Hi Guys,
I really need help with this one. I have tried almost everything.
Here is my problem.
I have an Rog phone 3 strix edition QUALCOMM based.
I repaired the screen because i dropped the phone.
Everything was fine working well. Me with my big head decided to do an factory reset to wipe everything clean from the phone and then the problem started.
The phone was restarting every time i plugged in a usb c cable. If i wanted to listen to some music on headset wont work because it will end in a bootloop.
Now the phone is stuck in CSC Fastboot mode and PC wont recognized it. The screen will turn on and send me to CSC fastboot but that's it. I can turn it back off.
Can i Revive the phone or is it food for the recycling bin?
Please Help.
Sincerely,
Ayolyas
With some effort you should be able to get back on track - unless it's hardware related to the display change you've done.
Can you do a reboot to bootloader from the boot menu? If you can confirm if you have fastboot access. If you do, RAW flash the device.
Worst case, you force the device into EDL mode and do a flash from there, but leave at as the last option.
If the relpaced display is causing harware issues, that's a bigger problem...
Hi Andrologic,
I cannot reboot to the bootloader. I am stuck in csc fastboot. I was trying to put it in edl mode i even bought an edl cable. But i have no idea how to use it or how to put the phone in edl.
I went back to the repair shop but the phone was working fine when it left the phone shop. The problem started when i decided to go for factory reset.
ayolyas said:
Hi Andrologic,
I cannot reboot to the bootloader. I am stuck in csc fastboot. I was trying to put it in edl mode i even bought an edl cable. But i have no idea how to use it or how to put the phone in edl.
I went back to the repair shop but the phone was working fine when it left the phone shop. The problem started when i decided to go for factory reset.
Click to expand...
Click to collapse
So, when you turn on the device, it falls into CSC FB and you can't navigate anywhere at all from there?
What happens if you try to do a RAW flash from CSC FB?
Flashing it in EDL mode may otherwise be the only option. Power off the device completely. Then hold Vol up+down pressed and connect to the USB side port. You should land with a completely black screen and on your pc see the device identified in 9008 mode - that's EDL. Since you have a flash cable, you can obviously use that too.
Remember you need Qualcom drivers installed to work in EDL mode. There is a guide with steps for EDL flashing somewhere here on the forum. All the steps are explained.
Andrologic said:
So, when you turn on the device, it falls into CSC FB and you can't navigate anywhere at all from there?
What happens if you try to do a RAW flash from CSC FB?
Flashing it in EDL mode may otherwise be the only option. Power off the device completely. Then hold Vol up+down pressed and connect to the USB side port. You should land with a completely black screen and on your pc see the device identified in 9008 mode - that's EDL. Since you have a flash cable, you can obviously use that too.
Remember you need Qualcom drivers installed to work in EDL mode. There is a guide with steps for EDL flashing somewhere here on the forum. All the steps are explained.
Click to expand...
Click to collapse
I cannot navigate anywhere from csc. If i try to reboot bootloader i will end in the same place.
I try to connect like you told me Vol up + down but i ended up at the same place. An raw flash from csc fb how do i do that?
And the steps for edl if you can help where to find those steps because my google history is full off items and still no luck finding the right one.
ayolyas said:
I cannot navigate anywhere from csc. If i try to reboot bootloader i will end in the same place.
I try to connect like you told me Vol up + down but i ended up at the same place. An raw flash from csc fb how do i do that?
And the steps for edl if you can help where to find those steps because my google history is full off items and still no luck finding the right one.
Click to expand...
Click to collapse
Yes, you have flash cable, so getting into EDL shouldn't be an issue any way.
This is a useful video on how to use your flash cable to force the device to EDL:
Just remember you need QCom drivers installed to flash in EDL mode, the normal drivers won't do it in EDL.
What is the device identified as on your PC when in CSC FB? Can you send any FB commands to the device at all? Does 'Fastboot Devices' return your device id? If so, try first to do a RAW flash from the Fastboot state you are stuck at. You don't really want to mess with EDL if you can avoid it. Download one of the RAW rom's from the links here on the forum. Version number doesn't matter as long as it matches with your device version, i.e. WW assuming you're on Global.
ayolyas said:
Hi Guys,
I really need help with this one. I have tried almost everything.
Here is my problem.
I have an Rog phone 3 strix edition QUALCOMM based.
I repaired the screen because i dropped the phone.
Everything was fine working well. Me with my big head decided to do an factory reset to wipe everything clean from the phone and then the problem started.
The phone was restarting every time i plugged in a usb c cable. If i wanted to listen to some music on headset wont work because it will end in a bootloop.
Now the phone is stuck in CSC Fastboot mode and PC wont recognized it. The screen will turn on and send me to CSC fastboot but that's it. I can turn it back off.
Can i Revive the phone or is it food for the recycling bin?
Please Help.
Sincerely,
Ayolyas
Click to expand...
Click to collapse
Have you fix it?
osomakohj said:
Have you fix it?
Click to expand...
Click to collapse
Hi,
Nope. I can get into EDL mode so i think it is hardware related. You can say it is fresh for the garbage.
ayolyas said:
Hi,
Nope. I can get into EDL mode so i think it is hardware related. You can say it is fresh for the garbage.
Click to expand...
Click to collapse
maybe try edl cable maybe it'll work? its very cheap in online store
osomakohj said:
maybe try edl cable maybe it'll work? its very cheap in online store
Click to expand...
Click to collapse
I did use a EDL cable and i also build one but no succes for both.
ayolyas said:
I did use a EDL cable and i also build one but no succes for both.
Click to expand...
Click to collapse
Hope you did the proper way of entering edl mode. btw you can still send that to service center. but first try some other way as your phone still boot
Related
My Xiaomi mi5 does not turn on.
No lights, fastboot is not accessible, resetting it does not do anything.
Basically for any combination of buttons that I press, nothing happens and the screen stays black - it is completely dead.
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fastboot in order to flash the ROM, but is there a way to get to fastboot using my pc? Or even turn the phone on with commands? At the moment ADB and Fastboot does not recognise my phone, is there a way to make it detect it from the state it is in?
Thanks
sivd said:
My Xiaomi mi5 does not turn on.
No lights, fastboot is not accessible, resetting it does not do anything.
Basically for any combination of buttons that I press, nothing happens and the screen stays black - it is completely dead.
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fastboot in order to flash the ROM, but is there a way to get to fastboot using my pc? Or even turn the phone on with commands? At the moment ADB and Fastboot does not recognise my phone, is there a way to make it detect it from the state it is in?
Thanks
Click to expand...
Click to collapse
Do you have all the necessary driver installed? I think yes and that is why you are seeing in (COM3) port. You can do one thing, Unplug the phone from PC and Press and Hold Vol Down (-) and plug in again. If not works then you can also Press and HOLD Vol Down and Press and HOLD Power button until you see Fast boot menu. If don't work then try the same thing with Vol UP button. Then you suppose to see a MI phone logo with a USB cable.
"qualcomm hs-usb qdloader 9008" Is a signal of Hard Brick for QCOM devices (Like for LG G2);
http://forum.xda-developers.com/lg-g2/general/fix-unbrick-lg-g2-stuck-qualcomm-hs-usb-t2933830
As you can see here, for fix it you need all partition files, all system files, and a programm
But i dont know if it will works also on SD820, you might need all files for Mi5
Just a question: How did you bricked your phone?
EDIT:
I had an idea: maybe inside fastboot rom you can find all files you need, it might be worth a try, at least you can send it to your shop where you bought it
sivd said:
However, when I plug it into my pc, the devices shows up as qualcomm hs-usb qdloader 9008 (COM3) which is the only sign of life from the phone.
What I want to know is if it is possible for me to unbrick the phone from this situation. I understand that I need to get into fas,tboot in order to flash the ROM
Click to expand...
Click to collapse
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
I also had the same issue with black screen and no responses from vol. & power buttons. But when I notice that in device manger it showed the qcom driver, then I new that there was hope to recover the phone. I can confirm that this will unbrick your phone. I MiFlash'd the China Rom (non-dev), unlocked the bootloader, MiFlash'd MiFlash_xiaomi.eu_gemini_V7.2.13.0.MAACNDB_6.0 rom, sideload lastest stable EU rom, TRWP and SuperSU.
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here:
3: download the latest dev rom from here:
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
Thank you so much, this has worked perfectly and saved me a lot of money! I really appreciate your help, thank you again!
sivd said:
Thank you so much, this has worked perfectly and saved me a lot of money! I really appreciate your help, thank you again!
Click to expand...
Click to collapse
Glad you could salvage your device.
Now remember - from great flashing power comes great responsibility ;]
adwinp said:
1: if you're detecting it as qcom 9008, there's a good chance it's in EDL mode, which is good news
2: download MiFlash from here: https://www.androidfilehost.com/?fid=24521665358595574
3: download the latest dev rom from here: http://update.miui.com/updates/v1/fullromdownload.php?d=gemini&b=X&r=cn&n=
4: Extract the files to C:\
5: Open MiFlash & point the folder to the root ROM folder, example: C:\gemini_foo_bar, NOT C:\gemini_foo_bar\images
6: connect your phone & select flash all (1st option from the left, bottom of MiFlash tool)
This might take a few tries (example - you might receive "missed hello packets)
Once you're done, you can stay with the China Dev, unlock the bootloader & flash a xiaomi.eu rom, or CM.
Good luck.
Click to expand...
Click to collapse
Thanks for the guide, 1 q tho: what to do when i get the "missed hello packets, try to recover" message?, wait or restart the process?
Ok, solved by disabling driver sign (press F8 during boot)
Hello , i got the same problem as described at this topic and here is my problems :
I can't turn on my phone and i can't put it in fastboot mode ( tryed a lot of buttons combinations)
But when i plug it into my pc - it recognizes as Android
I have tryed to install drivers but windows shows mistake and can't install that
When my device connected to pc and i press volume + and power buttons - in few minutes system(WIN 10) recognizes it as ADB interface(can't install drivers too) and i have acess to mi5 internal storage ( i can download photos and so on )
But mi flash doesn't see phone in any mode and i feel that my device is still alive and i can recover it but don't know how....
I will be grateful for any help !
Isteran said:
Hello , i got the same problem as described at this topic and here is my problems :
I can't turn on my phone and i can't put it in fastboot mode ( tryed a lot of buttons combinations)
But when i plug it into my pc - it recognizes as Android
I have tryed to install drivers but windows shows mistake and can't install that
When my device connected to pc and i press volume + and power buttons - in few minutes system(WIN 10) recognizes it as ADB interface(can't install drivers too) and i have acess to mi5 internal storage ( i can download photos and so on )
But mi flash doesn't see phone in any mode and i feel that my device is still alive and i can recover it but don't know how....
I will be grateful for any help !
Click to expand...
Click to collapse
If you can see it in adb, you might be able to see it in fastboot.
Try go in to fastboot (even though you can't see it on screen.)
And try fastboot oem device-info see if you can get anything. Then we go from there.
DrBubblewrap said:
If you can see it in adb, you might be able to see it in fastboot.
Try go in to fastboot (even though you can't see it on screen.)
And try fastboot oem device-info see if you can get anything. Then we go from there.
Click to expand...
Click to collapse
tryed a lot of time to go to fastboot , but nothing happened...
same issue
I've been having the same problem with my MI5, 128gb running MIUI8 6.6.23CN, unlocked bootloader
It started when I did an OTA from 6.6.16, then OTA failed, I tried again this time it downloaded full rom and went into my twrp but installation started automatically. Then it rebooted but the system stayed in black screen. I forced-rebooted it, then everything was fine and I was on 6.6.23. I was using the phone normally for a few hours, then around 6hr later after I upgraded, I took phone out of my bag and it was bricked. I tried everything, no fastboot, no adb, no recovery, no led, nothing on screen. MiFlash reconizes (cuz of the 9008 status) but flash fails. I event opened it up, disconnected the 3 cables from the battery and hold onto power buttons for few seconds to try to drain whatever power it has left in system. Reconnected battery but no change.
I gave up, put phone back in case and was going to ask friend to take it back to send to china for repair the next day, but then I too it out an hour before I go meet my friend and suddenly, phone led flashed red and I see on screen out-of-battery icon. I plugged it in to charge then LED flickered quickly in red for a bit then turn solid red, then turned orange. I let it charged for 10min or so, and pressed power+Vol_Down for few seconds. Lo and behold, I got the bunny on screen and went into fastboot. I was able to re-flash 6.6.23 and phone was good to go again. (but why did removing battery cables do the same thing? Maybe I didn’t leave it disconnected long enough?)
Good story until this part… then 2 days later, I wanted to test MI Talk with friend, I click on it, and phone froze. Both touch sensor light stayed on. I waited about 15 second and forced reboot. Phone vibrates once and then went into hard brick again. Exactly same situation, nothing works.
Now I am waitng for phone to discharge by itself. God knows how many days it will take. It was 96% charged. (1st time I had about 45% and too a day to discharge)
Only if I can get back into fastboot......
tkrave said:
I've been having the same problem with my MI5, 128gb running MIUI8 6.6.23CN, unlocked bootloader
It started when I did an OTA from 6.6.16, then OTA failed, I tried again this time it downloaded full rom and went into my twrp but installation started automatically. Then it rebooted but the system stayed in black screen. I forced-rebooted it, then everything was fine and I was on 6.6.23. I was using the phone normally for a few hours, then around 6hr later after I upgraded, I took phone out of my bag and it was bricked. I tried everything, no fastboot, no adb, no recovery, no led, nothing on screen. MiFlash reconizes (cuz of the 9008 status) but flash fails. I event opened it up, disconnected the 3 cables from the battery and hold onto power buttons for few seconds to try to drain whatever power it has left in system. Reconnected battery but no change.
I gave up, put phone back in case and was going to ask friend to take it back to send to china for repair the next day, but then I too it out an hour before I go meet my friend and suddenly, phone led flashed red and I see on screen out-of-battery icon. I plugged it in to charge then LED flickered quickly in red for a bit then turn solid red, then turned orange. I let it charged for 10min or so, and pressed power+Vol_Down for few seconds. Lo and behold, I got the bunny on screen and went into fastboot. I was able to re-flash 6.6.23 and phone was good to go again. (but why did removing battery cables do the same thing? Maybe I didn’t leave it disconnected long enough?)
Good story until this part… then 2 days later, I wanted to test MI Talk with friend, I click on it, and phone froze. Both touch sensor light stayed on. I waited about 15 second and forced reboot. Phone vibrates once and then went into hard brick again. Exactly same situation, nothing works.
Now I am waitng for phone to discharge by itself. God knows how many days it will take. It was 96% charged. (1st time I had about 45% and too a day to discharge)
Only if I can get back into fastboot......
Click to expand...
Click to collapse
You don't have to go into fastboot to use miflash if you have stock recovery
Sent from my MI 5 using Tapatalk
vf1 said:
You don't have to go into fastboot to use miflash if you have stock recovery
Sent from my MI 5 using Tapatalk
Click to expand...
Click to collapse
how do you flash stock recovery if you dont need to go into fastboot? now I am unable to go into recovery or fastboot as the phone does not boot at all. connecting it to PC reconizes the phone as the infamous "Qualcomm HS-USB QDLoader 9008" device.
Its been 4 days and the damn battery hasnt run out yet as I can still plug into pc and get qualcom 9008 to come up. I think I am going to send to china to get it fixed properly if I still cannot get the red flicker of low battery power to come up by tomorrow.
It has happened to me 3-4 times already. It didnt want to boot. No signs of life either. I even sent a message to the shop for sending it back..the only thing that was telling me it wasn't completely dead, was the qualcomm driver ,while on USB connection with the PC, which you are referring to as well
Here is what you could try doing. Try pressing the power button for about 30 seconds at first. If it does not boot, try bending the phone real gently back and forth (don't break it!!). Preferably, hit it gently with your palm while holding it in your other hand.( -- I know it might sound weird --) I noticed that it's shutting down while i have it in my pocket and doing some work which squeezes the phone a bit against my leg.
I came to the conclusion that some connection must become loose when some pressure is being applied to it.. Unfortunately it has to be a design flaw of the phone. Nothing random with yours or mine , in my opinion. // I have a case and tempered glass installed as well since the first minute I got it in my hands..
Sent from my MI 5 using XDA-Developers mobile app
Thanks for the tips Takkaros. I tried what you said but nothing changed (though I was a bit scared to bend it too hard). 1st time it happened to me, I had around 40-50% battery and somehow battery completely drained 24hr later so I got the red blinking low of battery light and was able to charge the phone up and go back into fastboot, which solved everything. this time it happened when I had 96% battery(which I knew cuz I was using the phone, then clicked MI Talk and phone froze, then bricked). I wish there is a way for me to force a battery drain without opening it up. I did opened it up once(on the 1st brick) and disconnected the 3 battery cables, but it was still in brick state when I put everything back.
The qualcomm 9008 driver detection was also my concern about sending back the phone. Chances are by the time my phone reaches the repair shop, battery is completely dead and they simply charge the battery then flash a stable rom and send it back to me without changing out the motherboard or whatever. Which in such case it will be faster for me to just wait a week or two and do myself, instead of shipping it to china and wasting shipping cost and probably will take 4-6 weeks.
I am not sure whats wrong with this phone. Sometimes it turns off while i have in on charge at night, with the Green led lighting. I can get into recovery mode but all the partitions are missing. I cant wipe anything and all my files are not there. If I restart the recovery 2-3 times everything comes back to normal. Maybe there is something wrong with the flash drive. If honorbuy replied to my messages i'd sent it back to them asap. This is not a reliable phone for daily use
Sent from my MI 5 using XDA-Developers mobile app
Try using mi flash. Follow the instruction
Sent from my MI 5 using Tapatalk
I am sending back the phone to china to have them "fix" it. Not sure what they will do, hopefully they either swap me a new phone or swap out the motherboard or something. I just hope they dont just boot into fastboot (after battery completely drained and system resets) and flash new rom and send it back to me.
Probably will take a month or so. Good thing i still have my old phone.
tkrave said:
I am sending back the phone to china to have them "fix" it. Not sure what they will do, hopefully they either swap me a new phone or swap out the motherboard or something. I just hope they dont just boot into fastboot (after battery completely drained and system resets) and flash new rom and send it back to me.
Probably will take a month or so. Good thing i still have my old phone.
Click to expand...
Click to collapse
This happened to me recently. I used mi flash and the global 7.2.4 stable fastboot rom to get it going again. Wouldn't work for me with with with newer versions. Think edl has been disabled on them.
Bootloader type = Oxygen (not sure if that is the proper one for the device though)
Bootloader lock = Unlocked via Xiaomi official procedure
USB Debug = Not sure, I'm starting to fear it's off though
Original issue = My phone was bricked. No sound, display or whatsoever.
What did I try?
I followed an unbrick tutorial which made me flash an Oxygen firmware file. After that I get a boot loop. Mi logo and Android loading bar appears and seems to be like that continuously.
I can't access either fastboot or recovery mode. If I try any of the two button combinations I don't even get the Mi logo screen. I see the backlight turn on and nothing happens.
I tried flashing several fastboot roms, stock roms and firmware files I could find, flashing them with different versions of MiFlash. Except for the one I described in step 1 none of them change the situation as described in 'Original issue'.
I need to use the 'test pin method' to even let the computer detect the phone in MiFlash. The phone does not get detected inADB fasboot (which makes sense, as I can't enter fastboot mode anyway).
I'm hoping someone can point me in a direction which leads me to fix my phone. I'm not sure what steps I did to even get to the point where it stopped responding in any way. It has been some time ago, but I think I flashed an Oreo firmware file just before that point.
i did tryied test point (edl mode) and i think either i connect wrong point together or my rom was wrong and my phone can not boot or show anything . when connect to charge it shows key light flashing without any picture in the screen and without any vibration after pushing power button . i either dont have acces to fastboot now . what is wrong with my phone ?
Esemtix said:
i did tryied test point (edl mode) and i think either i connect wrong point together or my rom was wrong and my phone can not boot or show anything . when connect to charge it shows key light flashing without any picture in the screen and without any vibration after pushing power button . i either dont have acces to fastboot now . what is wrong with my phone ?
Click to expand...
Click to collapse
If you find the right points you can get into edl. Did you try a cable already?
Arealhooman said:
If you find the right points you can get into edl. Did you try a cable already?
Click to expand...
Click to collapse
i dont know i connect right point together or not but my phone name changed when connect to pc with xiaomi fastboot installer and i gave my phone to a developer and he install a lot of roms with edl mode ,too but there is no change
Try using edl cable
Arealhooman said:
Try using edl cable
Click to expand...
Click to collapse
i dont need any box tool for use it ?
What do you mean?
Arealhooman said:
What do you mean?
Click to expand...
Click to collapse
boxes like flash you can connect to pc and acces more thing for connecting to your phone
i mean i wont need anything like these except edl cable ?
sorry i ask too many questions
Esemtix said:
boxes like flash you can connect to pc and acces more thing for connecting to your phone
i mean i wont need anything like these except edl cable ?
sorry i ask too many questions
Click to expand...
Click to collapse
Nah it’s k. You still need the right files, but most of the time a edl cable can get you in.
i did tryied edl mode and just black screen does shows. what should i do ? my phone either doesn not vibrate when connect to charge
janus.8x said:
i did tryied edl mode and just black screen does shows. what should i do ? my phone either doesn not vibrate when connect to charge
Click to expand...
Click to collapse
Someone told me the phone got hard problem .
janus.8x said:
i did tryied edl mode and just black screen does shows. what should i do ? my phone either doesn not vibrate when connect to charge
Click to expand...
Click to collapse
hi . I tried to flash the phone a lot but still the phone keys light are just on when I connect the phone to charger and when I disconnected it , it is off even when I push power key
what should I do ?
Hi everyone,
I was wondering does anyone know the Nokia TA-1004 JTAG points by any chance?
I tried looking around and I can't seem to find anything.
Because of my bricked device, I am thinking of going down the JTAG route to extract my data.
This is the absolute last resort as I REALLY don't want to loose any of my data, primarily Contacts and Messages
Hope to hear back from you wonderful lot ?
Nokia_8_fan said:
Hi everyone,
I was wondering does anyone know the Nokia TA-1004 JTAG points by any chance?
I tried looking around and I can't seem to find anything.
Because of my bricked device, I am thinking of going down the JTAG route to extract my data.
This is the absolute last resort as I REALLY don't want to loose any of my data, primarily Contacts and Messages
Hope to hear back from you wonderful lot
Click to expand...
Click to collapse
I don't know what JTAG is. Please give some more info about your bricked device, how you bricked it etc. It might be possible to recover it without hardware intervention. Looking at your current post I am guessing you have a hard brick. In that case you have 2 options:
1.) Press and hold power button for about 2-4 minutes and wait for the device to shut down. When the device shuts down, boot to fastboot mode and fix any broken partitions.
2.) If that doesn't work you need hardware based methods. You need to open your device and short some pins to enter Qualcomm EDL (Emergency Download) mode. From there you can recover your device.
emufan4568 said:
I don't know what JTAG is. Please give some more info about your bricked device, how you bricked it etc. It might be possible to recover it without hardware intervention. Looking at your current post I am guessing you have a hard brick. In that case you have 2 options:
1.) Press and hold power button for about 2-4 minutes and wait for the device to shut down. When the device shuts down, boot to fastboot mode and fix any broken partitions.
2.) If that doesn't work you need hardware based methods. You need to open your device and short some pins to enter Qualcomm EDL (Emergency Download) mode. From there you can recover your device.
Click to expand...
Click to collapse
Thanks for getting back to me.
I have done both suggestions and they don't work.
It is probably a hard bricked device, the only thing I can get is a 9008 recognition in Device Manager.
QFIL, OST and NOST doesn't seem or want to communicate with the device either
Did you open your device and short the pins required? EDL mode is different than Download mode. OST and NOST work in Download Mode not EDL. QFIL does support EDL mode. If you look at this article (https://xiaomitools.com/how-to-use-qualcomm-flash-image-loader-tool-qfil/) at Step 5 it mentions that the device should be recognised as 9008 which you mention it does. Have you installed the Qualcomm drivers? Please provide some screenshots too, it is difficult to help you without specific info about your problem
emufan4568 said:
Did you open your device and short the pins required? EDL mode is different than Download mode. OST and NOST work in Download Mode not EDL. QFIL does support EDL mode. If you look at this article (https://xiaomitools.com/how-to-use-qualcomm-flash-image-loader-tool-qfil/) at Step 5 it mentions that the device should be recognised as 9008 which you mention it does. Have you installed the Qualcomm drivers? Please provide some screenshots too, it is difficult to help you without specific info about your problem
Click to expand...
Click to collapse
@emufan4568
Sorry for my late reply, but I thought Download Mode is the same as EDL mode???
And yes, I have the Qualcomm drivers installed.
I have also shorted the EDL pins on the board, this did not do anything at all.
I have tried QFIL many times and it keeps giving me error messages.
I have done so many things and posted screenshots across the forums that I am at a complete lost!
Nokia_8_fan said:
@emufan4568
Sorry for my late reply, but I thought Download Mode is the same as EDL mode???
And yes, I have the Qualcomm drivers installed.
I have also shorted the EDL pins on the board, this did not do anything at all.
I have tried QFIL many times and it keeps giving me error messages.
I have done so many things and posted screenshots across the forums that I am at a complete lost!
Click to expand...
Click to collapse
EDL mode is Emergency Download Mode in Qualcomm devices for recovering the device at a low level. QFIL calls it download mode but it really is not. Download mode in Nokia phones is really fastboot mode or bootloader mode where you basically communicate with the bootloader and flash/erase images from the device. From what I have seen though NOST supports EDL mode too (with the Emergency Download option) but it does not really work well.
I installed android 12 beta on my Mi 11 ultra. Did not like it and wanted to install global. Installed TWRP, wiped data and instead of rebooting in twrp, I tried to enter fastboot mode via adb. The phone screen turned black. Now it is not showing in ADB, not detected by Mi flash tool, not enetering fastboot mode and not entering recovery. When I connect it to computer, there is this connecting sound but soon it is followed by disconnecting sound. Not even getting the charging screen. In the device manager on Windows, there is this Qualcum HS-USB QDLoader 9008 (COM9) when the phone is connected via USB cable to PC.
Anyway to restore any firmware on it? It is a CN version, star, has bootloadder unlocked.
EDL time? Or even worse? Is it paperweight now?
EDL time I think.
Sathelp said:
EDL time I think.
Click to expand...
Click to collapse
Believe me, this is reassuring. I'm happy to settle on EDL instead of paperweight... For EDL does the phone need to be opened, back cover removed and then that magic short circuit or is there a way to get it done without opening the phone?
hellodrsoul said:
Believe me, this is reassuring. I'm happy to settle on EDL instead of paperweight... For EDL does the phone need to be opened, back cover removed and then that magic short circuit or is there a way to get it done without opening the phone?
Click to expand...
Click to collapse
Don't worry. When mine was EDL flashed the guy asked me to download a specific miflash version that he had the link for and the ROM of choice to be flashed. I connected the phone to the PC, he connected, asked me to put it in to EDL mode ( he will explain if your not sure) and done his stuff using TeamViewer with control of my desktop. Once finished, just rebooted when asked, all done.
need mi auth to flash
How do you put the phone in EDL mode?
can you get your phone on fastboot?
xNAPx said:
How do you put the phone in EDL mode?
Click to expand...
Click to collapse
Hold both vol up and down while powering up or adb, adb reboot edl or fastboot, fastboot oem edl . You will see edl drivers load on your PC.
Thank you guys for your replies. I got it fixed and now it is rocking again. If anybody faces the same issue, please see details below.
Diagnosis: EDL mode
Signs and problems: Completely dead phone. Black screen. None of the buttons or their combinations work. Volume down plus power, volume up plus power, Both volume buttons, All three buttons. None of these worked in this EDL mode. In fact, the only sign that this phone was "alive" was the Qualcomm driver showing in the device manager when the phone was connected to a PC. There was this yellow sign even on the Qualcomm driver and the official Xiaomi flash tool failed to detect the phone due to the Qualcomm driver malfunction. Got the Qualcomm driver working (the yellow sign on the driver name icon in device manager) by disabling windows driver signature check. After this the phone was detected by the official Xiaomi flash tool. When I tried to flash the official and stock CN ROM, it did not allow me and gave the error "you are not authorized to download". Took the phone to Xiaomi service, they refused as the phone was of another region. They did not know any unofficial paid solution. Took it to local technicians. They tried but failed (ultimate multi-tool, some other tool they called as "aqua" did not work.
Treatment: Searched online and found a YouTube channel (
). Paid USD 35 and got it flashed via TeamViewer. I just sat anxiously (praying that he must not be a scammer...). He did some magic and successfully flashed the phone with the original CN ROM with the boot loader unlocked. I then was able to install the global version via fastboot as usual.
Thanks again for the free support I got here. Obliged and stay blessed
hellodrsoul said:
Thank you guys for your replies. I got it fixed and now it is rocking again. If anybody faces the same issue, please see details below.
Diagnosis: EDL mode
Signs and problems: Completely dead phone. Black screen. None of the buttons or their combinations work. Volume down plus power, volume up plus power, Both volume buttons, All three buttons. None of these worked in this EDL mode. In fact, the only sign that this phone was "alive" was the Qualcomm driver showing in the device manager when the phone was connected to a PC. There was this yellow sign even on the Qualcomm driver and the official Xiaomi flash tool failed to detect the phone due to the Qualcomm driver malfunction. Got the Qualcomm driver working (the yellow sign on the driver name icon in device manager) by disabling windows driver signature check. After this the phone was detected by the official Xiaomi flash tool. When I tried to flash the official and stock CN ROM, it did not allow me and gave the error "you are not authorized to download". Took the phone to Xiaomi service, they refused as the phone was of another region. They did not know any unofficial paid solution. Took it to local technicians. They tried but failed (ultimate multi-tool, some other tool they called as "aqua" did not work.
Treatment: Searched online and found a YouTube channel (
). Paid USD 35 and got it flashed via TeamViewer. I just sat anxiously (praying that he must not be a scammer...). He did some magic and successfully flashed the phone with the original CN ROM with the boot loader unlocked. I then was able to install the global version via fastboot as usual.
Thanks again for the free support I got here. Obliged and stay blessed
Click to expand...
Click to collapse
I tried this method today and it wasn't successful. It appeared he flashed it with his auth code, but it still doesn't power on. I'm so bummed because DHL won't touch the phone for less than $151 (risk of it being sent back) because seller wants me to lie and say it's a gamepad when DHL has precautions on phones being sent back, etc. requiring importer certificates.
My phone was acting strange on 3rd day: wasn't detecting charging USB cable overnight, would only charge wirelessly. I manually rebooted a bunch of times, then it detected the USB charging and would charge. About that time I updated to Miui 13 OTA update (Chinese /EN Rom) and noticed it was rebooting randomly in my pocket asking for PIN (not getting notifications) . Again got no USB charging through cable.
I was doing a bunch of vol up/down and Power and rebooted into safe mood. Rebooted again after things were 'ok' and little while later, the phone was OFF and never came back on again.
Did I put it into EDL and brick it this way? I Never flashed anything through USB until I tried the 35eur paid service dude.
Happy to see that is being fixed.
Wish it had fixed mine. Unfortunately, it didn't . Was refunded
Help me.
my device is pixel 4xl with rooted android 13 beta 3.2 .
At first I saw on the lockscreen it said "cerficate expired" and face unlock didn't work.
I thought that if I restarted it would work again, but when I restarted the device it wouldn't turn on, I've tried pressing the power button for 1 minute, it still doesn't react, it doesn't even vibrate....
please help me to find the solution....
sinagaB said:
Help me.
my device is pixel 4xl with rooted android 13 beta 3.2 .
At first I saw on the lockscreen it said "cerficate expired" and face unlock didn't work.
I thought that if I restarted it would work again, but when I restarted the device it wouldn't turn on, I've tried pressing the power button for 1 minute, it still doesn't react, it doesn't even vibrate....
please help me to find the solution....
Click to expand...
Click to collapse
Hey! You may be on EDL mode.
To exit it you have to press power button and one of the volumes buttons, though I don't remember which one. Just have a look on Google and you will find something.
As for the certificate, I saw people having that problem if they replaced the front camera or the face id module. I don't if that's your case, but as you have root you may be able to recover face id functionality.
Let me know how it goes!
#mcl said:
Hey! You may be on EDL mode.
To exit it you have to press power button and one of the volumes buttons, though I don't remember which one. Just have a look on Google and you will find something.
As for the certificate, I saw people having that problem if they replaced the front camera or the face id module. I don't if that's your case, but as you have root you may be able to recover face id functionality.
Let me know how it goes!
Click to expand...
Click to collapse
Still didn't work :"(
Connect your phone to the PC(must be running windows). The open device manager and under the ports tab, do you see "Qualcomm HS-USB Qloader 9008 (COM *a number*)? Or something similar
#mcl said:
Connect your phone to the PC(must be running windows). The open device manager and under the ports tab, do you see "Qualcomm HS-USB Qloader 9008 (COM *a number*)? Or something similar
Click to expand...
Click to collapse
Yes , same.
sinagaB said:
Yes , same.
Click to expand...
Click to collapse
Then you are on EDL mode, as when you boot in that mode, the phone change how it shows up on the PC. You need to try to get out of there. If you can't, as you said you were having issues with the OS, maybe something is broken and the phone can't boot up.
When Android starts it has 2 bootloaders (the normal bootloader and the secondary one, which has EDL mode). If the standard bootloader fails, then it uses the second one which is EDL.
So here are some suggestions:
1. Try to hold the power key + volume up key for several seconds. If it doesn't work do the same with the volume down key
2. If that doesn't work there is another method, though it's riskier and might not work. Try to open the phone and disconnect the battery, leave it disconnected for some seconds, reconnect and try to boot the phone.
If none of those things worked for you, it means you will need to flash the firmware to your phone using EDL, as the bootloader is damaged.
Unfourtynaly there is not much info on using EDL on Pixel devices, though a lot of people use EDL to unlock Xiaomi's bootloader, so maybe have a look on those forums. On my profile, I tried to use the EDL mode to unlock a Pixel bootloader(mine is carrier-locked), though had no success, you will find a lot of helpful information to solve your problem, like the tools and files you will need and some overall idea of how EDL works.
Hope those help you and let me know if I can help you further
#mcl said:
#mcl said:
Then you are on EDL mode, as when you boot in that mode, the phone change how it shows up on the PC. You need to try to get out of there. If you can't, as you said you were having issues with the OS, maybe something is broken and the phone can't boot up.
When Android starts it has 2 bootloaders (the normal bootloader and the secondary one, which has EDL mode). If the standard bootloader fails, then it uses the second one which is EDL.
So here are some suggestions:
1. Try to hold the power key + volume up key for several seconds. If it doesn't work do the same with the volume down key
2. If that doesn't work there is another method, though it's riskier and might not work. Try to open the phone and disconnect the battery, leave it disconnected for some seconds, reconnect and try to boot the phone.
If none of those things worked for you, it means you will need to flash the firmware to your phone using EDL, as the bootloader is damaged.
Unfourtynaly there is not much info on using EDL on Pixel devices, though a lot of people use EDL to unlock Xiaomi's bootloader, so maybe have a look on those forums. On my profile, I tried to use the EDL mode to unlock a Pixel bootloader(mine is carrier-locked), though had no success, you will find a lot of helpful information to solve your problem, like the tools and files you will need and some overall idea of how EDL works.
Hope those help you and let me know if I can help you further
Click to expand...
Click to collapse
Click to expand...
Click to collapse
step 1&2 didn't work ,, by the way, thank you for replying my thread ... so there's no possible way to fix this , sir? bcause i'mnot an expert to this . )