to do at this point, but any kind of suggestions would be great. Usually when I get stuck I just flash back to Stock and start all over with a new ROM or kernel but I have no idea where to go from this point.
Hello,
I have installed this "ibtimes . co . uk / articles / 419836 / 20130102 / android421-jellybean-cm101-custom-rom-samsung-galaxy . htm" rom on my (actually my mom's) galaxy ace S5830 and it worked just fine. Before i installed it i made a CWM recovery backup. I wasn't happy with the rom so i wanted to go back to my last one by restoring the backup. first i wiped data and cache and then restored the backup. But now when i tried to reboot the system it got stuck on the Samsung logo and later on it was just a light blue screen. can someone help me please.
Don't worry, you need to flash a stock ROM via Odin. Look at the stickies
Sent from my pet- Megatron™
Chill your phone can be fixed easily
Simple Bro , Download the firmware files from sammobile.com then Google for Galaxy Ace Odin ..I guess the version is 4.38 or something like that ..and make sure you download the cooper file with it then flash the original firmware using Odin.So then your phone is back to how it was when you bought it.
I hope this was helpful.
If you want the instructions on how to do this ..let me know ..I'll give you the link for the files also
Help!
I'm having the same problem.
I tried to install a new rom on my Samsung Galaxy GT-S5830, but when it was supposed to boot, nothing happend.
I tried to install the original firmware using Odin, but the problem is that I can't connect my phone to my computer.
The only thing my phone is able to do now, is showing the charging screen, opening the samsung recovery mode and accessing the download mode.
I really hope that someone could help me!
Thanks in advance.
PS:
My provider is Vodafone (don't know if it's important)
BscorpionII said:
I'm having the same problem.
I tried to install a new rom on my Samsung Galaxy GT-S5830, but when it was supposed to boot, nothing happend.
I tried to install the original firmware using Odin, but the problem is that I can't connect my phone to my computer.
The only thing my phone is able to do now, is showing the charging screen, opening the samsung recovery mode and accessing the download mode.
I really hope that someone could help me!
Thanks in advance.
PS:
My provider is Vodafone (don't know if it's important)
Click to expand...
Click to collapse
Dude! Switch off the phone. Then press the 3key combo to go to Download mode. U don't need to go to recovery either (which is a 2key combo). & ops name should be:-
COOPER_v1.0.ops
Sent Via XDA™ Premium
BscorpionII said:
I'm having the same problem.
I tried to install a new rom on my Samsung Galaxy GT-S5830, but when it was supposed to boot, nothing happend.
I tried to install the original firmware using Odin, but the problem is that I can't connect my phone to my computer.
The only thing my phone is able to do now, is showing the charging screen, opening the samsung recovery mode and accessing the download mode.
I really hope that someone could help me!
Thanks in advance.
PS:
My provider is Vodafone (don't know if it's important)
Click to expand...
Click to collapse
Hi BscorpionII!
As you can open recovery, if you don't have CWM 5.0.2.6 you could install it from your recovery and then try installing another ROM from CWM 5.0.2.6.
You could read this link
"Nielli's [GUIDE] Guides and Tips How to Root SGA, Install CWM5 and install Mods + Downloads"
In the link you'll find the last stable recovery -version 5.0.2.6- and much more.
Good luck.
I Recently received a galaxy s3 lte gt-i9305 from ana other country so no warranty for me
So I wanted to install cm 13 so installed twrp recovery thru odin and it showed PASS in green but when i tried to boot into it there is nothing it just reboots it self back to normal
Then i tried cwm too the same thing
After that I saw a yellow triangle with phone connected to pca and said please connect kies or whatever something like this
So i looked this up then i found that i need to flash stock firmware
And that's what I tried to do
And that never wnts to work always fails in odin
Either at zl.img or cache.img
I tried kies but won't recognize it
Tried octoplus... Loaded and so fast but installed only recovery and boot that's what was in the log
Now can't go to recovery nor boot
When i try that i get the Samsung logo for like... A sexond thn turns off
The only thing that i can do is download mode
Please any one help me pleaase
I didn't even enjoy having the phone it's brand new :crying:
http://www.htcmania.com/showthread.php?t=698436
I don't get it
so do i need to install linux on a usb flash and use it or what ?
please reply asap