Database Develop

galaxy s plus bluetooth bootloop

Am using cm10 beta7 but am getting bootloop after turning on bluetooth..the problem is
1)i turn on bluetooth
2)phone goes into reboot loop but doesn't boot up
3)i pull out battery and put it back and turn on phone
4)phone boots with bluetooth on and bluetooth works fine
please note that i did a clean odin flash of official gb and then installed it with all cache data dalvik cache wipes... bluetooth works well with stock gb..so hardware no fault..
please anyone help!! i've also seen other ppl complaining about this problem..even in cm9..ANY FIX??

pradeepjoshua said:
Am using cm10 beta7 but am getting bootloop after turning on bluetooth..the problem is
1)i turn on bluetooth
2)phone goes into reboot loop but doesn't boot up
3)i pull out battery and put it back and turn on phone
4)phone boots with bluetooth on and bluetooth works fine
please note that i did a clean odin flash of official gb and then installed it with all cache data dalvik cache wipes... bluetooth works well with stock gb..so hardware no fault..
please anyone help!! i've also seen other ppl complaining about this problem..even in cm9..ANY FIX??
Click to expand...
Click to collapse
Hello, I have the same problem, and now in its variant :
- the sgs reboots when activating bluetooth, with bluetooth off
- it looks like no way to activate bluetooth without provoking smartphone reboot
Does cm update fix this problem ?
Other suggestion ?
Thanks for reading

z2x said:
Hello, I have the same problem, and now in its variant :
- the sgs reboots when activating bluetooth, with bluetooth off
- it looks like no way to activate bluetooth without provoking smartphone reboot
Does cm update fix this problem ?
Other suggestion ?
Thanks for reading
Click to expand...
Click to collapse
You should ask this problem in the development forum of your CM version and/or kernel version. They may be able to help you more e.g. by asking for specific logcat data from the time of your reboot.
Other than that, I'd say there is something fishy with your kernel. Did you try to use stock kernels? Or the latest CM10 of Ivendor? People are having less and less problems with that.

N920C - Kernel is not seandroid enforcing

Hello All,
As the topic says i tried to root my Note 5 device using "Noble_Kernel_Auto-Root_N920T_v0.1_Rebuid3" and Root Checker Basic says "Root access is properly installed on this device" ...
However it reboots itself from time to time and i see the red "Kernel is not seandroid enforcing" warning.
I rooted it once more and during root i saw the red warning there as well...
Did i do sth wrong or do i need to wait more for a proper root for my model.
Also i do need the stock software...
Your helps are highly appreciated,
Thanks in advance
Theo
I solved this problem by following the items below (follow the order);
1) load stock firmware (download from sammobile use odin),
2) reboot and check your device is normal again,
3) backup your phone,
4) root once more,
5) reboot and see the red writing in upper left corner,
6) turn off and enter into recovery mode,
7) wipe/clear cache,
8) reboot,
9) enjoy
P.S. : From what i have read "Kernel is not seandroid enforcing" simply shows "your warranty is now void"
As i write these my phone shows it while every reboot but the reboot problem seems solved (none for a couple of days)
Hope it helps you too

That was normal on note 3. My 5 isn't rooted, but sounds like the same thing.

abax44 said:
That was normal on note 3. My 5 isn't rooted, but sounds like the same thing.
Click to expand...
Click to collapse
Hello,
But my problem is the device reboots itself randomly. I also do not have a backup.. (So maybe i need a stock software to load again)

Alansal said:
Hello,
But my problem is the device reboots itself randomly. I also do not have a backup.. (So maybe i need a stock software to load again)
Click to expand...
Click to collapse
it's a known issue with some kernels for the Note5; you might see if arter97's kernel works for the 920C. i've been using his kernel since he released it on my 920T and haven't had any rebooting issues. i believe the message Kernel is not seandroid enforcing is common on Note 4/5 rooted devices that don't use a Samsung sourced kernel. arter97's kernel is based on Samsung sources so it doesn't show that message at boot-up. hope this is helpful for you.

got the same problem, please help!

pc999 said:
got the same problem, please help!
Click to expand...
Click to collapse
I solved this problem by following the items below (follow the order);
1) load stock firmware (download from sammobile use odin),
2) reboot and check your device is normal again,
3) backup your phone,
4) root once more,
5) reboot and see the red writing in upper left corner,
6) turn off and enter into recovery mode,
7) wipe/clear cache,
8) reboot,
9) enjoy
P.S. : From what i have read "Kernel is not seandroid enforcing" simply shows "your warranty is now void"
As i write these my phone shows it while every reboot but the reboot problem seems solved (none for a couple of days)
Hope it helps you too
Cheers mate

Is this solution tested on Sm-n920t note 5? If so, does it work? Is there any different steps you need to take?
Thanks

dohcvtec said:
Is this solution tested on Sm-n920t note 5? If so, does it work? Is there any different steps you need to take?
Thanks
Click to expand...
Click to collapse
I personally don't own a "T" model so i could not try.....

Alansal said:
I personally don't own a "T" model so i could not try.....
Click to expand...
Click to collapse
Okay. Thank you for trying to help. If anyone has ideas, let me know. Thanks in advance!

Stuck on Download Mode

Hello ,
I have Korean version N950N. I flashed twrp and then i rooted to phone. Today i decided to flash stock rom with Odin. When i started the flash approx %80 odin was stop and i wait more than 1 hour then i pulled out the cable. Now phone give some error (its Korean language ) and i can access to download mode. I tried with 2 different rom but after %80 odin stop again. Now i can not use my phone even i can not turn off always giving error. How can i solve this problem? Please help me. Thank you.

bahadir70 said:
Hello ,
I have Korean version N950N. I flashed twrp and then i rooted to phone. Today i decided to flash stock rom with Odin. When i started the flash approx %80 odin was stop and i wait more than 1 hour then i pulled out the cable. Now phone give some error (its Korean language ) and i can access to download mode. I tried with 2 different rom but after %80 odin stop again. Now i can not use my phone even i can not turn off always giving error. How can i solve this problem? Please help me. Thank you.
Click to expand...
Click to collapse
Have you tried the smart switch emergency recovery option?

BluePhnx said:
Have you tried the smart switch emergency recovery option?
Click to expand...
Click to collapse
When i connected to smart switch its also said this phone not supported...

Can you go in to recovery mode and factory reset?

bahadir70 said:
When i connected to smart switch its also said this phone not supported...
Click to expand...
Click to collapse
Can you flash TWRP and get into recovery to wipe system or flash a custom Rom?

BluePhnx said:
Have you tried the smart switch emergency recovery option?
Click to expand...
Click to collapse
android-incredible said:
Can you go in to recovery mode and factory reset?
Click to expand...
Click to collapse
I can not most probably , also now battery is off and i forget my cable at office Tomorrow i will try one more time. But o with phone i can access only download mode, with smart switch giving error as well.

Well ,i solved the problem. I downloaded last version of stock rom and i changed odin as well. Now phone is working. For the S-health i downloaded old version and after that i updated with play store then S-health working properly.

bahadir70 said:
Well ,i solved the problem. I downloaded last version of stock rom and i changed odin as well. Now phone is working. For the S-health i downloaded old version and after that i updated with play store then S-health working properly.
Click to expand...
Click to collapse
Good to hear . Now leave it alone
Sent from my SM-N950U using Tapatalk

android-incredible said:
Can you go in to recovery mode and factory reset?
Click to expand...
Click to collapse
I Hi am wondering if you could help with my Galaxy Note 8
I am able to install the firmware using ODIN without any errors on download mode but after ODIN is finished the phone turns off and does not boot.
I have taken the phone to a repair shop as well and they have confirmed that there is no hardware issues,
My model number is SM-950F , basically stuck on download mode
No luck turning the phone on recovery mode only can use download mode and i have tried the same files with the Nand erase all, the same thing .. Odin installs all the files without any errors but does not boot up after installation is finished.
The service shop said they checked components on the motherboard and there is no damage or no IC has been damaged.
What do you suggest i do next?

Note 9 bootloop out of nowhere!!

So let me give you a little background first. I was at my brother's house recording him dunk in superslowmo. All of a sudden, my phone freezes. After about 2-5 mins I decide To hold power +volume down and the phone goes black and goes to the "Samsung Galaxy note 9 secured by knox" screen and does a infinite reboot to that screen. The phone will not go into recovery mode BUT will go into Download Mode. I tried letting the phone completely drain and then trying it with no success.
I do have AT&T protection on my device but the only thing they will do is replace it which I'm trying to avoid being that I have pictures I want to extract from the phone.
So to my question(s)
1) if I flash latest version of firmware from sammombile will I lose my pictures? (Trying to avoid loss of pics)
2) can I use a MacBook to do the reflashing or does it have to be windows?
Please and thx to all that respond!!!

Once in download mode hold volume down and power to see if phone boots up. If you reflash with Odin use home_csc so it does not wipe your data. If you do get to recovery do not do a wipe, everything you have saved to phone storage will be gone. See if you can get to device storage by connecting to computer once your in download mode or recovery. If so just move all important files to computer then you can use Odin to flash firmware.
Sent from my SM-N975U using Tapatalk

Bicka0701 said:
So let me give you a little background first. I was at my brother's house recording him dunk in superslowmo. All of a sudden, my phone freezes. After about 2-5 mins I decide To hold power +volume down and the phone goes black and goes to the "Samsung Galaxy note 9 secured by knox" screen and does a infinite reboot to that screen. The phone will not go into recovery mode BUT will go into Download Mode. I tried letting the phone completely drain and then trying it with no success.
I do have AT&T protection on my device but the only thing they will do is replace it which I'm trying to avoid being that I have pictures I want to extract from the phone.
So to my question(s)
1) if I flash latest version of firmware from sammombile will I lose my pictures? (Trying to avoid loss of pics)
2) can I use a MacBook to do the reflashing or does it have to be windows?
Please and thx to all that respond!!!
Click to expand...
Click to collapse
1) while flashing in Odin, the CSC file determines if your phones data is erased or not during the flash. In order to retain personal data, flash HOME_CSC..
2) you can use Jodin to flash on a Mac https://forum.xda-developers.com/devdb/project/dl/?id=20803

Bober_is_a_troll said:
1) while flashing in Odin, the CSC file determines if your phones data is erased or not during the flash. In order to retain personal data, flash HOME_CSC..
2) you can use Jodin to flash on a Mac https://forum.xda-developers.com/devdb/project/dl/?id=20803
Click to expand...
Click to collapse
Okay I ditched the macbook idea and I have my aunt's computer in from of me.
When installing the firmware.. Am I going for the latest USA version which is from like last week... Or do I do the ATT firmware from Nov 2018 and do the OTA update?

Bicka0701 said:
Okay I ditched the macbook idea and I have my aunt's computer in from of me.
When installing the firmware.. Am I going for the latest USA version which is from like last week... Or do I do the ATT firmware from Nov 2018 and do the OTA update?
Click to expand...
Click to collapse
We're you already on the latest firmware? If you are then just flash the latest and use home_csc

Bober_is_a_troll said:
We're you already on the latest firmware? If you are then just flash the latest and use home_csc
Click to expand...
Click to collapse
Okay now one last problem .. I connected my phone to the pc and it made a chime sound like the pc recognized but noting popping up in odin.
When I go to download the drivers, it tells me I already have them downloaded and ask if I want to dl them again anyways which I do... Then at the end of the whole process it says failed to install and I'm in dl mode on my phone

Try different port on computer
Sent from my SM-N975U using Tapatalk

butchieboy said:
Try different port on computer
Sent from my SM-N975U using Tapatalk
Click to expand...
Click to collapse
When I did that I got this loading screen that says installing device but it hasn't moved from that "near end" of the loading screen for like 10 mins now

butchieboy said:
Once in download mode hold volume down and power to see if phone boots up. If you reflash with Odin use home_csc so it does not wipe your data. If you do get to recovery do not do a wipe, everything you have saved to phone storage will be gone. See if you can get to device storage by connecting to computer once your in download mode or recovery. If so just move all important files to computer then you can use Odin to flash firmware.
Sent from my SM-N975U using Tapatalk
Click to expand...
Click to collapse
Ever seen above Images?

Try installing Smart Switch

raul6 said:
Try installing Smart Switch
Click to expand...
Click to collapse
I'm going to try that now. Just look at what version of Windows I have and it's 8.1... does that make a difference of why the drivers won't install ?
This is the error message when I try "mss installwizard for samsung usb driver for mobile phones failed "

Bicka0701 said:
I'm going to try that now. Just look at what version of Windows I have and it's 8.1... does that make a difference of why the drivers won't install ?
This is the error message when I try "mss installwizard for samsung usb driver for mobile phones failed "
Click to expand...
Click to collapse
When I was installing smart switch it told me to "disconnect my device from pc"( which it read AS A Samsung phone)
But when it's all downloaded It just says connect device again but when I do the computer makes its sound and then nothing.
If I'm in device manager and I plug in my note 9 it pops up as 'sdm845' but says there are no drivers installed.
I uninstalled the Samsung drivers (even though it says failed) and I tried again and it said fail to install again

Okay if anyone Is still reading this.. If I switch up and use my Father's Macbook instead, does anyone know the necessary steps to continue on with the process? And keep in mind the state of my phone is in a boot loop and only goes to the download screen

I was just doing the whole chatting thing with a Samsung representative and they advise me to go to a place near me to do the reflashing.
but still the thing that's bothering me is that my PC isn't installing the drivers regardless.
without even thinking about my phone connected , I should be able to go on Samsung's website and download the drivers right off the website but when I do I get the "mss installwizard for samsung usb driver for mobile phones failed "

Install this drivers, reboot pc, open odin as administrator, connect phone in download mode.
http://www79.zippyshare.com/v/NJL6wZmq/file.html

Did you ever get to the bottom of this ? I seem to have a similar issue, where phone is in a continuous boot loop. It stays on powered by android screen for few secs and then restarts.
I cannot enter recovery mode, but can get into download mode. Have flashed via ODIN few times successfully, but same condition prevails.
Safe to assume MoBo is fried ?

Could be that the main storage in the motherboard is corrupted, which needs to be reformatted entirely.

dedicated2droid said:
Did you ever get to the bottom of this ? I seem to have a similar issue, where phone is in a continuous boot loop. It stays on powered by android screen for few secs and then restarts.
I cannot enter recovery mode, but can get into download mode. Have flashed via ODIN few times successfully, but same condition prevails.
Safe to assume MoBo is fried ?
Click to expand...
Click to collapse
No I never did get to the bottom of it. I ended up getting the Note 10 but I still have the Note 9 with Hopes one day someone figures it. I got pics of my son I would love to get off of there

Bicka0701 said:
No I never did get to the bottom of it. I ended up getting the Note 10 but I still have the Note 9 with Hopes one day someone figures it. I got pics of my son I would love to get off of there
Click to expand...
Click to collapse
Just a heads up, Google photos has free backups up to 15gb in full quality, or unlimited backup of 1080 for pics and videos. So at least from now-> forward a hardware issue won't ever cause you to lose pics again. You just need to open the app and setup backups.

Galaxy S10 bootloop after updte to Android 10

This morning I saw that I can update to the new Android 10 version on my Galaxy S10.
I was happy and of course updated directly.
Everything worked fine, the update was downloaded, installed and the phone rebooted.
And from there it hung in a boot loop.
I had already unlocked the bootloader 2 months ago, but only to flash the original firmware again because of an unsuccessful attempt to install TWRP.
Now the Galaxy S10 starts up, shows the information that the boot loader has been unlocked and then the boot logo and vibrates.
Then it goes straight off and starts again.
I cannot use the key combinations to get into the recovery or in the download mode.
How can I solve this problem ?
(Sorry for my bad englisch i come from germany)

You can try following:
Plug your phone in the PC with the USB cable. Then press/hold Bixby + Volume Down and hopefully it will boot to download-mode.
Otherwise try (still plugged in) force shutdown/restart by pressing/ holding Volume Down + Power - as soon as the screen turns off shift to pressing/ holding Bixby + Volume Down for download-mode. Try it at few times as its all about timing.
If still no luck, unplug your phone and let the battery run out. Then press/hold Bixby + Volume Down and plug in to get to download-mode. This may take some time as the phone needs to recharge a little before it reacts.
Once in download-mode flash your software before the update via Odin - I would use Home_CSC first trying to save your data.

Got exactly the same problem today. Don't know which one I flashed in november though
So how to keep (maybe) the data? flash only HOME_CSC?

nikolaus2007 said:
Got exactly the same problem today. Don't know which one I flashed in november though
So how to keep (maybe) the data? flash only HOME_CSC?
Click to expand...
Click to collapse
Yes to using Home_CSC but to be safe I would flash all 4 files (AP - BL - CP - HomeCSC) as some people have reported their storage gets corrupted/ shows wrong capacity.
Use either Samsung 10 (BSKO) or latest Pie (ASJG). Both should be ok as you are flashing the bootloader when using all 4 files.

Norup58 said:
You can try following:
Plug your phone in the PC with the USB cable. Then press/hold Bixby + Volume Down and hopefully it will boot to download-mode.
Otherwise try (still plugged in) force shutdown/restart by pressing/ holding Volume Down + Power - as soon as the screen turns off shift to pressing/ holding Bixby + Volume Down for download-mode. Try it at few times as its all about timing.
If still no luck, unplug your phone and let the battery run out. Then press/hold Bixby + Volume Down and plug in to get to download-mode. This may take some time as the phone needs to recharge a little before it reacts.
Once in download-mode flash your software before the update via Odin - I would use Home_CSC first trying to save your data.
Click to expand...
Click to collapse
Thanks!
I got into the download mode.
I used SamFirm to download the firmware but it was Android 10
Right now i am downloading Andoid Pie from updato.com...
No premium, i am just a free member, so it shows me "20 Hours left"
Where can i download the latest SM-G973F Germany (DBT) Android Pie Firmware for free and without that high speed restriction ?
I think i have to put the home_csc file into the CSC field in odin ?

Didn't work for me, neither ASJG (Pie) nor BSKO (Q).
Had to wipe data, beause system nerver booted again.
Lost all my data. Congrats Samsung to this very best update mechanism. Nerver had on any Nexus nor OnePlus.
Maybe you have more luck.

download mode its not opening idk what i need to do im gonna lose my mind ( sorry for my bad english )

c_j_k said:
Thanks!
I think i have to put the home_csc file into the CSC field in odin ?
Click to expand...
Click to collapse
Yes!
maxmelax said:
download mode its not opening idk what i need to do im gonna lose my mind ( sorry for my bad english )
Click to expand...
Click to collapse
Have you tried all 3 of my suggestions listed above?

Norup58 said:
Yes to using Home_CSC but to be safe I would flash all 4 files (AP - BL - CP - HomeCSC) as some people have reported their storage gets corrupted/ shows wrong capacity.
Use either Samsung 10 (BSKO) or latest Pie (ASJG). Both should be ok as you are flashing the bootloader when using all 4 files.
Click to expand...
Click to collapse
I flashed G973FXXS3ASJG to my Galaxy S10.
First i tried only homeCSC but it was still brick.
Then i flashed only AP, it worked.
But after I set up my smartphone again, I saw that I only have 32 GB of storage even though my Galaxy S10 is the 128 GB version.
Then, as you said, I flashed all four files (AP - BL - CP - HomeCSC).
It still shows me that I only have 32 GB of storage

c_j_k said:
I flashed G973FXXS3ASJG to my Galaxy S10.
First i tried only homeCSC but it was still brick.
Then i flashed only AP, it worked.
But after I set up my smartphone again, I saw that I only have 32 GB of storage even though my Galaxy S10 is the 128 GB version.
Then, as you said, I flashed all four files (AP - BL - CP - HomeCSC).
It still shows me that I only have 32 GB of storage
Click to expand...
Click to collapse
When I first read your post I thought:
Seriously…. Seriously…..
I mean, why the heck would you only flash one file (you were actually warned against this) when it is just as easy to fill-out all 4 slots in Odin? People amaze me!
Okay its Xmas, so back to helping:
‘What you have experienced is a side-effect of using Odin to flash an AP file to your device with the CSC slots left empty. Never flash a full AP file on this range of devices without also filling at least the HOME_CSC slot. It is safe, however, to flash only a recovery image in the AP slot.
To attempt to repair the damage, you need to boot to TWRP, select Advanced Wipe, tick Data, select Repair or Change File System followed by Resize File System. Your /data will return to its former size, but you will probably find you have lost some data.’
Above is quoted from #ianmacd
So, if your phone is on stock Pie (minimum ASIG), with OEM unlocked, try this to get TWRP installed in order to use above rescue.
Go here and download Multidisabler: https://forum.xda-developers.com/ga...ynos/g97xf-multi-disabler-encryption-t3919714
Go here and download TWRP Magisk Patched: https://forum.xda-developers.com/ga...ynos/recovery-twrp-galaxy-s10-magisk-t3919248
Now read post #2 in the TWRP thread for installation guidance…. When you get to no.10 flash the Multidisabler you downloaded instead and then skip to no.12
After no.12 reboot, boot back into TWRP and try the Data fix above.
If all goes well you will have full storage capacity again, TWRP installed and rooted with Magisk.

Norup58 said:
You can try following:
Plug your phone in the PC with the USB cable. Then press/hold Bixby + Volume Down and hopefully it will boot to download-mode.
Otherwise try (still plugged in) force shutdown/restart by pressing/ holding Volume Down + Power - as soon as the screen turns off shift to pressing/ holding Bixby + Volume Down for download-mode. Try it at few times as its all about timing.
If still no luck, unplug your phone and let the battery run out. Then press/hold Bixby + Volume Down and plug in to get to download-mode. This may take some time as the phone needs to recharge a little before it reacts.
Once in download-mode flash your software before the update via Odin - I would use Home_CSC first trying to save your data.
Click to expand...
Click to collapse
i am having the same problem but i cant enter download mode and my pc doesnt recognise the phone to use odin
is there any possible solution to that ? thank you in advance

th3maker said:
i am having the same problem but i cant enter download mode and my pc doesnt recognise the phone to use odin
is there any possible solution to that ? thank you in advance
Click to expand...
Click to collapse
Yeah, I can see you have started a thread with your problem.
If the first two of my suggestions doesnt work for you then you have to let the phone bootloop until the battery dies/ runs dry and then try my third suggestion.

Norup58 said:
When I first read your post I thought:
Seriously…. Seriously…..
I mean, why the heck would you only flash one file (you were actually warned against this) when it is just as easy to fill-out all 4 slots in Odin? People amaze me!
Okay its Xmas, so back to helping:
‘What you have experienced is a side-effect of using Odin to flash an AP file to your device with the CSC slots left empty. Never flash a full AP file on this range of devices without also filling at least the HOME_CSC slot. It is safe, however, to flash only a recovery image in the AP slot.
To attempt to repair the damage, you need to boot to TWRP, select Advanced Wipe, tick Data, select Repair or Change File System followed by Resize File System. Your /data will return to its former size, but you will probably find you have lost some data.’
Above is quoted from #ianmacd
So, if your phone is on stock Pie (minimum ASIG), with OEM unlocked, try this to get TWRP installed in order to use above rescue.
Go here and download Multidisabler: https://forum.xda-developers.com/ga...ynos/g97xf-multi-disabler-encryption-t3919714
Go here and download TWRP Magisk Patched: https://forum.xda-developers.com/ga...ynos/recovery-twrp-galaxy-s10-magisk-t3919248
Now read post #2 in the TWRP thread for installation guidance…. When you get to no.10 flash the Multidisabler you downloaded instead and then skip to no.12
After no.12 reboot, boot back into TWRP and try the Data fix above.
If all goes well you will have full storage capacity again, TWRP installed and rooted with Magisk.
Click to expand...
Click to collapse
Hey Bro, I bricked my phone as well in the morning while updating to android 10 but I just had my bootlocker unlocked but no root on it. Could you tell me if there is any possibility to backup the stuff on my phone? Right not Im waiting for my battery to drain to 0% that I can get into download mode and try something out maybe you have a tip for me

Can someone send me a prepatched magisk ap file for HK 9730 Android 10. I don't know what I did. I just pre patched it myself and flashed with odin just like ANY other update but this time, it gets stuck at Samsung logo. I waited a good while too. Maybe I didn't have the right magisk version which is why I'm asking if someone has a pre patched that works, idk but I don't want to lose my data.

BeastyReedhawk said:
Hey Bro, I bricked my phone as well in the morning while updating to android 10 but I just had my bootlocker unlocked but no root on it. Could you tell me if there is any possibility to backup the stuff on my phone? Right not Im waiting for my battery to drain to 0% that I can get into download mode and try something out maybe you have a tip for me
Click to expand...
Click to collapse
My suggestion is to download the complete stock firmware- be it Pie or 10 (Q) - and then when flashing all 4 files via Odin use the Home_CSC file to try to retain your data.
I use FRIJA to download firmwares as the d/l speed is very good.
Bear in mind, if you at some point intend to root and/or install TWRP your phone will be wiped in the process so backup your stuff before going down that road.

Hi, i have the same problem, i can't access to download mode, i have access to twrp recovery but i can't do anything, if i touch the recovery screen, the phone reboot, have you any suggestion please, to recover my phone?
OK, i find a way accidently!
thks

I am also experiencing this issue that the OP is having with their S10. I also have an S10. There was a software update for my phone and now I wake up to my phone boot looping itself to death.
For someone that lives in the United States, which firmware should I use to recover my phone? I ask because there is like 20+ countries to choose from for the exynos G973F model

Norup58 You saved my life!!!! LOVE YOU. i got into download mode THANKS MAN
LOVE UU

My have a similar problem buh worse... Was updating manually then got the error message.
Tried to put it back into download mode the went into black screen and now doesn't respond to anything. Seems dead

RemixDeluxe said:
I am also experiencing this issue that the OP is having with their S10. I also have an S10. There was a software update for my phone and now I wake up to my phone boot looping itself to death.
For someone that lives in the United States, which firmware should I use to recover my phone? I ask because there is like 20+ countries to choose from for the exynos G973F model
Click to expand...
Click to collapse
Hello,
I have a Samsung Galaxy Note 9 (SM-N9600) that will not boot. So far I have flashed 2 official firmwares with Odin, and on the first boot attempt after flashing, it will show a percentage bar that counts up to around 5 or so percent before skipping to 100 then looping again. It only does the percentage thing on the first boot after flashing. When I try a factory reset from the recovery I get a no pdp scenario error also. I have tried all that I can think of and even took it to a Samsung Service centre but no solution. I would really appreciate any help I can get.