need to upgrade radio to1.06.02 - MDA III, XDA III, PDA2k, 9090 Software Upgrading

hi i have qtek 9090 rom 1.22.00 WWE with radio 1.06.00 and would like to upgrade the radio only to 1.06.02
how can i do this???
tahnks

yo.. does any one know if the country id problem on any of the roms with radio version xxxx.02 is solved???
thanks

Wot country error? I just extracted 1.06.02 radio from belgian rom, ran:
xda3nbftool -x radio_.nbf radio_.nba 0x20040523
xda3nbftool -so T-MOB101 -sl GER radio_.nba
xda3nbftool -x radio_.nba radio_.nbf 0x20040523
del *.nba
I only left radio_.nbf of the 3 nbf files. Ran the update utility with activesync disabled, and that was it. -> I have a german t-mobile mda iii unlocked, with the official t-mobile blackberry upgrade <-
This was only an advice, i don't take any responsibility if ur update goes wrong! :roll:

hi
thanks you totally rule!
now i have the upgraded radio version...

hum !!
So me reflashing os and extened rom with the extracted 1.06.02 was a waste of time even though it worked.
I am reading that I can just run the fix and upgrade with radio only,
that it takes less than 1 3rd of the time?
Does the cold boot not just wipe out all of the applications and start the exteneded rom autoconfig!

Can somebody upload the TMobile Patched radio_.nbf 1.06.02
I've downloaded and tried to patch the radio rom as above from qtek.nu but it didn't work ( apparently the new files have a different allogorithm to encode ). Can someone upload or pm me the German Tmobile patched radio 1.06.02?

http://forum.xda-developers.com/viewtopic.php?p=84107#84107
take the ftp link

Related

bootloader screen after tried zu upgrade

Hello,
i have a little problem, I tried to upgrade my VPA III (BlueAngle from Vodafone) to a version with Blackberry support. I do that with the rom_upgrade_mda3.exe from t-mobile. After this upgrade failed I only see the bootloader (serial/usb v2.07). Now I not posible to get an working OS on the PDA.
What I tried to now.
* Dump an image to a SD card. But I get the error section=3, not allowed, update
* run the rom_upgrade_mda3.exe again, I get the error 120 contry ID error
* run xda3nbftool to change the operator ID, but I get the same error (120) again only th last digits change. (45-45-xxx-xxx-...).
Now my question have somebody a working XXXX.nb1 file or know somebody which -so an -sl flag is to use in xda3nbftool for vodafone in germany .
Please help me, thank's
Best regards.
IHWTL
bootloader screen after upgrade
I have the same problem. Please Help.
Phone specs:
Qtek9090
No operator
DANGA001 (at the beginning)
WWE
Me too!!!! HELP!
How it worked for me
I had the same problem...
http://www.ppc-welt.info/community/showpost.php?p=490144

I've read the Getting Started section but im still stuck!!

Hi,
I just bought a year old T-Mobile MDA111 from Germany and need to change the operating system to WWE. I downloaded the Getdevicedata.exe file but cant seem to get it to work (probably since i dont understand german!). I tried copying it to ( \Windows\Start Menu\Programs\XDA-Tools\ ) but couldnt find \XDA-tools. Even when i saved it in programs and ran it from there it did not work.
I managed to figure out the following though:
Model: PH20B
Language: GER
Oerator code: T-MOB 101
ROM: 1.06.01
Ext. ROM: 1.06.115
Radio: 1.00.00
Could anyone help me!!
Re: I've read the Getting Started section but im still stuck
xummy111 said:
Hi,
I just bought a year old T-Mobile MDA111 from Germany and need to change the operating system to WWE. I downloaded the Getdevicedata.exe file but cant seem to get it to work (probably since i dont understand german!). I tried copying it to ( \Windows\Start Menu\Programs\XDA-Tools\ ) but couldnt find \XDA-tools. Even when i saved it in programs and ran it from there it did not work.
I managed to figure out the following though:
Model: PH20B
Language: GER
Oerator code: T-MOB 101
ROM: 1.06.01
Ext. ROM: 1.06.115
Radio: 1.00.00
Could anyone help me!!
Click to expand...
Click to collapse
I managed to find the DeviceData.txt which gave me the following - PH20B O B GER R T-MOB101 1.06.01 01 1.06.115 1.00.00 00.00
I have now downloaded the following : BA_TMUK_14200_112_11300_Ship
I also managed to use editfix.bat to edit the correct details and i dont think i saw any errors.
BUT.... once i tried running BAUpgrade, i got this error - Radio Image file checksum error
What now??
The 1.42 rom that you downloaded is a type II rom thus the editfixbat will not work (you will get an ERROR in the dos window).
The best is just follow the upgrage instructions of the 1.42 rom as per wiki, it will work and you will end up with a WWE device that is branded by that operator.
Then all you need to do is play in wiki the extended rom kitchen.
Thanks,
Since that post, i tried updating to the current German T-Mobile ROM and this was successful.
Do you think i would be able to manage just the same if i download the Dutch or UK version and work with those? I am currently downloading the following:
ftp://xda:[email protected]_11300_SHIP/BA_TMNL_14200_115_11300_Ship.exe
Dear MDA111user, i hate bothering people but you seem to be the one who can really help me!
I followed the upgrade instructions as per wiki as you told me but i am still getting errors. Do you know which would be the best ROM to use since i need to change language from GER to WWE?
For your info the current status of my MDA111 is as follows:
Oper : T-Mob 101
sold as: MDA111
Shipped Lang: GER
Hardware Keyboard: QWERTZ
SIM was: Unlocked
Shipped Version:
CE = 1.06.01
ExtRom= 1.06.115
Radio= 1.00.00
Shipped GetDeviceData.exe/DeviceData.txt info
PH20B O B GER R T-MOB101 1.06.01 01 1.06.115 1.00.00 00.00
Last know Offical update:
1.42.01 1.42.116 1.13.00
Offical web downlaod site:
T-mobile.de
Last know upgrade that worked
As above
Upgraded on:
19.01.2006
There is no BEST rom, some of us like the 1.31 others 1.40 and others the 1.42. Can't tell you what to do only what I have done, and I have had them all.
Can't help you on the errors unless you tell me what they are. The wiki update page is tried and tested and works, well did for me and many others.
The getting started was written based on Type I roms, Now we have type II and we bypass the county code error with the MA_noID....exe file.
So if you want more help you need to tell us what you have done and what went wrong.

downgrade from wm5

hi can any body help me to flash my german blueangel back to his original firmware. but the problem is to get the device into the bootloarder. i can´t press the power button to get the device into the bootloader . have anybody a tool to get dhe device into the bootloader per software ???
sorry formy very bad english
thx for help
greez
As far as i know there is no software that can do that button emulation. I suggest you go to the nearest service center to replace your button
---
i have this read in the wiki here
BaUpgradeUt.exe = The Upgrade Program
EnterBL.exe = Puts the device into the Bootloader Program
GetDeviceData.exe = If run on the device it will generate \windows\DeviceData.txt
HTCRUU.conf =Config file used by BaUpgradeUt.exe
HTCRUU.dll = used by BaUpgradeUt.exe (I think)
ms_.nbf = Extended ROM
nk.nbf = OS ROM
radio_.nbf = Radio ROM
but why ist did not work ???
please help me
greez Capone

How to relock the CID

Hello
A quick question. I've searched around for the answer but haven't found it yet - could someone please enlighten me?
I upgraded then downgraded my ROM but I need to know how to relock the CID.
Does this happen automatically when you upgrade? Is there a way of knowing if it's locked?
The lokiwiz application only has the option to unlock.
Any comments greatly appreciated.
Thanks!
This is possible,
edit lokiwiz.bat
line:
Utils\wizardunlock.exe lock_backup.bin -c 11111111 -w cidunlocked.bin
where you enter your ORIGINAL CID in stead of 1111111
as an example:
Utils\wizardunlock.exe lock_backup.bin -c TMO_0901 -w cidunlocked.bin
This will relock your CID to TMO_901 (I believe it is T-mobile WWE)
List of CID's
I extracted this list of CID's from the nb2nbf tool:
ORG_0401 ENG
ORG_0402 FRA
ORG_0403 SVE
ORG_0404 DAN
ORG_0405 NLD
ORG_0406 Belgium
ORG_0407 Thailand
ORG_0408 SKY
ORG_0409 ROM
ORG_0410 PLK
ORG_1002 FRA
TMO_0901 WWE
O2__0801 GER
VODA0501 GER
VODA0502 ITA
VODA0503 ENG
DNG_0501 Nordic
DNG_0502 European
DNG_0503 RUS
BPT_0501 Nordic
BPT_0502 European
BPT_0503 RUS
DNG_0601 Nordic
DNG_0602 Euronpean
DNG_0603 RUS
BPT_0601 Nordic
BPT_0602 European
BPT_0603 RUS
CDL_0501 WWE
CDL_0601 WWE
O2A_0501 WWE
O2A_0601 WWE
DPT_0601 CHT
DPC_1101 CHS
CWS_0901 WWE
I don't know if these CID's are correct!!
They are probably only for Typhoon NOT for wizard
Hi
Thanks!
How do I find the code for imate? The ROM I am reverting to is:
K-JAM_WWE_1010903_106_10110_ship.exe
Is one of those .bin files an input file I need to have as well?
hazymat said:
Hi
Thanks!
How do I find the code for imate? The ROM I am reverting to is:
K-JAM_WWE_1010903_106_10110_ship.exe
Is one of those .bin files an input file I need to have as well?
Click to expand...
Click to collapse
You should be able to read the operator ID with TyphoonNbfTool_04.exe.
But you'll have to extract the nk.nbf file from the K-JAM_WWE_1010903_106_10110_ship.exe.
Looks like CID's from wizard are a tat different:
I got WIZORGE5 for Orange NLD..
Typhoon NBF Tools report the operator for the nbf file (in K-JAM_WWE_1010903_106_10110_ship.exe) is:
WIZCDL01
I'm basically trying to lock the CID back up so the PDA is exactly as it was when I bought it (warranty repair needed).
I bought the phone new from Expansys, not attached to any network, so am I right in thinking that that carrier is imate? (It's branded imate k-jam as opposed to qtek or anything else).
Also, when I come to relock, what bin files should I use?
indeed you should use the imate kjame nk.nbf file.
But you'll have to downgrade first to 1.01 (see the cid-unlock thread) the relock if both ipl and spl are the same (1.01).
after relock you can install the original rom.
I think the original ROM uses IPL 1.01 and SPL 1.06. (I already downgraded to the original ROM.)
This is the version I want to lock, because then I can send it back to repair. (I sent it back before and they refused to look at it because it was the wrong version, that is why I have to be very careful I understand exactly how to send it back as I bought it)
So, ipl is 1.01 and spl is 1.06. (OS version is 1.1.9.3)
Am I okay to lock the CID if the IPL and SPL are different?
hazymat said:
I think the original ROM uses IPL 1.01 and SPL 1.06. (I already downgraded to the original ROM.)
This is the version I want to lock, because then I can send it back to repair. (I sent it back before and they refused to look at it because it was the wrong version, that is why I have to be very careful I understand exactly how to send it back as I bought it)
So, ipl is 1.01 and spl is 1.06. (OS version is 1.1.9.3)
Am I okay to lock the CID if the IPL and SPL are different?
Click to expand...
Click to collapse
yups, if that was the original state, it is okay.

problem with CID lock

i've got a problem with my BA when i try to flash my ROM, everytime there is a problem with : COUNTRY ID ERROR which is CID, I have tried to unlock it with lookwiz which i have found here, but it didn't help me please help me how to upgrade my Qtek to wm5 or wm6... Thanks
So, here are some info about my ROM :
Model = PH20B
ROM-version = 1.22.01 GER (wrrrr, i don't like german, cuz' i don't know it)
RADIO-version = 1.06.00
Ext-ROM-version = 1.22.115 GER
Protokoll-version = 1337.38
------------------------------
please help me
first, read wiki
second, if you still not find an answer try MaUpgradeUT_NOID.exe for upgrade

Categories

Resources