NOTE: THIS SOLUTION IS POTENTIALLY DAMAGING AND MAY NOT WORK FOR EVERYONE
PROBLEM: touch screen acts erratic, notification bar keeps opening, screen appears to be touched by someone else continuously (Ghost Touch), and parts of the screen DO NOT RESPOND TO TOUCH.
MY OWN SPECIFIC CASE: I had the Ghost Touch issue for 3 days suddenly without intro, which often used to go away after a reboot or two, then phone worked normally after I removed the battery and left it in a dry area (in a closed drawer between books, no air entering, very dry atmosphere), however the RIGHT SIDE of the screen (Search button, rightmost letters [L and Delete and sometimes ENTER] do not work. If the phone is in normal landscape, you cannot open the notification bar by dragging it normally.
DIAGNOSIS: for some people, the problem is more severe. The Digitiser itself could be malfunctioning and has to be fixed, while for others it could be a true problem with the screen itself. However, for MANY OF US, it is a problem of HUMIDITY. The humidity sensors are causing the phone to act like that. Some say part of this problem happens because the way the keypad affects the phone internally as you open and close it a lot.
SOLUTIONS:
1- To be safe: send the phone to the shop. Ask them to open the phone and apply an extra layer of insulation, in case the digitiser and the screen are okay.
2- If something is faulty, replace it at the shop.
3- MY OWN SOLUTION: based on something I read many times, the solution was to apply DRY HEAT for at least 45 mins. What I did, based on averaging out many experiences I read online, was to remove the SD Card and SIM, remove battery, I heated up a toaster oven for 10 minutes, waited until the temperature was at about 60-70 degrees Celsius, SHUT DOWN THE HEAT, put the phone on its screen on a plate, screen facing down and covered by a cloth to protect it from direct contact with metal, then all inside the oven. The oven is a relatively big one, so phone was AWAY FROM A SOURCE OF DIRECT HEAT. I closed the lid, then every while 15 minutes I would heat the oven for 40 seconds to maintain the temp. This is LIKE (ALTERNATIVE SOLUTION) leaving your phone in the glove compartment of your car while its parked in a sunny spot, to find it really hot in the morning and tough to touch for a while. TO CONTINUE, after the phone was out of the oven (I can't believe I am saying this), I left the phone overnight in a dry area for 8 hours (could need less time). Then, I put everything back in, plugged it, and THE PHONE IS WORKING PERFECTLY NOW!
NOTE that solution number 3 could affect your keyboard buttons if heat is too much. It may cause the glue holding the keys to melt a bit. Be delicate with your keyboard after you restore your phone.
Again, I only did this YESTERDAY. With the exception of some keypad stickiness, the phone is working perfectly now.
I hope this was useful
B.
EDIT: Today is the First of May, phone is still working without a glitch
N.B. Press the Thank you button if you wanna congratulate me on daring to toast my milestone in the name of scientific inquiry
SECOND EDIT: Phone did it again for 2 days. Applied the same method, and it worked again. I think partially it happened because I was in a very humid location.
That didn't work for me, I had no option but to replace the touchscreen/gorila glass.
I love the idea of toasting a milestone
Thought with all my aggression against Moto, I think I just might leave it in there
Luckily I dont have these problems so I wont get tempted
AirLancer said:
I love the idea of toasting a milestone
Thought with all my aggression against Moto, I think I just might leave it in there
Luckily I dont have these problems so I wont get tempted
Click to expand...
Click to collapse
I have to admit, I cared litte whether or not this actually worked. I just wanted to toast it But it did work, so
Pretty tempted to try this out, I think I will when I have free time.
My phone had the dead zone problem for 2 months now, but in some very rare cases, like when it's a very hot day, the screen will work normally for a minute or something. Then it goes back to dead part. I assume this would fix it?
Lesiroth said:
Pretty tempted to try this out, I think I will when I have free time.
My phone had the dead zone problem for 2 months now, but in some very rare cases, like when it's a very hot day, the screen will work normally for a minute or something. Then it goes back to dead part. I assume this would fix it?
Click to expand...
Click to collapse
If it DOES indeed work on hot days, then it means the phone is not entirely dead. But I would suggest you do something less drastic first, such as the Glove Compartment method. No responsibility though
If you're trying to remove moisture, you could also try putting it in a baggie of crystaline cat litter (NOT the clay kind!) - this stuff is sold at a MUCH higher price as a way to save a phone from water damage, but it's the exact same substance. Does a great job removing moisture. It's the same sort of silica gel that's in those packets in medicine/vitamins that says "Dessicant - do not eat".
Or you could just put it in a sealed bowl with raw rice for a couple of days... this is the best and cheapest way (and then you have the silicon "grains", the ones that you find in shoe boxes or computer parts boxes).
Sent from my Milestone using Tapatalk
CybeRNerO said:
Or you could just put it in a sealed bowl with raw rice for a couple of days... this is the best and cheapest way (and then you have the silicon "grains", the ones that you find in shoe boxes or computer parts boxes).
Sent from my Milestone using Tapatalk
Click to expand...
Click to collapse
Pretty sure that rice doesn't do anything, I don't know how that started as a suggestion, but its not better than anything else; its not known to be absorbant, but the silicon is.
I've tried the method but the right segment of the digitizer still doesn't work.
My biggest issue with regards to "lack of responsiveness" are the 4 capacitive buttons. Pressing the Home key is always hit and miss. I know I hit it all the time because I can feel the vibration feedback but it only goes to homescreen 50% of the time.
Will also be testing this out as soon as I have the spare time. My screen started acting up after I accidentally put my milestone in a small beer spill at a party Hopefully this will work out for me too!
Abazel said:
I've tried the method but the right segment of the digitizer still doesn't work.
Click to expand...
Click to collapse
Luckily for me, I was still under warranty, heh. Cause I had insurance. This is my second Droid this has happened to. Hopefully my replacement won't do the same thing.
How many times did you reheat the oven? I tried just once and it didn't help. My phone has been having this problem since January.
decon89 said:
How many times did you reheat the oven? I tried just once and it didn't help. My phone has been having this problem since January.
Click to expand...
Click to collapse
I feel I am on a cooking show
Well, depends on your over. Mainly I was trying to maintain a temp varying between 50-60 c. Mostly 50, but sometimes 60 to up the ante a bit and make sure things stay warm. 30 minutes at least. However, I have to say that I did this twice in 6 weeks, and after that the phone just died again, and I found my warranty card and sent it there to be fixed, and they fixed it, but ruined something else.
If you have the warranty card, take your phone and send it to them Someone told me the method worked and the phone has been good for quite a while, but most of us seem to re-experience the issue after a while.
I've been having these issues for a few days now too, and I think I know why. I've been using this Milestone for 4 months now, and I never had this problem until a few days ago. What I noticed yesterday was that after some acting up, the phone started working properly again. So I ran Touch Test. And I noticed that if I pressed really hard on the top side of the phone(where the logo and the ear piece are located) it started acting up again. My first impression was that the glue holding down the gorilla glass was loose. So I left the phone as usual on my night stand and then I tried the same thing with the pressing on the same area. Guess what? It didn't happen again. Now there seems to be no problem. So I tried to remember what happened yesterday before the screen started acting up, and I remember talking to my wife for a while when I was in my car. Yesterday was a pretty hot day and I was a little sweaty when I talked to her. Now since only that specific part with the earpiece was causing this issue(I tried pressing equally hard on other areas without any problem my guess is that the insulation between the earpiece and the touchscreen has been breached. Maybe because of all the sweat that went in there in time. You know the salt and acids in the swear are known to melt things, and poor quality glue is among them.
How to fix this? I do not know yet, but I do have a good idea that I'd like to share. I want to buy a screen protector foil, and put just a little band around the ear piece. That would probably lower my in-call volume, but since the Milestone is very loud anyway I hope it the quality of the calls won't be too much affected. After that I'll use it in normal conditions again and see if the ghosting happens again.
try completely formatting your SD CARD/PARTITION.
& then reinstalling using (FAT 32/EXT 2, 3, or 4)
sometimes traces from the previous ROM might interfare with touch codecs (maybe)
just trying to help. had similar issue & this is what i did.
bandroid842 said:
NOTE: THIS SOLUTION IS POTENTIALLY DAMAGING AND MAY NOT WORK FOR EVERYONE
PROBLEM: touch screen acts erratic, notification bar keeps opening, screen appears to be touched by someone else continuously (Ghost Touch), and parts of the screen DO NOT RESPOND TO TOUCH.
MY OWN SPECIFIC CASE: I had the Ghost Touch issue for 3 days suddenly without intro, which often used to go away after a reboot or two, then phone worked normally after I removed the battery and left it in a dry area (in a closed drawer between books, no air entering, very dry atmosphere), however the RIGHT SIDE of the screen (Search button, rightmost letters [L and Delete and sometimes ENTER] do not work. If the phone is in normal landscape, you cannot open the notification bar by dragging it normally.
DIAGNOSIS: for some people, the problem is more severe. The Digitiser itself could be malfunctioning and has to be fixed, while for others it could be a true problem with the screen itself. However, for MANY OF US, it is a problem of HUMIDITY. The humidity sensors are causing the phone to act like that. Some say part of this problem happens because the way the keypad affects the phone internally as you open and close it a lot.
SOLUTIONS:
1- To be safe: send the phone to the shop. Ask them to open the phone and apply an extra layer of insulation, in case the digitiser and the screen are okay.
2- If something is faulty, replace it at the shop.
3- MY OWN SOLUTION: based on something I read many times, the solution was to apply DRY HEAT for at least 45 mins. What I did, based on averaging out many experiences I read online, was to remove the SD Card and SIM, remove battery, I heated up a toaster oven for 10 minutes, waited until the temperature was at about 60-70 degrees Celsius, SHUT DOWN THE HEAT, put the phone on its screen on a plate, screen facing down and covered by a cloth to protect it from direct contact with metal, then all inside the oven. The oven is a relatively big one, so phone was AWAY FROM A SOURCE OF DIRECT HEAT. I closed the lid, then every while 15 minutes I would heat the oven for 40 seconds to maintain the temp. This is LIKE (ALTERNATIVE SOLUTION) leaving your phone in the glove compartment of your car while its parked in a sunny spot, to find it really hot in the morning and tough to touch for a while. TO CONTINUE, after the phone was out of the oven (I can't believe I am saying this), I left the phone overnight in a dry area for 8 hours (could need less time). Then, I put everything back in, plugged it, and THE PHONE IS WORKING PERFECTLY NOW!
NOTE that solution number 3 could affect your keyboard buttons if heat is too much. It may cause the glue holding the keys to melt a bit. Be delicate with your keyboard after you restore your phone.
Again, I only did this YESTERDAY. With the exception of some keypad stickiness, the phone is working perfectly now.
I hope this was useful
B.
EDIT: Today is the First of May, phone is still working without a glitch
N.B. Press the Thank you button if you wanna congratulate me on daring to toast my milestone in the name of scientific inquiry
SECOND EDIT: Phone did it again for 2 days. Applied the same method, and it worked again. I think partially it happened because I was in a very humid location.
Click to expand...
Click to collapse
Thank you for that Solution.
It fixed the Issue of my friends MS without other problems
I'll have to try and the oven methode again. My phone has started to really act up again.
I've tried to install new roms, wipe ect. and it doesn't help with the screen.
Have anyone tried to replace the digiziter? They are pretty cheap on ebay
My milestone started freaking out just an hour ago. No more warranty here but I'm not brave enough to do the oven method. Had anybody tried the Rice alternative?
my phone is having difficulties with the touch screen. at the top of the screen, it totally wont work when I touch it. do I need to replace the screen or is there a way to fix it? I cleaned the screen many times so, help me?
It's just the top part that isn't responsive?
DO AT YOUR OWN RISK!!!!! but it worked for me with my screen problems. I had dropped my poor hero in a glass of water. After quick action and rice it was dried pretty good but the bottom screen would go all wonky and only a reboot sort of fixed it till I stumbled on Google.
1st take out the battery and SD card!!!!!!! Can't stress this enough.
I had found if you took a hair dryer on high heat for about 2 minutes and move it around the screen during that time so as to not heat just a certain spot. After the approximately 2 minutes place something heavy like a big book but not too heavy to crack the screen and place it on top of the phone til it cools. About 15 minutes. Replace SD card and battery and boot up. Should be responsive as hell now.
Haven't had an issue since and can't tell its been in water unless you look at the stickers ... oh well I'm never selling it so
I had been dealing with the same nightmare your complaining of for weeks.
Eventually i had to reflash the clean sprint OS and take it to the store and within an hour they had replaced the touch screen and it was just like new. As of yesterday I did not have insurance but fortunately they have open enrollment for it, and at a cost of $4 for comprehensive insurance they were able to replace the touch screen.
Before biting the bullet and taking it to tech support I tried recalibrating the keyboard, flashing tons of different roms, cleaning it, but finally brought it in. I suggest you do the same since we are not the only ones complaining of this problem. Goodluck
Hello,
My note fell into the water last night and it was a pain in the ass to fix. I kept my phone in a bag of rice overnight to soak up most of the water. Today I took it apart and removed the remaining water and put it back together. The phone finally works again! Yes, it all works except for the service.
When I unlock my sim with my code everything works, but I cannot call or be called because there's no service, even though whatsapp etc works fine.
Can anyone help me with this?
Also: sometimes it DOES work, but the signal is very weak. Sometimes I can call and be called and sometimes I cannot.
You might have disconnected the antenna while taking it apart. Check for bent connectors etc. You can also check the external antenna - remove the small black rectangular sticker on the right side of microsd slot above the battery. You can insert a thin copper wire with a piece of aluminum foil connected to it - you should get some reception. If you don't and you internal antenna is properly connected then the water might have damaged some electronics. It can get expensive.
Be careful and don't hold me responsible if you mess up your phone any further. And good luck.
I'm not sure. I'm still getting a signal every now and then. Is there a video on how to do this by any chance? And do you have a picture of the antenna by any chance so I know what to look for?
Sorry, can't be of much help here, never had to open my Note. But I remember back in days whaen I messed around with my Touch Pro 2 and HTC Desire it was a common issue. Nearly every time I got the phone back together either phone signal or Bluetooth were gone and the reason was always some bent copper connectors that didn't stick together when all the parts were back in place. These things are fragile. Sometimes had to clean them as well. Google for Samsung Galaxy Note N7000 disassembly manual, I'm sure there will be one with decent pictures somwhere online, it'll help you locate the internal antenna. If there's some weak signal sometimes it's a good sign and looks very much like disconnected antenna, you may check the external one to be 100% sure.
Edit: the antenna is a thin copper sticker somewhere on a flat surface of the chassis, either on the side or around the camera or something like that. It's often painted in the color of the chassis to prevent it from oxidation. There are several - phone, bluetooth, probably wifi and maybe GPS (dunno). It's usually possible to follow where it leads to and find connectors.
http://www.youtube.com/watch?v=N6CJy71_9Ok
watch the whole thing but pay particular attention around 3:10
Hi all . Wishing you all a happy holi.
Well as the thread says and since its holi (no explanation required) my phone seems to have shutdown after my friends and I were playing with a water pipe and I (for kicks) hosed my Xperia Z full of water.
After reading a few threads I came to understand that there are damage strip indicators on all panel flaps.
The micro SD flip is still white but the charger/usb cable and headphone jack flaps have turned pink,
The phone also crashed sometime after I hosed it with water and is not powering up.
So what should I do now?
Currently I'm on the advice of 3 friends using the rice method. I have opened all flaps of the phone and submerged it in a bowl of rice so that it dries out all the moisture. I intend to keep it the whole night and try powering it up in the morning.
Options:
1. Try the rice method and hope it works (yay)
2. After failing point 1, keep it in the sun/blower/hair dryer method and try again to power it up,
3. Take it to the Sony Service Center in Lajpat Nagar (I'm from New Delhi) and give it for repair.
P.S - My phone is rooted and running cyanogenmod. Will they charge me extra If I happen to give it for repair when they find out I'm running a custom mod.
I'm asking because Sony does weird things. When I bought the phone last year I dropped it on the ground and scratched a corner. Not too much but the phone was only 3 months old and I felt bad about it so I thought I get the body changed for a small fee.
Turns out Sony does not replace the phone body instead the executive simply told me to pay 50% of the price and I could get a whole new phone since the Xperia's body cannot be changed.
Kindly help!
Thank You
same here though my power button is ****ed up right now.... i have it dipped in rice and would let it be there for 2-3 days...
P.S even my headphone jack and usb are pink now.... i never had it removed from my pocket but had a lot of water splashes...
THIS THREAD SHOULD BE CLOSED. PROBLEM HAS BEEN SOLVED.
My gratitude to the people who were kind enough to reply to my private messages.
Point no. 1 worked.
I covered the phone in rice in a plastic bowl and left it for a whole day in my car where it got heated.
After that I tried powering it on. Seeing as I had already pretty much destroyed the phone I decided to give it one last shot on charging the phone which I hadn't done in case it short circuits and voila! The red light turns on and my phone is charging.
No problems detected.
Network/3G is working. Tried whatsapp, sms and used the camera and music player. Speakers are fine too. Same goes for the screen. Seems no damage done to the phone at all. Will need to change the screen guard though. Its become moist. I'll use the phone and reply on how the battery has been performing.
I'm sold. This is a SOLID PHONE. And I was worried that I'd have to shell out 15-20k because the damage indicators on the 2 flaps had turned pink.
Yup same here.... Although as I had water in my back camera.... It's left dust on my camera lens
Sent from Dilli
hello man i couldn't understand your message anyway i got my phone fixed , the only problem i had was with the fog on the cameras which gone after 2 days by it self and also i used the bag which has small balls in it which take the humidity away
OK, I wish I had pictures to show, but I have none. Sorry. (My phone is my only camera)
So a couple weeks ago I managed to break my digitizer. Thought I would post my experience with replacing it, to better inform those daring enough to try, and to warn off those without the tools to do so.
Tools needed: screwdriver (Phillips head), something to open the case, and aheat gun, and lots of time and patience.
First I ordered in a new screen replacement. It was a touchscreen/LCD package deal. This one: http://www.aliexpress.com/item/Orig...-mi-Assembly-with-front-frame/1593196482.html
Then opened the Sim card tray and took out the two screws that must be removed to take the back cover off
Once the back cover is removed, there are to covers to remove, 3 screws on the bottom cover, and I believe 8 on the top cover. Once the covers are removed, there are 2 more holding in the motherboard.
Now for the annoying revelation. You don't swap the screen, you swap everything else to the new screen. Seriously, the frame that the screen is mounted to has everything that isn't screwed to it, glued to it. This is where the heat gun is needed. Heat the parts glued down, and gently pull them up. Then stick them to the new frame. EVERYTHING must be swapped.
The entire process took me about 2 hours to work through and figure out. I broke a connector on the motherboard to the high frequency antenna on the left side of the battery. Phone works without it, but I list 1 signal bar everywhere I go now. I also managed somehow to break the backlight for the buttons at the bottom of the screen, and lastly, I somehow messed up the back camera. Its no longer focused right. I don't see much difference in overall quality between the front and back cameras now.
Will update with links later, and attempt the borrow a camera to get some decent pics to show what all is involved. I've replaced screens before on other devices, but never anything anywhere this complicated before.
StridAst said:
OK, I wish I had pictures to show, but I have none. Sorry. (My phone is my only camera)
So a couple weeks ago I managed to break my digitizer. Thought I would post my experience with replacing it, to better inform those daring enough to try, and to warn off those without the tools to do so.
Tools needed: screwdriver (Phillips head), something to open the case, and aheat gun, and lots of time and patience.
First I ordered in a new screen replacement. It was a touchscreen/LCD package deal. Will update a link to the aliexpress seller later.
When it arrived, I took apart my mi3. First there are 2 screws inside the Sim card tray. Must be removed to take the back off.
Once the back cover is removed, there are to covers to remove, 3 screws on the bottom cover, and I believe 8 on the top cover. Once the covers are removed, there are 2 more holding in the motherboard.
Now for the annoying revelation. You don't swap the screen, you swap everything else to the new screen. Seriously, the frame that the screen is mounted to has everything that isn't screwed to it, glued to it. This is where the heat gun is needed. Heat the parts glued down, and gently pull them up. Then stick them to the new frame. EVERYTHING must be swapped.
The entire process took me about 2 hours to work through and figure out. I broke a connector on the motherboard to the high frequency antenna on the left side of the battery. Phone works without it, but I list 1 signal bar everywhere I go now. I also managed somehow to break the backlight for the buttons at the bottom of the screen, and lastly, I somehow messed up the back camera. Its no longer focused right. I don't see much difference in overall quality between the front and back cameras now.
Will update with links later, and attempt the borrow a camera to get some decent pics to show what all is involved. I've replaced screens before on other devices, but never anything anywhere this complicated before.
Click to expand...
Click to collapse
We had one in the shop this past week as well. Not too horrible. About on par with many of the LG phones as far as repair-ability. Daniel