My Tab S2 T713 is currently running the latest stock Samsung rom. I want to install Lineage 15.1
I've downloaded twrp-3.2.1-0-gts28vewifi.img.tar & Odin 3.12.7. I can boot into download mode, flash TWRP with Odin which says success & my tablet reboots normally. When I power down & reboot into recovery TWRP gets over written by the stock recovery.
If I uncheck Auto Reboot in Odin, after flashing success, I'm still in download mode - I've read that I need to boot directly into recovery from download mode - how do I do this?
In download mode pressing home + voldown + power reboots normally. Pressing home + volup + power does nothing
What am I doing wrong?
Gidders said:
My Tab S2 T713 is currently running the latest stock Samsung rom. I want to install Lineage 15.1
I've downloaded twrp-3.2.1-0-gts28vewifi.img.tar & Odin 3.12.7. I can boot into download mode, flash TWRP with Odin which says success & my tablet reboots normally. When I power down & reboot into recovery TWRP gets over written by the stock recovery.
If I uncheck Auto Reboot in Odin, after flashing success, I'm still in download mode - I've read that I need to boot directly into recovery from download mode - how do I do this?
In download mode pressing home + voldown + power reboots normally. Pressing home + volup + power does nothing
What am I doing wrong?
Click to expand...
Click to collapse
https://forum.xda-developers.com/tab-s2/development/twrp-3-0-2-1-galaxy-tab-s22016-sm-t713-t3390627
Instructions:
Flash with ODIN 3.10.7 in the AP slot.
Put your device in DOWNLOAD mode.
Uncheck Auto reboot.
Load the respective file below into the AP slot and hit start.
After flashing and ODIN reports PASS immediately reboot to recovery by holding POWER + HOME + VOL DOWN.
As soon as the screen goes blank change to VOL UP whilst still holding POWER + HOME.
You should now see TWRP recovery.
Brilliant - thank you. Why they can't have they have that in the Lineage install instructions?
Now running Lineage 15.1 = happy bunny
boxcar8028 said:
https://forum.xda-developers.com/tab-s2/development/twrp-3-0-2-1-galaxy-tab-s22016-sm-t713-t3390627
Instructions:
Flash with ODIN 3.10.7 in the AP slot.
Put your device in DOWNLOAD mode.
Uncheck Auto reboot.
Load the respective file below into the AP slot and hit start.
After flashing and ODIN reports PASS immediately reboot to recovery by holding POWER + HOME + VOL DOWN.
As soon as the screen goes blank change to VOL UP whilst still holding POWER + HOME.
You should now see TWRP recovery.
Click to expand...
Click to collapse
For the love of god, thank you. This wasn't in the LineageOS instructions. But I still can't install it, it says my bootloader isn't supported (T713XXU1APG1).
notmyidea said:
For the love of god, thank you. This wasn't in the LineageOS instructions. But I still can't install it, it says my bootloader isn't supported (T713XXU1APG1).
Click to expand...
Click to collapse
Did you go into your developer settings and make sure you toggled the option titled "OEM Unlock"?
sh0nuff said:
Did you go into your developer settings and make sure you toggled the option titled "OEM Unlock"?
Click to expand...
Click to collapse
Got that figured out, thanks. All installed now after much difficulty.
notmyidea said:
Got that figured out, thanks. All installed now after much difficulty.
Click to expand...
Click to collapse
Good to hear! Please make sure you give a thumbs up to anyone who helped. It really keeps the community alive and kicking!
I found that I had to do this from completely powered off state:
press home + volume up + power
wait until second "sentence" appears on screen in yellow (the first "sentence" is blue),
Then release all buttons
twrp now boots.
for some reason, my internal and external storage is showing 0 mb. Anyway to fix this?
Try formatting (not just wipe) data.
Should the Galaxy Tab S2 2016 be on TWRP 3.2.1.0 or the new 3.2.3.0 for Linage OS 15?
If so, can't you just flash the update using TWRP on the img file, or is ODIN on the tar needed?
OK, I updated to TWRP 3.2.3 using TWRP Recovery and the img file. Appears to work fine.
SvenHee said:
I found that I had to do this from completely powered off state:
press home + volume up + power
wait until second "sentence" appears on screen in yellow (the first "sentence" is blue),
Then release all buttons
twrp now boots.
Click to expand...
Click to collapse
Sorry to revisit this issue. I can't get TWRP going on my S2 Tablet. I understand these instructions, but at the end of the ODIN installation there are two possibilities that I can see. If you set the ODIN to automatically reboot then you cannot do the above because it says to do it from completely powered off.
If you don't set ODIN to reboot automatically I can't get the tablet to turn off. I can only get it to boot by holding home+volume down + power. How do I get the tablet to power off before booting??
I am using ODIN 3.14.4 and TWRP-3.7.0 9-0-gts28wifi.img.tar and my stock firmware is NRD90M.T713XXS2BSG1 with Kernel 3.10.84-14953299
Thank you.
Related
Long story short, I have the I8190L version of the phone, currently on stock ROM. I got the phone a few weeks ago and I have rooted it right away, there were no problems while rooting, I used the Galaxy S3 mini toolkit and used the "Flash Insecure Boot Image and Root device" option, with SuperSU 1.25. Fast forward to right now, I want to install CyanogenMod, so I went and tried to boot my phone into Download Mode, to try and flash CWM recovery in order to install the Cyanogen ROM, but I simply can't start download mode, when connected to the USB pressing the Vol up + menu + power sequence, the phone just starts normally (The OS will load completely). adb reboot download doesn't work too, vol up + vol down + power and plugging in the usb cable doesn't work.. I did several hard resets and I removed root too, noone of those worked. I don't know if that is relevant, but I installed a patched google play (4.1.10 Chelpus version), I could not find a way to remove that. I can't reroot too because I would need to start my phone in download mode. Anyone knows what is happening?
Gin123 said:
Long story short, I have the I8190L version of the phone, currently on stock ROM. I got the phone a few weeks ago and I have rooted it right away, there were no problems while rooting, I used the Galaxy S3 mini toolkit and used the "Flash Insecure Boot Image and Root device" option, with SuperSU 1.25. Fast forward to right now, I want to install CyanogenMod, so I went and tried to boot my phone into Download Mode, to try and flash CWM recovery in order to install the Cyanogen ROM, but I simply can't start download mode, when connected to the USB pressing the Vol up + menu + power sequence, the phone just starts normally (The OS will load completely). adb reboot download doesn't work too, vol up + vol down + power and plugging in the usb cable doesn't work.. I did several hard resets and I removed root too, noone of those worked. I don't know if that is relevant, but I installed a patched google play (4.1.10 Chelpus version), I could not find a way to remove that. I can't reroot too because I would need to start my phone in download mode. Anyone knows what is happening?
Click to expand...
Click to collapse
are you connecting your phone to PC before you go to download-mode???
try this: download-mode (Vol up + Menu + Power) and now connect your device with your computer!
flash CWM or whatever you want...
HTH
JackoMJ
That did not work, when it is about to go to download mode it seems that it fails and either boots the OS or just turns off (depends on how much I hold the buttons), and since adb reboot download doesn't work I think something got corrupted (adb finds the device and reboots it, but it just starts up normally).
I'm not sure why, but noone of the articles I read mentioned the actual CORRECT download mode sequence, which is: Volume Down + Home + Power buttons, and then click on Volume Up, it is working now. Thanks.
Gin123 said:
Long story short, I have the I8190L version of the phone, currently on stock ROM. I got the phone a few weeks ago and I have rooted it right away, there were no problems while rooting, I used the Galaxy S3 mini toolkit and used the "Flash Insecure Boot Image and Root device" option, with SuperSU 1.25. Fast forward to right now, I want to install CyanogenMod, so I went and tried to boot my phone into Download Mode, to try and flash CWM recovery in order to install the Cyanogen ROM, but I simply can't start download mode, when connected to the USB pressing the Vol up + menu + power sequence, the phone just starts normally (The OS will load completely). adb reboot download doesn't work too, vol up + vol down + power and plugging in the usb cable doesn't work.. I did several hard resets and I removed root too, noone of those worked. I don't know if that is relevant, but I installed a patched google play (4.1.10 Chelpus version), I could not find a way to remove that. I can't reroot too because I would need to start my phone in download mode. Anyone knows what is happening?
Click to expand...
Click to collapse
dwnload mod: vol down + menu + power
recovery mod: vol up + menu + power
push till it vibrates and 2-3 sec longer...
oh you solved it already sry
Gin123 said:
I'm not sure why, but noone of the articles I read mentioned the actual CORRECT download mode sequence, which is: Volume Down + Home + Power buttons, and then click on Volume Up, it is working now. Thanks.
Click to expand...
Click to collapse
Well if you looked at the screen you would know what to press after vol down+home+power
oh my God,
you are all right.
i mixed up step one and two of Download-Mode - sorry
first you have to push Vol Down + Menu + Power (few seconds)
start odin as admin
second you connect your device to PC
third you push Vol Up
fourth you flash via Odin.
I often flash ROMs via Odin and / or use CWM so that works automatically ....
JackoMJ
tried to update using sd card and oreo update after doing factory reset.
1. was on stock 2BQK2
2. downloaded BQK2 (N OS) to CQL1 (OREO).zip added to sd
3. did fsactory reset from recover
4. then went up to update from recovery. ran the file above.
5. when i rebooted i get stuck on boot screen
steps taken.
1. hold down bixby and up volume then power ....does nothing
2. hold down just power does nothing
3. hold down bixby vlume up and power does nothing
4. hreboots back yo boot screen then stops on boot screen
5. hold down volume then power 7 seconds until screen turns black and just before she reboots i let go of volune down and power then immidiately hold down volume again without power button, this seems to torn off phone.
so as you see i cant get into download, recovery or safe mode. just start to boot screen or off
please i know i want to odin stock filmware back but cant seem to get phone into download mode.
i,m tired and most likly nissed an important step help please.
I do no see where you tried download mode... Hold volume down bixby and power for about 2min. That will get you to download
Ok I can get it in download mode
I get Odin to recognize.
Fill up the slots
BL
AP
CL
CSC?
USM
Using latest Verizon .
I eitther get stuck on setup initialize or
Update fail.
pospower said:
Ok I can get it in download mode
I get Odin to recognize.
Fill up the slots
BL
AP
CL
CSC?
USM
Using latest Verizon .
I eitther get stuck on setup initialize or
Update fail.
Click to expand...
Click to collapse
if you get stuck at setup connection or initialize try a different usbport/cable/computer
I am trying to install LineageOS on a brand new SM-T713. I have booted the device into Odin mode and used Heimdall to flash TWRP. AFAICT, this completed successfully.
Now I am supposed to power the device off and reboot it into recovery mode, but I can't figure out how to power it off.
Any ideas?
UPDATE: The solution was to hold down the volume-up, volume-down, and power buttons simultaneously; this reboots the device. Fortunately, the stock OS did not overwrite the recovery partition, so I was able to power-off and boot into TWRP.
ipilcher said:
I am trying to install LineageOS on a brand new SM-T713. I have booted the device into Odin mode and used Heimdall to flash TWRP. AFAICT, this completed successfully.
Now I am supposed to power the device off and reboot it into recovery mode, but I can't figure out how to power it off.
Any ideas?
UPDATE: The solution was to hold down the volume-up, volume-down, and power buttons simultaneously; this reboots the device. Fortunately, the stock OS did not overwrite the recovery partition, so I was able to power-off and boot into TWRP.
Click to expand...
Click to collapse
Just POWER + VOL DOWN to reboot.
Unfortunately I flashed a bad Rom to my note superiorOS rom.
As a result the put is stuck on superiorOS boot logo
I cannot with any of the usual key combos get into recovery mode or display the download mode screen.
I have tried to refresh with odin but although with the superiorOS boot logo it shows as connect to odin it will not get past setupconnection.
Any help would be really great.
Thank you in advance
TD100_1 said:
Unfortunately I flashed a bad Rom to my note superiorOS rom.
As a result the put is stuck on superiorOS boot logo
I cannot with any of the usual key combos get into recovery mode or display the download mode screen.
I have tried to refresh with odin but although with the superiorOS boot logo it shows as connect to odin it will not get past setupconnection.
Any help would be really great.
Thank you in advance
Click to expand...
Click to collapse
If you're using Note9 you can try the following:
- Connect the usb cable to your pc
- Make sure you have the drivers installed (one way to do this is installing Samsung Dex for Windows)
- Press and Hold the Volume Down + Bixby button + Power Button
- After around 7 seconds, the phone should enter Download Mode and you can flash again with Odin or others
Another thing you can do if you have TWRP is first enter on Download mode, choose Restart and immediately after press and hold Volume Up Button + Power Button and it should enter Recovery Mode and boot TWRP
VHFG22 said:
If you're using Note9 you can try the following:
- Connect the usb cable to your pc
- Make sure you have the drivers installed (one way to do this is installing Samsung Dex for Windows)
- Press and Hold the Volume Down + Bixby button + Power Button
- After around 7 seconds, the phone should enter Download Mode and you can flash again with Odin or others
Another thing you can do if you have TWRP is first enter on Download mode, choose Restart and immediately after press and hold Volume Up Button + Power Button and it should enter Recovery Mode and boot TWRP
Click to expand...
Click to collapse
Thank you for your suggestion. Unfortunately I have tried all of those options and none work. My note 9 connects to the PC when I connect it, and shows as connected in Odin however the screen os stuck on the new roms boot logo. When I try and flash firmware through Odin even if I am using the .pit file odin get stuck at setupconnection.
Trying to root my galaxy M31 by flashing a TWRP recovery file but I got this above error!...
Finally end up with... Neither I can restart phone (volume down + power) coming to same screen nor enter to TWRP recovery mode (volume up + power) also coming to same screen!!!
Worst case is here I cannot connect to Odin tool to solve this thing!...
I referred this blog for rooting: Install TWRP Recovery on Samsung Galaxy M31 (magiskzip.com)
My feeling: brought this phone yesterday and now got messed up.
Please help me with this thing, I'm done of it!
Thank you...
psychotic.predator said:
Trying to root my galaxy M31 by flashing a TWRP recovery file but I got this above error!...
Finally end up with... Neither I can restart phone (volume down + power) coming to same screen nor enter to TWRP recovery mode (volume up + power) also coming to same screen!!!
Worst case is here I cannot connect to Odin tool to solve this thing!...
I referred this blog for rooting: Install TWRP Recovery on Samsung Galaxy M31 (magiskzip.com)
My feeling: brought this phone yesterday and now got messed up.
Please help me with this thing, I'm done of it!
Thank you...
Click to expand...
Click to collapse
try flashing this vbmeta...
psychotic.predator said:
Trying to root my galaxy M31 by flashing a TWRP recovery file but I got this above error!...
Finally end up with... Neither I can restart phone (volume down + power) coming to same screen nor enter to TWRP recovery mode (volume up + power) also coming to same screen!!!
Worst case is here I cannot connect to Odin tool to solve this thing!...
I referred this blog for rooting: Install TWRP Recovery on Samsung Galaxy M31 (magiskzip.com)
My feeling: brought this phone yesterday and now got messed up.
Please help me with this thing, I'm done of it!
Thank you...
Click to expand...
Click to collapse
Today, January 25, the article has been updated. Sorry for the previous error. Please follow the guide in the article now. Additionally, if you have any issues or problems while following the guide, you can live chat with the magiskzip.com team. They will reply within 5 minutes.
BishalPo said:
Today, January 25, the article has been updated. Sorry for the previous error. Please follow the guide in the article now. Additionally, if you have any issues or problems while following the guide, you can live chat with the magiskzip.com team. They will reply within 5 minutes.
Click to expand...
Click to collapse
killerboychetan said:
try flashing this vbmeta...
Click to expand...
Click to collapse
this vbmeta i tried but it doesn't work in android 12
meryem demirbaş said:
this vbmeta i tried but it doesn't work in android 12
Click to expand...
Click to collapse
Ohh! Okay...
m13 androd 12 U3 twrp and vbmeta updated
link : https://forum.xda-developers.com/t/...p-for-galaxy-m31.4260181/page-3#post-88630365
Extract the zip file I added to the folder and open the Frija software. Download your firmware by entering the version and model of your device and the code of the country where the device is registered. Copy the AP file and paste it on your device. Open magisk manager app and tap install. Patch the AP file. When the process is finished, you can transfer the tar file named magik pacthed in the download folder to the AP section via odin, the file starting with the BL you downloaded with the Frija software, to the BL section, etc. Select HOME CSC in the USERDATA section, if you do not want your information to be deleted. Turn off your device, press the volume down, volume up and power button at the same time, and when the screen turns black, remove your finger from the power button and put it into download mode. Before starting the installation from the Odin software, deselect the Automatic Restart option in the Odin software options section and try to Start. When you get the AVB (fail) error, press the volume down, volume up and power button at the same time, and when the screen turns black, remove your finger from the power button and enter the download again. Deselect the AP partition, click Start again and wait. After installing the device, disconnect the cable and install Magisk Manager, if it does not stop. reboot if prompted. and now your device is rooted.