Related
i have a samsung galaxy note(GT-N7000) and it was working fine until
i accidentally flashed a samsung Galaxy SII STOCK firmware on it from Odin the flasing completed successfully but the device is with a black screen does not boot to download mode or recovery mode.
Please i need a solution
Have you tried a battery pull? Leave battery out of Note for about two-to-three minutes. Then try booting into recovery mode again?
Are you using volume up+ home then hold power until you get welcome screen for recovery?
If you have a backup from when you first got your note, try download mode - volume down + home then hold power until you get the welcome splash screen.
Still Not Working!!!
TempusFudgeIt said:
Have you tried a battery pull? Leave battery out of Note for about two-to-three minutes. Then try booting into recovery mode again?
Are you using volume up+ home then hold power until you get welcome screen for recovery?
If you have a backup from when you first got your note, try download mode - volume down + home then hold power until you get the welcome splash screen.
Click to expand...
Click to collapse
i tried but it will not boot at all no recovery mode no download mode
But it was working before i accidentally flash SII Firmware
is there a way to flash back the note firmware without going to download mode because the device will not boot
Help!!!
Please Reply Devolopers
While your Note is connected to PC Odin, try to get into download mode (vol down + home + power) then vol up, until you see there is connection in Odin (COM:ID turns yellow). Hopefully you still have 'life' there but just no screen/sound. Once you have that, flash a Note's firmware.
Sorry to say mate but your next and the only step is nearest samsung service center! :-(
BOOMED from my BOMBASTIC NOTE
betatest512 said:
i have a samsung galaxy note(GT-N7000) and it was working fine until
i accidentally flashed a samsung Galaxy SII STOCK firmware on it from Odin the flasing completed successfully but the device is with a black screen does not boot to download mode or recovery mode.
Please i need a solution
Click to expand...
Click to collapse
Please do this:
1. Replace battery
2. Insert batery
3. Hold down volume key + home key + power key for 15s to 20s
4. Press volume up key
5. Open Odin
6. connect your phone to pc
7. flash new bootloader(2.tar) by odin
Please see this link: http://forum.xda-developers.com/showthread.php?t=1354888
and download attachment file then extract it and choose 2.tar to flash.
After complete your phone can boot to download mod and you must flash original rom for galaxy note by download form www.sammobile.com
Good luck.
Wrong flash file
Happend to me to because av samfirmware´s system to list other phones firmware under the categorie "Latest Firmware" after searching for N7000....not good at all.
Of course i should have read more careful but after flashing cells since a few years back i did not think i could fall for that ;-)
So flashing the bootloader helped me back on track, got the screen back and started over with original fw. Thanks for the tip!
same problem here
i tried your answer. still no live on computer what should i do. phone is samsung galaxy note SHV-E160K
ysambo said:
Please do this:
1. Replace battery
2. Insert batery
3. Hold down volume key + home key + power key for 15s to 20s
4. Press volume up key
5. Open Odin
6. connect your phone to pc
7. flash new bootloader(2.tar) by odin
Please see this link: http://forum.xda-developers.com/showthread.php?t=1354888
and download attachment file then extract it and choose 2.tar to flash.
After complete your phone can boot to download mod and you must flash original rom for galaxy note by download form www.sammobile.com
Good luck.
Click to expand...
Click to collapse
ysambo said:
Please do this:
1. Replace battery
2. Insert batery
3. Hold down volume key + home key + power key for 15s to 20s
4. Press volume up key
5. Open Odin
6. connect your phone to pc
7. flash new bootloader(2.tar) by odin
Please see this link: http://forum.xda-developers.com/showthread.php?t=1354888
and download attachment file then extract it and choose 2.tar to flash.
After complete your phone can boot to download mod and you must flash original rom for galaxy note by download form www.sammobile.com
Good luck.
Click to expand...
Click to collapse
Thanks i found this... i've managed to get the download mode back and restore original firmware.. thanks bro :good:
lentzit said:
Happend to me to because av samfirmware´s system to list other phones firmware under the categorie "Latest Firmware" after searching for N7000....not good at all.
Of course i should have read more careful but after flashing cells since a few years back i did not think i could fall for that
So flashing the bootloader helped me back on track, got the screen back and started over with original fw. Thanks for the tip!
Click to expand...
Click to collapse
Yeahh me too, has the same problem and solved it
ysambo said:
Please do this:
1. Replace battery
2. Insert batery
3. Hold down volume key + home key + power key for 15s to 20s
4. Press volume up key
5. Open Odin
6. connect your phone to pc
7. flash new bootloader(2.tar) by odin
Please see this link: http://forum.xda-developers.com/showthread.php?t=1354888
and download attachment file then extract it and choose 2.tar to flash.
After complete your phone can boot to download mod and you must flash original rom for galaxy note by download form www.sammobile.com
Good luck.
Click to expand...
Click to collapse
Wow dude.
This worked for me to.
I wanted to flash a Rom but it did not work.
So i flashed back to stock Rom that i downloaded from sammobile.
This resulted in a black screen. Flashed a earlier version...still black screen.
But i noticed that the phone worked normally accept the screen was black.
I tried a few thing's until i found this. Genius!
Thanks for sharing dude.
Hmm i tried the steps mentioned, I think i managed to flash the original n7000 firmware and rom, but unfortunately i still see black screen. I can hear the starting tone of samsung while booting up thought, so my system is still working, jz the screen is not. Oh boy, could that be hardware issue then? Anyone knows how to check?
(DISCONTINNUED
This TWRP is only for Speadtrum 3G!!!!
Hi folks!
Finally we have a twrp for your Sm-j120H Spreatrum that works! Here's the link:
Root SM-J120H working.rar
http://www20.zippyshare.com/v/XmD4XuEW/file.html
If you want to test (do it for your own risk)!
STEPS:
1 - Unzip file on your computer;
2 - Open Odin folder and copy the supersu zip file to your internal memory (without unzip it);
3 - Open Odin (double click on blue icon);
4 - Click on "AP" icon and select the twrp tar file on Odin folder (j1 (6).tar);
5 - Turn on "Unlock OEM" and "USB Debugging" on Delevoper Options (Actvating Delevoper Options: seven clicks on Build Number - Software Info);
6 - Turn off your phone and turn on again holding Volume Down + Home Button + Power Button (Download Mode). When a screen with some texts appears, release all buttons and press Volume Up again to activate the Download Mode;
7 - After this, connect your phone to your computer and click Start on Odin. Wait until your device restarts;
8 - Disconnect your phone to your computer and turn it off. Turn it on holding Volume Up + Home Button + Power Button (Recovery Mode). When your phone vibrates and appears J1 6 logo, release all buttons. If worked, TWRp will starts;
9 - Select the language, click on Read Only and the TWRP starts. After this, click on Install and search The Supersu zip you copied. Click on it and drag the flash file. Wait finish it. Restart the system. Done!
Credits: Aldous Cariño (Galaxy J1 Edition Phillipines Facebook Group - (https://www.facebook.com/groups/SamsungGalaxyJ12016EditionGroupPhilippines/)
IMPORTANT!!!!!!
This twrp was tested and worked on brazilian devices. Others had some problems. Test it and comment your feedback here!
If you are a developer and interests to work on this file, but doesn't have the device, i'll be glad to help being your beta tester!!!!
If you need the stock rom, download it from this site: https://samsung-firmware.org/model/SM-J120H/
Thanks!
I tried this on a SM-J120M from Colombia.
Recocvery flashed OK, phone rebooted.
Turned it off, tried to enter recovery, android robot appears "installing system update" or something like that.
After a few seconds, standard recovery appears and not TWRP.
So I figured that the stock rom somehow replaces the custom recovery at first boot.
Flashed again but after Odin finished, I pulled the battery at once.
Tried again to enter recovery, this time a red text above the J1 logo shows "Recovery is not seandroid enforcing"
Pulled the battery again and turned on, phone booted normally, but twrp recovery was again replaced with standard recovery.
I'm on the latest firmware and this phone until now can not be rooted and no custom recovery seems to be available.
Somehow "knox" was set to 1 in the process, meaning warranty void.
Cheers.
Well, this has been tackled finally
Key issue was the right TWRP recovery.
Someone on Youtube posted the instructions and files titled: RECOVERY TWRP PARA SAMSUNG J1 2016 (TODAS LAS VERSIONES)
This time the TWRP recovery did work, after that I flashed the SuperSu from TWRP and all was finished.
Next I'll be looking for a custom rom, but so far very happy with the results.
Cheers.
escorpiompom said:
Well, this has been tackled finally
Key issue was the right TWRP recovery.
Someone on Youtube posted the instructions and files titled: RECOVERY TWRP PARA SAMSUNG J1 2016 (TODAS LAS VERSIONES)
This time the TWRP recovery did work, after that I flashed the SuperSu from TWRP and all was finished.
Next I'll be looking for a custom rom, but so far very happy with the results.
Cheers.
Click to expand...
Click to collapse
Hello,
Could I have a link to the files that work for the J120M? I have the same phone and I think I found what you're talking about but I have the same issue with the stock recovery showing up instead.
Thanks!
EDIT: Actually, do I need to use TWRP? Can't I just "install update from external storage" with the stock bootloader?
Sure, I didn't post the link because it may not be allowed on this board (for newbies like me).
If you just put that title in Youtube it shows as the first result.
Anyway, here is the direct link for all the files:
Code:
https://www.datafilehost.com/d/296cd14c
Disable the download manager that is checked by default.
Use odin to flash TWRP, disable auto reboot and after flashing enter recovery at once with vol up+home+power buttons.
You may get a warning in red about recovery not enforcing blaba, just wait until TWRP shows and release the buttons.
It's not possible to flash SuperSU from stock recovery, you need a custom recovery like TWRP.
I couldn't find CWM for this phone, but anyway I like TWRP more.
Cheers.
escorpiompom said:
Sure, I didn't post the link because it may not be allowed on this board (for newbies like me).
If you just put that title in Youtube it shows as the first result.
Anyway, here is the direct link for all the files:
Code:
Disable the download manager that is checked by default.
Use odin to flash TWRP, disable auto reboot and after flashing enter recovery at once with vol up+home+power buttons.
You may get a warning in red about recovery not enforcing blaba, just wait until TWRP shows and release the buttons.
It's not possible to flash SuperSU from stock recovery, you need a custom recovery like TWRP.
I couldn't find CWM for this phone, but anyway I like TWRP more.
Cheers.
Click to expand...
Click to collapse
Ahh, thanks! As it turns out I did find the correct link, but the trick was to immediately enter into recovery mode after flashing without letting the phone fully boot first. Got my phone rooted now, thanks a bunch!
This method workin on 100%/ Thanks!
amebablues said:
Hi folks!
Finally we have a twrp for your Sm-j120H Spreatrum that works! Here's the link:
Root SM-J120H working.rar
http://www20.zippyshare.com/v/XmD4XuEW/file.html
If you want to test (do it for your own risk)!
STEPS:
1 - Unzip file on your computer;
2 - Open Odin folder and copy the supersu zip file to your internal memory (without unzip it);
3 - Open Odin (double click on blue icon);
4 - Click on "AP" icon and select the twrp tar file on Odin folder (j1 (6).tar);
5 - Turn on "Unlock OEM" and "USB Debugging" on Delevoper Options (Actvating Delevoper Options: seven clicks on Build Number - Software Info);
6 - Turn off your phone and turn on again holding Volume Down + Home Button + Power Button (Download Mode). When a screen with some texts appears, release all buttons and press Volume Up again to activate the Download Mode;
7 - After this, connect your phone to your computer and click Start on Odin. Wait until your device restarts;
8 - Disconnect your phone to your computer and turn it off. Turn it on holding Volume Up + Home Button + Power Button (Recovery Mode). When your phone vibrates and appears J1 6 logo, release all buttons. If worked, TWRp will starts;
9 - Select the language, click on Read Only and the TWRP starts. After this, click on Install and search The Supersu zip you copied. Click on it and drag the flash file. Wait finish it. Restart the system. Done!
Credits: Aldous Cariño (Galaxy J1 Edition Phillipines Facebook Group - (https://www.facebook.com/groups/SamsungGalaxyJ12016EditionGroupPhilippines/)
IMPORTANT!!!!!!
This twrp was tested and worked on brazilian devices. Others had some problems. Test it and comment your feedback here!
If you are a developer and interests to work on this file, but doesn't have the device, i'll be glad to help being your beta tester!!!!
If you need the stock rom, download it from this site: https://samsung-firmware.org/model/SM-J120H/
Thanks!
Click to expand...
Click to collapse
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
anitamobile said:
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
Click to expand...
Click to collapse
This file is for Spreadtrum 3G devices. OTG not working at all. FOr ext card, try to wipe data and cache after install and reboot.
tried it on my SM-J120G, but failed .. all steps completed but when i started the phone in recovery mod, it got stuck at j1 2016 logo and a message in red fonts saying ''RECOVERY IS NOT SEANDROID ENFORCING''. After i just tried to switch off and on, but the screen dosent respond. After holding all physical button, vol up-dn, power and home, it got restarted in normal mode.
device tree
please give me device tree of this device .. please
Does it works in sm-j120G??
anitamobile said:
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
Click to expand...
Click to collapse
The problem has been resolved
new recovery twrp :fingers-crossed:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
---------- Post added at 12:11 AM ---------- Previous post was at 12:06 AM ----------
amebablues said:
This file is for Spreadtrum 3G devices. OTG not working at all. FOr ext card, try to wipe data and cache after install and reboot.
Click to expand...
Click to collapse
The problem has been resolved :good:
new TWRP :highfive:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
Project Discotinnued
Sorry taking too long to answer...I'm not using this device anymore. Maybe this link help you: https://github.com/joenka/android_device_j120h
Best regards
shugash said:
Does it works in sm-j120G??
Click to expand...
Click to collapse
Not testing. If you waana try, do it your risk.
syria-droid said:
The problem has been resolved
new recovery twrp :fingers-crossed:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
---------- Post added at 12:11 AM ---------- Previous post was at 12:06 AM ----------
The problem has been resolved :good:
new TWRP :highfive:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
Click to expand...
Click to collapse
Ok. But your device is Speadtrum 3G? This twrp is for this model.
amebablues said:
Ok. But your device is Speadtrum 3G? This twrp is for this model.
Click to expand...
Click to collapse
I know
the problem Present in all phones model (j120h)
Rooted j120g
Bro I have rooted my j120g
Want to know how to root contact me bro
[email protected] or fb id skrillex cario
Hai is it possible to flash stock 120g firmware on 120h ? Please reply
Help me to Root my Samsung Galaxy J1 (2016) SM-J120H
Sir I really need your help. What is the first thing to do before going into Rooting method? Do I need to backup any Files or what? Thnak you. Guide me please. Thank You
My Tab S2 T713 is currently running the latest stock Samsung rom. I want to install Lineage 15.1
I've downloaded twrp-3.2.1-0-gts28vewifi.img.tar & Odin 3.12.7. I can boot into download mode, flash TWRP with Odin which says success & my tablet reboots normally. When I power down & reboot into recovery TWRP gets over written by the stock recovery.
If I uncheck Auto Reboot in Odin, after flashing success, I'm still in download mode - I've read that I need to boot directly into recovery from download mode - how do I do this?
In download mode pressing home + voldown + power reboots normally. Pressing home + volup + power does nothing
What am I doing wrong?
Gidders said:
My Tab S2 T713 is currently running the latest stock Samsung rom. I want to install Lineage 15.1
I've downloaded twrp-3.2.1-0-gts28vewifi.img.tar & Odin 3.12.7. I can boot into download mode, flash TWRP with Odin which says success & my tablet reboots normally. When I power down & reboot into recovery TWRP gets over written by the stock recovery.
If I uncheck Auto Reboot in Odin, after flashing success, I'm still in download mode - I've read that I need to boot directly into recovery from download mode - how do I do this?
In download mode pressing home + voldown + power reboots normally. Pressing home + volup + power does nothing
What am I doing wrong?
Click to expand...
Click to collapse
https://forum.xda-developers.com/tab-s2/development/twrp-3-0-2-1-galaxy-tab-s22016-sm-t713-t3390627
Instructions:
Flash with ODIN 3.10.7 in the AP slot.
Put your device in DOWNLOAD mode.
Uncheck Auto reboot.
Load the respective file below into the AP slot and hit start.
After flashing and ODIN reports PASS immediately reboot to recovery by holding POWER + HOME + VOL DOWN.
As soon as the screen goes blank change to VOL UP whilst still holding POWER + HOME.
You should now see TWRP recovery.
Brilliant - thank you. Why they can't have they have that in the Lineage install instructions?
Now running Lineage 15.1 = happy bunny
boxcar8028 said:
https://forum.xda-developers.com/tab-s2/development/twrp-3-0-2-1-galaxy-tab-s22016-sm-t713-t3390627
Instructions:
Flash with ODIN 3.10.7 in the AP slot.
Put your device in DOWNLOAD mode.
Uncheck Auto reboot.
Load the respective file below into the AP slot and hit start.
After flashing and ODIN reports PASS immediately reboot to recovery by holding POWER + HOME + VOL DOWN.
As soon as the screen goes blank change to VOL UP whilst still holding POWER + HOME.
You should now see TWRP recovery.
Click to expand...
Click to collapse
For the love of god, thank you. This wasn't in the LineageOS instructions. But I still can't install it, it says my bootloader isn't supported (T713XXU1APG1).
notmyidea said:
For the love of god, thank you. This wasn't in the LineageOS instructions. But I still can't install it, it says my bootloader isn't supported (T713XXU1APG1).
Click to expand...
Click to collapse
Did you go into your developer settings and make sure you toggled the option titled "OEM Unlock"?
sh0nuff said:
Did you go into your developer settings and make sure you toggled the option titled "OEM Unlock"?
Click to expand...
Click to collapse
Got that figured out, thanks. All installed now after much difficulty.
notmyidea said:
Got that figured out, thanks. All installed now after much difficulty.
Click to expand...
Click to collapse
Good to hear! Please make sure you give a thumbs up to anyone who helped. It really keeps the community alive and kicking!
I found that I had to do this from completely powered off state:
press home + volume up + power
wait until second "sentence" appears on screen in yellow (the first "sentence" is blue),
Then release all buttons
twrp now boots.
for some reason, my internal and external storage is showing 0 mb. Anyway to fix this?
Try formatting (not just wipe) data.
Should the Galaxy Tab S2 2016 be on TWRP 3.2.1.0 or the new 3.2.3.0 for Linage OS 15?
If so, can't you just flash the update using TWRP on the img file, or is ODIN on the tar needed?
OK, I updated to TWRP 3.2.3 using TWRP Recovery and the img file. Appears to work fine.
SvenHee said:
I found that I had to do this from completely powered off state:
press home + volume up + power
wait until second "sentence" appears on screen in yellow (the first "sentence" is blue),
Then release all buttons
twrp now boots.
Click to expand...
Click to collapse
Sorry to revisit this issue. I can't get TWRP going on my S2 Tablet. I understand these instructions, but at the end of the ODIN installation there are two possibilities that I can see. If you set the ODIN to automatically reboot then you cannot do the above because it says to do it from completely powered off.
If you don't set ODIN to reboot automatically I can't get the tablet to turn off. I can only get it to boot by holding home+volume down + power. How do I get the tablet to power off before booting??
I am using ODIN 3.14.4 and TWRP-3.7.0 9-0-gts28wifi.img.tar and my stock firmware is NRD90M.T713XXS2BSG1 with Kernel 3.10.84-14953299
Thank you.
Warning:
Proceed with your own risk. I hold no responsibility if something goes wrong and you get killed.
Warranty void
KNOX tripped and some security feature won't be available
This guide based on @topjohnwu Magisk for Samsung. However, T510 is a bit different because it doesn't have Bixby button.
https://topjohnwu.github.io/Magisk/samsung
You need the latest Odin (I use 3.13). 3.12 or older won't work
***** NOTICE *****
Auto reboot must be disabled.
Download ROM matches your build number especially the last three characters. Unzip and only use AP and copy it to your tablet
Download ***special*** version Magisk Manager to your tablet and install it. "Install" Magisk using patch boot with AP file, and copy magisk_patched.tar to your host PC
https://raw.githubusercontent.com/topjohnwu/magisk_files/master/canary_builds/app-release.apk
Do not use normal Magisk to patch AP because it won't work
Bootloader Unlocked (read my guide)
Do not restore yet until this process is done.
STEPS:
1. Download your version of ROM. Make sure it matches your device Build Number
2. Unzip the ROM and copy AP to your tablet. Install Magisk Manager downloaded from link above. Normal Magisk Manager won't work.
3. Patch AP with Magisk Manager. The output file is "magisk_patched.tar". Copy the output file to your host computer.
4. Open Odin. Make sure Auto Reboot is disabled (unchecked)
5. Turn your tablet off. Press and hold Volume up and down buttons and connect your tablet to host computer. Press Volume up again to enter Download Mode.
6. Odin should show "Added". Locate your "magisk_patched.tar" and open as AP (it's AP after all). You don't have to flash others.
7. Wipe your tablet.
Disconnect your tablet.
Press and hold Power and Volume down.
As soon as the screen goes dark, immediately press and hold Power and Volume up until recovery screen appears.
Choose Factory Reset and press Power once, and confirm.
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
9. Do initial setup. Copy the Magisk Manager to your tablet and install if you don't see it
10. Setup internet connection and Magisk Manager will do some process, and it will reboot after it's done. You don't have to do button combo at this time.
11. Open Magisk Manager again to add other function including hide.
Your tablet should be rooted. However, here is something you should know.
Press Power button only: System with Magisk
[*]Press and hold Power and Volume up buttons before the screen shows bootloader warning and release: System with Magisk
Press and hold Power and Volume up buttons all the way: Stock recovery
That's it. Root is done.
***** IMPORTANT *****
If you want to do manual update, make sure you do steps 1-6 again. You don't have to wipe your tablet however.
Update: it appears "normal" Magisk (19.3) and Magisk Manager can simplify the entire rooting process.
Special instructions for Samsung is gone now.
Moreover, it appears normal boot can enter rooted system without button combo
mingkee said:
However, here is something you should know.
Press Power button only: System with no Magisk
Press and hold Power and Volume up buttons before the screen shows bootloader warning and release: System with Magisk
Press and hold Power and Volume up buttons all the way: Stock recovery
That's it. Root is done.
Click to expand...
Click to collapse
I must not be understanding something, as no matter how I press Power and Volume Up, I end-up in recovery. Otherwise it boots without magisk installed.
If I release buttons when I see the Samsung logo, before the warning, I can then press volume up to continue with boot, and it opens recovery.
If I release buttons after I see the warning, the warning goes away in a flash and I still end-up in recovery.
If I release the buttons as soon as I see the Samsung logo, same thing.
Any suggestions?
I did all the steps again, strangely Magisk gave me a different patched.tar file.
Flashed the patched, but I noticed in Odin:
<ID:0/008> recovery.img
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I get a red message saying only official release binaries... The tablet is unlocked though... I must be missing something.
EDIT:
Now the tablet says an error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software. Can't even turn it off!
Smart Switch says 'Unsupported device' and device does not appear in the list for emergency recovery. Tablet appears soft-bricked
Finally Odin managed to flash it, after failing at first. Flashing stock now. Will start over.
It appears the latest Magisk and Manager simplified everything.
The latest Magisk (19.3) is "normal" version, so you may no longer need "canary". Moreover, special instructions for Samsung disappeared (click the link on the first post and it doesn't work).
I also noticed normal boot (just press power button with no combo) and boot into "root mode"
mingkee said:
It appears the latest Magisk and Manager simplified everything.
The latest Magisk (19.3) is "normal" version, so you may no longer need "canary". Moreover, special instructions for Samsung disappeared (click the link on the first post and it doesn't work).
I also noticed normal boot (just press power button with no combo) and boot into "root mode"
Click to expand...
Click to collapse
I followed the original guide and using the button combo to boot with Magisk. How do I move to normal boot? Magisk installed version is 19.4-c, and I just received version 7.3.0 of the manager. Should I simply (re-)install Magisk 19.4-c to get normal boot?
3c said:
I followed the original guide and using the button combo to boot with Magisk. How do I move to normal boot? Magisk installed version is 19.4-c, and I just received version 7.3.0 of the manager. Should I simply (re-)install Magisk 19.4-c to get normal boot?
Click to expand...
Click to collapse
I will show you a screen cap later on because I don't carry it to work.
I used the "canary" build Manager and the root.zip
Now the root.zip is normal while Manager build number is still different.
As I mentioned on the edited post, the special instructions is gone, so it's possible topjohn has figured out solution for Samsung and integrated.
Yes, I boot it "normal" way and root is 100%
Noob Question
Hello and thanks for that guide!
There is (at least for now) one question:
Where do I get the stock ROM from?
mingkee said:
Warning:
STEPS:
1. Download your version of ROM. Make sure it matches your device Build Number
Click to expand...
Click to collapse
LeonardHofstadter said:
Hello and thanks for that guide!
There is (at least for now) one question:
Where do I get the stock ROM from?
Click to expand...
Click to collapse
You can find them on sammobile or samfrew
Thanks for this guide but I think I didn't do something right.
----------------
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
----------------
At this part, just after the factory reset, I reboot system and then I press Power and Vol+, but it goes again to Recovery. It never reboots like "brand new unit". It will always show the warning at start. Perhaps I misunderstood this part somehow.
Hantoniorl said:
Thanks for this guide but I think I didn't do something right.
----------------
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
----------------
At this part, just after the factory reset, I reboot system and then I press Power and Vol+, but it goes again to Recovery. It never reboots like "brand new unit". It will always show the warning at start. Perhaps I misunderstood this part somehow.
Click to expand...
Click to collapse
When you press Power and Vol+ the warning will only flash, that's when you need to release the buttons. If you keep pressing it goes in recovery. I had a hard time figuring this out.
3c said:
When you press Power and Vol+ the warning will only flash, that's when you need to release the buttons. If you keep pressing it goes in recovery. I had a hard time figuring this out.
Click to expand...
Click to collapse
Thanks!
I just tried releasing the buttons just afther the "warning flash". Then it showed up again. After initial settings and Magisk installation, again that screen.
I'll try to start from scratch with another T510 and report back as soon as I can. Thanks again.
I'm pretty sure rebooting to recovery with volume up and power is still needed on every boot. The link for Samsung devices has just been moved.
https://topjohnwu.github.io/Magisk/install.html#samsung-system-as-root
Thanks for the guide.
Can someone confirm if i reboot, what do i have to press to keep it in root mode.?
So far the only way I've been able to do it, is to press power and volume up button and release when it flashes.
Root keeps disappearing unless I press combination of buttons.
Is there anyway to keep in root mode without pressing buttons?
test2006au said:
Thanks for the guide.
Can someone confirm if i reboot, what do i have to press to keep it in root mode.?
So far the only way I've been able to do it, is to press power and volume up button and release when it flashes.
Root keeps disappearing unless I press combination of buttons.
Is there anyway to keep in root mode without pressing buttons?
Click to expand...
Click to collapse
I believe this is the only method at the moment.
Thank you very much for the rooting method, after unlocking the bootlader and rooting I have expanded my ram and now my tablet works flawlessly
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Triscuit said:
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Click to expand...
Click to collapse
Sent from my Pixel 2 XL using XDA Labs
Hey there, thank you for your guide!
I had a little problem when flashing with Odin though.
The tablet starts downloading, but when it gets to vbmeta.img, it shows the error "Custom Binary(VBMETA) Blocked by OEM Lock"
Before flashing, I disabled OEM Lock in the Developer Settings, but it did not help.
Any ideas would be greatly appreciated. Thx again!
Triscuit said:
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Click to expand...
Click to collapse
I'm hitting a roadblock here, as well. I haven't tried using JOdin because I've seen discussions stating that you need 1.4.2 of Heimdall to flash these tablets, so I built that from source (JOdin includes 1.4.0). I unlocked the tablet, then patched the firmware with Magisk. Now I'm not sure what to do next.
Heimdall has its own package structure (which I'll read tonight), so it won't flash the AP file like Odin. It looks like it requires individually flashing each segment of the AP archive directly, and I really don't want to do that without some input from someone who can confirm that will work.
I'm acting based on this thread, on [RECOVERY][UNOFFICIAL] TWRP 3.3.1 for 2019 Galaxy Tab A 10.1 [SM-T510] and the Magisk install by patching file instructions.
Do I really need to extract each piece of the TAR per these instructions?
Also, the instructions to install TWRP here don't state that rooting must be done first, but based on the whole workflow, it seems it is required because this process flashes to AP and Magisk uses a stock AP when patching. It seems the work for TWRP would be obliterated by the Magisk root process.
Can anybody clear this up?
Kenaz Rune said:
I'm hitting a roadblock here, as well. I haven't tried using JOdin because I've seen discussions stating that you need 1.4.2 of Heimdall to flash these tablets, so I built that from source (JOdin includes 1.4.0). I unlocked the tablet, then patched the firmware with Magisk. Now I'm not sure what to do next.
Heimdall has its own package structure (which I'll read tonight), so it won't flash the AP file like Odin. It looks like it requires individually flashing each segment of the AP archive directly, and I really don't want to do that without some input from someone who can confirm that will work.
I'm acting based on this thread, on [RECOVERY][UNOFFICIAL] TWRP 3.3.1 for 2019 Galaxy Tab A 10.1 [SM-T510] and the Magisk install by patching file instructions.
Do I really need to extract each piece of the TAR per these instructions?
Also, the instructions to install TWRP here don't state that rooting must be done first, but based on the whole workflow, it seems it is required because this process flashes to AP and Magisk uses a stock AP when patching. It seems the work for TWRP would be obliterated by the Magisk root process.
Can anybody clear this up?
Click to expand...
Click to collapse
I honestly gave up trying to do this whole process on Linux, so I made a virtual machine with windows, made sure all my USB stuff was correct and used the official ODIN, worked like a charm
Sent from my Pixel 2 XL using XDA Labs
Hi guys while searching the web and the forum to find a way to root our phone I found this guide https://topjohnwu.github.io/Magisk/samsung
you can do it by yourself if you want but I thought to edit it a bit to match our device. all credit goes to original developer I just copied what he did and it worked.
I don't take any responsibility if anything happens to device, brick ect. use the guide with your own risk!
make sure you have updated drivers and a good usb cable, I recommend Smart Switch for pc you can download in the samsung site, it will also install latest drivers and you can back up the phone with it to the pc.
just for your information rooting voids the waranty, trips knox and makes things complicated, but I can't have a phone without root, it reminds me the days with my old nexus 4.
this guide will also factory reset your phone so make sure to back up everything don't forget to back up whatsapp in the app itself.
I'm not a developer maybe there is an easier way to root, this is the only way I found, so if you want to wait until an experienced developer who knows english better then me release another way to root that's fine by me, I wont get upset.
the only downside I see in this kind of root that you can't normally enter the system. I mean that normal reboot and power up will boot your system without magisk, because the root sits on the recovery or something like that. so each time you power off your phone to power it up you need to hold the Volume up + Power button untill you see the bootloader unlocked warning and release, and everything will be working with root. even if you accidently powerd your phone without the way I mentioned you still have root don't panic like I did just turn off the phone and power it up like I mentioned and its all good.
also you can't normally update the phone through the phone settings and to update the phone with odin like I understand you'll need to have a patched version of the AP tar file with magisk, or something bad will happen to the phone, again I am not a developer I don't know the full risks.
so after the warnings and the long intro here is the edited guide:
Unlock the bootloader - this will wipe all your data so make sure to back up before you start anything!
Allow bootloader unlocking in Developer options → OEM unlocking
Power off your device. Volume Up + Volume Down + Power button and plug in your device to a PC to boot into download mode
Long press volume up to unlock the bootloader. This will wipe your data and automatically reboot.
the developer also mentions that sometimes it wont work because something called VaultKeeper. I didn't had that issue just make sure after the system boots after you unlocked the bootloader that the OEM unlocking option exists and grayed out in the developer options.
Instruction
1.Download the firmware for your device.
2.Unzip the firmware and copy the AP tar file to your device. It is normally named as AP_[device_model_sw_ver].tar.md5
3.Install Magisk Manager from the Canary Channel
4.In Magisk Manager: Install → Install → Select and Patch a File
5.Select the AP tar file. Magisk Manager will patch the whole firmware file and store the output to [Internal Storage]/Download/magisk_patched.tar
6.Copy the tar file to your PC, and boot your device to download mode. (Hold all 3 buttons Volume Up+Volume Down+Power Button and connect to PC cable)
I have downloaded the firmware with Samfirm I found it on the forum I'll upload it here. I will also upload the AP file I patched and write the firmware version I took it from. I'll also upload the full firmware for you if you can't find a good mirror online. and also the odin version I used.
the csc i look up is for ILO but I think the csc have multiple regions, you know better I'll upload it anyway maybe it will save time for someone.
7.Flash magisk_patched.tar as AP in ODIN (I flashed the entire firmware because I had some problems flashing without all the files try it the way you want. flash it with normal csc of you choose to flash the whol firmware)
Important: Uncheck “Auto Reboot” in Options!!!!
8.Magisk is now successfully flashed to your device! But there are still several steps before you can properly use the device.
9.We now want to boot into the stock recovery to factory reset our device.
Full data wipe is mandatory! Do not skip this step.
Press Power Button+Volume Up+Volume Down to exit download mode, and as soon as the screen turns off, immediately press Power Button+Volume Up to boot to recovery partition. Just as mentioned in the previous section, since we want to boot into stock recovery, continue pressing the volume up button until you see the stock recovery screen.
10.In the stock recovery menu, use volume buttons to navigate through menus, and the power button to select the option. Select Wipe data/factory reset to wipe the data of the device.
11.This time, we can finally boot to the system with Magisk. Select Reboot system now, and immediately press Power Button+ Volume Up. After seeing the bootloader warning screen, release all buttons so it can boot to the system.
12.The device will automatically reboot for the first time it boots. This is completely normal and done by design.
13.After the device is booted up, do the usual initial setup. The following steps will need internet connection.
14.You shall see Magisk Manager in your app drawer; if not, manually install the APK you downloaded in step 3 and continue to the next step. The app would be a stub and it shall automatically upgrade to the full Magisk Manager when you open it.
15.Magisk Manager will ask to do additional setups. Let it do its job and the app will automatically reboot your device.
16.Baruh Ashem! enjoy magsik!
That's it I think if I forgot something I'm sorry I hope it worked for you! and maybe some real developers start to look at the device and start building costume roms andall the good stuff that comes with it!
meanwhile the files are uploading you can try get them by yourself here are the names of the files I used:
Odin3_v3.13.1_3B_PatcheD
Samfirm
firmware file: SM-A705FN_1_20190412140953_u5ql0uali6_fac
Magisk manager is linked the developer enterd the canary build but I'll also upload 7.1.2.apk version I found on the internet.
ALL CREDIT GOES TO THE ORIGINAL DEVELOPER, AND DEVELOPERS. if you have any question I can help you with my own expirence only.
Here is the download link, use at your own risk. if you are not sure the firmware uploaded is right for your device download yourself with samfirm that i also uploaded.
Download Link - Google Drive
Thanks for your research and this manual! I've been trying your steps for a few hours now, and after a few trial and errors, softbricks and reboots I'm still not able to succeed.
Magisk Manager won't show up in the apps after setup wizard. Installing it manually, it says Magisk is not installed
My phone: A70 from the Netherlands. I used Israel firmware from updato.com (https://updato.com/firmware-archive-select-model?record=440E12D670B911E9BE8CFA163EE8F90B) and your file (which is same size after patching). Unfortunately I can't find Dutch firmware, hence the Israel version.
Anybody else succeeded?
Captain Beretta said:
Thanks for your research and this manual! I've been trying your steps for a few hours now, and after a few trial and errors, softbricks and reboots I'm still not able to succeed.
Magisk Manager won't show up in the apps after setup wizard. Installing it manually, it says Magisk is not installed
My phone: A70 from the Netherlands. I used Israel firmware from updato.com (https://updato.com/firmware-archive-select-model?record=440E12D670B911E9BE8CFA163EE8F90B) and your file (which is same size after patching). Unfortunately I can't find Dutch firmware, hence the Israel version.
Anybody else succeeded?
Click to expand...
Click to collapse
thank you for the feedback!
did you flashed the whole firmware? with BL, patched AP,CP and CSC? on the google drive folder I have to full firmware try to download that.
maybe you do have it installed but you didn't boot corectly. try to turn off your phone then hold volume up+power button and hold them untill you see the galaxy a70 powered by android. and then check magisk! I hope it helped!
Will try and flash complete firmware with all your Drive files tomorrow! Hope it will succeed
Captain Beretta said:
Will try and flash complete firmware with all your Drive files tomorrow! Hope it will succeed
Click to expand...
Click to collapse
I wait for your success, because I'm trying to decide to buy or not this device (root is very important to me)
infearno said:
I wait for your success, because I'm trying to decide to buy or not this device (root is very important to me)
Click to expand...
Click to collapse
I have good hope that this device can be rooted considering my past Samsung devices, it is only a matter or time.
I'm downloading the files again now, and going to try! Will report back a.s.a.p.
Edit:
Installed everyhing from your files in Odin: BL, AP (patched), CP, CSC and:
It worked! Magisk installed, Magisk Manager updated. I could install AdAway and it asked for root permissions.
But... after reboot Magisk Manager said it is NOT installed anymore. Now what?
Edit 2:
It seems Magisk sometimes fails to load when booting. After some reboots, it is back again and AdAway works. So end of the story: IT WORKS, and it Magisk starts to nag that is it not installed, just reboot a couple of times, and enjoy your rooted phone
Edit3:
Screenshots:
https://i.postimg.cc/wMrbLSpZ/Screenshot-20190515-094200-Magisk-Manager.jpg
https://i.postimg.cc/WbDyTbmv/Screenshot-20190515-094205-Magisk-Manager.jpg
https://i.postimg.cc/wjLbRfb4/Screenshot-20190515-094325-Magisk-Manager.jpg
https://i.postimg.cc/BQdV69N1/Screenshot-20190515-094336-Ad-Away.jpg
Captain Beretta said:
I have good hope that this device can be rooted considering my past Samsung devices, it is only a matter or time.
I'm downloading the files again now, and going to try! Will report back a.s.a.p.
Edit:
Installed everyhing from your files in Odin: BL, AP (patched), CP, CSC and:
It worked! Magisk installed, Magisk Manager updated. I could install AdAway and it asked for root permissions.
But... after reboot Magisk Manager said it is NOT installed anymore. Now what?
Edit 2:
It seems Magisk sometimes fails to load when booting. After some reboots, it is back again and AdAway works. So end of the story: IT WORK, and it Magisk starts to nag that is it not installed, just reboot a couple of times, and enjoy your rooted phone
Click to expand...
Click to collapse
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Avicohen21 said:
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Click to expand...
Click to collapse
That's...unfortunate. Any way to unlock samsung fully?
infearno said:
That's...unfortunate. Any way to unlock samsung fully?
Click to expand...
Click to collapse
It's not that bad, even if you accidentally booted without magisk just turn off the phone and boot with the way I mentioned and magisk is back!
If you normally power up your phone just pressing the power button with this method just add the volume up and hold both button together for 4 to 5 sec.
Right now it's the only way to root that I found. Maybe with twrp things will get easier.
And one more thing if you install magisk module don't press reboot after your install just power off and boot the way I mentioned that's it.
Avicohen21 said:
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Click to expand...
Click to collapse
I tested a few reboots, and this is how my A70 behaves:
X Reboot without pressing any buttons: no Magisk
X Reboot, pressing the power button when prompted: no Magisk
V Reboot, hold power button + volume up button, press power button to confirm: Magisk :victory:
Well, that's good enough for me! I am happy :laugh:
Captain Beretta said:
I tested a few reboots, and this is how my A70 behaves:
X Reboot without pressing any buttons: no Magisk
X Reboot, pressing the power button when prompted: no Magisk
V Reboot, hold power button + volume up button, press power button to confirm: Magisk :victory:
Well, that's good enough for me! I am happy :laugh:
Click to expand...
Click to collapse
Yeah that's right my English is not perfect maybe I didn't explained it good enough but that's what I meant! Thank you for trying. That's good enough for me also.
I also installed EdExposed and it's working good with modules that are confirmed to work with Android pie.
Next thing is trying to flash mods with flashify or something because we don't have twrp yet.
There is more good news!
I got EdXposed working following this manual, using the SandHook version: https://magiskroot.net/download-xposed-for-android-pie
It was really easy, just download and flash/install these files:
Links:
Riru core: https://github.com/RikkaApps/Riru/releases
EdXposed Sandhook: https://github.com/ElderDrivers/EdXposed/releases/tag/v0.4.1.2
EdXposed Installer: https://github.com/solohsu/XposedInstaller/releases/tag/Ed_v2.2.4
Don't forget to reboot with the button combination trick mentioned earlier!
this way can flash Treble?
5dprince said:
this way can flash Treble?
Click to expand...
Click to collapse
Not.
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
ivanox1972 said:
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
Click to expand...
Click to collapse
Here's the copy of it. View attachment 4768110
@Avicohen21 Actually I tried it on tab s5e- should be same procedure.
But I got fail result on odin flash patched ap...
Is this normal? 1 fail 0 success? or not- must be 1 success?
thanks
ivanox1972 said:
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
Click to expand...
Click to collapse
It also works with version 7.20 if you can't find an app I'll upload it.
ivanox1972 said:
@Avicohen21 Actually I tried it on tab s5e- should be same procedure.
But I got fail result on odin flash patched ap...
Is this normal? 1 fail 0 success? or not- must be 1 success?
thanks
Click to expand...
Click to collapse
If it failed maybe magisk didn't patched AP correctly try to extract the AP file again from the firmware file and then patch it in magisk again.
I extract with 7zip and got all ok in magisk. Newest 214 build.
But got success 0 fail 1 as result
Can't be ok like this?
@Avicohen21 I almost bricked it. Send me on pm your telegram contact or something to send you some pictures