Related
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
dew1989 said:
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
Click to expand...
Click to collapse
It seems that you bricked you phone mate. I think that you installed MrClean rom in a G4 phone so you irrimediably f*cked up the bootloader (IPL and SPL). Many users have reported that their phones were able to boot (and behaved normally) immediatly after the flashing but were dead after they turned them off for the first time, this is what happened to you.
Only thing you can try is going to bootloader mode (but i think it won't work since you messed the bootloader) and then flash a new rom. To do this, press and keep pressed both the keys on the right side and then insert a pin in the reset hole briefly. If the phone goes to the tri-colors screen then you're safe, if not continue reading.
If your warranty perior is not yet over then you can have a new phone for free (DON'T tell them that you flashed an experimental rom!!! Tell only that it went off suddenly or that you were installing an official rom!).
Service centre can repair your device (i suppose they've some method to reflash the bootloader) but i don't know how much they'll ask you.
Try asking other users on this forum. Sorry!
bye
...did you ry to recharge it with the ----ORIGINAL 1A CHARGER----? looks stupid, but i resuscitated mine just before throwing it in the bin. if it works, i will explain you the rest....
yup, I tried charging it with the home charger and still nothing. My battery reads at 3v and it's supposed to be 3.8 so it's not out of juice, but maybe it's just dead?
...you can try with just a normal 9 VDC battery, in order to boost up the voltage, to connect it for a few seconds to the ppc battery till you reach the 3.8 VDC and see if it's working...
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
dew1989 said:
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
Click to expand...
Click to collapse
This is waht you need:
http://www.thetravelinsider.info/phones/cellphonerecharger.htm
This charger is somehow wired weird... it charges the battery AND feeds juice to the phone at the same time (believe it or not, regular chargers and USB cables do not engage until the OS is loaded), allowing you to turn the phone on and in a few minutes plug it into the regular charger to continue charging. Just make sure you get the RAZR tip.
It has saved my ass more than once.
I fixed it , What I did was zap the battery with a 9v battery in 3 sec intervals, I did this about 5 times, then I pluged my phone into the charger and turned it on, the 9v gave it enough juice to boot up and the usb took over from there. So to everyone out there who is having this same problem, try this but don't over zap, check your battery with a multimeter.
im having the same problem----my MDA went dead last night because i forgot to charge the battery and then i went to plug it in the charger but the phone doesnt turn on no more...the light doesnt turn on like if it would be charging and i left it overnight and it still doesnt work..... do yall think that its the battery or is the phone just messed up and cant use it nomore????
Last time I had my battery completely drained, it wouldn't charge from laptop via USB. I read something about how the device's "smart-charging" function itself needs a bit of power to start-up...
but anyways, I couldn't charge the battery through the phone (software charging) - what I had to do was to take a USB cable, cut out one end, identify the +/- (red/black) wires, and charge them directly to the battery's two poles (metal plates). It took about 10-20 seconds of charging until I had enough power in the battery to place it back in the phone, start WM5 and charge it thru the phone.
It would have been much easier if you have a battery charger.
I had my phone connected to the computer through the usb cable, and I just left it connected for a week and it was completely dead and could not be turned on. I don't know how it drained the battery (probally by leaving the wifi on, but the computer was in use all the time). Anyway, thanks to this thread, I used the ac charger and it turned on.
Keywords: t-mobile tmobile mda phone won't don't turn on
phone down
thanks for infos
I'm going to give this a go; a Crossbow ROM flash went horribly wrong last night and in my attempts to repair it (I also must have flashed at least 9 times) the phone went dead. It won't charge either, but battery voltage is 3.7 volts, and I'm sat here wishing it was 3
Will get back to you all!
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Suggestion
CrArc said:
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Click to expand...
Click to collapse
My phone has a hardware problem with the on / off button (doesn´t work at all), at the beggining I thought it was a software problem and I tried all sort of tricks, then I gave up and recognized that was a hardware issue and I found 2 ways to turn the phone on 1) When is totally off (This happens when I have to remove the battery to change SIM card) I connect to the USB cable to my PC or to the car or wall charger and I make a soft reset. 2) When I see the phone signal led blinking I remove the memory card and wakes the phone up (not a good idea since I know that the card is going to get damaged sooner or later).
I just got a G3 wizard from a friend a couple days ago. On Thursday I upgraded it to XDA Mobile 6 and left it on the 2.25.11 (I think) T-Mobile Radio that the T-Mobile 2.26 firmware flash put on it. I used it all day on Friday and then I held the power button and shut the phone completely off for 25 hours, but left it plugged in to a usb to 110V AC adapter that came with my Dell Axim X50V. On Saturday night I went to turn it on and it would not come on no matter what I tried. I found this thread and checked the voltage on the battery directly with a multimeter, 3.13V. I cut the head off a usb cable and then held the black and red wires to the positive and negative terminals on the battery for 2 minutes with the head plugged into a front USB port on my PC. The multimeter then read 3.7V. I put it back into the MDA and it turned on, booted and informed me that the battery was completely drained. I plugged it into the USB to AC charger and it read 10% battery on BatteryStatus. I have left it to charge and it is currently at 60%.
I guess the lesson here is to not totally shut the phone off and let it sit, or the battery won't charge, even plugged into my charger. I guess the OS needs to be running in suspend mode for the charging circuit to run. I know I won't turn it all the way off ever again unless I have my little plug thing and my laptop with me.
(old) Nokia phones have a state called "Acting dead" (from service manuals) which takes place when phone is turned off and battery inserted. It means that the energy is flowing around the board so that the responsible hardware keeps waiting for a 'HIGH' signal ordering to turn ON the phone.
When batteries go bellow the 2.x volts they stop being charged by the phones. This is why i protect the battery terminals with tape when the phone is stored for some time and the reason why a lot of people thinks the phones are broken when not used for months. I usually use the 'freezer trick' where i leave the batteries inside the freezer all night and charge them next day.
just 2 cents...
My Wizard XDA got discharged over the weekend and wouldn't start up - after 12 hours on USB it still wouldn't start.
The charge tips saved my bacon - I modified a USB cable as per the instructions above, and used it to charge up the XDA battery - it only needed five seconds and the phone now boots!
Thanks All, great information!
My 2 cents...
If you're going to try the same, connect red usb to the +ve terminal of your battery and black USB to the -ve terminal of the battery. I'd suggest having a voltmeter to hand to check battery and supply voltage.
Disclaimer - the ablve worked for me, but I'm not responsible for anyone damaging themselves, their PC,their phone or anything else by using the above info!
BUMP! thought my phone was dead, hacked a USB cable and i'm back in business!!!!
TYTN II won't turn on
i left it plugged in all day and when i tried to turn it on it didn't respond. i have a second battery that was fully charged and that didn't work either. i tried a hard reset with it unplugged and with it plugged into the charger. nothing works. i'm on the standard at&t rom with lots of programs. i got it unlocked so i can't go to at&t.
I posted this question before, but no one answered. But this problem drives me crazy!
My Kaiser turned off when the battery was running out.
When I connect wall power to charge it, the orange LED indicates it was charging, but just few seconds later it automatically boot, and the orange LED was off.
The problem is, it can't boot into OS due to low battery(it only shows "Smart Mobility", but can't even enter bootloader mode) And only if it boots into OS successfully, it can be charged.
Anyone met this problem on any other devices before?
How can I stop auto boot when charging?
What can I do?
That must be something specific to the rom on yours... mine does not automatically boot when when power is applied (assuming it is off, not just in sleep mode), and it charges fine when powered off.
dscline said:
That must be something specific to the rom on yours... mine does not automatically boot when when power is applied (assuming it is off, not just in sleep mode), and it charges fine when powered off.
Click to expand...
Click to collapse
Thanks
I use the ROM from this forum
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
What is yours?
I'm just using the stock AT&T Tilt rom.
Here's the fix!
Yes, I've had the same problem a few times on my Vario (Wizard). Very annoying.
Here's what to do:
- Take a mini-usb cable (the one you use for sync and charging from a PC) and cut off the mini-USB connector
- Strip the wires
- Take the battery out of your TyTN
- Carefully connect the ground wire (black) with the ground connector (-) on the battery. Fix it with clear tape.
- Now do the same with the (+) (red wire).
- Attach the USB cable to a running PC and let the battery charge for about an hour. After that, put it back in your phone, you'll be able to boot it up and charge it the regular way.
Yes, it costs you a cable, but it solves the problem.
dscline said:
That must be something specific to the rom on yours... mine does not automatically boot when when power is applied (assuming it is off, not just in sleep mode), and it charges fine when powered off.
Click to expand...
Click to collapse
I think you misunderstood. The problem is that the phone only charges when the OS has loaded completely. So if you really run your battery out completely and there is not enough power in your battery to boot up the phone (read: it turns off again before the boot has completed) you won't be able to charge it the regular way. SOMETIMES a heavier charger (2A) does seem to be able to charge the battery even with the OS shut down, but most of the times it won't work anymore... see below for fix.
SteRo said:
I think you misunderstood. The problem is that the phone only charges when the OS has loaded completely.
Click to expand...
Click to collapse
That's not how I read the original post:
When I connect wall power to charge it, the orange LED indicates it was charging, but just few seconds later it automatically boot, and the orange LED was off.
Click to expand...
Click to collapse
Based on this, it sounds like it is starting to charge without the phone booted (orange LED on), but for some reason it then automatically boots up, then crashes because there's not enough power(??)
But if the problem IS that the phone only charges when the OS has loaded, that is also not how my phone operates. In fact, that even goes against the manual, which tells you to plug the phone in (without turning on the phone) and let it charge fully for the initial charge before turning on the phone and allowing it to boot.
Sorry if I misunderstand, but neither way is how my phone operates... it can charge without the OS loaded, and the phone does not automatically boot once power is applied.
Not sure I fully understand what's going on here but, I am wondering if the power on/off button is stuck in (i.e the micro-switch is clicked in and not releasing). I cannot think of any other reason the device would turn on when connecting the charger if the device is powered completely off. ( Except perhaps shorted connections in the Usb port)
Mike
To SteRo:
Thx a lot for the solution, I tried, but still doesn't work.(I charge it more than 2 hours, and still can't boot into OS)
To mikechannon:
yes, it happened. :-( the power on/off button is NOT stucked. And the device is powered off completely.
To All:
Thx for your reply. What I mean is almost what dscline said:
It starts to charge without the phone booted (orange LED on), but for some reason it then automatically boots up(around 15 sec after I plugin power), meanwhile orange LED is off. But it can't load into OS, just re-boot again and again because there's no enough battery. That makes it's impossible to charge, 'coz it's only charged when the OS has loaded completely.
Anyway, I called customer service to ask them replace the battery. I may try to use different ROM and see what will happen. I'll post the result here.
It's also possible that it has nothing to do with the battery or charging at all. I just checked mine, and the charging indicator is lit with the unit off, but it does go out for a bit during the boot processes, then comes back on again. So what you're seeing with the charging light is normal. It may simply be that there's something corrupted, or some other failure with the device, that is causing it to not boot properly, and get stuck in a reboot loop. If so, it will probably do the same thing with a completely charged battery. You may have just been assuming that it was related to a low charge.
That's what I'm worry about,, Coz I can't boot it by SteRo's solution.
okay... they say trouble comes in three's...
Yesterday I flew to Asia, 20-hours with a full charge. No suprises during the trip. Checked email from Narita during the layover, no prob. But after I arrived in Taipei I received the low battery warning. Plugged in my usb-to-usb (notebook to kaiser) cable and "no charge light"!
This morning I plugged it into a ac battery charger and waited for >10 minutes, still no charge light.
Now, at the risk of a battery, I'm attempting to charge the battery removed from the kaiser using the previous mentioned method. In an hour I'll test it.
This afternoon I'll pick up a new battery charger and spare battery.
In 14-months with my trusty TyTN (cht9000) I never once had a problem like this... I'm a little bummed right now...
[update]
okay -- battery is okay and can be charged externally (using the two wire method or an external battery charger). BUT... the device still won't take a charge using either a direct AC adapter or a USB cord. This was also retested after performing a hard-reset. Not a good sign folks.
The charger works (connected to a Trinity), so it's not the problem. They battery works (charged to 45% after 45-minutes connected to an external battery charger). The HTC OS after a clean hard-reset used to work but now doesn't, so it's unlikely it's software related.
I've made no other modifications to the bootloader or SSPL... everything is original stock. Wish I had my TyTN with me right about now...
Sounds like something I had on my previous TyTN:
The power connector was a bit flaky on my charger at home. So when I'd hookup the powerlead it would charge to 10 secs or so and then no longer charge. I had to put some pressure on the connector to have it continue to charge. So I put a ballpen on the powerlead, just under the phone, when charging.
It's a long shot - hope of use. When you've connected the phone to power, and the orange light goes off, try wiggeling the connector a bit - see if that helps.
Hope of use.
Re
OK,
I've got excactly the same problems... I dont want to make you illusions, but you cant solve it and you need to send it back for repair. Your usb connecter on your tytn is broken...
first i will tell my story...
My tytn did excactly the same, shows the led, powers on automatically (normally it don't do that, so it;s not a rom issue) and then powered down in the smart mobility screen. I tried 4 chargers, and 2 battery's. with a full battery it will power on and load windows, but unable to charge. with the empty battery it will power down in the smart mobility screen. soft reset, hard reset, it won't work.
You can check if it's the same problem, by attaching it to your usb on your computer and call up the bootscreen by pressing the camera button and stick your stylus in the soft reset hole. If it comes up with serial instead of usb, then your device usb connector is broken.
BUT, you can charge your battery in a very strange way i figured out. since i am on a buisness trip i need my phone and don't send it back!!!!!
ok, this is what you have to do, plug in the powercable, call the hard reset screen BUT DON'T APPLY!!!! you will notice it will not power down, so just leave it on this screen for a night with the cable connected. you don't see the charging light, but actually it is charging. for me this temporarely solution works fine... but when i'm back in about seven weeks i send it in for repair.
Hope this will help you!
Swiftgs:
Many thanks for your insight -- you are correct, in bootloader mode the Serial shows instead of USB. I just purchased a spare battery (1100mAh, made in Taiwan) and battery charger for US$17. It'll get me through my business trip, but this is disappointing. As I mentioned in my earlier post, I used a TyTN for 14-months (July 2006 to Sept 2007) as my primary phone, recharging it daily via the USB connector and on a desk charger in my office. I can only conclude that if the USB is physically damaged (not evident visually), then it is not as robust as the USB port used in the original TyTN. The strangest part of all is it worked perfectly until the battery level fell below 10%...
FWIW: I purchased the phone through R&D Marketing. Ron Webber quickly responded to my note and gave me a contact at HTC America. I'll follow-up
after I return and report my experience.
Cheers
well, thanks for all of your replies/infomation.
I tried evey possible methods mentioned above, unfortunatelly none of them works :-(
and the most depressed thing is I filnally get a new battery, but it still doesn't work!
So I sent it back to repair, cross figure...
It works
I would like to thanx 2 SteRo for his advice. I am using Qtek 9000 and had the same problem. Battery was empty, and I tried many times to turn on my PPC, but without success. All the time when red light appeared after 10-15 sec display become black and tried to restart from boot again, and it's happened many times. Finally I thought that I just can trow my Qtek, but seeing your recommendation decided to try. I took USB cable cut it and strap the wires. Connecting red on (+) and black on (-) after 1 hour charging I was able to start my PPC, to recharge battery by 100% and it is working now OK. I must check duration of the battery tomorrow, because reason why I discharged battery was automatic turn off of my PPC when it was on around 45-50% battery capacity. Tomorrow I will check how it's working when I recharge battery again.
Dear SteRo you are the king.
hi, new member here.
bought my tilt on 10/4/07. has been flawless since that time.
used the nav quite a bit during a road trip, used a cig lighter usb charger.
got home and my battery was at roughly 40%.
put it on the charger at night went to sleep. in morning disconnected it at 8 am. shortly after i arrived at work i got the critical battery low chime. checked and it had like 7% battery life.
figured i didnt plug it in right, or it got knocked loose some how and didnt get charged.
put it in flight mode to minimize battery usage. left work at 2 30 pm (4% battery life) and put it on the car charger. got home and put it on the HTC supplied wall charger. light turned amber, so i assumed it was charging.
checked an hour later and turned phone on, it said 0%, and immediately died. left it on the charger for a few hours and the light was still amber, turned it back on and again 0% and phone immediately died and did a soft reset on its own. i turned the phone off and left it on the ac charger, took out the sim card and put it in an old blackberry to use while the battery was charging.
its been on the ac wall charger for the last several hours, i checked and the phone is totally dead, cannot turn it on, and the LED at the top is now RED.
what is the problem here? why wont this thing charge?
thanks in advance, i have alot of critical info on this device and any help would be greatly appreciated.
i cannot hard reset because i cannot turn the flippign thing on....
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
I'd try a different charger first. If that makes no difference then a different battery. If that still does not make any difference then time to exchange it.
Lidberg said:
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
Click to expand...
Click to collapse
connected to either the computer or the wall charger, the LED thats normally amber when charging, and green when charged, remains red.
I had something very similar happen to my wizard.
And as weird as it sounds, the only fix was to charge the battery in a friends wizard on his charger. I'd check the battery if possible.
Could be the battery. Know any place or anyone that will let you try a charged battery? If not, you might have to go in to an AT&T store.
i think i got it working. did some reading/browsing...
took a usb wire and cut the mini usb head off. dissected it and found the the red and black charging wires. took out the battery and held the leads to teh battery while the other end was plugged into a USB/AC adapter wall charger from a old blackberry. after manually charging the battery for several minutes, i put the battery back in the phone and the phone started up. now it seems to be charging off the wall charger and the led is now amber from red.
thanks for all your help/suggestions.
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
tiltyoself said:
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
Click to expand...
Click to collapse
Repeat this proceedure but this time do not turn the phone on, just plug it in to the wall charger once you have zapped the battery again.
Turning your phone on probably just caused the already recovering battery to die whiles it is trying to take on a charge.
It is mentioned quite a lot on the boards that Li-Ion Batteries do not like being over disscharged and there is usually a little protection circuit in the battery to provent complete disscharging although this circuit may be on board the phone. Completely disscharging a Li-Ion cell will kill it stone dead and it will need replacing.
When you took the battery out and so called jump started it with your flying leads, this possibly reset the little protection circuit in the battery so it can now take on a charge. I feel that once you turned on the phone, this was to much for the already depleted cell to take and possibly re-tripped its inbuilt circuit.
If you do manage to recover you cell, in future it is good practice not to let the battery go below about 25%. Li-ion cells are generally happy being top off regularly.
I hope this helps buddy
Do let us know!
Cheers
C.
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
That Sucks! I hope they'll give you a new battery.
tiltyoself said:
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
Click to expand...
Click to collapse
I had exactly the same problem with my battery. It came on though after a day. Although the battery life after this happened went down to 10hrs max on standby. I sent the phone back and got a new one and now all is fine.
This is a problem that affects almost all makes of phone. There are three (main) causes of the problem:
1.
The battery charge drops too low to allow the charging circuit to recognise a battery is even in place (red no charge light stays lit)
possible solution:
http://forum.xda-developers.com/show...22&postcount=6
(in the end very similar in the end to the USB wire used in post above)
2.
A faulty battery (but if you can charge it using a cut usb cable or using a couple of AA batteries this may not be a faulty battery.
3.
A faulty charger OR a charger not delivering 5v at 1000mA as the OEM one does. Many chargers that are used for other phones or generic chargers only deliver 500mA. This is not enough when your battery drops very low. (these chargers are OK for occasional use but I do not advise using them regularly particularly if the no-charge syndrome has shown itself)
4.
A faulty USB connection on the phone. I have now seen a couple of reports where the fine wire connections in the phones USB port have become bent out of place.
Number 4 above is at least possible for the OP as it seems the battery will charge using a cut USB cable but not when either the PC USB cable or mains charger is connected. A USB port on the phone with a a bent internal contact would explain what's happening.
A previous poster was able with a needle or similar to bend the contact back into place.
Mike
i had the same problem with my phone.
put it in the charger overnight and woke up in the morning and couldnt turn on the phone with blinking red light. I don't know if my battery was over-drained though. I went to AT&T and was playing around with their charger and new battery and somehow the so-called dead battery started working again. They changed the SIM card on my phone there and then i haven't been able to use the phone since. I've changed the network to GSM instead of Auto setting under Phone Options which allows us to make calls; but now I can't connect to 3G network.
Charging thru mini usb
My phone started to exhibit similar problems...plugged in but no charging of the battery. I finally realized that my mini usb connection on the phone has been compromised (bent, distorted=not functioning properly) Now I have to prop the mini usb connection up at a slight angle to engage the charge. I think the plastic/metallic connector on the phone is somewhat fragile ...I had similar issues with my hermes.
called customer support.
they are sending me a new phone and battery.
how do i know its not a refurbished one? any clues?
before u send out your defect phone, have u check if your phone's mini-USB connector has bent or misaligned pins?
yeah all the connectors visually are fine.
Hello everyone.
Just received my HTC TyTN II.
I just registered my device at the HTC web site, but after replacing the battery and closing the cover, the device refuses to power on.
Also, charging the battery gives a RED led, instead of the usual ORANGE or GREEN.
Anything I can do, or is it broken?
Thanks,
Loki
i had a similar issue, you need to charge your phone up. Plug it into an external power supply, not the computer, and charge it. WHen it displays a red LED, it means the battery is in a critical low. Charge it full asap
SImilar issue but call cingular and they send me replacement phone
Loki1973 said:
Hello everyone.
Just received my HTC TyTN II.
I just registered my device at the HTC web site, but after replacing the battery and closing the cover, the device refuses to power on.
Also, charging the battery gives a RED led, instead of the usual ORANGE or GREEN.
...
Loki
Click to expand...
Click to collapse
SImilar issue but call cingular and they send me replacement phone.
ekw said:
i had a similar issue, you need to charge your phone up. Plug it into an external power supply, not the computer, and charge it. WHen it displays a red LED, it means the battery is in a critical low. Charge it full asap
Click to expand...
Click to collapse
I swapped batteries from another TyTN II and same issues. My battery in the other one, no problems.
I think it is gone. I'll contact the supplier for further instructions.
Thanks anyway.
Loki.
This happened to me as well and a few other posts on this board. It appears to be a pretty high failure rate.
I have called HTC Europe.
It is a quite common problem and the device will be considered a DOA since it is only 3 days old, and will be replaced by a service center in Belgium. Back to using my Wizard for a couple of days more.
Thanks for the info!
Loki.
ekw said:
i had a similar issue, you need to charge your phone up. Plug it into an external power supply, not the computer, and charge it. WHen it displays a red LED, it means the battery is in a critical low. Charge it full asap
Click to expand...
Click to collapse
When this is the case the red LED is flashing meaning battery low, if it's on all the time it's a dead phone as mine went yesterday and HTC are replacing it.
I have a familiar problem we've all read about but my instance seems to be a bit different than anything i've found when searching the forums. Heres the Details.
I have a Tilt, I'm running Dutty's WM6.1. I've been running it for weeks and all is great. recently bought a usb car adapter. plugged it in and the phone lit the red light of doom and shut down. i soft reset...same problem. so I left it alone. Now my TILT turns on fine, operates fine. boots in a timely fashion but will not recognize any USB cord i've plugged in. I've tried many. However it WILL charge when the power is turned off. the red light is lit while charging but it charges.
and in case it helps anyone...the bootloader does say SERIAL and no usb.
I've seen lots of different instances of this issue on the forum search but they all were a little different from my situation or an answer was never given in the thread. Thank you to any one who knows the secret to this or has a solution that works.
Seems you fryed some part of your USB port. You should send it in to AT&T if you're under warrenty. If not, best thing is to replace it by solderng a new USB port.
Kraize
Since you can still turn it on and all seems relatively normal why not back up your data and try a Hard Reset ?
You may not have bricked it...may I ask which USB car charger you bought so I can avoid it ?
I doubt the physical USB jack is damaged, anythings possible but it's more likely worse than that IF it is not software/rom related.
Hope you solve it cheaply !
are you trying to charge it with the one that came with the kaiser?