I want to repair a G5s that is missing a few screws too. Does anybody know the type of these screws, so I can order some?
Related
Hi,
This is by far the most hi-tech question on the board... ;-)
I've lost the stupid little rubber cap that used to cover the antenna port. Cingular and Siemens are unable/unwilling to assist. Has anybody found an alternate source for replacements?
Thanks in advance!
Annoying little rubber piece
You the same exact thing happen to me. I ended up taking it from the non working display model at the sprint store. But then I lost it again. So if anybody knows, please let me know
Hum... I tried that with the styalist only to find that it was glued! Oh no let me correct that a friend of mine told me that he...
Try using the plastic bit on the non-writing end of a Bic stick ballpoint pen; it's about the right size & shape.
i-mate said they'd replace mine. Maybe I can get a few extras, too.
TheLastOne
You must be on great drugs! were do you get them from? LOL
i recieved a tilt i had purchased on ebay and it is pretty bad. i know it needs a flex cable after SEARCHING for it...however i cannot find the answer to this. i am looking into purchasing a full housing off ebay from forceviewer_uk however its unclear if i need the sliding mechanism to go with it as i just want to replace everything except the board and lcd. do i need the sliding mechanism, is it a good idea to replace it, or what. any help is very appreciated. thanks
Can Anyone tell me where to get replacement screws or the name and type of them. i been looking for hours and still no luck. Thanks
Now that the wood back plates are popping up on Ebay, I'm wondering how difficult it would be to change out the stock plate with a wood one. It looks like there is no adhesive, flash or camera lens in these new backs, so I'm curious how hard it would be to migrate everything over. Does anyone have any experience doing this and want to give me some pointers? Also, if you don't reuse the adhesive, what product would you use in its place? Thanks in advance!
There is a thread in the accessories forum that might be of use to you in regards to back cover replacements.
Sent from my XT1060 using Tapatalk
Pr0f_Farnsw0rth said:
Now that the wood back plates are popping up on Ebay, I'm wondering how difficult it would be to change out the stock plate with a wood one. It looks like there is no adhesive, flash or camera lens in these new backs, so I'm curious how hard it would be to migrate everything over. Does anyone have any experience doing this and want to give me some pointers? Also, if you don't reuse the adhesive, what product would you use in its place? Thanks in advance!
Click to expand...
Click to collapse
Begin your search here:
http://forum.xda-developers.com/showthread.php?t=2500086
On the G+ moto x community, someone posted pics of a swap that he did.
There's a you tube video of it. Try that Google thing. Instant answers.....sometimes.
Sent from my Moto X cellular telephone...
kj2112 said:
There's a you tube video of it. Try that Google thing. Instant answers.....sometimes.
Sent from my Moto X cellular telephone...
Click to expand...
Click to collapse
To be fair, I did that Google thing... Found myself here
I'll see myself out now...
ordered a digitizer with bezel and all that stuff pre assembled from some phone seller in china (only one on the net selling the assembly). the chassis is different tho. I cant fit the black box that the signal wire attaches to in the new chassis.
anyone else run into this problem. do I need to post a pick to help you guys help me?
bump
montrese04 said:
ordered a digitizer with bezel and all that stuff pre assembled from some phone seller in china (only one on the net selling the assembly). the chassis is different tho. I cant fit the black box that the signal wire attaches to in the new chassis.
anyone else run into this problem. do I need to post a pick to help you guys help me?
Click to expand...
Click to collapse
Are you sure you didn't order parts for the Z1? The Z1 and the Z1s are different in size etc