I cracked my screen a while ago and just got the time to do the install, but as some of you may know the adhesive holding this turd together is very tough. After blasting with a hair dryer and buying an automotive suction cup I finally got the glass off but it cracked too bad to be reused. I cant do anything with the device now. I've held all buttons for a restart but the broken pixels light up for a split second and then it vibrates for a quick second. as i continue to hold it runs through that process over and over. Even plugging it in to the wall I cant even get a charge light. The only cause i could think of is too much heat. i replaced the screen on a note 5 with no issues. It just makes no sense that it doesn't do anything from peeling the rear glass off. Unfortunately I'm at the parents house where I'm the only android user so i cant plug into a PC as i have the 2 sided typeC cable.
Any Ideas?? As I'm Stumped. And to top it off my spare phone an unlocked Pixel 2 is having the No Sim issue.... Fun times.... It just finished the factory reset and still wont detect my Verizon SIM or ATT. So that's cool, haha.
Thanks for the help. Much appreciate2
Bananas HD said:
I cracked my screen a while ago and just got the time to do the install, but as some of you may know the adhesive holding this turd together is very tough. After blasting with a hair dryer and buying an automotive suction cup I finally got the glass off but it cracked too bad to be reused. I cant do anything with the device now. I've held all buttons for a restart but the broken pixels light up for a split second and then it vibrates for a quick second. as i continue to hold it runs through that process over and over. Even plugging it in to the wall I cant even get a charge light. The only cause i could think of is too much heat. i replaced the screen on a note 5 with no issues. It just makes no sense that it doesn't do anything from peeling the rear glass off. Unfortunately I'm at the parents house where I'm the only android user so i cant plug into a PC as i have the 2 sided typeC cable.
Any Ideas?? As I'm Stumped. And to top it off my spare phone an unlocked Pixel 2 is having the No Sim issue.... Fun times.... It just finished the factory reset and still wont detect my Verizon SIM or ATT. So that's cool, haha.
Thanks for the help. Much appreciate2
Click to expand...
Click to collapse
Stupid question did you reconnect the fingerprint sensor back in? It might need that to be connected to work.
Recheck all the connections again and ribbon cables for any damage maybe it got loose or heat damaged or cut.
BluePhnx said:
Stupid question did you reconnect the fingerprint sensor back in? It might need that to be connected to work.
Recheck all the connections again and ribbon cables for any damage maybe it got loose or heat damaged or cut.
Click to expand...
Click to collapse
Yes its been plugged in and the only thing i damaged was the foam on top of the lock button but its barely peeled back. no visible damage to the cable its self. and with the back cover the only part i took off the only exposed cable is really the fingerprint scanner. The scanner does though have some visible heat damage. there's little spots on it that wasn't there before. I think that's the cause of the problem.
could it be possible that i overheated the battery and now the device is in some kind of protection mode? the device could be thinking that it could catch fire or something? I know that Li-on batteries are pretty fragile to temperature.
Thanks for the help
Bananas HD said:
Yes its been plugged in and the only thing i damaged was the foam on top of the lock button but its barely peeled back. no visible damage to the cable its self. and with the back cover the only part i took off the only exposed cable is really the fingerprint scanner. The scanner does though have some visible heat damage. there's little spots on it that wasn't there before. I think that's the cause of the problem.
could it be possible that i overheated the battery and now the device is in some kind of protection mode? the device could be thinking that it could catch fire or something? I know that Li-on batteries are pretty fragile to temperature.
Thanks for the help
Click to expand...
Click to collapse
If you have a multimeter you can check the battery voltage. If you have voltage then it should be okay but maybe the life of it won't be as long as before. Does the phone charge when you plug it in?
The fingerprint sensor might be the problem. I would replace it as with the battery as well.
Best bet have a Samsung service center look at it, it might be something else.
Good luck with it hope you get it figured out!
BluePhnx said:
If you have a multimeter you can check the battery voltage. If you have voltage then it should be okay but maybe the life of it won't be as long as before. Does the phone charge when you plug it in?
The fingerprint sensor might be the problem. I would replace it as with the battery as well.
Best bet have a Samsung service center look at it, it might be something else.
Good luck with it hope you get it figured out!
Click to expand...
Click to collapse
good thinking on throwing a meter on it. will do that when i get home. it doesn't charge or do anything when plugging into a computer or the wall. any idea what the voltage should be on the battery? is there anywhere i can get values like that for different components of the device? thanks
Bananas HD said:
good thinking on throwing a meter on it. will do that when i get home. it doesn't charge or do anything when plugging into a computer or the wall. any idea what the voltage should be on the battery? is there anywhere i can get values like that for different components of the device? thanks
Click to expand...
Click to collapse
Battery specs should be 4000 mah, 15.4 Wh and 3.85 V.
Even though it will show voltage it might not have enough amperage to run. So might check for amperage as well.
Might want to hook up a light circuit to the battery and place the meter in between the + battery to + side of light (meaning the same line) to measure amps.
If it doesn't charge from the wall might as well replace the battery.
If that doesn't work most likely a dead phone (motherboard).
For any voltage values for the motherboard, sorry no idea if you can find that info.
You've been quite the help Blue. Thank you so much. Will be home tmrw and will check on the device. I'll be sure to come back with findings to return the favor. Thanks again! Hope you had a good holiday and Happy New Year!
Related
Is there a way to Disable Screen Wake up on Charger is Connected on a TW ROM?
I know its possible on some Cm based Rom..
My problem is my usb charging port had a short circuit and shows charging even if its not connected to a charger..
It wakes up the phone and says its connected then it shows not connected.... connected again(screen turns on) and phone heats up all day long.
Samsung service centee is very far from my place so im just finding some workwaround for it..
And I dont want to dismantle my phone myself because I might get it worse...
Help please brothers..
I don't know how mechanically inclined you are, but mine did the same thing a few months ago. I ordered a new usb/charge
board off ebay for less than 20 bucks & did it myself. Granted, I've been a repair tech for over 35 years, but there were several
youtube videos that show you screw by screw how to change it. The replacement board also came with a screw driver (torx)
& a plastic pry tool to get the bezel off the device. Took longer to watch the video than it did to replace it.
If you have any mechanical aptitude, give it a go. Being in my mid 50's, with the bifocals, the screws are pretty small, but
I took the torx driver and rubbed it against a magnet to make sure I wouldn't drop any of the screws
noteandfound said:
Is there a way to Disable Screen Wake up on Charger is Connected on a TW ROM?
I know its possible on some Cm based Rom..
My problem is my usb charging port had a short circuit and shows charging even if its not connected to a charger..
It wakes up the phone and says its connected then it shows not connected.... connected again(screen turns on) and phone heats up all day long.
Samsung service centee is very far from my place so im just finding some workwaround for it..
And I dont want to dismantle my phone myself because I might get it worse...
Help please brothers..
Click to expand...
Click to collapse
p51d007 said:
I don't know how mechanically inclined you are, but mine did the same thing a few months ago. I ordered a new usb/charge
board off ebay for less than 20 bucks & did it myself. Granted, I've been a repair tech for over 35 years, but there were several
youtube videos that show you screw by screw how to change it. The replacement board also came with a screw driver (torx)
& a plastic pry tool to get the bezel off the device. Took longer to watch the video than it did to replace it.
If you have any mechanical aptitude, give it a go. Being in my mid 50's, with the bifocals, the screws are pretty small, but
I took the torx driver and rubbed it against a magnet to make sure I wouldn't drop any of the screws
Click to expand...
Click to collapse
I dont know anything about that.. my job is completely off that..
Well I can completely open a man's abdomen and cut some cancer cells that have metastasize but cant do some opening phones and stuff..
<<<The CRACKS on my NOTE shows how often it KISSES the FLOOR>>>
Amazing isn't it. What I do (electronic service tech) is easy for me, but what you do would scare the hell out of me.
Having someones life in your hand... kuddos!
noteandfound said:
I dont know anything about that.. my job is completely off that..
Well I can completely open a man's abdomen and cut some cancer cells that have metastasize but cant do some opening phones and stuff..
<<<The CRACKS on my NOTE shows how often it KISSES the FLOOR>>>
Click to expand...
Click to collapse
Hello everyone
So a couple weeks ago I took a unexpected swim with my Nexus 6 in my pocket, and haven't gotten it to work since. When I got out I immediately took the phone out of my pocket and turned it off, only to have it boot back into fastboot a few seconds later, turn off, boot to fastboot, and turn of again. It did this several times till it just stayed off. I took it apart, dried it, and cleaned it in Isopropyl alcohol and tried to turn it on but got no response no matter what I did. :crying:
I would consider it fried except whenever I plug it into my charger, the charging icon comes up like normal and even does the battery filling up animation. I replaced the power/volume button strip inside the phone hoping that it was the only problem, but it still would't turn on. I haven't replaced the battery yet because the charging animation shows it's holding charge, but loosing 40ish% after a week and a half of sitting there.
So is there something else I can do, or is it fried? I'm probably going to get a new battery to see if that improves anything, but I honestly don't know what more to do. If anyone has any ideas, I'd love to hear them.
Thanks in advance!
It's fried. Best you can do is send to shop and see if they can salvage it.
Alright, I'll guess I'll have to do that. Thank you for your reply.
I would like to share photos of my phone and seee if anyone vcan help, my situation is kind of similar. I tried to charge after to days of silica drying and cleaning with IPA.
I thin the connection around the battery area isn't secure. Is there a glue that i could buy?
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
oOflyeyesOo said:
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
Click to expand...
Click to collapse
How about sticking the charging coil to the new battery? What type of adhesive is needed?
uncle_buckman said:
How about sticking the charging coil to the new battery? What type of adhesive is needed?
Click to expand...
Click to collapse
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
oOflyeyesOo said:
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
Click to expand...
Click to collapse
I got it kind of working, but the sound is fuzzy and the screen is flickering a little.
I'm missing some screws, so I'll need to buy some new ones.
T3/M3 torx screws, 2mm/3mm height/diameter?
My Nexus 6 fell and the display broke. Not the screen but the display. The scratch's are inside. My device still works but I can't see anything and the touchscreen doesn't work.
What display/screen replacement should I buy?
I was thinking on buying this one: http://articulo.mercadolibre.com.mx/MLM-576031511-pantalla-touch-marco-motorola-nexus-6-_JM
Please check the link and tell me if it's the right thing to buy. Thanks in advance.
A pic of how it looks:
That's the right one.
That replacement has the frame too, if you want to save money and your frame is still in good condition you can just remove the existing frame from the broken screen, no need to worry about hurting the display as it's already broken so just break it loose, in pieces if you have to lol. Then just get one without a frame, just be sure to check the descriptions to be sure they include adhesive tape pre-applied or get a roll of 2mm 3M double-sided adhesive tape for $2 and do it yourself. While your at it you can also use the tape to re-secure your back cover after removing it if it needs any.
::EDIT::
Here is an example of one without a frame:
https://www.amazon.com/gp/aw/d/B00X...eywords=nexus+6+replacement+screen&th=1&psc=1
That seller it's a $40 difference in price without the frame. Also note how the speaker grills are attached to the frame, NOT the AMOLED. Keep that in mind when taking off your broken screen from the frame. If you are unsure if you can do it and feel safer just getting it with the frame, take 10 minutes before ordering and just try to seperate the broken AMOLED from the frame, if you succeed and find it by looking at it just how the new AMOLED panel would attach to the old frame then save $40 and get just the panel, it's already broken, might as well give it a shot, if you don't think you can attach the new panel to the frame yourself after removing the broken panel, order the one with the frame. ?
Thanks guys. I've got some more questions.
What process should I follow to replace the screen, should I dissemble everything? Any video tutorial you would recommend?
And, I've noticed that the phone doesn't heat up when I charge it as it did before (I have a Turbocharger), is the device ok? Is it normal that it doesn't heats up?
It's normal to have it not heat up when charging. Mine doesn't.
Jerryrig Everything has a good teardown video you can use.
What seems weird to me is that the phone usually heated up even if i wasn't using it (I guess fast charge) but now it doesn't.
Is there a way to know if it's charging or know the battery level other than looking and the screen? Because I can't see anything.
You should let the battery completely discharge, so the device turns off. That will help to prevent electrical damage to the components when you are disassembling the phone.
Letting the battery drain to zero is bad for the battery, for one. For two, the battery will be one of the first things disconnected, thus there will be no component damage.
Isley_ said:
What seems weird to me is that the phone usually heated up even if i wasn't using it (I guess fast charge) but now it doesn't.
Is there a way to know if it's charging or know the battery level other than looking and the screen? Because I can't see anything.
Click to expand...
Click to collapse
Typed up a long response then posted and ticket was expired lol. All I can think of right now is the phone still works, just can't see anything. Let the battery die, call the phone to see if it's dead or rings/vibrates. After it's dead plug her back up and see if she starts, can call again to check if it's in fact booted into Android. Maybe someone else can think of a better way, I take it you don't have the LED enabled for charging so that sucks. Like the previous poster said, it is not advised to let the battery drain 100%, one time however won't hurt, just don't do it repeatably. Hope you successfully get her up and running again I still have my pre-order Nexus 6, never a screen protector, just a Seidio Dilex Pro case and not a scratch on the beauty, someone needs to make a SD 835 phone with dual front facing speakers before I upgrade!
LaGgY_42o said:
Typed up a long response then posted and ticket was expired lol. All I can think of right now is the phone still works, just can't see anything. Let the battery die, call the phone to see if it's dead or rings/vibrates. After it's dead plug her back up and see if she starts, can call again to check if it's in fact booted into Android. Maybe someone else can think of a better way, I take it you don't have the LED enabled for charging so that sucks. Like the previous poster said, it is not advised to let the battery drain 100%, one time however won't hurt, just don't do it repeatably. Hope you successfully get her up and running again I still have my pre-order Nexus 6, never a screen protector, just a Seidio Dilex Pro case and not a scratch on the beauty, someone needs to make a SD 835 phone with dual front facing speakers before I upgrade!
Click to expand...
Click to collapse
Try iFixIt https://www.ifixit.com/Guide/Nexus+6+Display+Assembly+Replacement/36090
These fine people are in the town where I live and have very through tutorials. They are also involved in the political battles to allow user repair rights for everything you can imagine, and then some. :highfive:
So... teardown videos on YouTube fooled me and I thought that this phone is water-resistant. I washed it under tap water (multiple times, actually). After the last time, the screen stopped working, but the phone appears to be OK — even the touch clearly works. I've already disassembled the phone and cleaned the connectors with 95% alcohol, but the screen still doesn't work. Is buying a replacement screen and hoping for a cheap repair the smartest thing to do? After all, the motherboard can also be borked.
EDIT: the screen is completely black
BlueOner said:
So... teardown videos on YouTube fooled me and I thought that this phone is water-resistant. I washed it under tap water (multiple times, actually). After the last time, the screen stopped working, but the phone appears to be OK — even the touch clearly works. I've already disassembled the phone and cleaned the connectors with 95% alcohol, but the screen still doesn't work. Is buying a replacement screen and hoping for a cheap repair the smartest thing to do? After all, the motherboard can also be borked.
EDIT: the screen is completely black
Click to expand...
Click to collapse
I've replaced the screen after dropping the phone. Was only a small chip in the bottom corner, didn't look much at all, but the screen was completely dead. I was in a similar dilemma of wanting to be sure it was only the screen before spending about $100 on a screen. I booted into fastboot, then connected to a PC, then done the fastboot devices command, which returned a valid ID, so I knew the phone wasn't completely dead. Also connecting to the PC and booting the phone, the PC recognised the phone was connected, though without being able to unlock the phone I couldn't check anything else. That was enough for me to go ahead and order the screen. Now everything works fine.
Robbo.5000 said:
I've replaced the screen after dropping the phone. Was only a small chip in the bottom corner, didn't look much at all, but the screen was completely dead. I was in a similar dilemma of wanting to be sure it was only the screen before spending about $100 on a screen. I booted into fastboot, then connected to a PC, then done the fastboot devices command, which returned a valid ID, so I knew the phone wasn't completely dead. Also connecting to the PC and booting the phone, the PC recognised the phone was connected, though without being able to unlock the phone I couldn't check anything else. That was enough for me to go ahead and order the screen. Now everything works fine.
Click to expand...
Click to collapse
Thanks for sharing your experience! In my case, the phone clearly isn't dead, but I wonder whether some circuitry on the motherboard that's responsible for making the display work might be fried. Well... if that's the case, I can always sell the replacement screen after testing, but I'm not sure that someone will buy it for a good price.
Also... where did you get your screen from? On AliExpress, they are as cheap as $50, but most of the cheap ones are clearly some fake crap — TFT/IPS LCD, smaller than the original, fingerprint scanner not working... I guess I need to buy something more expensive. Have you noticed any difference between the original screen and your replacement?
BlueOner said:
Thanks for sharing your experience! In my case, the phone clearly isn't dead, but I wonder whether some circuitry on the motherboard that's responsible for making the display work might be fried. Well... if that's the case, I can always sell the replacement screen after testing, but I'm not sure that someone will buy it for a good price.
Also... where did you get your screen from? On AliExpress, they are as cheap as $50, but most of the cheap ones are clearly some fake crap — TFT/IPS LCD, smaller than the original, fingerprint scanner not working... I guess I need to buy something more expensive. Have you noticed any difference between the original screen and your replacement?
Click to expand...
Click to collapse
It was 4 months ago I got mine from AliExpress, at that time there wasn't any of these cheaper ones for sale. Looking at these cheaper ones they are TFT, though it's not always obvious in the description.
One seller is selling both TFT and OLED and are clearly labelled in the options. So from this assume that all cheaper ones are TFT.
It is a bit of a minefield. I doubt that any of the sellers have the actual original genuine screens. It took me a couple of days to go through all the listings and determine which one would most likely be good quality.
I eventually went for this one, which was slightly more expensive than most. Now though it appears to have gone up about $15 from when I bought it.
https://a.aliexpress.com/_d7OqLlE
At that time it had the best reviews, which appeared genuine. There were others with a higher review count, which appeared to be just as well reviewed, but reading the reviews you realise they are fake. Many reviews, supposedly from the USA, written in very poor pigeon English.
Also saw some stores with high review count, but then realised that most reviews are for completely different products (a common trick by some Ali sellers, completely change an existing listing so a new product looks like it's got high reviews)
The screen is good quality. It took about 3 weeks to arrive, but it was about 2 weeks after I damaged it before I ordered. So it was around 5 weeks after I last used the phone before installing it. After that time it's hard to judge if it is as good as the original. To look at and use the phone you wouldn't think it was a non original replacement, to me it seems to be as good as the original, without doing a side by side comparison. As far as an oleophobic coating, I couldn't say, it's had a screen protector since installing.
BlueOner said:
I washed it under tap water (multiple times, actually)
Click to expand...
Click to collapse
Umm. What? Even with IP rated phones you don't wash it with water. IP rating generally means that its good for accidental drops into water or for use in light rain. Why on earth would you wash it? Yes, I know jerryrig says there's some water ingress protection but it doesn't mean you should wash it with water. It just means you're good for use in light rain at best.
lambstone said:
Umm. What? Even with IP rated phones you don't wash it with water. IP rating generally means that its good for accidental drops into water or for use in light rain. Why on earth would you wash it? Yes, I know jerryrig says there's some water ingress protection but it doesn't mean you should wash it with water. It just means you're good for use in light rain at best.
Click to expand...
Click to collapse
Yes, I know. Very stupid. At least y'all can learn from it and avoid making the same mistake.
Robbo.5000 said:
The screen is good quality.
Click to expand...
Click to collapse
That's reassuring!
Robbo.5000 said:
it's hard to judge if it is as good as the original. To look at and use the phone you wouldn't think it was a non original replacement, to me it seems to be as good as the original, without doing a side by side comparison.
Click to expand...
Click to collapse
Well, I guess that even if it's a bit worse, replacing the screen is better (in my case) than dealing with an older/cheaper phone or throwing a nice sum of money on a phone in similar price range. I will report my experience after replacing the screen, maybe it will help someone. I'm definitely not going to find another guy with 9T (Pro) because of the coronavirus, but comparison with another high-quality AMOLED phone is another way to check the quality.
So... I wanted to order the screen, but when I checked whether the phone still works... it appeared dead. It charges, is visible in USB devices (but no fastboot etc.), the notification LED blinks, but that's all. It worked perfectly some time after the water damage occured, so I guess that the damage progressed. Yes, I didn't clean the phone thoroughly after disassembling it - I thought that the water probably evaporated anyway after using a heat gun, so, as I mentioned earlier, I cleaned only (easily accessible) connectors. Maybe it is something stupid (power button?), but it seems too good to be true. If I don't post another update, just assume that my phone died.
BlueOner said:
So... I wanted to order the screen, but when I checked whether the phone still works... it appeared dead. It charges, is visible in USB devices (but no fastboot etc.), the notification LED blinks, but that's all. It worked perfectly some time after the water damage occured, so I guess that the damage progressed. Yes, I didn't clean the phone thoroughly after disassembling it - I thought that the water probably evaporated anyway after using a heat gun, so, as I mentioned earlier, I cleaned only (easily accessible) connectors. Maybe it is something stupid (power button?), but it seems too good to be true. If I don't post another update, just assume that my phone died.
Click to expand...
Click to collapse
Press F in the comments section guys
My k20 pro Disable screen problem
Hi xda developers
After wetting the phone with a hand sanitizer and using the same wetness of the screen, I played the online game and put it in automatic game mode and rested for a while...
After waking up, I noticed that the phone was turned off, which was turned on by holding down the power button, but the screen is off...
Currently, only vibrators and notification lights work for the phone, and the phone is organized by a computer.
Also, the phone is charged and its sound can be heard while connecting it to the charger, and its sound can be heard in the same way to lock the screen.
Does anyone have an idea?
my phone just take s swim in the river yesterday, now its has no display but still on and even the touchscreen is working (i know is working cuz its register sound when i try to touch it everywhere). it have been dead first but then turn back on with everything work normal. but after about half hour, the screen suddnly dead.
after tear it my self i found where the water coming in, its from the 3.5mm jack. other holes have rubber protection but the jack has nothing. they even put water dammage indicator below the 3.5mm module....
i have try few method like clean the board with isoprofil alcohol but no avail. now im waiting my screeen replacement and will try to fixit my self.
IchsanWin32 said:
my phone just take s swim in the river yesterday, now its has no display but still on and even the touchscreen is working (i know is working cuz its register sound when i try to touch it everywhere). it have been dead first but then turn back on with everything work normal. but after about half hour, the screen suddnly dead.
after tear it my self i found where the water coming in, its from the 3.5mm jack. other holes have rubber protection but the jack has nothing. they even put water dammage indicator below the 3.5mm module....
i have try few method like clean the board with isoprofil alcohol but no avail. now im waiting my screeen replacement and will try to fixit my self.
Click to expand...
Click to collapse
Hello! Had exactly the same issue. Did it work to replace the screen?
My phone got into the sea (well the sea went into it), nothing happened for a while, and then it suddenly went black. Is working (like i can still use it as alarm lol) but the screen is not. Same as BlueOner, i'm afraid is not the screen itself but something in the mother board, so I would love to know if any of you were able to use it after replacing the screen or i will end up with the same issue.
Thanks!
saityro said:
Hello! Had exactly the same issue. Did it work to replace the screen?
My phone got into the sea (well the sea went into it), nothing happened for a while, and then it suddenly went black. Is working (like i can still use it as alarm lol) but the screen is not. Same as BlueOner, i'm afraid is not the screen itself but something in the mother board, so I would love to know if any of you were able to use it after replacing the screen or i will end up with the same issue.
Thanks!
Click to expand...
Click to collapse
It's toast. Don't even bother. The sea salt is hygroscopic, conductive (with moisture), corrosive and -everywhere- now.
It not a question of if it will fail only when.
Tap water is similar but not near as aggressive. The smallest amount of salt (sweat) can change that if it gets inside too. Even so if the device >didn't have it's battery pulled immediately<, then completely turn apart and cleaned with anhydrous isopropyl alcohol it won't fare much better in the long term most likely.
Any water internally can cause massive damage quickly. Or the signs of damage can take months to fully manifest themselves especially if the battery wasn't quickly pulled.
Salt water is fatal because it's residue doesn't easily rinse off as well as what was stated above.
This is why manufacturer warranties refuse to deal with water damage.
It's the gift that keeps giving...
Occasionally you can get lucky if you act fast
My Buds case fell into my coffee cup and immediately crash dived to the bottom like the sub in Das Boot. Cream and sugar too.
I pulled it apart and rinsed it will RO water then with anhydrous isopropyl alcohol in less then 3 minutes. Got as much as the isopropyl out as possible without compressed air and allowed it to dry in a warm sunny spot. Couldn't disconnect the Li battery as it was soldered or spot welded in. After about 2 days of drying it worked and other a year and a half later still is working.
I am still surprised...
Hi. I got water damage. The screen can be turn on but its not responding at all. I can press the power button, the screen lights up, as normal. I just couldn't unlocked it. It wont accept any touch. Also i tried calling from another phone, sound okay, also led notification working.
I havent try the charging port yet.
Anybody have similar experience? Can someone explain my problem? Should i order new screen replacement? Im just afraid its not screen problem.
harithzaim88 said:
Hi. I got water damage. The screen can be turn on but its not responding at all. I can press the power button, the screen lights up, as normal. I just couldn't unlocked it. It wont accept any touch. Also i tried calling from another phone, sound okay, also led notification working.
I havent try the charging port yet.
Anybody have similar experience? Can someone explain my problem? Should i order new screen replacement? Im just afraid its not screen problem.
Click to expand...
Click to collapse
Read my previous post.
You need to dry it out completely.
Hi everyone here, I hope everyone has a good day today. I've got my phone has been dead for quite a while now, the reason is it has the question mark during charging and I can't turn it off. At the first I thought it was the battery problem, I tried open it myself and replaced it with a new battery, however it got worse and it showed question mark battery and the question mark started blinking.
I haven't done checking to the repair shop due to busy with work. What do you guys think about the problem (might be the battery or one of the connector to the battery(?) and how much does it cost to fix it? Thanks in advance
Has it been exposed to moisture?
Is the charging port clean?
Is the battery degraded (less than 80% of its original capacity)?
Is there any swelling, case or display bulging?
If so replace battery asap.
Otherwise, this is a serious problem. Use known good brick and cable. See if that resolves it.
The next step is to replace the battery and check all connections. If that fails replace charging port PCB and/or jack (if it has a replaceable one). If all that fails... mobo failure
Well at the first, I dropped it, then the battery stuck at 50%, then I pressed the back area but still the same, however this phone is already out of warranty so I replaced the battery by myself.
shirobuhito said:
Well at the first, I dropped it, then the battery stuck at 50%, then I pressed the back area but still the same, however this phone is already out of warranty so I replaced the battery by myself.
Click to expand...
Click to collapse
If not the battery or loose connector... something was damaged in the drop. Always use a good case to prevent high G loading damage.
Hey! That means the phone isn't detecting the battery. As I saw you made a repair and you have an XL model, check the flex cable itself, especially where it folds, as it's very sensible and you could have bent it too much, breaking the cable.
I say that because I actually did that mistake, the cable doesn't usually come bent, so you need to bend it so it can fit, and when I did that I actually break it.
Hope this helps you!
#mcl said:
Hey! That means the phone isn't detecting the battery. As I saw you made a repair and you have an XL model, check the flex cable itself, especially where it folds, as it's very sensible and you could have bent it too much, breaking the cable.
I say that because I actually did that mistake, the cable doesn't usually come bent, so you need to bend it so it can fit, and when I did that I actually break it.
Hope this helps you!
Click to expand...
Click to collapse
I checked the flexible and it seems to be normal to me. I would not mind to buy another battery of it's the case. Thank you! Where did you buy the battery from?
shirobuhito said:
I checked the flexible and it seems to be normal to me. I would not mind to buy another battery of it's the case. Thank you! Where did you buy the battery from?
Click to expand...
Click to collapse
It's very hard to see using just the eye. Maybe if you have other phone try to zoom into the cable to check.
I usually buy this things from ebay. Just check it's a great seller and that the price isn't very cheap neither very expensive.