Database Develop

GUUYYSS HEEEEELLLPPPPP

I've tried to upgrade my XDA 2s using PDA2k WWE 14000 176 11 CDL. I bought mine in Singapore. And using it in Indonesia.
First I just run the BaUpgradeUt and it says Device ID error. Then edit the RUU.conf. Run it again and still get Device ID error.
Second, I tried Using MaUpgradeUt_noID and it worked fine for the Radio but not for ROM and ExtROM. Then I put Radio.nbf and MS.nbf into different folder leaving only nk.nbf, EnterBL, RUU.conf, RUU.dll, GetDeviceData, MaUpgradeUt_noID in the upgrade folder. I try to run di MaUpgradeUt_noID and it stop when the progress bar reach 41%. It says ERROR 112: CE ROM UPDATE ERROR. Same thing with ExtROM.
Plz guys I need help.....

Also my bootloader is 2.07. Sorry I forgot to write it.

Any help would be appreciated guys......need urgent help here..plz

Read wiki:
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
Use the first method.

TheLastOne said:
Read wiki:
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
Use the first method.
Click to expand...
Click to collapse
still not working. I cannot use GetDeviceId coz it's only stuck in bootloader 2.07. Could you give me another way to revive this dead xda2s.
thx b4.

Flash it with the First Method (Quick/Easy) as this does not need the info out of devicedata.

Hi adbradwell,
Since you bought your device from Singapore, why don't you use the official Asia Upgrade to 1.40, since it is out. Get the shipped full exe from here. At least you can be certain you would not get any device / country error. Just my two cents worth tho. Cheers ^^
Btw, if you are stuck in bootloader mode, just perform a hard/soft reset to get out of it.

Think I have killed my dad's phone !! HELP

Was updating my dads SPV M700 to WM6 and have hit a problem ....
The rom image updated ok, and I used AX3L's 2.0.8.
Unfortunately during the GSM update the software crashed, and froze at 51%. I had to re-boot and now I can't use the phone.
When I re-set the phone it says No GSM at the HTC screen and then stops loading at the WM6 front page.
I can get into the Bootloader by pressing the Power/Camera/Reset buttons, but when I try to re-flash GSM is says error 270, corrupt image. I have tried several files with no luck.
I would appreciate a hand ..... My dad is going to kill me
Thanks
gaz_az

try press
power button + camera + reset
to enter usb mode
then reflash the radio again.
hope this works

You can try 2 other things!
Download the Radio ROM again- you may have had a downlaod glitch in the 1st one. V1.38 is the best one to try.
Download and install the offical HTC WM5 ROM- this should be a full ROM including Radio, so sometimes completes more effectively. If you are brave, you can them retry the WM6 flash!

since bricking a hermes i stopped taking chances doing rom upgrades via usb..
the method that is most reliable ad safe is... via SD card
extract RUU_signed file from the upgrade pack (use winrar) and then copy it to the root of a blank sd (mini or micro etc) and rename to TRINIMG.nbh ..enter bootloader and follow the steps.. its fast and most reliable

Ok - Thanks for the help, but no luck so far. I have tried the suggestions above !
Heres what I have done ...
Hard reset - no change
Tried to re-flash with WM6 and WM5 cooked roms, but an error comes up saying the images are corrupt. This happens with any image I try.
I have also tried a legit HTC WM5 rom upgrade image, but it doesn't work either. It gives an error at 1% saying invalid device ID.
What I can do it get into the standard bootloader screen, which shows I have a USB connection when plugged in. If I allow the phone to boot up it stops at the WM6.0 picture. It won't go far enough to allow me to get an activesync connection.
ANy more adivice would be greatly appreciated !
gaz_az

Next thing then, is to try and obtain a downloaded Orange M700 ROM- there are a few links hereabouts.
For some reason, your device seems to want only its home ROM. If that fails there are other methods before sending back to Orange!

I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??

well if you were my son, i would advice you,to buy a plane ticket for somewhere very far,leave the house while i sleep,and pray every day you have left in your life,for not find you on my way

uhm, question about boot loader and flash on boot loader mode.
I copy file TRINIMG.nbh to root card mini SD, and i can't go as you say...
always Tri colors screen....

gaz_az said:
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
Click to expand...
Click to collapse
You are running out of options
Your choices now are to go further down the 'fiddling' route, or give up and return the phone to Orange for repair. At least if its is stuck in bootloader, they may not spot that you have been meddling
If you want to play more, there are very few Trinity specific fixes, but possibly some of the questions/answers in the Hermes WiKi may help, though the Bootloader versions etc won't be relevant.
[Edit: When you are in Bootloader mode, what version numbers are showing on the screen?]

is it so wrong i was smiling when i read this.
does make me wonder if u told ur dad what u were going to do or whether u were trying to be cocky by giving him a better phone without him knowing.
all i can say is, UNLUCKY !

I must say things are looking bad - I think it would take an original orange SPV rom if I could get one. Been to the orange website, but no luck !! Anyone know if orange released one ??
Been looking at the Hermes unbrick thread. Is there a way to enter KITL debug mode in the trinity ??
G
P.S. Dad knew I was upgrading the phone, already did it once for him and it went ok. No sure he knew I could acutually kill it

No Orange haven't released an official rom.
Well Orange UK haven't Orange FR have, so unless he speaks and reads french that's not an option.

Well, French or not, you've probably got nothing to lose by trying to load the official French ROM
Go Here and click the Mise-a-jour link (which is French for ROM) and it will open a zip file download without the need to verify the IMEI number.
If that doesn't work, nothing will! If it does load, you will at least have a working phone, even if it is in French, and you can go back over the ROM update again, remembering to apply the SPL Bootloader first!

Still "not allow", i don't know what the hell Orange was doing with P3600?
Lock everything?........it's suck !!!

No luck with the French ROM. Same thing gives an error message about wrong device ID.
I am one step from chucking it in the bin. Any more last minute ideas ??

erh, bizzard,i can't use "wtty.exe" to view my CID ...
i tape "info 2"and it always appear
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
...............................
Someone have issue for that?
If i can view CID code,i think i can find the right ROM to re-vivre...all suck !!!

erh, hey guy, your boot loader is english or french? sorry if it's the most stupid question of the day......i think french device use french boot loader,right?
i mean, when screen tri-color appear, use mini SD card to flash ROM, the language it apprear itself is english or french.
p/s : i was telephone to the HTC center, and they say as usual, send it to the center repair.
For french user address is : be sure u have enough garanty which required.
send them and make them crazy.....
CIRMA ELECTRONIQUE
9A14 CHEMIN DE BARATEAU
ZONE INDUSTRIEL DE LA LANDE
33451 SAINT Loubès

If you can figure out how to compile splxploit, you can fix this, see
http://forum.xda-developers.com/showthread.php?t=308691

thank anyway,i will try it before tomorrow,cause i will send them my device for repair.

Error 246 Device not responding

I'd bought my htc p3600 pro (black, free from sim-lock & free from any carrier) from London.
As advised by TRINITYGUIDES.INFO site I tried to do HardSPL with all the three available HardSPL files, but of no avail.
When the HardSPL's progress bar comes(on pc) it gives a message on my phone " Enterbootloader.exe....This may harm your device...Do you want to continue.." I pressed yes & the process stopped & gave an error on pc "Error 246 Device not responding" & on phone screen showed the bootloader with
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
I did soft reset on my p3600 & its working as usual with it original spl infos.
I want to put official WM6 SEA version(ROM+RADIO) on my phone...Please help.

I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks

wingnutLP said:
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
Click to expand...
Click to collapse
Search is great function
http://trinityguides.info/index.php?option=com_content&task=view&id=37&Itemid=67

wingnutLP said:
Sorry!
I am an idiot.
Thanks
Click to expand...
Click to collapse
sorry I tried a Google search on the error message and came up with this thread!

wingnutLP said:
sorry I tried a Google search on the error message and came up with this thread!
Click to expand...
Click to collapse
Search more...
With this link:
http://www.google.com/advanced_search?q=+site:http://forum.xda-developers.com&hl=en&lr=&as_qdr=all
if you search error 246 you will get the solution on 11th answer.
Search more...

Have the same [Error 246]! How can I definitly fix it?
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo

Some specifications....
Sorry.... I have a P3600 White with Olipro 1.20 and rom Elias 1.9 SE Lite...

Tompo81 said:
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Click to expand...
Click to collapse
Before flash manually enter bootloader. After start the rom update utility. (As www.trinityguides.info suggest). You will not get error 246 any more

thanks for answer
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo

Tompo81 said:
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Click to expand...
Click to collapse
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)

Ok, now I really understand
Ok, this is a very good anwser, short and clear... thanks...
Ciao
Tompo

fktsndr said:
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Click to expand...
Click to collapse
When i connect my touch hd to pc in active sync mode, then shutdown device an run in bootloader (volume down and power button at same time) i get the tricolor screen and after a while i get the progress bar on my phone and on pc. But i stays on 0% and says 'update error' after a while.
please help

I Have the Same Problem the Status bar Freeze On 0% and nothing happened
Until the Update Error Message Displayed
Please Advice
Thank You
Note: I Have HTC Diamond2 (Topaz) Without Sim Louk

Hi Me has the trinity 3600 as a VPA GPS vodafone branding, and i get the same error message trying to run the bootloader and entering tricolor screen, ---> error 246 aber manually starting into bootlaoder and restatrting the romupdateutil.exe same error 260 no connention...
So you guys have a working version of the updating ?
And please remove all the links which are not working, linking a solve for the 246 problem, there are nomore links available...
thanks
Dome

I found a way to solve the problem 246 go in you mobile device, -->start -> settings-> connections ->USB to PC open this. Remove the hook @ Advanced networksettings activation! ---> click OK--> close
try again the bootloader etc, then on the tricolore reboot screen is shown USB in the lower white field and the bootloader can do its routine complete.
Have Fun with flashing the phones!
Testet with original German Vodafone available ROM " vpa_comp_gps_RUU_Trinity_VF_DE_1_23_162_4_6275_1_29_00_01_13000_108_Ship.exe "
testet with ZackMcRofls superfast german rom " RUU_Trinity_GER_1.23.162.2_GPS_v3f_by_ZakMcRofl "
testet with
" htcp3600_RUU_Trinity_HTC_GER_1-23-407-2_103_6275_1-38-00-11_108 "
First was Zack´s rom, 2nd. was Original Rom, 3. was Trinitys rom, after trxing all, i flashed Zacks Rom again, it was the best in my view.
Thank you verymuch, bb

[Q] unlock rom image for hp 6515

Hi
I have a cingular hp 6515a . I cannot unlock it.I need an unlock hp 6515 rom image.please help me.

Unlock hp 6515
Thats very easy.
1: Download the (upgrade and unlocked) ROM from HP's website
2: HardReset your phone, but leave it in the first welcome screen (before the align screen and so)
3: Connect the phone to your PC, and wait for the connection to be established.
4: Run the downloaded Upgrade package (from HP), the phone will show a bootloader-screen.
Sometimes, the phone will not accept the upgrade program.
In that case do the following, but nothing else!
1: Disconnect the phone and soft reset it (it will come back into the bootloader)
2: Close the HP-upgrade program with taskmanager on your PC
3: Reconnect the phone to the PC
4: Rerun the HP ROM upgrade program.
Now your phone will show its upgrade status. It will take a while (about 20 minutes or so), but afterwards you will have a clean unlocked 6515.
I did this with several locked phones (especially Vodafone) from international sources.
Above will work fine, on every PC with Active-Sync (in my case 4.5) installed.
I assume, you will have a backup, made by the SIP-backup program on one of your memory cards. You can restore it after you've upgraded your phone

SKU error,, did not work

Unlock HP 6515
Did you use the rom you download here: HP 6515 ROM upgrades ?
I did it again today, but with a soft reset of the 6515 and shutting down the upgrade program with taskmanager. Do NOT Hard-reset the device or reboot your computer! Before restarting the upgrade, the computer has to reconnect to the 6515 although it is in the bootloader mode.

My hw6515 is dead after the upgrade to 1.21
Hi guys,
I tried my cingular hw6515a to update the ROM to 1.21 unlocked ROM, it went successful but when booting it shows the initial setup and it hung on the second step "Pop-up Menus" and it doesnt show up any next button. What should i do now, please help me..
Thanks a lot in advance.

Has anyone managed to get this to work on a 6515 "A"? When I tried it I got an error message that said something like "Incorrect device SKU". I then decided to try upgrading to 1.20 which went smoothly. However, I still get the same SKU error message when trying to upgrade to 1.21. Is there a way to force it into bootloader mode? Anyone know some trick that I'm missing?

ROM Update 6515
SKU-error means wrong language.....

deivasankar said:
Hi guys,
I tried my cingular hw6515a to update the ROM to 1.21 unlocked ROM, it went successful but when booting it shows the initial setup and it hung on the second step "Pop-up Menus" and it doesnt show up any next button. What should i do now, please help me..
Thanks a lot in advance.
Click to expand...
Click to collapse
Retry the update, or downgrade to 1.20

I Think Not..............
Accordint to i know sim/Net locks r stored on different partison or ROM image of WM so when u upgrade it it dont removes sim/net locks..............

Hi there,
I've tried upgrade from 1.04 to 1.21WWE, but the upgrade process died on 12.5%.
I use the original rom upgrade from HP with ActiveSync 4.5 on XP.
I've tried many times to restart the upgrade process, but it fails on .1%.
Cann someone tell me where I can find the original 6515.bin. I've try to gogole it but with no success.
Thanks in advance.

cellsolution said:
Accordint to i know sim/Net locks r stored on different partison or ROM image of WM so when u upgrade it it dont removes sim/net locks..............
Click to expand...
Click to collapse
I've done it several times. The HP Roms contains also the RadioROM.
If you just think it cannot done... Why don't you give it try...

Arruor said:
Hi there,
I've tried upgrade from 1.04 to 1.21WWE, but the upgrade process died on 12.5%.
I use the original rom upgrade from HP with ActiveSync 4.5 on XP.
I've tried many times to restart the upgrade process, but it fails on .1%.
Cann someone tell me where I can find the original 6515.bin. I've try to gogole it but with no success.
Thanks in advance.
Click to expand...
Click to collapse
What language do you use?
For WWE you wil find v1.21, v1.20, v1.12 and v1.00 here.

SKU ERROR help pls

cellsolution said:
Accordint to i know sim/Net locks r stored on different partison or ROM image of WM so when u upgrade it it dont removes sim/net locks..............
Click to expand...
Click to collapse
So how can we solve this problem?

Unlock and language change- this is how it worked for me!
This method worked for for an iPaq hw6515 after many long nights, but may be good as well for others:
Do this only from an Windows XP OS.
Make sure you have up to date ActiveSync from Microsoft!
To Unlock,
Just reflash your iPaq with the THE SAME language from HP official support site: h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=501212&lang=en&cc=us &prodTypeId=215348&prodSeriesId=501209&taskId=1 35
Connect your PDA to the computer and check it is in state connected in ActiveSync.
Download the current language ROM from the provided link, unpack, , and follow the instructions.
This official tool will do everything for you!
When it completes (~30 minutes), your phone will be unlocked.
After that if you need to change the language, follow this instructions:
How to change the language in your iPaq:
Here is the detailed process completed, borrowed from Barr :
1. Download and extract BOTH current and desired ROM language pack from HP site to the computer. Unpack them to different folders.
2. Establishing connection with the computer, copy EnterBL.exe (from desired language ROM folder) to the mydocument folder of the PDA.
3. Run the EnterBL.exe from the PDA. (Now your PDA will go to Bootloader mode).
4. (before executing step 4, prepare for step 5 since step 5 will have to be executed right after step4). From your PC, start updating the current ROM by lunching hpRUU.exe of the current installed language of your PDA.
5. Right after step4, when it will start updating, copy all the data (*.nbf) files of desired/intendedlanguage ROM pack to the current ROM pack. (the Rradio.nbf may be skipped if the device is already unlocked).
6. At the end of copying, it might show an error message, press OK to ignore.
7. The phone will restart!

Arruor said:
Hi there,
I've tried upgrade from 1.04 to 1.21WWE, but the upgrade process died on 12.5%.
I use the original rom upgrade from HP with ActiveSync 4.5 on XP.
I've tried many times to restart the upgrade process, but it fails on .1%.
Cann someone tell me where I can find the original 6515.bin. I've try to gogole it but with no success.
Thanks in advance.
Click to expand...
Click to collapse
Same here i reflash again last night but upgrade process fails on .02%

Need HELPPPP plzzz

hey, im new to all this, the tutorials dont make sense to me, atm i know my device is:
-tmobile mda vario
-unlocked
-G4
and is rom verion 3.8.2.1 wwe
i tried to upgrade it with SNN Diamond edition, but when ever i tried this, i got to the part where it starts to flash, the mda vario screen goes to the screen with the three colors but then on my laptop it just crashes and seys something about it is not responding and you have to close it, i have tried with other roms, but same thing occurs
can someone plz help meee

use softspl

ok thanks, will it work with unlocked pdas?

need help agen lool
i tried updating the rom with TNT,19213 professional
and error [300] invalid update tool occured
it says this update utility cannot be used on your pda phone.please get newer update utiltiy plz plz help

You have to use SoftSPL, you can get it HERE
In this folder, you copy the "nk.nbf" of your favourite WM6 (and only this file), then start with "START-sSPL.exe" (make sure you're connected via ActiveSync).
When you read this here before, you know everything you need!

Probably you are not following the instructions and doing it correctly,try to go according to the guide,if it still doesn't work,it sometimes happens that SoftSPL fails,than you better do it through 'HardSPL'