Hello,
since two month I've been having problems trying to get back to life an A6 2018 (SM-A600FN). It's not booting at all (just a blakc light blue screen). I can get in Downoad Mode though.
Prodyct Name: SM-A600FN
Current Binary: Samsung Official
Carrier_ID: ITV
Secure Download: Enabled
I've tried over 15 different firmwares (from 8.0 to 10) but they all FAIL on Odin "re-partition operation failed". I really don't know what else to do....it all started one mroning with a black screen and "invalid kernel lenght" text or something like that and since that day I'm not able to use this phone anymore.....any help please?
Thank you
Anyone??
Related
Hi,
I am trying to fix a broken SM-T710 which is stuck in a boot loop. I have been working on this for the last 24 hours and I have not gotten very far. I would be very grateful if someone could tell me what else I can try.
First, here are the symptoms:
Holding the power button while the tablet is not plugged in will cause it to show Samsung Galaxy Tab S2 powered by android, then it shuts off.
Plugging in the tablet starts a bootloop, flashing the same message as above, shutting off, and repeating
I have not been able to get the tablet into recovery mode
I can get the tablet into download mode (home+vol down+power)
In download mode it says:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-T710
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
Secure Download : Enabled
KNOX WARRANTY VOID: 1
RP SWREV: B:2 K:0 S:0
What I have tried so far is connecting the tablet into my PC and running Samsung Smart Switch. I did the emergency recovery and initialization within that software. After entering the model and serial numbers, it downloaded the software update and initialized it on the tablet, I could see the progress bar on the tablet during the initialization phase. It successfully resets the tablet but then the boot loop begins again.
I also tried downloading the firmware from Sammobile and flash in Odin. The file I have tried flashing is T710XXU2BPB1_T710XAR2BPB1_HOME.tar.md5. ODIN flashes the files and resets the tablet...back into a boot loop. I have not tried checking re-partition when I do this, as I do not know what to do about the PIT file
Is there anything else I should be trying? Thanks
Just flash using your original firmware.
This tablet came from eBay so I do not have any idea what the original firmware is. Everything I know about the tablet is in the first post. I assume that Samsung Smart Switch downloaded the original firmware since it required the model # and serial #. I am guessing that the tablet is from the USA but I do not even know that 100%
asty said:
This tablet came from eBay so I do not have any idea what the original firmware is. Everything I know about the tablet is in the first post. I assume that Samsung Smart Switch downloaded the original firmware since it required the model # and serial #. I am guessing that the tablet is from the USA but I do not even know that 100%
Click to expand...
Click to collapse
It's a hardware failure. Several others have had the same issue. Main board needed to be replaced.
I have the same issue here. It's a T715C which I bought in Singapore (distress purchase, rather than bargain hunting) and brought back to the UK.
Given that it's more than a year old, but a known fault, does anyone have any alternatives to taking it to the local recycling centre?
gswarbrick said:
I have the same issue here. It's a T715C which I bought in Singapore (distress purchase, rather than bargain hunting) and brought back to the UK.
Given that it's more than a year old, but a known fault, does anyone have any alternatives to taking it to the local recycling centre?
Click to expand...
Click to collapse
Try NAND erase while installing the firmware with odin.
I'd also try installing kitkat firmware if you can find it. Sometimes a downgrade fixes issues. You can then upgrade as normal.
Thanks. I'll have a Google and work out what that means. All my (many) Android devices have always been unrooted and only upgraded OTA!
gswarbrick said:
Thanks. I'll have a Google and work out what that means. All my (many) Android devices have always been unrooted and only upgraded OTA!
Click to expand...
Click to collapse
Hang on I had a bit of a brain freeze there. The earliest firmware will be Lollipop.
Try the Hong Kong firmware. Instructions to install are on the page.
https://updato.com/firmware-archive-select-model?record=E4B33EF21DCD11E6949E0CC47A44B7B2
Worth a try, I guess. Used Odin to flash the oldest Lollipop firmware I could find - with the NAND Erase All option - and it all seemed to work, but came back in the same state - six seconds of the boot splash screen followed by a second of black screen and repeat...
(Tried Marshmallow ROMS, too - no luck)
i have galaxy s2 8.0 (sm-t719Y)
after i root my tab,i want to unroot it
and after this my tab is getting error
i cant boot,and it say like this :
An error has occurred while updating the device software Use the Emergency recovery function in the Smart Switch PC software.
i have try flash it via odin mode,,i have download newest firmware for my tab (my tablet is indonesian version)
here the detail of firmware :
Model SM-T719Y
Model name Galaxy Tab S2
Country
Version Android 7.0
Changelist 12212928
Build date Wed, 06 Sep 2017 04:19:32 +0000
Security Patch Level 2017-08-01
Product code XID
PDA T719YDXU2BQI1
CSC T719YOLB2BQI1
status when downloading mode :
ODIN MODE(high speed)
PRODUCT NAME: SM- 719Y
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK : OFF
WARRANTY VOID: 0x01 (4)
QUALCOMM SECURE BOOT: Enabled(CSB)
RPSWREV: S1, T1, H1, R1, A2, P1
SECURE DOWNLOAD : ENABLE
when i flash this firmware with odin it always stuck at 80%
and it never finish
i also try to connect it to emergency software recover in smart switch menu,but it say my device is not supported
anybody know how to fix my tab
please be detail
thank before
Please help
TOTALREVOLUTION said:
Please help
Click to expand...
Click to collapse
Try flashing just the AP part.
Request of mixer_ path.xml for tab s2 t719y
TOTALREVOLUTION,can you share with me your mixer_path.xml?i can't seems to find it someway.i do really hope you can share it..anything just pm me or you can post it here..thanks mate
Ok try and do this as best as I can......
I bought a vwz S8 G950U used off someone from offer up was working fine when I bought it so when I got home I factory reseted to get all the users apps games etc off it and then it asked for a Google log in info (which I don't know) and I tryed to email the person but won't respond
So I tryed to install factory to binary to bypass it from what I been reading says I can do well I can get in factory binary now but now I cannot install oem stock firmware which I have downloaded 7.0 (what was on it ) says factory binary samsmobile and xda but every time odin3 gives me a fail message I have tryed odin3 3.127,3.13.1,3.12.3 and I think 1 more but every time I get a error....
So right now when I turn on the it his to factory binary mode and don't know of this helps but the battery won't charge past 80%....
What I'm asking if someone can be kind enough to help me out with this issue
P.S. I also tryed to instill Oreo 8.0 also but failed as well....
I can get any I go and post pics if that helps as well
Thank you in advance Jason A.KA. PpperoniRedd
trying to flash SM-G950U to stock and I keep getting SW Rev Check Fail fused 5 Binary 1
could anyone point me to what file i need to use i would appreciatw greatly as it has been a week and i have search on google and youtube and i can't figure it out
VZW S8 that had had FRP lock so i flashed to combination file and now I have only binary mode when the phone boot
when i go in binary mode and check under settings i have the followings
SM-G950U
Android 8.0
Secuirty Level Feb 1 2017
baseband: G950USQU5CRF1
Kernel 4.4.16-13344735
build NRD90M.FA70_G950USQU5ARG4
Download mode I have
Carrier : VZW
RPMB fuse blow
RPMB Provisioned
Current Binary: Samsung official
System Status : Official
FRP Lock : off
warranty void 0x0.
qualcom secure boot enabled
RP SWREV B5 (2.1.1.1.1) K4 S5
secure download enabled
G950usqu5crf1
I have the same problem, somebody already fix the problem?
does anyone know where to go after that error?, same error here if someone can point to the right direction will be appreciated
i have the same issue too, any idea guys?
0x0null said:
i have the same issue too, any idea guys?
Click to expand...
Click to collapse
5th digit back is boot loader bit number. This error is commonly from trying to flash with older firm Ware than on the devices
TheMadScientist said:
5th digit back is boot loader bit number. This error is commonly from trying to flash with older firm Ware than on the devices
Click to expand...
Click to collapse
I don't think so because i have 2 S8 with similar issues. I have the latest march firmware plus its confirmed bit5
Hello everyone,
A few days ago I bought a second hand note 8 (SM-N950F (Exynos)) The phone was working pefertly until I messed it up! What happpened was I tried updating my phone manually through odin. The reason I tried this was because my device is running 7.1.1 (nougat) and I wanted to update to 8 (oreo) and not 9 (pie) for a few reasons. So I downloaded 8.0 from sammobile. Now a few things could of gone wrong here. First of all in odin I tried to flash the other CSC not the HOME CSC I don't know if this is what caused the problem. Secondly when choosing the country of the firmware (united kingdom) I had two options because my device is unlocked XEU or BTU I didn't think it would matter and I think I orginally downloaded BTU but I am not sure. Anyways fast forwarding to the flashing process and I add all the files to odin BL, AP CP, CSC. Auto reboot and F. Reset Time were ticked and I clicked start. Along the top with the big boxes I got a green box with 'PASS' my phone rebooted to screen that says 'samsung galaxy note 8' but in the top corner it shows a message that says ' KERNEL REV. CHECK FAIL Device:3 BINARY:1'. If my device is plugged in wall or laptop it goes into a boot-loop and if it isn't connected I see the message once and then my phone turns off. I have tried both install 7.1.1 and 8.0 several times with both the XEU and BTU versions but no success. Sometimes a 'PASS' in the first box , sometimes a fail. When I'm in download mode I noticed with the info about my phone I have 'CARRIER_ID: XEU' which is in red (thought that would be worth mentioning). To add to my problems I think my battery may be getting low but im not sure. When I try to charge it goes into a bootloop and im not sure if its charging so for the time being it is off.
Any advice would be appreciated, I not had this phone yet and I love it! I also cannot afford another one. That's why I bought myself a second hand one.
Thanks :
ethlucas25 said:
Hello everyone,
A few days ago I bought a second hand note 8 (SM-N950F (Exynos)) The phone was working pefertly until I messed it up! What happpened was I tried updating my phone manually through odin. The reason I tried this was because my device is running 7.1.1 (nougat) and I wanted to update to 8 (oreo) and not 9 (pie) for a few reasons. So I downloaded 8.0 from sammobile. Now a few things could of gone wrong here. First of all in odin I tried to flash the other CSC not the HOME CSC I don't know if this is what caused the problem. Secondly when choosing the country of the firmware (united kingdom) I had two options because my device is unlocked XEU or BTU I didn't think it would matter and I think I orginally downloaded BTU but I am not sure. Anyways fast forwarding to the flashing process and I add all the files to odin BL, AP CP, CSC. Auto reboot and F. Reset Time were ticked and I clicked start. Along the top with the big boxes I got a green box with 'PASS' my phone rebooted to screen that says 'samsung galaxy note 8' but in the top corner it shows a message that says ' KERNEL REV. CHECK FAIL Device:3 BINARY:1'. If my device is plugged in wall or laptop it goes into a boot-loop and if it isn't connected I see the message once and then my phone turns off. I have tried both install 7.1.1 and 8.0 several times with both the XEU and BTU versions but no success. Sometimes a 'PASS' in the first box , sometimes a fail. When I'm in download mode I noticed with the info about my phone I have 'CARRIER_ID: XEU' which is in red (thought that would be worth mentioning). To add to my problems I think my battery may be getting low but im not sure. When I try to charge it goes into a bootloop and im not sure if its charging so for the time being it is off.
Any advice would be appreciated, I not had this phone yet and I love it! I also cannot afford another one. That's why I bought myself a second hand one.
Thanks :
Click to expand...
Click to collapse
EDIT: Everything is sorted now I had to upgrade to pie unfortunatly I had to use the CSC not HOME CSC and leave the CP empty
Dear ,
I have updated my Galaxy A71 to latest firmware A715FXXS9DWD1,
How can I flash previous version A715FXXU8DWB5
Both are Android 13 - One Ui 5.1
When I treid to flash through Odin I got an error
SW REV CHECK FAIL: fused 9 Binary 8
Please help.
After upfate to latest firmware, my screen color got changed. Black is not black it is like brownish, Also grey clor kind of greenish.
Please help guys to move back to previous.