After flashing 610M (csc: TPA) the phone shows "No sim - No service", even tough in sim card management it's there but no carrier is shown.
I tired:
1. IMEIs were there, but I still tried to restore EFS
2. Tried both sim card slots (the second one can at least receive messages, rather weird thing)
3. I tried to flash CP and CSC trough Odin after installation
4. CSC Changers do not work: errors
5. Tried to install similar ROMS: ResurectionRemix, AospExtended and crDroid... same problem over and over
6. Tried flashing latest Oxygen kernel v.5 - no luck
7. Tried installing without GAPPS - no change
8. Tried flashing latest modem from 8.1 official - nothing
Please, help me good people, I'm out of ideas. Currently using Millennium ROM, everything works. No possibility to buy a new phone, but I miss the simplicity and snappiness of AOSP roms. Thank you.
EDIT1:
I found out that even after flashing CSC in Odin. PhoneInfo app shows that there's not CSC or CSC firmware at all. Attached screenshot.
Have you tried checking if your IMEI numbers are blocked in your country?. Could be blacklisted by an operator.
From which state you are probably problem in restricting the device
TheFixerMED said:
Have you tried checking if your IMEI numbers are blocked in your country?. Could be blacklisted by an operator.
Click to expand...
Click to collapse
I use Millennium ROM (which is non-AOSP) right now, and cell service works perfectly. I can try checking of course (will reply later).
eXrump said:
I use Millennium ROM (which is non-AOSP) right now, and cell service works perfectly. I can try checking of course (will reply later).
Click to expand...
Click to collapse
Weird, I have the same model as you and I've flashed a few AOSP roms (Havoc OS, DotOS) and no problems with my signal.
Well, if it works in TW, then it could be the radio firmware in the AOSP roms that is causing the problem with your signal. Im not sure how you can flash the radio firmware once you are in an AOSP rom, but you could try making a backup of the radio related partitions with the Millenium ROM installed and then try to flash the backups once you flash an AOSP rom.
Make a full backup just in case something goes wrong.
TheFixerMED said:
Weird, I have the same model as you and I've flashed a few AOSP roms (Havoc OS, DotOS) and no problems with my signal.
Well, if it works in TW, then it could be the radio firmware in the AOSP roms that is causing the problem with your signal. Im not sure how you can flash the radio firmware once you are in an AOSP rom, but you could try making a backup of the radio related partitions with the Millenium ROM installed and then try to flash the backups once you flash an AOSP rom.
Make a full backup just in case something goes wrong.
Click to expand...
Click to collapse
Thanks for the reply. I did try to restore EFS and Modem partitions after flashing DotOS, but no luck. I looked at the *#*#4636#*#* menu; and there's a signal (decibels change). It's like it doesn't read SIM cards (I've tried another one with different carrier).
Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex
Access to the original/official firmware for SM-G900F would be extremely helpful for me as well.
I'm running LOS 16 with pico GApps very happily on my S5, however I have mobile data connectivity issues. Data connects and disconnects at random; this is device-dependent (swapping the SIM into other devices gives fully functional data connectivity).
My baseband is G900FXXU1BOA3; I believe updating the modem might fix this?
kwajongen said:
Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex
Click to expand...
Click to collapse
Fox, you may download the official firmware at https://samsung-firmware.org/model/SM-G900F/
Select your region to get the right ***.md5.tar file to flah via Odin latest.
This will reset your handheld to out of box - original recovery reinstalled - you must reflash it also via Odin if you want to go back to custom Rom..
Good luck
.
Thank you.
What would be my region?
I purchased it in the US unlocked, but US is not a choice when it comes to region.
Would I be able to see the region the phone is from from the baseband #?
Alex
kwajongen said:
Thank you.
What would be my region?
I purchased it in the US unlocked, but US is not a choice when it comes to region.
Would I be able to see the region the phone is from from the baseband #?
Alex
Click to expand...
Click to collapse
If your reference to the baseband version# is correct -> G900FXXU1ANCE, then the region is BTU -> check this address to download the original firmware:
https://samsung-firmware.org/downlo...agon-__/1806/BTU/G900FXXU1ANCE/G900FOXA1ANCE/
After flash via Odin, reboot and optional reinstall TWRP via Odin to use other custom Roms.
Are you sure you did everything before resuming to scratch. Personaly I would have done the following:
- back up in TWRP (at least data) + back up in google drive if you use google or titanium, (anyway save your picts, ...) if rooted, it is possible to save the file containing SMS, ... search in XDA,
- format (not wipe) !!!! WARNING THIS WILL ERASE ALL !!!!!
- clean install the ROM (lineageOS or else) + optional Gapps (I use Pico),
- reboot and restore data (as shown in 2 above)
(The Roms I use on my two KLTE by personal preference order are Havoc, DotOS, Bootleggers, Resurection Remix, MSM-Extended. I also use LineageOS.
Captain Kangaroo said:
If your reference to the baseband version# is correct -> G900FXXU1ANCE, then the region is BTU -> check this address to download the original firmware:
https://samsung-firmware.org/downlo...agon-__/1806/BTU/G900FXXU1ANCE/G900FOXA1ANCE/
After flash via Odin, reboot and optional reinstall TWRP via Odin to use other custom Roms.
Are you sure you did everything before resuming to scratch. Personaly I would have done the following:
- back up in TWRP (at least data) + back up in google drive if you use google or titanium, (anyway save your picts, ...) if rooted, it is possible to save the file containing SMS, ... search in XDA,
- format (not wipe) !!!! WARNING THIS WILL ERASE ALL !!!!!
- clean install the ROM (lineageOS or else) + optional Gapps (I use Pico),
- reboot and restore data (as shown in 2 above)
(The Roms I use on my two KLTE by personal preference order are Havoc, DotOS, Bootleggers, Resurection Remix, MSM-Extended. I also use LineageOS.
Click to expand...
Click to collapse
That site is very buggy, if I search my model and enter all the other info I get to Lollipop 5.0, if I click your link, although I am registered, it does not allow me to the link you provided, I mean I can get to it but when I try to login, it takes me back to the home page, so there is no way to get to your same link while being logged in.
How do I get do the download page it is a mystery to me.
Also, how do you know from the base band that it is BTU region?
Thank you
Alex
PS: I managed to use your link in IE, this site is stone age! Unbelievable, never seen a website like this, there are bugs everywhere.
kwajongen said:
That site is very buggy, if I search my model and enter all the other info I get to Lollipop 5.0, if I click your link, although I am registered, it does not allow me to the link you provided, I mean I can get to it but when I try to login, it takes me back to the home page, so there is no way to get to your same link while being logged in.
How do I get do the download page it is a mystery to me.
Also, how do you know from the base band that it is BTU region?
Thank you
Alex
PS: I managed to use your link in IE, this site is stone age! Unbelievable, never seen a website like this, there are bugs everywhere.
Click to expand...
Click to collapse
Men, the subject of resuming to firmware has been discussed and is described in the net literature! e.g. in XDA Q&A.
This discussion is now not a thread anymore but a dialog and I’m sure it will be closed by XDA moderator for redundancy.
The warnings given when you flash a custom Rom are clear. It also implies “before all” to backup, but also keep all materials to resume to original firmware, …. Now I cannot help anymore because you have problem with downloading the firmware.
Last advice – google baseband# - there are probably other web options or torrents
!!!!Also use the thanks button!!!!
kwajongen said:
Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex
Click to expand...
Click to collapse
1. Its normal to have the "Set warranty: kernel" text. As my device does too. Just simply ignore it. It won't harm your device.
2. Basically you can search websites that had official Samsung stock firmware. Search your region of your device and (IMPORTANT!) your model, in your case, is G900F. (Wow same as mine but different region, Snapdragon rocks).
3. To your network problem, I think you need to wait. There is no other option.
Thanks!
Edit: https://forum.xda-developers.com/showthread.php?t=2715487
XDA forums has one. Tip: if your region isn't there, the replies have all the filmwares you can have.
Captain Kangaroo said:
Men, the subject of resuming to firmware has been discussed and is described in the net literature! e.g. in XDA Q&A.
This discussion is now not a thread anymore but a dialog and I’m sure it will be closed by XDA moderator for redundancy.
The warnings given when you flash a custom Rom are clear. It also implies “before all” to backup, but also keep all materials to resume to original firmware, …. Now I cannot help anymore because you have problem with downloading the firmware.
Last advice – google baseband# - there are probably other web options or torrents
!!!!Also use the thanks button!!!!
Click to expand...
Click to collapse
I have downloaded the firmware and this evening I will try to upload it and see what happens.
I still I have no answer to my question: how did you figure out that my firmware is BTU?
I mean, I gave you my baseband version #: G900FXXU1ANCE and when you eventually find it in any firmware sites you are given the choice to choose among many countries, expect USA and Canada.
Since I bought the phone in the US I still wouldn't know which country the firmware is from.
Would you mind to shed some light on this?
Thank you!
Alex
OfficialJohnGL4 said:
1. Its normal to have the "Set warranty: kernel" text. As my device does too. Just simply ignore it. It won't harm your device.
Click to expand...
Click to collapse
Thank you for your feedback John.
I am not sure that message is normal, if you google it they all say it is an issue with the firmware and that you need to go back to the stock one to fix it.
Is there anyone else with lineage having that same message?
Also, when I try to format my SD Card, it gets stuck to 40% and then it goes to the homepage.
I tried also a brand new card, same story.
It gives a message but it goes away after a few secs., I believe it is a Java message, but I can try again and take a picture of it.
Thank you,
Alex
kwajongen said:
I have downloaded the firmware and this evening I will try to upload it and see what happens.
I still I have no answer to my question: how did you figure out that my firmware is BTU?
I mean, I gave you my baseband version #: G900FXXU1ANCE and when you eventually find it in any firmware sites you are given the choice to choose among many countries, expect USA and Canada.
Since I bought the phone in the US I still wouldn't know which country the firmware is from.
Would you mind to shed some light on this?
Thank you!
Alex
Click to expand...
Click to collapse
I tell you my experience:
No matter the country you bought your device. As example, I leave in France, I bought mine in Hong-Kong, but choose an international device (G900F).
Before flashing anything, I checked all information in settings and recovery.
Pict below is original out of box G900FXXU1BOC7
Recovery information after latest update G900FXXS1CQD1
It happened recently 2 times my device was stuck because encription issues – I recover by reflashing original G900FXXU1BOC7 via Odin
I personally downloaded firmware as G900F – BTU, because I check the version at each updates and this sticked to BTU ONLY.
May be the site SamMobile will be more meaningful for you, because you see Countries/Operators and updates history.
https://www.sammobile.com/samsung/galaxy-s5/firmware/SM-G900F/BTU/
For your device, you have to grab the search to find the closest original (which you have) to latest update (if you have it).
For the Kernel yellow tag at warmup, this is done when you flash TWRP. No issues since 2 years operation with that using LineageOS, Havoc, DotOS, AOSP, Bootleggers, RR, ViperOS. If you flash original firmware, it will disappear because twrp is erased and original stock recovery flashed.
kwajongen said:
Thank you for your feedback John.
I am not sure that message is normal, if you google it they all say it is an issue with the firmware and that you need to go back to the stock one to fix it.
Is there anyone else with lineage having that same message?
Also, when I try to format my SD Card, it gets stuck to 40% and then it goes to the homepage.
I tried also a brand new card, same story.
It gives a message but it goes away after a few secs., I believe it is a Java message, but I can try again and take a picture of it.
Thank you,
Alex
Click to expand...
Click to collapse
When it said that you go back to stock one to fix it. Then want if it is not stock? The message is still there. Its normal if you want to install a custom ROM other than the stock one. I reinstall the stock and install custom ROM again once. It still happened.
I don't know how to remove the text but still have a custom ROM tho.
As for the SD card message, I encountered times before. Maybe you need to format using the computer.
Captain Kangaroo said:
I tell you my experience:
No matter the country you bought your device. As example, I leave in France, I bought mine in Hong-Kong, but choose an international device (G900F).
Before flashing anything, I checked all information in settings and recovery.
Pict below is original out of box G900FXXU1BOC7
Recovery information after latest update G900FXXS1CQD1
It happened recently 2 times my device was stuck because encription issues – I recover by reflashing original G900FXXU1BOC7 via Odin
I personally downloaded firmware as G900F – BTU, because I check the version at each updates and this sticked to BTU ONLY.
May be the site SamMobile will be more meaningful for you, because you see Countries/Operators and updates history.
https://www.sammobile.com/samsung/galaxy-s5/firmware/SM-G900F/BTU/
For your device, you have to grab the search to find the closest original (which you have) to latest update (if you have it).
For the Kernel yellow tag at warmup, this is done when you flash TWRP. No issues since 2 years operation with that using LineageOS, Havoc, DotOS, AOSP, Bootleggers, RR, ViperOS. If you flash original firmware, it will disappear because twrp is erased and original stock recovery flashed.
Click to expand...
Click to collapse
When I reflash the stock ROM TWRP is still there. However no "Set warranty: kernel" appeared. Maybe its just when you install a custom ROM or something, I don't know.
OK guys,
Lineage 16 is installed, everything went smoothly, however when I connect the USB, the phone just shows as 'SM-G900F' on my W10 PC and cannot be expanded, basically no Phone and SD Card folders.
I can see them in the phone no problem, but once I connect it, I am not prompted with the usual message on what I want to do, like file transfer etc. and on the left menu appears only the model of the phone.
I had no issues when I flashed the original firmware, so it must be related to Lineage.
I also installed the Android USB drivers, but no go.
Changing the USB Preferences, to PTP or File Transfer only allows me to see the phone, no SD.
I also tried a new SD, no success.
I am stuck again... Jeez it takes days to get this stuff to work, you do one step ahead and another back
Ideas?
Alex
Anyone?
Shall I ask the question in the Lineage section?
'Set warranty :kernel' means you are running a custom kernel. Any modified boot.IMG can cause this message. It doesn't mean you need to use stock room. This appears even in stock rom with magisk or SuperSU.