I need to replace the screen on my Note 9. I see some screens available with no little extras. And I see some with adhesive pads and little tools. I have tools from other phone battery installs. How important are the adhesive pads? Can it be satisfactorily reassembled with the original adhesive?
To be honest you are better off replacing the entire front panel of your device. If the display is faulty or the glass is damaged. Unless you have a clean room and all the necessary tools to replace the glass on your device. Even then it is very difficult to replace the glass without damaging the AMOLED display.
^This^ and replace the battery too.
Yeah, I intend to do the whole screen and glass. I watched how-to's and R&Ring just the glass seems risky.
But how important are the new adhesive pads/strips?
Jwikoff99 said:
Yeah, I intend to do the whole screen and glass. I watched how-to's and R&Ring just the glass seems risky.
But how important are the new adhesive pads/strips?
Click to expand...
Click to collapse
You want to have them even if you don't need them. These phones are held together with them.
If you do it right the first time... you don't have to do a second time.
blackhawk said:
You want to have them even if you don't need them. These phones are held together with them.
If you do it right the first time... you don't have to do a second time.
Click to expand...
Click to collapse
That is true. But you have to make sure that you have the correct adhesive strips for putting together your device again. As if you use the wrong ones, your device may fall apart very easily.
iceepyon said:
That is true. But you have to make sure that you have the correct adhesive strips for putting together your device again. As if you use the wrong ones, your device may fall apart very easily.
Click to expand...
Click to collapse
They also come in different thicknesses. They have to be exact.
I repaired two of my Canon cams LCDs. Having the new strips made it go a lot easier and both jobs came out looking near perfect.
Speaking of batteries, does anyone know a good source for a new one? I got one that was supposed to be a new genuine Note 9 battery, but the capacity is even less then my original (3300 mAh vs 3500 mAh).
Jwikoff99 said:
Speaking of batteries, does anyone know a good source for a new one? I got one that was supposed to be a new genuine Note 9 battery, but the capacity is even less then my original (3300 mAh vs 3500 mAh).
Click to expand...
Click to collapse
The more recently it was manufactured the better given the quality is the same.
Li's age even when stored. They should be stored with half a full charge in a cool place.
Sure enough. What's a good source for a new one?
Are the batteries on Aliexpress reliable?
Related
Hello all!
I've been very pleased with my new Nexus so far, but yesterday I noticed the back cover was loose and and had a bit of a gap near the volume buttons. Some quick googling informed me this was a known issue, and is easily RMA'd. I have also discovered there are some very nice skins from Slickwraps and from Toast which can be used in place of the back cover. I find these to be very beautiful, and will most likely use one. Knowing this, is there any useful reason to send my phone in to be replaced? Has anyone discovered a flawed battery causing the cover to lift? If so, was it obvious before removing the cover?
I would be afraid that if I didn't get the phone replaced, it would leak if you ever got around water. I think I would send it back because if you ever decide to sell it you won't get much for a phone that doesn't have a tight fitting backup cover.
Sent from my Nexus 6 using Tapatalk
dalegg said:
I would be afraid that if I didn't get the phone replaced, it would leak if you ever got around water. I think I would send it back because if you ever decide to sell it you won't get much for a phone that doesn't have a tight fitting backup cover.
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
Those are both good points, but they are somewhat nullified by my plans. I'm going to be removing the back cover to use an aftermarket back. I will, of course, be fully responsible for protecting it from water, and for the damage if I don't. I tend to treat any device, water resistant or not, as if it were the Wicked Witch of the West and will melt upon contact with a drop of water. I also don't sell my old phones. They are way to useful to keep around for projects and such. I still have a couple of Blackberry Storms acting as desk clocks and a Galaxy Nexus doing tattle-tail duty for my home alarm system.
Basically what I'm looking for is any indication as to an actual malfunction being the cause of the back coming unstuck. As it stands, the loose back is a head start on getting it off for an aftermarket.
I say go for it as long as the new back cover fits tight. I am a snob about having a perfect phone.
Sent from my Nexus 6 using Tapatalk
Most the skins cover the back cover so need an intact backcover or have the same problem. Will see when remove back cover if it is battery related but then most likely can't RMA as you opened the device. It a catch 22 situation.
prdog1 said:
Most the skins cover the back cover so need an intact backcover or have the same problem. Will see when remove back cover if it is battery related but then most likely can't RMA as you opened the device. It a catch 22 situation.
Click to expand...
Click to collapse
I'm looking at the wooden covers. They're a bit thicker then the vinyl skins, and can sit flush with the frame when used without the back. They're rigid enough to do the job, though not advertised as backs, folk are reporting having success.
I am tempted to open it up and have a peek at the battery, but doing so would definitely void the warranty. That's why I was looking for any examples where a battery actually has gone bad. Though, it looks like the battery is pretty simple to replace anyway...
hawkjm73 said:
I'm looking at the wooden covers. They're a bit thicker then the vinyl skins, and can sit flush with the frame when used without the back. They're rigid enough to do the job, though not advertised as backs, folk are reporting having success.
I am tempted to open it up and have a peek at the battery, but doing so would definitely void the warranty. That's why I was looking for any examples where a battery actually has gone bad. Though, it looks like the battery is pretty simple to replace anyway...
Click to expand...
Click to collapse
Usually swells up in the middle and starts raising the back at the mid points.
prdog1 said:
Usually swells up in the middle and starts raising the back at the mid points.
Click to expand...
Click to collapse
Does it feel swollen? Can you tell by eye? The only ones I've witnessed having a dying battery had removable battery covers, like the Storm and the old Razr flip phones. My cover is only loose on one edge, and feels very firmly stuck the rest of the way around. The phone itself is functioning beautifully, not at all like the few I've seen the the grow-a-battery of death. They usually sputtered and gave up until I replaced the battery.
hawkjm73 said:
Does it feel swollen? Can you tell by eye? The only ones I've witnessed having a dying battery had removable battery covers, like the Storm and the old Razr flip phones. My cover is only loose on one edge, and feels very firmly stuck the rest of the way around. The phone itself is functioning beautifully, not at all like the few I've seen the the grow-a-battery of death. They usually sputtered and gave up until I replaced the battery.
Click to expand...
Click to collapse
If it's the battery will do the same. Will start acting up and then die. There is a thread somewhere in General I think with pics of expanding battery. Some just the backs come unglued. It is definitely a RMA situation anyway.
So I had an incident with my beloved Z3c (D5803) and now I find myself in need to repair it. I don't really want to share the details of such incident and to be honest they are not that important. What's important is that I decided to replace the whole LCD/digitizer assembly.
What would you recommend in terms of better achievable waterproofing, just the LCD/digitizer with the adhesive tape or the whole midframe with the display attached already? The one with the midframe attached already costs about 33% more, but I'm willing to pay the premium if that means that the phone will still be waterproof after the repair.
The same question goes for the back cover, should I just buy new adhesive and re-use the current one (which is in almost mint condition) or just buy a new cover with the tape pre-attached?
And lastly, I'm planning on buying this stuff on eBay, and I'd like to know what you think about these listings. I must note that I have a 20% site wide discount coupon, so if you recommend another site because it's cheaper keep that in mind.
With midframe
Without
Just yesterday I replaced my back panel with one found on witrigs, OEM I believe. Because it was already cracked it came off really easy and I didn't need to preheat the adhesive. There was very little residue which I removed and after that plopped the new one on. The new glass back panel came with adhesive already on it, I would advice that. The whole process was very easy and took about 10 minutes. Look around for repair/disassembly tutorials and good luck!
XclusionNL said:
Just yesterday I replaced my back panel with one found on witrigs, OEM I believe. Because it was already cracked it came off really easy and I didn't need to preheat the adhesive. There was very little residue which I removed and after that plopped the new one on. The new glass back panel came with adhesive already on it, I would advice that. The whole process was very easy and took about 10 minutes. Look around for repair/disassembly tutorials and good luck!
Click to expand...
Click to collapse
Thank you for your advice, I've already seen a couple of disassembly guides and I think I've got a good idea on how to fix this myself (or in the worst case scenario I could go to one of the hundreds of repair shops in the downtown, here in Mexico City, and pay the guy a couple of bucks to install the parts I'm going to buy).
What I'm most worried about is the waterproofing; have you tested your phone in this regard? I still don't know which part to buy, the whole assembly or just the LCD/digitizer.
As for the back cover... I might as well buy both the adhesive and the back cover, it would be like 7-8 bucks for both.
jhonyrod said:
Thank you for your advice, I've already seen a couple of disassembly guides and I think I've got a good idea on how to fix this myself (or in the worst case scenario I could go to one of the hundreds of repair shops in the downtown, here in Mexico City, and pay the guy a couple of bucks to install the parts I'm going to buy).
What I'm most worried about is the waterproofing; have you tested your phone in this regard? I still don't know which part to buy, the whole assembly or just the LCD/digitizer.
As for the back cover... I might as well buy both the adhesive and the back cover, it would be like 7-8 bucks for both.
Click to expand...
Click to collapse
I have not tested if it is water proof because I am not sure it will survive the test As for your second question: if the primary concern is waterproofness you might as well go for the whole assembly, that seems saver to me
XclusionNL said:
I have not tested if it is water proof because I am not sure it will survive the test As for your second question: if the primary concern is waterproofness you might as well go for the whole assembly, that seems saver to me
Click to expand...
Click to collapse
Yeah, I bought the full assembly, as well as 2 sets of adhesives and a back cover. I thought that I might be able to re-stick my current display (the only issue it has is a couple of dead lines in the bottom left edge; like 10 by 5 lines) and have it as a back up or maybe even sell it as scrap.
BTW, you can test if your phone is air tight in the service menu, if it is air tight it most likely is water tight as well. Dial #*#*SERVICE*#* #, then tests and then peressure sensor, squeeze the phone and you should see the pressure rise.
Mine, when brand new, rose a bit and then it slowly decreased... Now with the nature of the damage of the display I think that it wasn't entirely waterproof to begin with. Who knows? Maybe after the repair it will end up 'more' waterproof than before.
I just used that service menu, it shows me about 1020 millibar and goes slightly up when I firmly press the phone, so.... this means my repair was a success as far as air-tightness goes?
If it stays up for as long as you press it I reckon it still is waterproof (but then again, don't go swim with it based on this, even Sony doesn't recommend doing this anymore). If it goes down maybe it has a leak, but as I've said before, mine had such a leak since I bought it, so go figure.
I have read lots of threads and comments on the Internet regarding screen cracking on the z3c but most are dating back to early 2015.
As I am now considering buying a Z3C does anyone know if improvements have been made by Sony to address these issues for the 2016 models?
Thanks for any comments.
Nothing has changed. On the bright side, replacing said-glass is very cheap and easy to do. On the minus-side. Say bye-bye to any form of water-resistance. This long with the Z3C: I've grown to accept this phone won't be water-resistant unless I use a case because the seals and IP-68 rating is only for fresh-water and the rating completely depends on the ability of flap-seals and sealant of the back cover to to do its job. I hope I can convince you to disregard water-resistance factor in your purchase. Notably because Sony won't cover any repairs if the damage is a result of water-damage(personal experience). That way, you can swap back glass covers as you please. They go for like $2.
My z3c screens right top corner today unglued. Lasted for about 8 months since purchase, without case, without any water interference. Still under warranty, sending it for repair.
alpha-niner64 said:
Nothing has changed. On the bright side, replacing said-glass is very cheap and easy to do. On the minus-side. Say bye-bye to any form of water-resistance. This long with the Z3C: I've grown to accept this phone won't be water-resistant unless I use a case because the seals and IP-68 rating is only for fresh-water and the rating completely depends on the ability of flap-seals and sealant of the back cover to to do its job. I hope I can convince you to disregard water-resistance factor in your purchase. Notably because Sony won't cover any repairs if the damage is a result of water-damage(personal experience). That way, you can swap back glass covers as you please. They go for like $2.
Click to expand...
Click to collapse
Thanks for the reply, if I understand you correctly replacing the back glass is not a big issue and is cheap, but what about the front screen? I did have a quick search around the net and it looks quite complicated and expensive to replace the front one.
Have you done the front one yourself?
Thanks.
vilx01 said:
My z3c screens right top corner today unglued. Lasted for about 8 months since purchase, without case, without any water interference. Still under warranty, sending it for repair.
Click to expand...
Click to collapse
Yep, mine has unglued as well, after 7 months of usage (bought it brand new), I am sending it for repair also. When my warranty expires, I will replace case on my own, because I have black one, and I want black screen + white case
bmg777 said:
Thanks for the reply, if I understand you correctly replacing the back glass is not a big issue and is cheap, but what about the front screen? I did have a quick search around the net and it looks quite complicated and expensive to replace the front one.
Have you done the front one yourself?
Thanks.
Click to expand...
Click to collapse
I service my own phones often enough to kind of say that replacing your own front screen is easy to do if you're starting out with this phoneYou take out the front-screen the same way you take apart the back screen.. As long as your motherboard components are in good condition like the USB Port, antenna, SIM/MicroSD slots, and the battery(cause this is glued very well to the motheboard), nearly everything on the Z3 Compact is expendable and easily replaceable.
alpha-niner64 said:
I service my own phones often enough to kind of say that replacing your own front screen is easy to do if you're starting out with this phoneYou take out the front-screen the same way you take apart the back screen.. As long as your motherboard components are in good condition like the USB Port, antenna, SIM/MicroSD slots, and the battery(cause this is glued very well to the motheboard), nearly everything on the Z3 Compact is expendable and easily replaceable.
Click to expand...
Click to collapse
I've been using Z3C (15W33) since early september and this phone has really rough life. I mean working in very hard conditions (very cold outside > pretty warm inside the house) and I never really cared about it even when I know there are problems with the glass. Also I have a custom s-line case and that's the only protection... I dropped the phone twice or three times...
but it's still running pretty nice and there are no signs of any damage, the glass is more than OK
I just purchased one of these off Swappa for 60 bucks. I got too excited, I couldn't control myself, haha. The glass is cracked, and I'm contemplating trying to remedy that depending on potential usability. I remember sometime late last year that there were a whole bunch of displays for the prototype with the "Not for resale; property of Motorola" sold off on eBay; they're long gone by now since people bought them up thinking they'd work on the standard Nexus. But they discovered the display connectors are in slightly different places than their production unit; meaning they're not interchangeable and couldn't be used. If I can't find one of these displays, I'm expecting that I could just remove the glass and replace it with a standard one, but I'm HORRIFIED of potentially damaging the display itself since they're so fragile. It's horrifying because if it's damanged, that's it. It won't accept a production panel.
So I guess what I'm wanting to know is if anybody happens to know where I can get a hold of a replacement display for this phone at a decent price. As mentioned, the display works fine, but the glass is cracked. I'm not expecting to be able to use it since these phones seem to be finicky, so I'm not interested in dumping any huge amount of money into it; I'm just exploring my options on restoring it. If I can happen to use it for personal use, that'd be great; but i'm not holding my breath haha.
Slightly OT, but if you have a prototype model, I wonder if it also has the internal connector for the fingerprint reader. That would be interesting to find out.
Screens pls, btw i found 1 long time ago in eBay, Google buy then back for mich money
Gesendet von meinem PHICOMM ENERGY 3+ mit Tapatalk
illitero said:
I just purchased one of these off Swappa for 60 bucks. I got too excited, I couldn't control myself, haha. The glass is cracked, and I'm contemplating trying to remedy that depending on potential usability. I remember sometime late last year that there were a whole bunch of displays for the prototype with the "Not for resale; property of Motorola" sold off on eBay; they're long gone by now since people bought them up thinking they'd work on the standard Nexus. But they discovered the display connectors are in slightly different places than their production unit; meaning they're not interchangeable and couldn't be used. If I can't find one of these displays, I'm expecting that I could just remove the glass and replace it with a standard one, but I'm HORRIFIED of potentially damaging the display itself since they're so fragile. It's horrifying because if it's damanged, that's it. It won't accept a production panel.
So I guess what I'm wanting to know is if anybody happens to know where I can get a hold of a replacement display for this phone at a decent price. As mentioned, the display works fine, but the glass is cracked. I'm not expecting to be able to use it since these phones seem to be finicky, so I'm not interested in dumping any huge amount of money into it; I'm just exploring my options on restoring it. If I can happen to use it for personal use, that'd be great; but i'm not holding my breath haha.
Click to expand...
Click to collapse
i use these over screen protectors. the are big enough to fit phone screens and do a nice job with glare from light while keeping the display to color. they scuff up (like all do) but the......gel? like texture will smooth back out instead of removing the visibility. there are 2 draw backs....they add a soft prism texture due to the quality on the glue involved as well as soft dots from the high quality adherence. the more it warms the softer the dots appear. all said and done, i have put this laminate on cracked screens with a fair solution. no shelling out for the lcd as well as not risking a lcd for a $25 dollar piece of glass
DontStopDev said:
i use these over screen protectors. the are big enough to fit phone screens and do a nice job with glare from light while keeping the display to color. they scuff up (like all do) but the......gel? like texture will smooth back out instead of removing the visibility. there are 2 draw backs....they add a soft prism texture due to the quality on the glue involved as well as soft dots from the high quality adherence. the more it warms the softer the dots appear. all said and done, i have put this laminate on cracked screens with a fair solution. no shelling out for the lcd as well as not risking a lcd for a $25 dollar piece of glass
Click to expand...
Click to collapse
I definitely appreciate the suggestion, but I'm specifically looking for input on where I can get replacement screens. I don't mind cracks in screens personally (swappa boneyard represeeeeent! lolol), but with my last N6 screen cracking from compromised glass up top, I'm paranoid of any use doing the same to the prototype display. I want to either use it or sell it, and as long as the glass is broken I can't really do either :crying:
Finding a prototype display is going to be virtually impossible due to ridiculously limited quantities, and replacing it with a production model version - if that's even doable - would kill any value the prototype might still have. If you're looking to use it, you're probably going to have to fish for a production screen and hope Motorola didn't make any changes between the prototype and production model.
BlockOfDynamite said:
Slightly OT, but if you have a prototype model, I wonder if it also has the internal connector for the fingerprint reader. That would be interesting to find out.
Click to expand...
Click to collapse
I'm asking myself exactly the same thing..
Then, do it have it or not ??
If the touchscreen isn't broken, you can change the gorilla glass only, by yourself. It must be standart size. (using heatgun and being tricky)
If it is, you can go to Shenzen in China, or maybe try to adapt the connector (they might have taken the same components but in a small different way, connector lenght/position)
mesco38 said:
I'm asking myself exactly the same thing..
Then, do it have it or not ??
If the touchscreen isn't broken, you can change the gorilla glass only, by yourself. It must be standart size. (using heatgun and being tricky)
If it is, you can go to Shenzen in China, or maybe try to adapt the connector (they might have taken the same components but in a small different way, connector lenght/position)
Click to expand...
Click to collapse
You're better give the device to a repair technician with good skills. I'm a technician and the process to separate the glass from displays is not diy . It's really hard to be done correctly, and with an oled screen is even harder
illitero said:
I just purchased one of these off Swappa for 60 bucks. I got too excited, I couldn't control myself, haha. The glass is cracked, and I'm contemplating trying to remedy that depending on potential usability. I remember sometime late last year that there were a whole bunch of displays for the prototype with the "Not for resale; property of Motorola" sold off on eBay; they're long gone by now since people bought them up thinking they'd work on the standard Nexus. But they discovered the display connectors are in slightly different places than their production unit; meaning they're not interchangeable and couldn't be used. If I can't find one of these displays, I'm expecting that I could just remove the glass and replace it with a standard one, but I'm HORRIFIED of potentially damaging the display itself since they're so fragile. It's horrifying because if it's damanged, that's it. It won't accept a production panel.
So I guess what I'm wanting to know is if anybody happens to know where I can get a hold of a replacement display for this phone at a decent price. As mentioned, the display works fine, but the glass is cracked. I'm not expecting to be able to use it since these phones seem to be finicky, so I'm not interested in dumping any huge amount of money into it; I'm just exploring my options on restoring it. If I can happen to use it for personal use, that'd be great; but i'm not holding my breath haha.
Click to expand...
Click to collapse
Have you seen any more of these around?
I'd be interested in a Prototype Nexus 6 in any shape.
Heck, if you're interested in selling yours, I'd be interested (just PM me if).
Axel85 said:
You're better give the device to a repair technician with good skills. I'm a technician and the process to separate the glass from displays is not diy . It's really hard to be done correctly, and with an oled screen is even harder
Click to expand...
Click to collapse
Didn't say it will be easy
I don't know him, he may be more minutious than you, idk. Just giving a possibility, he will judge if he's able to do it himself..
mesco38 said:
Didn't say it will be easy
I don't know him, he may be more minutious than you, idk. Just giving a possibility, he will judge if he's able to do it himself..
Click to expand...
Click to collapse
I replied you and him only to tell that it's really hard , only to let you know and to let him know before he tries to order the glass,try to separate that from display and make it worse . Oled displays goes completely black if broken ,instead of LCD that stay alive .
I know procuring one is next to impossible. The reason I asked is because I had seen a large batch of them sold on eBay sometime last year. So people expecting them to work for their regular Nexus phones (they don't; ribbons are slightly different) bought them and ended up not being able to use them. A shot in the dark for sure, haha. Otherwise I have replacement production glass, LOCA, and a plate and wire to do the job properly, it's just as all stated in the original post: failure is an absolute game over. A screen with cracked glass is much more functional than a dead screen with good glass, you know?
Hi everyone,
After 1 and half years my screen has broke yesterday, it fell a stupid fall on charger and broke from top speaker side, even though screen protector is on and case is on. It is what it is.
I am not planning to replace this device, I'll fix screen, so any recommendations? Anyone experienced screen replacement? Did you send it back to supplier or you replaced it your self?
Should I get screen replacement with frame or just screen and I keep my frame?( Not a scratch on my frame). Any place you recommend to get new screen?
Should I use T7000 glue or is there something better?
Any advises to consider while fixing it?
Any comment is appreciated.
My first question would be, have you ever done a screen replacement before? Because if you haven't then I'll recommend taking it to a reputable repair shop nearby considering you are not planning to buy another phone. Also just get the screen fixed no point in changing the frame as you said it's in good shape. But if you really wanna experience the bliss and accomplishment that is fixing your own device then always follow IFixIt guides and before opening it up or ordering parts read about your device's repairability. Also asking your friends and other people around you for a good repair shop would be a good idea.
Confused Gamer said:
My first question would be, have you ever done a screen replacement before? Because if you haven't then I'll recommend taking it to a reputable repair shop nearby considering you are not planning to buy another phone. Also just get the screen fixed no point in changing the frame as you said it's in good shape. But if you really wanna experience the bliss and accomplishment that is fixing your own device then always follow IFixIt guides and before opening it up or ordering parts read about your device's repairability. Also asking your friends and other people around you for a good repair shop would be a good idea.
Click to expand...
Click to collapse
Hi,
regarding your first question, not for a mobile phone, because i know how to take care of my stuff, except this time (sigh). but of course i've done it for a laptop of my friend, and many many many electrical fixes. so do not worry about me doing it my self as it is my thing to do things my self.
regarding asking about the frame, i am asking this just to see if any one experienced replacing it without frame and how well was it sealed compared to pre and properly sealed. got my point?
Thanks for your valuable advice,
hassanaliyeh said:
Hi,
regarding your first question, not for a mobile phone, because i know how to take care of my stuff, except this time (sigh). but of course i've done it for a laptop of my friend, and many many many electrical fixes. so do not worry about me doing it my self as it is my thing to do things my self.
regarding asking about the frame, i am asking this just to see if any one experienced replacing it without frame and how well was it sealed compared to pre and properly sealed. got my point?
Thanks for your valuable advice,
Click to expand...
Click to collapse
Okay, this means that it'll be easy for you to repair your device, as for the frame I think you can buy a silicone seal as well and comes in a plastic case so it'll be easy to line it up, even If it doesn't you can buy sealing glue and do it yourself, it'll definitely be much cheaper than getting the whole frame. I do get your point now.
Confused Gamer said:
Okay, this means that it'll be easy for you to repair your device, as for the frame I think you can buy a silicone seal as well and comes in a plastic case so it'll be easy to line it up, even If it doesn't you can buy sealing glue and do it yourself, it'll definitely be much cheaper than getting the whole frame. I do get your point now.
Click to expand...
Click to collapse
with frame it is just 35$ (AUD) more, around 20$ (USD). not much to save
hassanaliyeh said:
with frame it is just 35$ (AUD) more, around 20$ (USD). not much to save
Click to expand...
Click to collapse
My question now is that the MI 11U has an AMOLED display that is really good like HDR10+, 1Billion colors, Dolby vision and, 1700 nits peak brightness, where did you find a screen this inexpensive for $20 aud?
Confused Gamer said:
My question now is that the MI 11U has an AMOLED display that is really good like HDR10+, 1Billion colors, Dolby vision and, 1700 nits peak brightness, where did you find a screen this inexpensive for $20 aud?
Click to expand...
Click to collapse
The frame is additional 20$..... Not the screen
hassanaliyeh said:
The frame is additional 20$..... Not the screen
Click to expand...
Click to collapse
Oh okay, I thought it was weird, I hope you're able to fix your device and 20-35 would certainly be worth it if it did make the repair convenient for you.