SM-G900F - Need original firmware - Galaxy S 5 General

Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex

Access to the original/official firmware for SM-G900F would be extremely helpful for me as well.
I'm running LOS 16 with pico GApps very happily on my S5, however I have mobile data connectivity issues. Data connects and disconnects at random; this is device-dependent (swapping the SIM into other devices gives fully functional data connectivity).
My baseband is G900FXXU1BOA3; I believe updating the modem might fix this?

kwajongen said:
Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex
Click to expand...
Click to collapse
Fox, you may download the official firmware at https://samsung-firmware.org/model/SM-G900F/
Select your region to get the right ***.md5.tar file to flah via Odin latest.
This will reset your handheld to out of box - original recovery reinstalled - you must reflash it also via Odin if you want to go back to custom Rom..
Good luck
.

Thank you.
What would be my region?
I purchased it in the US unlocked, but US is not a choice when it comes to region.
Would I be able to see the region the phone is from from the baseband #?
Alex

kwajongen said:
Thank you.
What would be my region?
I purchased it in the US unlocked, but US is not a choice when it comes to region.
Would I be able to see the region the phone is from from the baseband #?
Alex
Click to expand...
Click to collapse
If your reference to the baseband version# is correct -> G900FXXU1ANCE, then the region is BTU -> check this address to download the original firmware:
https://samsung-firmware.org/downlo...agon-__/1806/BTU/G900FXXU1ANCE/G900FOXA1ANCE/
After flash via Odin, reboot and optional reinstall TWRP via Odin to use other custom Roms.
Are you sure you did everything before resuming to scratch. Personaly I would have done the following:
- back up in TWRP (at least data) + back up in google drive if you use google or titanium, (anyway save your picts, ...) if rooted, it is possible to save the file containing SMS, ... search in XDA,
- format (not wipe) !!!! WARNING THIS WILL ERASE ALL !!!!!
- clean install the ROM (lineageOS or else) + optional Gapps (I use Pico),
- reboot and restore data (as shown in 2 above)
(The Roms I use on my two KLTE by personal preference order are Havoc, DotOS, Bootleggers, Resurection Remix, MSM-Extended. I also use LineageOS.

Captain Kangaroo said:
If your reference to the baseband version# is correct -> G900FXXU1ANCE, then the region is BTU -> check this address to download the original firmware:
https://samsung-firmware.org/downlo...agon-__/1806/BTU/G900FXXU1ANCE/G900FOXA1ANCE/
After flash via Odin, reboot and optional reinstall TWRP via Odin to use other custom Roms.
Are you sure you did everything before resuming to scratch. Personaly I would have done the following:
- back up in TWRP (at least data) + back up in google drive if you use google or titanium, (anyway save your picts, ...) if rooted, it is possible to save the file containing SMS, ... search in XDA,
- format (not wipe) !!!! WARNING THIS WILL ERASE ALL !!!!!
- clean install the ROM (lineageOS or else) + optional Gapps (I use Pico),
- reboot and restore data (as shown in 2 above)
(The Roms I use on my two KLTE by personal preference order are Havoc, DotOS, Bootleggers, Resurection Remix, MSM-Extended. I also use LineageOS.
Click to expand...
Click to collapse
That site is very buggy, if I search my model and enter all the other info I get to Lollipop 5.0, if I click your link, although I am registered, it does not allow me to the link you provided, I mean I can get to it but when I try to login, it takes me back to the home page, so there is no way to get to your same link while being logged in.
How do I get do the download page it is a mystery to me.
Also, how do you know from the base band that it is BTU region?
Thank you
Alex
PS: I managed to use your link in IE, this site is stone age! Unbelievable, never seen a website like this, there are bugs everywhere.

kwajongen said:
That site is very buggy, if I search my model and enter all the other info I get to Lollipop 5.0, if I click your link, although I am registered, it does not allow me to the link you provided, I mean I can get to it but when I try to login, it takes me back to the home page, so there is no way to get to your same link while being logged in.
How do I get do the download page it is a mystery to me.
Also, how do you know from the base band that it is BTU region?
Thank you
Alex
PS: I managed to use your link in IE, this site is stone age! Unbelievable, never seen a website like this, there are bugs everywhere.
Click to expand...
Click to collapse
Men, the subject of resuming to firmware has been discussed and is described in the net literature! e.g. in XDA Q&A.
This discussion is now not a thread anymore but a dialog and I’m sure it will be closed by XDA moderator for redundancy.
The warnings given when you flash a custom Rom are clear. It also implies “before all” to backup, but also keep all materials to resume to original firmware, …. Now I cannot help anymore because you have problem with downloading the firmware.
Last advice – google baseband# - there are probably other web options or torrents
!!!!Also use the thanks button!!!!

kwajongen said:
Hi guys,
My S5 was on 6.0 and have upgraded to 9 Pie but something went wrong (or I screwed up something) and I need to re-upload the original firmware, unless you have better suggestion.
Currently, I have TWRP installed as well as Android 9, however, when I turn my S5 on, I get: Set Warranty Bit:Kernel
It stays there for 30 secs then the phone boots up and everything looks fine, it connects to wi-fi etc.
One other strange thing is that I get a message on the home screen saying: unsupported SanDisk SD Card
I tried a new one, same message.
Before I started this process, I connected the phone to my PC and copied both the Phone and the Card folders, so I am good, data wise.
Basically I was thinking to go back to the very first OS, I think 4.4.2 and then re-load Lineage 16 using TWRP.
If I read the baseband version # is: G900FXXU1ANCE
If the procedure above is correct, would you be able to provide me a link to download the firmware?
I tried all the known sites, but their speed sucks, so I thought to ask here as somebody may have a link.
I will use Odin latest version to install it.
Thank you!
Alex
Click to expand...
Click to collapse
1. Its normal to have the "Set warranty: kernel" text. As my device does too. Just simply ignore it. It won't harm your device.
2. Basically you can search websites that had official Samsung stock firmware. Search your region of your device and (IMPORTANT!) your model, in your case, is G900F. (Wow same as mine but different region, Snapdragon rocks).
3. To your network problem, I think you need to wait. There is no other option.
Thanks!
Edit: https://forum.xda-developers.com/showthread.php?t=2715487
XDA forums has one. Tip: if your region isn't there, the replies have all the filmwares you can have.

Captain Kangaroo said:
Men, the subject of resuming to firmware has been discussed and is described in the net literature! e.g. in XDA Q&A.
This discussion is now not a thread anymore but a dialog and I’m sure it will be closed by XDA moderator for redundancy.
The warnings given when you flash a custom Rom are clear. It also implies “before all” to backup, but also keep all materials to resume to original firmware, …. Now I cannot help anymore because you have problem with downloading the firmware.
Last advice – google baseband# - there are probably other web options or torrents
!!!!Also use the thanks button!!!!
Click to expand...
Click to collapse
I have downloaded the firmware and this evening I will try to upload it and see what happens.
I still I have no answer to my question: how did you figure out that my firmware is BTU?
I mean, I gave you my baseband version #: G900FXXU1ANCE and when you eventually find it in any firmware sites you are given the choice to choose among many countries, expect USA and Canada.
Since I bought the phone in the US I still wouldn't know which country the firmware is from.
Would you mind to shed some light on this?
Thank you!
Alex

OfficialJohnGL4 said:
1. Its normal to have the "Set warranty: kernel" text. As my device does too. Just simply ignore it. It won't harm your device.
Click to expand...
Click to collapse
Thank you for your feedback John.
I am not sure that message is normal, if you google it they all say it is an issue with the firmware and that you need to go back to the stock one to fix it.
Is there anyone else with lineage having that same message?
Also, when I try to format my SD Card, it gets stuck to 40% and then it goes to the homepage.
I tried also a brand new card, same story.
It gives a message but it goes away after a few secs., I believe it is a Java message, but I can try again and take a picture of it.
Thank you,
Alex

kwajongen said:
I have downloaded the firmware and this evening I will try to upload it and see what happens.
I still I have no answer to my question: how did you figure out that my firmware is BTU?
I mean, I gave you my baseband version #: G900FXXU1ANCE and when you eventually find it in any firmware sites you are given the choice to choose among many countries, expect USA and Canada.
Since I bought the phone in the US I still wouldn't know which country the firmware is from.
Would you mind to shed some light on this?
Thank you!
Alex
Click to expand...
Click to collapse
I tell you my experience:
No matter the country you bought your device. As example, I leave in France, I bought mine in Hong-Kong, but choose an international device (G900F).
Before flashing anything, I checked all information in settings and recovery.
Pict below is original out of box G900FXXU1BOC7
Recovery information after latest update G900FXXS1CQD1
It happened recently 2 times my device was stuck because encription issues – I recover by reflashing original G900FXXU1BOC7 via Odin
I personally downloaded firmware as G900F – BTU, because I check the version at each updates and this sticked to BTU ONLY.
May be the site SamMobile will be more meaningful for you, because you see Countries/Operators and updates history.
https://www.sammobile.com/samsung/galaxy-s5/firmware/SM-G900F/BTU/
For your device, you have to grab the search to find the closest original (which you have) to latest update (if you have it).
For the Kernel yellow tag at warmup, this is done when you flash TWRP. No issues since 2 years operation with that using LineageOS, Havoc, DotOS, AOSP, Bootleggers, RR, ViperOS. If you flash original firmware, it will disappear because twrp is erased and original stock recovery flashed.

kwajongen said:
Thank you for your feedback John.
I am not sure that message is normal, if you google it they all say it is an issue with the firmware and that you need to go back to the stock one to fix it.
Is there anyone else with lineage having that same message?
Also, when I try to format my SD Card, it gets stuck to 40% and then it goes to the homepage.
I tried also a brand new card, same story.
It gives a message but it goes away after a few secs., I believe it is a Java message, but I can try again and take a picture of it.
Thank you,
Alex
Click to expand...
Click to collapse
When it said that you go back to stock one to fix it. Then want if it is not stock? The message is still there. Its normal if you want to install a custom ROM other than the stock one. I reinstall the stock and install custom ROM again once. It still happened.
I don't know how to remove the text but still have a custom ROM tho.
As for the SD card message, I encountered times before. Maybe you need to format using the computer.
Captain Kangaroo said:
I tell you my experience:
No matter the country you bought your device. As example, I leave in France, I bought mine in Hong-Kong, but choose an international device (G900F).
Before flashing anything, I checked all information in settings and recovery.
Pict below is original out of box G900FXXU1BOC7
Recovery information after latest update G900FXXS1CQD1
It happened recently 2 times my device was stuck because encription issues – I recover by reflashing original G900FXXU1BOC7 via Odin
I personally downloaded firmware as G900F – BTU, because I check the version at each updates and this sticked to BTU ONLY.
May be the site SamMobile will be more meaningful for you, because you see Countries/Operators and updates history.
https://www.sammobile.com/samsung/galaxy-s5/firmware/SM-G900F/BTU/
For your device, you have to grab the search to find the closest original (which you have) to latest update (if you have it).
For the Kernel yellow tag at warmup, this is done when you flash TWRP. No issues since 2 years operation with that using LineageOS, Havoc, DotOS, AOSP, Bootleggers, RR, ViperOS. If you flash original firmware, it will disappear because twrp is erased and original stock recovery flashed.
Click to expand...
Click to collapse
When I reflash the stock ROM TWRP is still there. However no "Set warranty: kernel" appeared. Maybe its just when you install a custom ROM or something, I don't know.

OK guys,
Lineage 16 is installed, everything went smoothly, however when I connect the USB, the phone just shows as 'SM-G900F' on my W10 PC and cannot be expanded, basically no Phone and SD Card folders.
I can see them in the phone no problem, but once I connect it, I am not prompted with the usual message on what I want to do, like file transfer etc. and on the left menu appears only the model of the phone.
I had no issues when I flashed the original firmware, so it must be related to Lineage.
I also installed the Android USB drivers, but no go.
Changing the USB Preferences, to PTP or File Transfer only allows me to see the phone, no SD.
I also tried a new SD, no success.
I am stuck again... Jeez it takes days to get this stuff to work, you do one step ahead and another back
Ideas?
Alex

Anyone?
Shall I ask the question in the Lineage section?

'Set warranty :kernel' means you are running a custom kernel. Any modified boot.IMG can cause this message. It doesn't mean you need to use stock room. This appears even in stock rom with magisk or SuperSU.

Related

Which firmware should I flash on my new SGS?

My new SGS just got delivered today, bought it brand new from ebay, it is unlocked but from orange so there are a few orange bloatware apps like maps etc, not happy with these and want them gone but after trying kies it says my firmware cannot be updated (maybe due to being branded)?
Anyway just wondering which of the unofficial firmwares to flash from the samsung-firmwares website, I understand they come with certain files that may put phone into russian or make it so market does not work properly, some advice on this matter would be appreciated, I'm in UK if that helps. Cheers lads.
Oh and my current versions are
PDA I9000XXJF3
PHONE I9000XXJF3
CSC I9000RAJE5
Hi Davey,
I've just done mine for the first time tonight. I used firmware JG1, but used the CSC file suggested on the main thread firmware thread (cant do a link, forum wont let me).
A couple of notes - I originally tried using a front USB port on my machine and it stuck on file analysis. Worked better when I plugged it in round the back. Secondly, mine showed up on COM5 not 7 as in the guides but it seemed to make no difference.
Good luck!
Cheers pal, jsut wondering have you had any issues with the firmware you used? Russian language? Paid apps not showing up in market? Thanks.
No russian as long as you use the separate CSC firmware (CSC_I9000OXXJF9), and no other issues other than swype crashing the first time I tried to use (restarted the phone, problem solved).
Some apps arent showing up though in market, and I think a root is needed to fix it unfortunately. Not a big deal though - if you're willing to attempt the firmware, than I doubt rooting is a particularly big deal.
I'm in a similar position. T-Mobile UK, galaxy to arrive tomorrow.
I've seen several people complaining about lag on the phone until a firmware upgrade. Could someone point me to a post/website that gives a list of the latest firmwares and a step-by-step guide to installing them on the phone.
Thanks
same here, i have found a few rooting + firmware article from other websites / blogs.
however I only trust the guides from XDAdevelopers
kohog said:
I'm in a similar position. T-Mobile UK, galaxy to arrive tomorrow.
I've seen several people complaining about lag on the phone until a firmware upgrade. Could someone point me to a post/website that gives a list of the latest firmwares and a step-by-step guide to installing them on the phone.
Thanks
Click to expand...
Click to collapse
http://www.samsung-firmwares.com (register, login and select "i9000" from the list, the firmware files and guides are on the same page, as are the links to dowload the required tools).
I am on UK T-Mobile and have followed these videos in the order listed and have had no problems doing so:
http://www.youtube.com/watch?v=PpWcM44On88
http://www.youtube.com/watch?v=VzFE8-jWku0
The above is to update the firmware, the only thing I did that was not on the video was to use a different CSC file (Not the Russian one, I used CSC_I9000OXXJF9), doing it this way, I had no problems with using Swype as some have reported.
I then applied Paul's Custom ROM R2 from Modaco (Great Job) - the update roots the phone so you do not have to. It is all worth it as now my GPS, Wifi and speed all work wonderfully. the video of how to update the Custom Rom is here:
http://www.youtube.com/watch?v=uakGtQKmHNM
Remember to restart the phone after updating the firmware and also after updating the Custom ROM. Also make sure that you have installed the latest version of Samsung's KIES software which contains the drivers needed for the SGS. Also if you carry out this part, make sure you copy the update.zip file to the internal memory card for update to work as it fails to read from the external one.
I did all this on a Notebook running Vista 32bit without any problems.

[Q] No call sound after back to stock

Hi guys,
I know there are many similiar threads to this one and I'm sure I've read most of them. Either my issue is different, or, if the answer was in one of them, I was too stupid to realize it.
With my S4 Active GT-I9295 I had to go back to stock ROM for the Samsung S-Health and Gear related apps.
I came from spegelius' (absolutely awesome) Google Edition for SGS4A (int'l) v0.9.9.-od2 and flashed the Samsung Stock 4.4.2 with Odin (*). The procedure was: Flash -> Factory Reset -> Flash again to be absolutely sure all files are updated. Currently, I rooted the phone.
My problem persists:
After a reboot I (usually; not always) am able to make normal phone calls.
After some time (sometimes minutes, sometimes hours) I no longer have sound.
I do not hear ringing, the callee can't hear me, I can't hear the callee.
Same problem if I'm being called
Establishing a connection though works always.
Mobile Data is not affected.
WiFi works
Also observed after factory reset -> re-flash, only enter WiFi PW and Google Login Data -> try phone call
I know this problem often arises from a baseband/modem mismatch. So I investigated my CWM backup of the pre-installed 4.2.2 ROM.
That's what was pre-installed:
Bootloader: I9295XXUBMK3
CSC: I9295OXXBMK3
Modem: *I did not find the info in my backup*
This corresponds to the Romanian 4.2.2: http://www.sammobile.com/firmwares/download/22586/I9295XXUBMK3_I9295OXXBMK3_ROM.zip/
That's why I flashed the direct successor http://www.sammobile.com/firmwares/download/37083/I9295XXUCNI1_I9295OXXCNI1_ROM.zip/
PDA: I9295XXUCNI1
CSC: I9295OXXCNI1
MODEM: I9295XXUCNI1
I tried everything I could find online, nothing helped. I am really running out of ideas. Is it possible to go back to 4.2.2 to see if the problem persists?
I do have logcat logs of the radio module before and after the problem occured. But its thousands of lines. If it helps I can upload it!
Thank you guys for your help
(*): I did some intermediate flashing of several other firmware versions (especially different baseband / CSC versions of the same 4.4.2). But I assume this does not affect the result. I used Odin v3.07 & v3.09
Edit: PS: I still think that I might have the wrong CSC Version. I know the 4.2.2 PDA/CSC matches, but I am not from Romania. I'm actually from Germany. And what makes me wonder is that I cannot select the German Keyboard Style without downloading it first. I can't remember doing something similar after unboxing the phone and setting it up for the first time.
Are you aware of this thread?
http://forum.xda-developers.com/showthread.php?p=56955843
Bevare the Thanks Button
Thanks for the answer O-T!
Yes, I was aware of that thread. However, I never made it until here
http://forum.xda-developers.com/showthread.php?p=50787570
Although I did the things basically as described in that posts I have a new question:
Which country is relevant for the search on sammobile? I mean, do they ask me "Where do you live" or "For which country was your device produced?".
Edit: Okay actually they ask me for the 'product code', so it's probably the latter question.
I realized that my 4.2.2 PDA and CSC also match the French version. That would match the language of my original packaging. I already flashed the French 4.4.2 once but heard only noise when calling someone. So I gave up on that one quickly. But I'll give it another shot now.
Is it possible that I had a factory installation of the firmware for country A, and when I first registered with my local carrier I received a modem update OTA for country B?
That would really surprise me. But it could explain my issues, since there is no 4.4.2 for o2 Germany, i.e. I probably wouldn't receive another modem update OTA.
(I never looked into the carrier specific firmwares because I figured they are for sim-locked devices.)
If the above is true, I understand that the only option would be to somehow downgrade my device back to 4.2.2.
I know I'm asking a lot of questions that have been asked and answered elsewhere. But by now I tried so much and nothing worked that I'm really confused and need your guidance.
I know I type too much, so a short summary.
Everything I tried so far didn't help, the stock ROM from sammobile.com doesn't help, currently I'm on 4.4.2 XEF (France)
I'm 80% sure I have the firmware for the correct country
From factory-side I definitely had an XX PDA and OXX CSC, so shouldn't all XX/OXX versions work, even if not the exact country?
What should I try next?
Is there a way to uniquely identify the country code from a backup of the /system or /data parition?
hyperion89 said:
I know I type too much, so a short summary.
Everything I tried so far didn't help, the stock ROM from sammobile.com doesn't help, currently I'm on 4.4.2 XEF (France)
I'm 80% sure I have the firmware for the correct country
From factory-side I definitely had an XX PDA and OXX CSC, so shouldn't all XX/OXX versions work, even if not the exact country?
What should I try next?
Is there a way to uniquely identify the country code from a backup of the /system or /data parition?
Click to expand...
Click to collapse
I am not sure if you have done this, but one thing I always recommend is a phone factory reset from settings (not CWM/TWRP) when you are on stock firmware as this is known to correct a lot of issues caused mainly due to faulty partition / corruption. However beware of the fact that this will wipe your internal SD card therefore back it up before you do that.
If you have flashed the correct firmware for your country & carrier (if it has a separate one) where you are using the phone, and done the above then I do no see any other issue than a faulty IC that requires replacement
JASONRR said:
I am not sure if you have done this, but one thing I always recommend is a phone factory reset from settings (not CWM/TWRP) when you are on stock firmware as this is known to correct a lot of issues caused mainly due to faulty partition / corruption. However beware of the fact that this will wipe your internal SD card therefore back it up before you do that.
Click to expand...
Click to collapse
Yes, I always did a factory reset. Most of the times I even flashed the firmware a second time after the factory reset. (This was recommended somewhere else.)
JASONRR said:
If you have flashed the correct firmware for your country & carrier (if it has a separate one) where you are using the phone, and done the above then I do no see any other issue than a faulty IC that requires replacement
Click to expand...
Click to collapse
Now that really helps me! Thanks. BUT: There is a seperate firmware for my carrier. However, I did not purchase the phone from that carrier. That's why I never tested the carrier specific firmware. Moreover, there is only the old 4.2.2 available, so I can't test it, since I cannot downgrade.
hyperion89 said:
Now that really helps me! Thanks. BUT: There is a seperate firmware for my carrier. However, I did not purchase the phone from that carrier. That's why I never tested the carrier specific firmware. Moreover, there is only the old 4.2.2 available, so I can't test it, since I cannot downgrade.
Click to expand...
Click to collapse
You can flash only the modem & non-holos from the 4.2.2 firmware and check
JASONRR said:
You can flash only the modem & non-holos from the 4.2.2 firmware and check
Click to expand...
Click to collapse
Tried it and it didn't work; completely crashed my Phone Application. It rang on the other side, but no conversation was possible. Is this because of the bootloader / modem mismatch?
Does anyone have instructions to safely downgrade to 4.2.2 again? Should I open another thread for this discussion?
hyperion89 said:
Tried it and it didn't work; completely crashed my Phone Application. It rang on the other side, but no conversation was possible. Is this because of the bootloader / modem mismatch?
Does anyone have instructions to safely downgrade to 4.2.2 again? Should I open another thread for this discussion?
Click to expand...
Click to collapse
Identify the bootloader version and Knox state:
http://forum.xda-developers.com/showthread.php?p=57332718
Knox is not a counter - it's a like a fuse.
Hi O-T,
the bootloader is I9295XXUBMK3 and it does not yet have the warranty bit which I assume you mean by KNOX state.
Are there maybe any new ideas?
hyperion89 said:
Hi O-T,
the bootloader is I9295XXUBMK3 and it does not yet have the warranty bit which I assume you mean by KNOX state.
Are there maybe any new ideas?
Click to expand...
Click to collapse
There's 3 stock 4.2.2 TW ROM I9295XXUBMK3 to choose for flash by Odin. All have different Germany CSC (Carrier Specific Code) - Generic, O2, T-Mobile. PDA=MODEM=I9295XXUBMK3 for all of them. Not sure if O2 or T-Mobile versions are locked, but they usually have operators bloat apps.
Remember to power OFF before entering download mode, flash ROM in Odin, factory reset.
https://www.samdownloads.de/download/i9295xxubmk3-dbt-4-2-2-germany/
https://www.samdownloads.de/download/i9295xxubmk3-via-4-2-2-germany-o2/
https://www.samdownloads.de/download/i9295xxubmk3-dtm-4-2-2-germany-t-mobile/
Your choice.
O-T I'm so sorry. My post from yesterday was a lie; I can't read my own OP. :crying: :angel:
I9295XXUBMK3 was preinstalled
Now I'm on I9295XXUCNH2, which implies 4.4.2 and makes a downgrade to 4.2.2 impossible (afaik).
Please note that I already tried the generic German (4.4.2) firmware. I never had operater bloat apps and I bought a simlock-free version of the device. Thus I never tested the o2 / T-Mobile ones. (I did, however, once flash the o2 modem over the generic 4.4.2, which turned out to be a bad idea).
I would love to extract the modem info from my CWM backup. The bootloader / CSC strongly suggest I have a French phone, but the modem would ultimately clarify that.
What is your opinion on trying a different custom-ROM? I never built one so I have no idea from where designers obtain their NON-HLOS and modem files. I know many don't come with any of those and require an already working ROM before flashing so these drivers can be kept. On the other hand, Darkman's StockyROM has an additional modem pack.... which, in my case, didn't help.
I simply cannot believe that it's a hardware issue. Everything worked fine until the update to 4.4.2 and new radio drivers should be thoroughly tested before distribution.

G800F back cover warning

Hello, i bought my phone ages ago. No problems what so ever(exept gone through 2 new batteries already, but i assume its my idiocy).
Gone through rooting, CM12 (5.0.0 (LP) i believe?) and then installed original fresh ROM. Now factory settings and not rooted for last 6 months or so.
At Christmas i bought myself a flip cover with fancy little useless window (known as S-View).
Installed it and everything looked good until few hours later, phone started popping back cover warnings, everytime i unlock the phone.
Then got it worse, phone started to woke up itself and pop up the warning, then lock itself again and over and over again.
Removing the cover worked, then i installed it and it worked again. Then i changed SD and it started that sh*t again!
So i bought new SD card hoping it will solve situation (ADATA 64GB, UHS1, Class10) after reading stuff about frying SD cards and error codes that trigger the warning.
Here i am, phone keeps doing that over and over again. Thought i would find help in here, or somewhere else, but no good.
Can someone help me?
Phone is used, last owner "didnt fully ulitized its functions" so he sold it to me. Phone runs on 4.4.2 (KK) which is kinda sad for me, because i keep waiting for official update (im stupid).
Could some custom kernel solve this? I like TouchWiz (bash me again) and i found having native functions (like sensors, ir controller, screensharing and other comfy fat stuff built in) rather usefull than bloatware, so thats why i left CM.
Any help appreciated. And excuse my english.
Same problem, on 4.4.2 without root and waiting for official update. I have tried every advice from the internet to no avail.
I have learned to live with it and hope that with a firmware update it will go away.
So, I don't know why you have this problem (I never bought a flip cover for my phone,I hate it), but you are for the third time (I think) a stupid (no offense) because now there's the CM13 with a bit more feature supported than CM12. However you can try to flash Touchwiz 5.1.1 and see what happen, if you didn't yet. It doesn't matter if the update it isn't released yet for your country, just flash an update for the G800F.
If you are root you can use the link2sd app and freeze a system app called PopupuiReceiver and the back cover warning will dissapear.
I hope this helps you. Sorry for my English.
Enviado desde mi SM-G800F usando Tapatalk 2
Andrea224 said:
However you can try to flash Touchwiz 5.1.1 and see what happen, if you didn't yet. It doesn't matter if the update it isn't released yet for your country, just flash an update for the G800F.
Click to expand...
Click to collapse
It's not released worldwide yet, or there should be something on sammobile about it...
Forgot to mention i got a G800FXXU1AOG2 and official release wasnt mentioned on Youmobile either.
I dont wanna lose all my data, just because stupid popup tho. Do all the prep and work just for "hope" it will be solved..
Atleast thanks, will keep that in mind.
groubal said:
It's not released worldwide yet, or there should be something on sammobile about it...
Forgot to mention i got a G800FXXU1AOG2 and official release wasnt mentioned on Youmobile either.
I dont wanna lose all my data, just because stupid popup tho. Do all the prep and work just for "hope" it will be solved..
Atleast thanks, will keep that in mind.
Click to expand...
Click to collapse
Ehy man, Youmobile didn't say nothing yet but they are 100% official and you will not lose your data if you download Cyprus 5.1.1 and flash it via Odin. You can find all 5.1.1 release on Sammobile and if you download a Vodafone branded rom you need a PIT file. Try it.
Andrea224 said:
Ehy man, Youmobile didn't say nothing yet but they are 100% official and you will not lose your data if you download Cyprus 5.1.1 and flash it via Odin. You can find all 5.1.1 release on Sammobile and if you download a Vodafone branded rom you need a PIT file. Try it.
Click to expand...
Click to collapse
I got T-mobile(sim) but completelly operator-free rom and i would like to make it, like it is.
In another words, can you tell me if the other xxxxBOLx versions will work instead of my xxxxAOlx version?
I'll go for operator free, as i mentioned before, so the "PDA" version as sammobile says is the only one thing that bugs me about flashing my phone.
groubal said:
I got T-mobile(sim) but completelly operator-free rom and i would like to make it, like it is.
In another words, can you tell me if the other xxxxBOLx versions will work instead of my xxxxAOlx version?
I'll go for operator free, as i mentioned before, so the "PDA" version as sammobile says is the only one thing that bugs me about flashing my phone.
Click to expand...
Click to collapse
The only thing that i can say to you is that i flashed the Italy Vodafone rom (with PIT file) and it works well. (I'm from Italy so you can understand). However every G800F rom can be flashed (with PIT file if it's a branded rom like Vodafone). This rom has G800FXXU1BOL4 version and it works with every G800F. So, I recommend you the Cyprus one because is no-branded and it doesn't need the PIT (also the Germany no-branded one but is less updated). However you can install the Vodafone one but you need the PIT file. (and I can give it to you)
Andrea224 said:
So, I recommend you the Cyprus one because is no-branded and it doesn't need the PIT (also the Germany no-branded one but is less updated). However you can install the Vodafone one but you need the PIT file. (and I can give it to you)
Click to expand...
Click to collapse
Thats what i wanted to hear. Thanks :good:
So today i tried to flash. Successfully. System looks like it has more stability built in, visually, its almost like KK. The popup seems to be gone. Only one thing that surprised me "Google Play Service Error" which tends to stay in loop. Uninstaled and reinstalled, hopefully it will work. Sadly Cyprus is a Vodafone. So gonna find another, less annoying rom - Germany, atleast until my country gets official release.
For those who wanna flash, use AP tab in Odin (if you ever flashed before, the tab was called "PDA" now its AP - "Android Phone") and let the phone deal with itself, i panicked and reflashed twice, just because i was nervous.
Happy Easter.
Another edit: The German ROM has everyday bloatware in, however, it can be uninstalled without much pain, by simply dragging it up -> Uninstall. So far, so good. Cheers.
groubal said:
So today i tried to flash. Successfully. System looks like it has more stability built in, visually, its almost like KK. The popup seems to be gone. Only one thing that surprised me "Google Play Service Error" which tends to stay in loop. Uninstaled and reinstalled, hopefully it will work. Sadly Cyprus is a Vodafone. So gonna find another, less annoying rom.
For those who wanna flash, use AP tab in Odin (if you ever flashed before, the tab was called "PDA" now its AP - "Android Phone") and let the phone deal with itself, i panicked and reflashed twice, just because i was nervous.
Happy Easter.
Click to expand...
Click to collapse
Nice,however Vodafone's ROMs is more updated than other ROMs.

Optimus L90 Unable to Root, Unable to boot into recovery mode

Hi
I have gone through the forums and can't seem to find solution for my problem with my Optimus L90 phone.
I have recently flashed the CM13 on my phone without any errors but below are the issues that I am facing
1. No cellular network signal after inserting SIM card.
2. I read in a different forum that this could happen due to using a wrong version of TWRP, so installed a newer version 2.8.7.0 but things worse.
3. Now I am not able to boot into recovery mode and phone just stays idle with the LG logo screen and few commands appearing like fastboot_iniy() and udc_start().
4. I have tried hard reset and soft reset and both are not successful.
5. I cannot root my phone either. Tried all ways like towelroot, purpledrake, lg root by avicoh etc but in vain
Now my phone, even though has a latest CM version I cannot use it for anything else.
Any help is greatly appreciated.
No SIM is hardly related to TWRP, probably you needed a different bootstack (there is a thread about it).
On CM you don't need anything to root, it's already rooted just not visible to common users, you need to activate Developer Options (it's also explained elsewhere)
Finally, if you cannot reach recovery but still can boot CM13 simply use adb, Flashfy or Hashr to flash another version or TWRP. 2.8.7 is kinda old and not recommended for Marshmallow, you can try 3.0.2 by SlimShady or DarkBlue version from shoxxy's thread.
Thanks for the reply, let me try options you have specified and get back if I am still facing issues
hvramanan said:
Thanks for the reply, let me try options you have specified and get back if I am still facing issues
Click to expand...
Click to collapse
I was able to unblock my phone finally and loaded the stock ROM but the phone is still isn't recognizing cellular network . I am on T-MOBILE. I have tried to insert different SIM, turned off wifi calling but still the phone is not catching any cellular network.
[lfom]: you indicated earlier that a different bootstack might be needed. I am not that knowledgeable about bootstack so can you help me through this or point me to different thread where users might have a similar issue.
Sorry, I meant to say unbrick above
Everything one needs or wants to know about bootstack is here:
http://forum.xda-developers.com/lg-l90/development/bootstack-kk-l-l90-t3118632
lfom said:
Everything one needs or wants to know about bootstack is here:
http://forum.xda-developers.com/lg-l90/development/bootstack-kk-l-l90-t3118632
Click to expand...
Click to collapse
Hi,
I followed the steps mention in the above thread to change the bootstack and was able to complete it without any issues, however the problem still persists and my phone is not recognizing the SIM and does not catch the cellular network.
Previously I used to use this phone with my t-mobile number and after I took a new phone haven't been using it for sometime. I want to sell this phone and was trying to ensure that it works fine and thats when I saw that the phone is not catching any cellular networks.
Please help. Let me know if you need any other details to better diagonize the problem.
hvramanan said:
Hi,
I followed the steps mention in the above thread to change the bootstack and was able to complete it without any issues, however the problem still persists and my phone is not recognizing the SIM and does not catch the cellular network.
Previously I used to use this phone with my t-mobile number and after I took a new phone haven't been using it for sometime. I want to sell this phone and was trying to ensure that it works fine and thats when I saw that the phone is not catching any cellular networks.
Please help. Let me know if you need any other details to better diagonize the problem.
Click to expand...
Click to collapse
You didn't say what model you have, maybe you flashed the wrong bootstack for your model (hardware version)? Be very careful, you can hart brick your device, and if it's a D415 it's very hard to unbrick. I'd suggest that first you make sure what model you have by removing the battery and looking in the label below, it says what model you have. Then, use LG Flash Tool to flash stock ROM (KDZ) to latest KitKat, then flash Lollipop or use OTA to update to latest version. The only requirements are that you make sure what model you have and flash the corresponding version, and the phone is still able to enter download mode.
lfom said:
You didn't say what model you have, maybe you flashed the wrong bootstack for your model (hardware version)? Be very careful, you can hart brick your device, and if it's a D415 it's very hard to unbrick. I'd suggest that first you make sure what model you have by removing the battery and looking in the label below, it says what model you have. Then, use LG Flash Tool to flash stock ROM (KDZ) to latest KitKat, then flash Lollipop or use OTA to update to latest version. The only requirements are that you make sure what model you have and flash the corresponding version, and the phone is still able to enter download mode.
Click to expand...
Click to collapse
[lfom]: thank you for responding. My phone model is LG-D415 . Actually my phone was bricked but I was able to get into download mode and then I used the L90 Hardbrick tool to flash stock ROM (KDZ) to latest kitkat like you have specified above. Then with the OTA update I was able update it to latest lollipop. Then I followed this forum below to to change the bootstack to KK 10C version as the issue specified in the below thread was similar to mine.
http://forum.xda-developers.com/lg-l90/development/rom-cyanogenmod-12-lg-l90-t3049512/page235
Image of the label inside my phone attached.
Do you think I should have used the LG flash tool to flash stock ROM. Should I repeat the steps with the LG flash tool ?
Thank you again for helping me on this.
Do you see your IMEI in the about phone page? Does it match the one in the label? Maybe when you bricked you've lost the phone's IMEI, and you can't get it back just flashing ROM...
lfom said:
Do you see your IMEI in the about phone page? Does it match the one in the label? Maybe when you bricked you've lost the phone's IMEI, and you can't get it back just flashing ROM...
Click to expand...
Click to collapse
Yes I checked and it matches. There two fields IMEI which has the number and then there is another field which says IMEI SV and it has a value of 02 in it.

loose imei, not detect sim card

Hello,
I'm french, excuse my langage...
I have 2 note 8, an N950F (single sim) and an N950FD (double sim). I specify immediately that the 2 have already worked and that I have only one sim (one being for me and the other as a gift for my wife lol)
- On the N950F, install via odin 3.14 of twrp 33.1.2, then hadesrom 12 then magisk 20.4 => everything is ok
- Purchase of the N950FD, hassle with installing twrp because I had to put my sim in it to change the time and have access to the usb options, in short, it works, then same as hades and magisk => everything is ok
I have well customized the N950FD, I made a full save (all partitions) with twrp and I said to myself I do a full install on the N950F ...
At the time I did not watch out ...
I calmly use the N950FD and then, I still hack the N950F, I install other custom roms to see, lineage 17, etc etc and all that I do it without sim, with the dex dock connected in ethernet, in me saying that when I'm done, my wife will just put her sim there ...
And then something bothers me, it's a small prohibition logo at the top left instead of the network. I tell myself that this is normal because I did not put a sim, so I take that of my N950FD and there bah it is not recognized ...
I do not panic, I tell myself that I made a false manipulation, I wipe, I reinstall hadesrom and same concern, I take another custom rom and same concern ... I redo a full install with twrp and same concern .. .
I take a stock rom (the last, then the first, always in 4 files either with the csc or with the home-csc), I flash with odin 3.14 and 3.13 and always the same problems, the rom remains blocked on the screen samsung, the first with "samsung note 8 powered by android". So I tried the last rom with 3.14 and 3.13 then the first and still the same problem, it does not start (I waited 5 minutes roughly) despite the wipes ...
Since I no longer have twrp, I reflash, it works, I tell myself that the custom was still installed and I reflash via twrp hades (I tried the stock rom file but it didn't work) and again same concern, the sim is not recognized ...
I try the flash of the hades kernel, it works but the sim is still not recognized ...
When I go to the phone * # 06 # I do not have imei, but a black screen, when I go to parameter / connection / sim card manager => black screen with the message "com-android-phone does not respond" ...
I looked a little on the net, but nothing conclusive, I specify that all my files come from XDA but that given my English I prefer to try to find an answer in French ...
I do not have a backup of the N950F it would have been too simple, I tried another sim than mine but ditto it is not recognized and before making a tablet I would like to try everything to recover it. ..
It would seem that flashing a stock rom solves the problem ... But as said above, my phone remains stuck on the samsung logo despite the wipes
I still tried other things like just flashing parts of a stock rom but I still have the same problem ...
I also tried the flash of a stock with the extra pit and the nand erase and distribution options ... and similar, no start ...
I even reinstalled twrp after a stock, save it, "mix" it with another backup I had (efs and modem from the stock and the rest of the custom) but then again, it doesn't work, such reboots well but still no network access and no recognized sim card ...
Finally, I looked at chimera tool, but no tutorial in French so no way to see how it works or if it will meet my need ... taking an exclusive samsung license on chimera does not cause me any concern IF it allows me to do other things than what I have already tried ...
I also looked at the prog to change the imei because there is nothing left, not even 0, no no, a black page just like when I go to the sim card settings, I have a black page. ..
I also flashed several custom roms from different countries but it didn't work ...
By cons I observed that I had the location for 2 sim, still inactive ...
How to put the note 8 in single sim and recover imei and then the network ???
there, I block ... if you have ideas I am taker, thank you all ...
amthium said:
Hello,
I'm french, excuse my langage...
I have 2 note 8, an N950F (single sim) and an N950FD (double sim). I specify immediately that the 2 have already worked and that I have only one sim (one being for me and the other as a gift for my wife lol)
- On the N950F, install via odin 3.14 of twrp 33.1.2, then hadesrom 12 then magisk 20.4 => everything is ok
- Purchase of the N950FD, hassle with installing twrp because I had to put my sim in it to change the time and have access to the usb options, in short, it works, then same as hades and magisk => everything is ok
I have well customized the N950FD, I made a full save (all partitions) with twrp and I said to myself I do a full install on the N950F ...
At the time I did not watch out ...
I calmly use the N950FD and then, I still hack the N950F, I install other custom roms to see, lineage 17, etc etc and all that I do it without sim, with the dex dock connected in ethernet, in me saying that when I'm done, my wife will just put her sim there ...
And then something bothers me, it's a small prohibition logo at the top left instead of the network. I tell myself that this is normal because I did not put a sim, so I take that of my N950FD and there bah it is not recognized ...
I do not panic, I tell myself that I made a false manipulation, I wipe, I reinstall hadesrom and same concern, I take another custom rom and same concern ... I redo a full install with twrp and same concern .. .
I take a stock rom (the last, then the first, always in 4 files either with the csc or with the home-csc), I flash with odin 3.14 and 3.13 and always the same problems, the rom remains blocked on the screen samsung, the first with "samsung note 8 powered by android". So I tried the last rom with 3.14 and 3.13 then the first and still the same problem, it does not start (I waited 5 minutes roughly) despite the wipes ...
Since I no longer have twrp, I reflash, it works, I tell myself that the custom was still installed and I reflash via twrp hades (I tried the stock rom file but it didn't work) and again same concern, the sim is not recognized ...
I try the flash of the hades kernel, it works but the sim is still not recognized ...
When I go to the phone * # 06 # I do not have imei, but a black screen, when I go to parameter / connection / sim card manager => black screen with the message "com-android-phone does not respond" ...
I looked a little on the net, but nothing conclusive, I specify that all my files come from XDA but that given my English I prefer to try to find an answer in French ...
I do not have a backup of the N950F it would have been too simple, I tried another sim than mine but ditto it is not recognized and before making a tablet I would like to try everything to recover it. ..
It would seem that flashing a stock rom solves the problem ... But as said above, my phone remains stuck on the samsung logo despite the wipes
I still tried other things like just flashing parts of a stock rom but I still have the same problem ...
I also tried the flash of a stock with the extra pit and the nand erase and distribution options ... and similar, no start ...
I even reinstalled twrp after a stock, save it, "mix" it with another backup I had (efs and modem from the stock and the rest of the custom) but then again, it doesn't work, such reboots well but still no network access and no recognized sim card ...
Finally, I looked at chimera tool, but no tutorial in French so no way to see how it works or if it will meet my need ... taking an exclusive samsung license on chimera does not cause me any concern IF it allows me to do other things than what I have already tried ...
I also looked at the prog to change the imei because there is nothing left, not even 0, no no, a black page just like when I go to the sim card settings, I have a black page. ..
I also flashed several custom roms from different countries but it didn't work ...
By cons I observed that I had the location for 2 sim, still inactive ...
How to put the note 8 in single sim and recover imei and then the network ???
there, I block ... if you have ideas I am taker, thank you all ...
Click to expand...
Click to collapse
If you didn't take a backup of your /efs folder which is where all of the phones important information is stored such as your IMEI then you are screwed because you can't flash any other phones EFS FOLDER.. However if you have a backup efs folder, restore it.
the concern is that I do not have a backup of the efs file ...
is it possible to put an efs file of another note 8 n950f and where to find this file on the net?
amthium said:
the concern is that I do not have a backup of the efs file ...
is it possible to put an efs file of another note 8 n950f and where to find this file on the net?
Click to expand...
Click to collapse
MrMike has already answered this, you can't share or use any other EFS.
The fact you can flash a custom rom and it will boot tells me you don't have a hardware issue, try flashing stock again as this can sometimes fix the EFS file, it has done for me in the past and a few others users. Although I can't tell you why you get stuck after flashing stock, this is the best way for you to hopefully resolve your issue as you don't have a EFS backup.
Except by flashing a stock, is there a way to restore the n950f to factory condition?
because with odin, if I flash the last stock, it does not start even if I make the wipes and if I try an old stock, odin blocks ...
can the chimera program allow me to find an original n950f?
amthium said:
Except by flashing a stock, is there a way to restore the n950f to factory condition?
because with odin, if I flash the last stock, it does not start even if I make the wipes and if I try an old stock, odin blocks ...
can the chimera program allow me to find an original n950f?
Click to expand...
Click to collapse
Not that I am aware of, I am only aware of restoring by flashing stock with Odin or by using Samsung smartswitch.
You can't flash older filmware than what is already on the phone, that is why Odin is blocking that, but when you flash the latest filmware does Odin give you the green pass?
I am not familiar with the Chimera program so can't speak on that.
Yes with odin I have the green pass, but then the note 8 does not start, it remains blocked on the logo, even if I do the wipe ...
I even tried to save right after with twrp and recover the efs but it does not work ...
If I find a broken Note 8 can I recover the efs file by saving it and then putting it on my own?
hainguyenthao said:
Device will not boot while there is an error in efs partition so u need to fix it first i have same device and i can help you to boot it
Click to expand...
Click to collapse
Thanks for your help, how to start it in stock rom?
I specify that it starts in custom rom ...
the first photo is before the installation of the stock rom with odin, the second is at the end of the installation (odin ok, pass in green), the third is after the restart which has not worked (blocking on samsung note 8)
hainguyenthao said:
Sorry error when loading images 404 Not Found upload it again or send it to my email
Click to expand...
Click to collapse
Could you please explain to us all in here how you're going to fix his /efs folder when he never made a backup of it.. Where are you planning on getting him an /efs folder that held all of his phone's information when he accidentally deleted it?
hainguyenthao said:
By root device and download Root Explorer, browse to the efs folder the delete everything EXCEPT the 'FactoryApp' and 'prov_data' folders it should restore IMEI
Click to expand...
Click to collapse
I gave this a shot but it didn't work for me.

Categories

Resources