Database Develop

Note 4 Hard Brick

necesito su ayuda mi note 4(N910T) se apago después de flashear custom rom estaba terminando de configurar cuando se apago y no volvió a encender no puedo entrar a modo download ni recovery espero me puedan ayudar

Google Translation:
I need your help my note 4 ( N910T ) will turn off after flashing custom ROM set was finishing when I went off and did not come to light can not enter download mode or recovery hope I can help
What did you use to flash the device originally? Did you use ODIN to flash the device originally?

Anonymously_Unknown said:
Google Translation:
I need your help my note 4 ( N910T ) will turn off after flashing custom ROM set was finishing when I went off and did not come to light can not enter download mode or recovery hope I can help
What did you use to flash the device originally? Did you use ODIN to flash the device originally?
Click to expand...
Click to collapse
Flash rom rom DrKetan was setting before completing the cel blinking LED in red as if he had finished the pile and not relit , can not go into any recovery mode or download and my pc recognizes nothing

It sounds as though your device will not need to be professionally JTAG'd to get it to boot at this point.

Anonymously_Unknown said:
It sounds as though your device will not need to be professionally JTAG'd to get it to boot at this point.
Click to expand...
Click to collapse
I can do As I JTAG tool but it tells me that is not compatible

HTC Desire 626s Bricked

Hi all, I write from Chile and I have a problem with my HTC Desire 626s (OPM9110) operator Claro Chile.
Unlocking bootloader and install TWRP recovery, but mistakenly erase the internal memory and stay briked. I failed to find a Nandroid backup, either custom rom, RUU Stock also failed to find as it is a Latin American smartphone
INFOkernel: lk
INFOproduct: htc_a32eul_la
INFOversion: 1.0
INFOimei: 35871806xxxxxxx
INFOversion-main: 1.11.598.3
INFOboot-mode: download
INFOversion-baseband: 01.01_U113251011_32.04.50622G_2
INFOversion-bootloader: 1.0.0.0000
INFOmid: 0PM911000
INFOcid: HTC__339
SD NOT MOUNTED
if not the correct section, apologize and move where appropriate

i would suggest see if u can find ruu for your modal here www.htc.com/us/support/rom-downloads.html , if the phone is totally bricked and wont turn on then u will i think need to disconect battery , if unable to take back to be fixed by place of purcahase and not able to get to fastboot due to bricking , then take back cover off , the battery connector isin top left corner of battery square removeing undercover to gain access to after removeing holding screws still felt more likley to breack phone so i cut top bar of under case to gain access to battery connector is simple push pull connector, once battery removed and no power to phone for some little tme after reconnecting is easy get acees to fastboot via power and vol down keys for 10sec remove vol down key after ten sec and u be in fastboot. all i can say is best of luck use a prise to lift that platic above circuit and cut if u want, if that is all is lost then nothing to loose. google replace screen to see what should be done but cut and bend is easiest if no refund is possible.
good luck
this is just suggestion and please dont blame me for any damage u may make to your phone is your call what to do
regards frankgambit

Hey there,
thanks for answering. I commented that the phone will install custom recovery (TWRP) and all well but has no operating system. In the link you point me no RUU for this version to be Latin American. Nor I encounter Custom Rom. I tried to find a Nandroid Backup but has gone wrong. I find nothing in this release and neither I can do S-OFF to change the CID and MID and put a RUU

TipoGT said:
Hey there,
thanks for answering. I commented that the phone will install custom recovery (TWRP) and all well but has no operating system. In the link you point me no RUU for this version to be Latin American. Nor I encounter Custom Rom. I tried to find a Nandroid Backup but has gone wrong. I find nothing in this release and neither I can do S-OFF to change the CID and MID and put a RUU
Click to expand...
Click to collapse
if u can get into fastboot mode then u only softbricked and can get unlock code from htcdev, once u unlocked bootloader then u can flash new boot and recovery signed imgs and then can restet your phone to factory settings. is howto unlock bootloader in this htc desire 626 forum and at htcdev, one thing to rem in cmd prompt when u click to mark text to copy for pasting enter pusts it into cashe so then when u paste u will paste what u highlighted in the cmd prompt.

already unlocked the bootloader but has original recovery. Instente and everything but I can only pass one RUU or a backup from another computer or ultimately a custom shape Custom Rom but can not find anything. In the internal memory is only the folder TWRP

well then u are soft bricked as if something working then is not hard bricked, i take it u have sdcard installed this should be easily accessed to install custom or stock rom .

frankgambit said:
well then u are soft bricked as if something working then is not hard bricked, i take it u have sdcard installed this should be easily accessed to install custom or stock rom .
Click to expand...
Click to collapse
I have not met and there is no custom rom for this RUU version

Apareció algo de esto? Tengo un problema, porque borré sin querer el laucher (Sense) y ahora el teléfono prende pero no veo los íconos ni puedo abrir las aplicaciones para seleccionar una. He probado de todo para poder restaurar la aplicación y no pasa nada. Alguien podría mandarme el .APK para ver si puedo instalarla con un APK Installer?
---------- Post added at 05:16 PM ---------- Previous post was at 05:09 PM ----------
O una RUU que sí pueda ser instalada, porque todas las que intento me fallan.

Restore from backup
You should be able to follow these steps to restore the TWRP Claro Backup available here:
1. Boot into TWRP Recovery
2. Backup your boot partition (DO NOT SKIP THIS STEP!)
3. Download the Claro TWRP Backup available here - https://www.dropbox.com/s/wn4y79efsrvwtwn/TWRP.rar?dl=0
4. Unrar the downloaded file
5. Copy the unrarred folder to your phone's internal storage at (\sdcard\TWRP\backups\<your random folder name here>)
6. Restore the Claro Backup
7. Wipe "Data", "Cache", "Dalvick Cache", and "Internal Storage" ONLY
8. Reboot phone

I'm Live in Chili too with the same problem
Not RUU latam enable in Internet, fastboot respond "command not found" in CEL, procedures to change CID not reconized for command fastboot, and another similar situation
Fortunately , my cel RUN ok but I want anyway goal my objetive to change android 6.0
I will see what happend with unplug battery procedure.
maybe I could bypass all problem changing the CID and this way RUU.exe from anothers company will run and will make the changes

twrp error ( failed to mount /persist (invalid argument) ) and bootloops

hello everyone i need help asap
i was running havoc and after a reboot i had bootloops and this error on twrp failed to mount /persist (invalid argument)
i tried everything i found on google but it still did not fix it
i tried to manually install persist.img but i cant do this cause i cant mount persist partition in twrp
i formatted data and installed other roms, bootloops again
finally if flashed with fastboot stock rom but again bootloop, this solution should be the fix but no
please any suggestions?

Use TWRP 3.3.1.0-0607 CN by wzsx150 to flash persist partition, can be downloaded at:
https://forum.xda-developers.com/showpost.php?p=79902192&postcount=111
It seems not only me got this problem, I tried many MIUI roms and the problem is happening over and over again.
- I use the phone for few days, then it couldn't wake up, and then boot loops.
- I was using the phone and then it hanged, and force reboot would lead into another boot loops.
Then I have to reflash the persist partition to fix the problem.

i have this problem too . and until now idk what cause /persist error .
just use TWRP from 2nd post . and flash persist.img only from MIUI .
then Format Data .

dasklney said:
Use TWRP 3.3.1.0-0607 CN by wzsx150 to flash persist partition, can be downloaded at:
https://forum.xda-developers.com/showpost.php?p=79902192&postcount=111
It seems not only me got this problem, I tried many MIUI roms and the problem is happening over and over again.
- I use the phone for few days, then it couldn't wake up, and then boot loops.
- I was using the phone and then it hanged, and force reboot would lead into another boot loops.
Then I have to reflash the persist partition to fix the problem.
Click to expand...
Click to collapse
kmzway000 said:
i have this problem too . and until now idk what cause /persist error .
just use TWRP from 2nd post . and flash persist.img only from MIUI .
then Format Data .
Click to expand...
Click to collapse
thank you so much finally solved it
as you said it randomly did that after a reboot
many years with different devices and i never had such a problem, was so weird to me

?
Dr.Dinel said:
thank you so much finally solved it
as you said it randomly did that after a reboot
many years with different devices and i never had such a problem, was so weird to me
Click to expand...
Click to collapse
how to flash?

Mr.Edu said:
how to flash?
Click to expand...
Click to collapse
Install the twrp that the other guy up posted
Pick the persist.img from every stock miui rom and restore it from twrp
If you need help post here

Dr.Dinel said:
Install the twrp that the other guy up posted
Pick the persist.img from every stock miui rom and restore it from twrp
If you need help post here
Click to expand...
Click to collapse
In miui rom for xiaomi redmi 6 cereus there is no persist.img file is only boot.img and I have error failed to mount '/ persist' (invalid argument) How to fix it?

burzaa4 said:
In miui rom for xiaomi redmi 6 cereus there is no persist.img file is only boot.img and I have error failed to mount '/ persist' (invalid argument) How to fix it?
Click to expand...
Click to collapse
Hey mate, I also have a redmi 6. Have you been able to do anything about persist.img?

kmzway000 said:
i have this problem too . and until now idk what cause /persist error .
just use TWRP from 2nd post . and flash persist.img only from MIUI .
then Format Data .
Click to expand...
Click to collapse
thanks

Dr.Dinel said:
ola a todos preciso de ajuda o mais rapido possivel
eu estava executando o havoc e após uma reinicialização eu tinha bootloops e este erro no twrp falhou ao montar / persistir (argumento inválido)
tentei de tudo que encontrei no google mas não resolveu
tentei instalar manualmente o persist.img, mas não consigo fazer isso porque não consigo montar a partição persist no twrp
formatei dados e instalei outras roms, bootloops novamente
finalmente, se flashado com fastboot stock rom, mas novamente bootloop, esta solução deve ser a correção, mas não
por favor alguma sugestão?
Click to expand...
Click to collapse
estou com esse problema . falha ao montar persist . no samsung galaxy S4 mini. pode me ajudar ?

Davidkrmc said:
estou com esse problema . falha ao montar persist . no samsung galaxy S4 mini. pode me ajudar ?
Click to expand...
Click to collapse
Please use English on XDA.
See
Galaxy S 4 Mini Q&A, Help & Troubleshooting
This forum is for all of your questions about the Samsung Galaxy S 4 Mini. If you need help troubleshooting a problem, please be as specific as possible by describing your software configuration, including the ROM, kernel, and any modifications you've done.
forum.xda-developers.com

i have same problem with redmi y2 , when i am wiping data it is showing failed to mount /'persist' (invalid argument)
please help trying find this solution but was not succesfull ,
how to recover from this error

dasklney said:
Use TWRP 3.3.1.0-0607 CN by wzsx150 to flash persist partition, can be downloaded at:
https://forum.xda-developers.com/showpost.php?p=79902192&postcount=111
It seems not only me got this problem, I tried many MIUI roms and the problem is happening over and over again.
- I use the phone for few days, then it couldn't wake up, and then boot loops.
- I was using the phone and then it hanged, and force reboot would lead into another boot loops.
Then I have to reflash the persist partition to fix the problem.
Click to expand...
Click to collapse
Sir i have a same problem also

Dr.Dinel said:
Install the twrp that the other guy up posted
Pick the persist.img from every stock miui rom and restore it from twrp
If you need help post here
Click to expand...
Click to collapse
Hello bro i m getting error of failed to mount persist and failed to mount cust invalid argument. When i try reboot to system it stucks on fastboot. How can i flash a ROM now bcz evertime i try to flash it shows failed to mount persist/cust. Please help me

dasklney said:
Use TWRP 3.3.1.0-0607 CN by wzsx150 to flash persist partition, can be downloaded at:
https://forum.xda-developers.com/showpost.php?p=79902192&postcount=111
It seems not only me got this problem, I tried many MIUI roms and the problem is happening over and over again.
- I use the phone for few days, then it couldn't wake up, and then boot loops.
- I was using the phone and then it hanged, and force reboot would lead into another boot loops.
Then I have to reflash the persist partition to fix the problem.
Click to expand...
Click to collapse
I am facing problem of failed to mount persist and cust so I can't able to flash a new rom and i accidentally deleted my earlier rom from device so now i am stuck on fastboot and device usb plugging is also off so tell me now what i can do to fix this issue.. plzz anyone help me

Flashing is not finishing mi flash tool(v.2018.11.15.0)

I tried to flash MI9T PRO fastboot rom on my k20pro. at first, i tried to flash the latest one (10.3.2.0) and it ended up with an error saying Missmatch in Device and IMAGE. after that, i tried to flash an older version (10.3.1.0) and it did not show any error but it's not finishing the flashing progress. i already tried refreshing , selecting again the flash folder and flash again but it did not stop the flashing progress. what should i do now? please help.
note that i use a Ryzen PC

Flashed Successfully
Finally, i could flash the latest fastboot rom successfully using this simple JAVA application "XiaomiADBFastbootTools.jar" within 2.5 min. i have attached the application UI and link. u may try it if you face the same problem using MI flash tool. Cheers !
Link : https://github.com/Saki-EU/XiaomiADBFastbootTools

zahidhasanzahid said:
Finally, i could flash the latest fastboot rom successfully using this simple JAVA application "XiaomiADBFastbootTools.jar" within 2.5 min. i have attached the application UI and link. u may try it if you face the same problem using MI flash tool. Cheers !
Link : https://github.com/Saki-EU/XiaomiADBFastbootTools
Click to expand...
Click to collapse
thank you, you save my life!
miflash is suck, always failed to flash with it...

zahidhasanzahid said:
Flashed Successfully
Finally, i could flash the latest fastboot rom successfully using this simple JAVA application "XiaomiADBFastbootTools.jar" within 2.5 min. i have attached the application UI and link. u may try it if you face the same problem using MI flash tool. Cheers !
Link : https://github.com/Saki-EU/XiaomiADBFastbootTools
Click to expand...
Click to collapse
Thanks a lot for the clue. Never tried it before although saw it earlier.
It's really great tool. Much better than miFlash Tool and also the progress is visible in the log.
Cheers.

zahidhasanzahid said:
Flashed Successfully
Finally, i could flash the latest fastboot rom successfully using this simple JAVA application "XiaomiADBFastbootTools.jar" within 2.5 min. i have attached the application UI and link. u may try it if you face the same problem using MI flash tool. Cheers !
Link : https://github.com/Saki-EU/XiaomiADBFastbootTools
Click to expand...
Click to collapse
I didn't know that this tool used flash stock. I always use it for debloat.
Thanks for sharing.

zahidhasanzahid said:
I tried to flash MI9T PRO fastboot rom on my k20pro. at first, i tried to flash the latest one (10.3.2.0) and it ended up with an error saying Missmatch in Device and IMAGE. after that, i tried to flash an older version (10.3.1.0) and it did not show any error but it's not finishing the flashing progress. i already tried refreshing , selecting again the flash folder and flash again but it did not stop the flashing progress. what should i do now? please help.
note that i use a Ryzen PC
Click to expand...
Click to collapse
Same thing is happening to me. I was trying to shift from Chinese ROM to Global in my Redmi Note AI. My phone turned on, already converted to Global, done Initial MIUI setup steps on the phone(selecting language, region, google account login...etc) but, in my PC MIFlashTool, it's still flashing, progress bar is green, no error is shown! should I unplug the USB and start using the phone as it is or re-flash using your Java tool?

why is my bootloader showing as locked even though i am on lineage. unable to use the jar for that reason.

alguém pode me ajudar? Eu coloquei meu celular pra instalar a rom, mas ele fica com o status em $pause. Gostaria de saber o que isso significa e se eu deveria esperar até algum resultado aparecer na tela.

Forum rules say posts must be in English.
This forum is for Mi 9T Pro / K20 Pro. Your screenshot shows you are flashing a Mi A3 ROM.
You are either posting in the wrong forum, or flashing the wrong ROM.

How to flash TWRP [Android 11, One UI 3.1] on Samsung A30 (SM-A305F/DS)

Hello everyone!
I have tried several times flashing TWRP with ODIN on my device (Samsung A30), but i get "fail" message on ODIN screen.
I have unlocked Developer Mode and checked OEM unlocking and USB debugging to be active.
Can someone have the time and will to give me a solution in few steps? I want to flash a custom rom after, so i would appreciate your time on responding me!
Regards!

I had this same problem of giving an error in the installation of TWRP, in fact, before installing TWRP, you have to install vbmeta, it is what blocks the installation of TWRP, install it and then install TWRP that will work, download vbmeta disabled, install in AP, then install TWRP and be happy

Thank you man! Going to, one last question, is it going to be flash-able with ODIN or do i need to use another installation method?
Thanks again for your quick response!

@Deivid Soltoski i got the same fail message even when tried to flash the vbmeta disabled...i guess its another way you install it not through ODIN...

alb.boy said:
@Deivid Soltoski i got the same fail message even when tried to flash the vbmeta disabled...i guess its another way you install it not through ODIN...
Click to expand...
Click to collapse
Show log...

And you write your message not there, there is a separate topic for questions

use twrp 3.4

alb.boy said:
Hello everyone!
I have tried several times flashing TWRP with ODIN on my device (Samsung A30), but i get "fail" message on ODIN screen.
I have unlocked Developer Mode and checked OEM unlocking and USB debugging to be active.
Can someone have the time and will to give me a solution in few steps? I want to flash a custom rom after, so i would appreciate your time on responding me!
Regards!
Click to expand...
Click to collapse
you need to unlock the bootloader and oem lock to able to flash modded firmware like twrp

alb.boy said:
@Deivid Soltoski recebi a mesma mensagem de falha mesmo quando tentei fazer o flash do vbmeta desabilitado...acho que é outra maneira de instalar não através do ODIN...
Click to expand...
Click to collapse
Oh no, but if you're having more problems, try downgrading to Android 10, which has fewer problems

tutibreaker said:
you need to unlock the bootloader and oem lock to able to flash modded firmware like twrp
Click to expand...
Click to collapse
I have done that through development mode. But still not working

alb.boy said:
I have done that through development mode. But still not working
Click to expand...
Click to collapse
No you dont, dude search for a guide here and read it

tutibreaker said:
No you dont, dude search for a guide here and read it
Click to expand...
Click to collapse
Will try, thanks though!