Hey all,
I have Zuk z2pro z2121. I wanted more than stock ROM so I downloaded zui 2.5.344. I unlocked bootloader n rooted my phone as well as installed TWRP. "Tool All in one" PC software helped me to carry out above with ease.
While playing around I clicked "Lock Bootloader" and phone got switched off with indicating continuous blue light. I tried pressing vol down + power + Home button, and several other combination but didn't help. When I pressed power button for long, I got Zuk logo onscreen with a white flash on indicator for 1 sec and then again the blue light indicator.
After a little RnD after pressing power button till I got white flash for 3 times and the blue light got completely off. I don't know what to do further. I have backup of my boot , recovery and ROM. Kindly suggest.
Shoaib
Press and hold volume - and power . Release power, after vibration you can release the volume -. You will be in that menu https://ibb.co/f3vOHm . Go to device manager and check if pc recognize your phone https://ibb.co/bHqZOR . Open CMD in adb folder and write adb devices https://ibb.co/cwCg3R . Then adb reboot edl . You are i EDL https://ibb.co/cvjiHm . Use Qfil to flash stock rom
Didn't work...
Thanks for responding. As said, tried pressing Vol + Power and never got any vibrations. Tried Up vol + power, tried Down vol + power. No vibrations.
When I press power button with any combination, this is what happens,
After Approx 15 secs - 1 white light flash in place of blue along with ZUK pic on d display (stays approx 1 sec)
Still keeping power button pressed
After approx 7-8 secs - same as above
Still keeping power button pressed
After Approx 15 secs - 1 white light flash in place of blue along with ZUK pic on d display (stays approx 1 sec)
But now after this third time of flash, blue light appears and after 4-5 secs disssappears. If I leave the button only at this time, the blue light doesn't comes back.
If I leave the power button before or after this sequence, the blue light doeanon the indicator doesn't goes off at all.
What is happening when you connect phone with pc ? Is there any reaction ?
No reaction from PC.
I tried connecting to PC, earlier Tool all in one immediately use to detect, n now there is no response from the PC or the software after making USB connection.
Sir,
As I said earlier, I clicked lock bootloader, n when the screen went off, I disconnected the phone from PC. There is a possibility of the boot partition getting damaged or so. Kindly assist.
Rgds
There aren't any ways to enter in fastboot or recovery , even in service menu . I think you should try deep flash cable to enter in EDL .
Will do as u say. Just one last thing, when I checked device manager in my PC, it showed the phone as other devicez "QUSB XXXX". Question is,
1. Any possibilities of recovery without going for a deep flash, as I got to learn it first.
2. Other part is, my phones battery seems to be drained now. So, it won't be a problem for a deep flash.
Could you give some print screen ?
The matter is that you must switch your phone to edl . Try this yet . Your phone must be turn off .
Press only volume up button for 10 sec and while keeping it pressed,connect phone to PC . Hold volume up until your PC finds a new hardware . It should be android phone - ShenQi composite adb interface . If it doesn't work I have no more ideas apart from df cable . This cable works on Zuk z2 and I think it should works on our Zuk z2 pro
Sir,
I managed to connect the phone via USB as 9008. Miflash not supporting my ROM. Will download Stock ROM n then try with QFIL and MiFlash as well. Thanks for all your support. Will keep u posted about the progres. XML file is not found in any ROMs I have. Miflash some error also but detecting the device. Is there any other tool similar to Miflash, which I can try..
Rgds
First use QPST/Qfil . Follow this guide https://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
Do all steps .
Good day.
I tried QFIL as well as Mi flash tool. Both showing errors. QFIL displaying Qualcomm HS USB QLoader 9008. But when downloading content , it shows Sahara error with even initiating the installation. After browsing a bit, started eMMC software download, and found displaying COM20 No phone connected. Can u assist me to fix this. I mean the phone must be in download mode. But how ?
Miflash, on the other hand shows Hello packet error. Don't know how to fix.
Things I did to fix above errors,
1. Copied ROM to Qualcomm/ bin file
2. Copied ROM to C:/
3. Tried using different USB ports
4. Tried different USB cables
5. Uninstalled n reinstalled USB driver, adb n fastboot, qpst, n miflash many a times along with restarting my PC.
None of the above helped.
I think, if eMMC software download starts displaying COM20 Phone connected, then the issue might be sorted out.
Kindly assist.
Rgds
DrTahseen said:
Good day.
I tried QFIL as well as Mi flash tool. Both showing errors. QFIL displaying Qualcomm HS USB QLoader 9008. But when downloading content , it shows Sahara error with even initiating the installation. After browsing a bit, started eMMC software download, and found displaying COM20 No phone connected. Can u assist me to fix this. I mean the phone must be in download mode. But how ?
Miflash, on the other hand shows Hello packet error. Don't know how to fix.
Things I did to fix above errors,
1. Copied ROM to Qualcomm/ bin file
2. Copied ROM to C:/
3. Tried using different USB ports
4. Tried different USB cables
5. Uninstalled n reinstalled USB driver, adb n fastboot, qpst, n miflash many a times along with restarting my PC.
None of the above helped.
I think, if eMMC software download starts displaying COM20 Phone connected, then the issue might be sorted out.
Kindly assist.
Rgds
Click to expand...
Click to collapse
U need ufs flash not emmc. Change programmer in qfil.
I have a some experience with miflash but I use it for xiaomi . I've never flashed my zuk z2 pro by miflash . If you want to use miflash use 2016.03.30 and run it on PC with win 64 . Create a folder on c: for example "zuk" and copy to that all contents of unrar Qpst/Qfil zui rom . If you have Qualcomm hs usb 9008 that means your phone is in edl ( download mode ) . Good luck
I appreciate all ur support....
As suggested, tried Miflash 30.03.2016 also. This ones showing class not registered.
No of things i did to overcome this errors.
1. Changed my PC to developer mode. Allowed portable device connections n stuff.
2. Visual studio C++ 2010 was installed along with Qualcomm driver, i believe thats sufficient.
3. Disabled my Firewall.
4. Downloaded n copied some atl70.dll file to my syswow64 folder as well as sys32 folder.
Tried all flash tools again after these changes....Same negative results.
Any further advices !!!
Regards
It's fault of drivers . Go to device manager and chose qualcomm hs usb 9800 and update driver automaticly . The second matter concerning of flashing by qpst/qfil - why did you put rom in qpst location ? . It must be for example on desktop in one folder . The simplest path is better . Don't use spacebar . Load content you must chose from that rom . Don't use other location . It's not necessary . Could you give some screenshots with qfil errors
DrTahseen said:
I appreciate all ur support....
As suggested, tried Miflash 30.03.2016 also. This ones showing class not registered.
No of things i did to overcome this errors.
1. Changed my PC to developer mode. Allowed portable device connections n stuff.
2. Visual studio C++ 2010 was installed along with Qualcomm driver, i believe thats sufficient.
3. Disabled my Firewall.
4. Downloaded n copied some atl70.dll file to my syswow64 folder as well as sys32 folder.
Tried all flash tools again after these changes....Same negative results.
Any further advices !!!
Regards
Click to expand...
Click to collapse
Did u use ufs flash in qfil instead of emmc?
Starchm said:
Did u use ufs flash in qfil instead of emmc?
Click to expand...
Click to collapse
Yups !!! I already did with Meta Build Type selection. Didnt Help. I tried to search for mbn file also to try emmc but cudnt find so was stuck with ufs....
mar.ur said:
It's fault of drivers . Go to device manager and chose qualcomm hs usb 9800 and update driver automaticly . The second matter concerning of flashing by qpst/qfil - why did you put rom in qpst location ? . It must be for example on desktop in one folder . The simplest path is better . Don't use spacebar . Load content you must chose from that rom . Don't use other location . It's not necessary . Could you give some screenshots with qfil errors[/QUOTE
https://forum.xda-developers.com/attachment.php?attachmentid=4339940&stc=1&d=1511421690
https://forum.xda-developers.com/attachment.php?attachmentid=4339941&stc=1&d=1511421690
https://forum.xda-developers.com/attachment.php?attachmentid=4339942&stc=1&d=1511421690
Click to expand...
Click to collapse
I was trying to flash this Motorola RAZR D3 XT919 with MTK6577 chipset using latest (5.1924) SP Flash Tool with Windows 7.
Whenever I select the scatter file, I get a message about an older processor, and I'm told to use Flash Tool v5.1728 instead.
So I retry the operation with the suggested version 5.1728, and what happens? This processor is unsupported, please try with a newer SP Flash Tool version.
I tried all SPFT versions from 5.1728 to the 5.1844, and they feature the same messages: A newer version is required, until suddenly in certain version version 5.1728 is required. I even tried the version from the password-protected ZIP (?) in the SPFT website.
After this bad taste joke I switched to SP Flash Tool 3.1320, which does accept my MTK6577 scatter file. So I connect the phone switched off while pressing Vol (-) and it's recognized, but the Download process fails with this error: S_SECURITY_SLA_FAIL (6004). This was using the modified Mediatek USB VCOM driver shown in second screenshot.
I also attach error of flashing with RSD Lite, with the MTK Patch installed. I'm not sure if RSD Lite requires the standard Motorola driver or the modified driver, but I can't try anymore because the phone is in a worse state now. Currently Windows does not recognize it anymore, except for a few seconds if connected pressing Vol(+). This was probably after trying idiotic options from SPFT (read memory, etc) to see if something actually worked. Something did work, just to make it worse.
Any ideas or suggestions will be welcome. No idea how to perform a test point on this model, there are no references to be found online.
Hi,
Trying to install a ROM with fastboot (xiaomi 12.5.7.0) it seems something went wrong during the process.
So once the flash was done, device tried to reboot. All I got is a bleck screen with nothing happening.
Device is of course not detected by computer.
And of course nothing happens when I press the buttons.
Any idea or trick to help me out of this mess ?
Regards.
FRED
Here's some additional info :
if the device is hooked up to Windows, Windows plays a sound when it is hooked up.
And if I pressed the power button long enough, Windows plays like "on sound" and after some seconds a "off" sound.
So it does something...
Unbrick Xiaomi using miflash | Authorization EDL flash Xiaomi | Authorized Account
Unbrick Xiaomi using miflash | Authorization EDL flash Xiaomi | Authorized Account DOWNLOAD MODIFIED MIFLASH AND Qualcomm HS-USB QDLoader 9008 DRIVER The following actions : 1) Connect phone to pc in EDL mode 2) Open Miflash and specify the path to the firmware 3) Click on flash 4) A window...
xiaomi.eu
try this
I made a mistake while I was flashing a custom ROM PixelPlus UI in my device Redmi 9
after seccessfully flashing it I locked the bootloader and now my doesn't turn on either going in fastboot mood.I need help to fix it..plz plz plz
Hi, make sure that your battery is full, then hold VOl + and power key together and connect USB cable and see if is detected. The other things is to flash with edl mode but you need testpoint and flash tool like MRT... See over the internet for your model...
Vol+ and power key doesn't shows any sign.
Try then with VOl - and power but keep pressing and plug usb cable, if that doesn't work you need edl flashing....
Does edl supports in MTK processores?
Hi, sorry I mixed your device with Mi 9 model.... For MTK chipset you need BROM mode, so try to hold both VOL + and VOL - and plug usb cable and see if is detected... If it doesn't then send your device to nearby service center in order to flash with service box...
It shows something in ports......and few seconds later it goes away.
Good sign, then follow this flashing... use only if you have same chipset!
Mine is Mediatek G80 / MTK6769
Download Redmi 9 tested Flash File Firmware No Auth 100% Free
Download Redmi 9 tested Flash File Firmware No Auth Firmware Flash by using the SP Flash tool, 100% Free without Authorized MI account
romprovider.com
Do research....
i am trying but the port driver is still disconnecting...it doesnt stays stable
AlJabir001 said:
i am trying but the port driver is still disconnecting...it doesnt stays stable
Click to expand...
Click to collapse
Have your issue resolve and if so what exactly have you done, one of my friend done the same and facing the issue.
You are screwed if you locked the bootloader. Nothing you can do. At all.
AlJabir001 said:
i am trying but the port driver is still disconnecting...it doesnt stays stable
Click to expand...
Click to collapse
use the bypass_flashtool
bypass_flashtool_driver.rar
drive.google.com
YashxOS said:
bypass_flashtool_driver.rar
drive.google.com
Click to expand...
Click to collapse
go to bypass and run the brom.bat if on windows
conect the device it will regenizi it and force it to be stable
here a guide https://forum.xda-developers.com/t/...-etc-from-a-hard-brick.4535709/#post-87924847
YashxOS said:
here a guide https://forum.xda-developers.com/t/...-etc-from-a-hard-brick.4535709/#post-87924847
Click to expand...
Click to collapse
Thanks but issue has already been resolved using some tool provided on YouTube to unlock bootloader
navrkr said:
Thanks but issue has already been resolved using some tool provided on YouTube to unlock bootloader
Click to expand...
Click to collapse
oh ok when done put the [sovled]
Hello,
i brick my phone while doing a xiaomi update without recovery.
Actually, i'have no longer a Recovery, Fastboot, ...
I'have juste Bootloader and MTK.
I tried to use MTK with SP Flash Tool and Mtk bypass rev4 but no works
On launch flash, my phone has disconected from my pc.
I often have 3 mistakes :
ERROR: STATUS_DEVICE_CTRL_EXCEPTION (0xc0050001)
and
ERROR: STATUS_UNKNOWN_STORAGE_TYPE (0xC0040009)
and
Failed to get PMT info.
Do you know why it does this or do you have another solution to fix my phone?
PS: I'm not English, so sorry if there are any mistakes in my spelling
EDIT :
Have found the probleme, my usb port on the front of my pc don't work correctly,
I tried with the usb port on back of my pc and this WORK !!! (i'm happy )