HELP - MY QTEK IS DEAD AFTER UPDATING - MDA III, XDA III, PDA2k, 9090 Software Upgrading

HELP . I was updating the ROM of my QTEK 9090 and during the procedure the SYSTEM of CLIENT froze and I had to interrupt the updating.
Now I have on the screen of the QTEK a "USB - V2. 07" line and the QTEK doesn't react to any imput.
I tried also the soft reset and the hard reset (soft reset + ON/OFF button ?)
What can I do?

hi,
don't be affraid bro...u entered bootloader mode :wink:
now do the following:
1-download an original QTEK rom from ftp.
2-hard reset ur phone and u ll see serial on the top,bootloader version on the button...
3-put the cradle DIRECTLY into usb port NOT THROUGHT HUB.
4-put the charger in ur cradle.
5-put ur phone in the cradle,u ll see that the serial that was on the top turned to usb,then your desktop/laptop will detect a new device,and install it.
6-reflash with ur original Qtek ROM....
hope i've helped
let me know the results...i would love to help u in case those procedures didn't work
RAGO :lol:

Yes it worked. Thank you very much.
GEOPDA said:
HELP . I was updating the ROM of my QTEK 9090 and during the procedure the SYSTEM of CLIENT froze and I had to interrupt the updating.
Now I have on the screen of the QTEK a "USB - V2. 07" line and the QTEK doesn't react to any imput.
I tried also the soft reset and the hard reset (soft reset + ON/OFF button ?)
What can I do?
Click to expand...
Click to collapse

Related

Battery Problem after upgrading with new uk t-mobile rom

Hi,
i upgraded my charmer with the new uk t-mobile rom and my nproblem is that the battery does not charge,and i don't know how to do
have you some suggestions???
Waiting your answer,thanks a lot,Antonio
Hi did you get a answer
Hi I have the ssame problem, did anybody come up with any ideas ?
Cheers
TBW
Battery Problem
Hi, I have too this problem with wm6 rom have you some suggestions??? pleas
Hi...nobody can help us???
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
vlodeck said:
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
Click to expand...
Click to collapse
i have the same problem and doesn«t work for me
Then my guess is you flashed a ROM not intended for your device.
now how i can solve this?
Reflash a charmer rom? And if that doesn't work, try a prophet WM5 rom.
it says that i don't have enough battery, is lower than 50%
Use the NO_ID RUU version instead.
i already try a few roms and i can't flash the pda with none of them
You will need to reboot in BootLoader mode first (powerkey+camera+reset).
hello!
a downgrade my Charmer and now the battrery is 0%, when i connect to usb phone don't want to start, on charger it startet but battery dont want to charge. help pls ...
Hi,
I have solve this problem but I'm not sure how I've done this.
1. dowlnoad cab from this link http://forum.xda-developers.com/showthread.php?t=327988
2. I have use program Wizard Service Tool and clear everything what is possible including format.
3. reset
4. format after strart camera+record+soft reset
5. after reset bootloader mode, and first time my phone has connet in BLmode with USB.
6. Then I have run original T-mobile RUU and it's working
My battery has been on 0% in system as well but after downgrade battery states about 70%
have a same problem.
did anybody else solve this problem? anybody used SD flashing method?
i've solved problem partly - now battery charges, but i can't start it without power supply. so what have i done:
1) i've downloaded ShellTool_bugfixed.zip (you can easily find it google).
2) unpack it.
3) copy Cert_SPCS.cab and EnableRapi.cab to you WM and install
4) extract nk.nbf from original Charmer ROM into ShellTool folder
5) start ShellTool.
6) press Get ROM Info
7) press Extract OS
10) press Flash OS
11) press ОК
Followed all this steps, now i've got an original charmer os, but bootloader is still from previous crap ROM. so there is trouble with starting it up. If you phone doesn't start even when you charging it from power socket, so try to wet contacts on battery - it should work.
now i thinking how to re-flash bootloader, cuz it cannot enter into bootloader witout power supply from socket. It's no possible to flash it from PC, cuz it cannot enter a booloader plugged into USB port. It seem that there is not enough power impulse to startup.

SD-Card Rom for Charmer

Hi guys,
I have a big problem with my charmer.
At the begining I tried to work with my charmer and it was OK, but after a short time it resets from alone. It was the same situation everytime, when the charmer was starting and I did the calibration of the touch screen it was reseting always as soon as I pressed the cross on the right bottom.
Next step was to flash the ROM - it was sucessful, but the same situation
-> Reseting at the calibration.
I did once again a flash but it resetet during flashing and now I have the situation, that I can enter boot loader but as soon as I connect it resets.
Battery I checked -> It is OK.
So does anybody have a Rom on SD card ? -> I have no other joice, this is my last chance to get it running again.
Thanks for your help in advance
Best regards
Helldriver
Hi
1. Kill (task manager) wescomm.exe (this is related with activesync installed on your PC).
2. Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
3. Now connect your USB cable to your phone
4. Download T-Mobile compactii_aku2.0_05-2006 rom and Flash it works for me
jerry
Not working with USB
Thanks for your comment, but it is not working, due to the fact that the MDA tripps as soon as I connect the USB cable (even if I kill the wecomm.exe).
Therefore my only chace is the SD-card
So if anybody has a ROM on SD card, please help me getting my Charmer running again.
Regards
Helldriver
Hi Gents
is there somebody who can help me ?
I really need a SD-card rom
Thanks
Helldriver
Sorry ,but I am noob. How can i flash it??? And how can i kill wescomm.exe???
Rom backup
Hi all,
Still searching for the SD ROm image... Can someone upload?
Please...

Big Problems!!! System is freezing all the time!

Hello,
now the time is come that I really need your help.
Everytime when I try to turn on my MDA Vario 3 the system is crashing after the Bootscreen. I could do nothing exept turn of the device.... I already tryed it with a lot of hard and soft resets but it still wont work.
When the PPC is connected to my PC its going to freeze in the main menu from Active Sync (I dont know why this pops up even before I could enter the PIN code)
and when the device isn't connected to the PC the system is going to freeze in the HTC Home screen (at the point before you enter the Pin code normaly).
I also couldn't flash the rom because even wehen Active Sync pops up the device could not connect to the PC...
So when somebody have an Idea which coul help me, just let me know!
PS: Sorry for the bad english
DerGregen said:
Hello,
now the time is come that I really need your help.
Everytime when I try to turn on my MDA Vario 3 the system is crashing after the Bootscreen. I could do nothing exept turn of the device.... I already tryed it with a lot of hard and soft resets but it still wont work.
When the PPC is connected to my PC its going to freeze in the main menu from Active Sync (I dont know why this pops up even before I could enter the PIN code)
and when the device isn't connected to the PC the system is going to freeze in the HTC Home screen (at the point before you enter the Pin code normaly).
I also couldn't flash the rom because even wehen Active Sync pops up the device could not connect to the PC...
So when somebody have an Idea which coul help me, just let me know!
PS: Sorry for the bad english
Click to expand...
Click to collapse
Flash from bootloader. Make sure you're hard SPL though, or that it's a compatible ROM for your CID.
have you tried:
Start->Settings->Connections->Usb to PC and clear the 'Enable advanced network functionality' checkbox ?
manuv1615 said:
have you tried:
Start->Settings->Connections->Usb to PC and clear the 'Enable advanced network functionality' checkbox ?
Click to expand...
Click to collapse
Hello,
I could not try this option because I couldn't do anything exept restart/turn off the device.....
Now I found out that I can flash the Rom with the bootloader but the problems still where the there with every rom... And I tryed a lot...
After the 3. or 4. restart with the new rom the problem pops up again....
DerGregen said:
Hello,
I could not try this option because I couldn't do anything exept restart/turn off the device.....
Now I found out that I can flash the Rom with the bootloader but the problems still where the there with every rom... And I tryed a lot...
After the 3. or 4. restart with the new rom the problem pops up again....
Click to expand...
Click to collapse
You said that you could enter bootloader menu right?
now tell me, whats written there?
i'll wait here,.
Theres a 4 colour screen (red, green, blue and white)
And in the red bar is a text with a yellow font:
KAIS139 MFG
SPL-1.0.0liPof
CPLD-8
And below in the withe bar stands "Serial" or "USB.
What rom did you use?
try HardSPL 3.56 by jockyW,.
then reflash your ROM,.

Stuck Wizard

Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
sephiroth_vg said:
Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
Click to expand...
Click to collapse
u prob. d/c ur cable when you were flashing a rom
this happened to me
the solution for me was to just reflash a rom
Hello,
sephiroth_vg said:
Hey guys i have a Imate k-jam..but its stuck like hell..i mean i tried just about everything i could to get it out of bootloader...whenever i press the power button the phone just automatically goes into bootloader mode..and nothing loads..i tried buttons roms..but it stuck at 98%..den i tried the other rom in a walk thorugh and it upgraded and changed my IPL from 1.01 to 1.06 (SPL is the same 1.01) so what should i do? I tried to install a official rom from Imate support but it says that it cant be installed in my device ..i even tried the SD backup method but it doesnt work as well and the app (on computer) just hangs even though it shows the table and other allocations.. PLZ HELP!
Click to expand...
Click to collapse
Do this:
Step 1. You`re phone is in bootloader mode (3 color screen) ok? Connect your phone to PC.
On Desktop go to My Computer icon -> Right Click -> Select Manage from the list.
Computer Management -> Select Device Manager.
On the bottom of the list you must have Windows CE USB Devices, if it`s there then you`re phone is connected! If you`re phone ain`t connected please right click on Human Interface Devices, and click on Scan for hardware changes!
Step 2. Go to http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades and get the Aku 3 Official ROM and flash it to you`re phone. (T-Mobile UK 3.8.2.1 WWE (AKU 3.3 & 3.0) OS:3.8.2.119 Radio:02.69.11)
In case you don`t have battery more than 50%:
Step 3. Let`s charge it! Phone must be off. Put the charger in... and hold the power button until you`re phone starts charging. It take`s about 10-15 seconds. Max. 30 seconds and some times 1 minute.
If this doesn`t help you, please do this again: http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Regards! & Good Luck!
eXPLOiTeD said:
Do this:
Step 1. You`re phone is in bootloader mode (3 color screen) ok? Connect your phone to PC.
On Desktop go to My Computer icon -> Right Click -> Select Manage from the list.
Computer Management -> Select Device Manager.
On the bottom of the list you must have Windows CE USB Devices, if it`s there then you`re phone is connected! If you`re phone ain`t connected please right click on Human Interface Devices, and click on Scan for hardware changes!
Step 2. Go to http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades and get the Aku 3 Official ROM and flash it to you`re phone. (T-Mobile UK 3.8.2.1 WWE (AKU 3.3 & 3.0) OS:3.8.2.119 Radio:02.69.11)
In case you don`t have battery more than 50%:
Step 3. Let`s charge it! Phone must be off. Put the charger in... and hold the power button until you`re phone starts charging. It take`s about 10-15 seconds. Max. 30 seconds and some times 1 minute.
If this doesn`t help you, please do this again: http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Regards! & Good Luck!
Click to expand...
Click to collapse
the phone doesnt giv any nidication tht its charging...and when i connect it the ruu doesnt detect the phone (it is shown in device manager though)...and my device is CID locked (aka no chnages made to anything since it was bought).. the only indication that its charging is that the mobile gets a bit hot after a while..and i guess that means its charging..
also the upper right hand corner there is ruu or rru written in the corner..(in bootloader)
Hello, Maybe this helps....
sephiroth_vg said:
the phone doesnt giv any nidication tht its charging...and when i connect it the ruu doesnt detect the phone (it is shown in device manager though)...and my device is CID locked (aka no chnages made to anything since it was bought).. the only indication that its charging is that the mobile gets a bit hot after a while..and i guess that means its charging..
also the upper right hand corner there is ruu or rru written in the corner..(in bootloader)
Click to expand...
Click to collapse
ok... if it`s shown in device manager the the phone is detected by the PC that`s in bootloader mode and connected....
If your phone is CID locked... i have to flash to a official IMATE K-JAM ROM.... you can` find some here... http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
And when you try to charge the phone... orange light must apear, if you say that it don`t indicate... then i think it doesn`t charge...
Regards & Good Luck!
man sadly no orange light.....the screen just turns white when i plug it in...sometimes even that doesnt happen...but a VERY RARE (2 times) the red light flashed for just a fraction of a second...and the links for imate roms are dead..i tried access to the ftp site and there is nothing left in the imate folder at all...anyways..i tried to flash the rom from imate website...even that wouldnt flash..says phone not detected..

help me: Your OS ROM isn't customized for your hardware.

help meeee, i just flashed my diamond with this rom: RUU_Diamond_Dopod_CHS_1.39.706.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe and after the restart it brings the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I've read in other posts concerning this message that i just need to take out the battery and wait 10-15 minutes. does not work for me. i still get the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I tried to flash it again, but the problem is that the diamond is not recognized on my computer anymore it looks like it doe sent have any usb connection capability any more.
Please help me.
Thank you soo much in advance.
P.s. Is there a combination of buttons to press so i can get the diamond in a flash mode so i can flash the proper OS on it?
come on guys, did i really brick my phone? does anyone have any idea what i should do now?
i had this same problem - take the battery out for about 2 minutes and then power it back on. that _did_ work for me. if you have done it and it didnt work i dont know.
simple question
do you have an original diamond or a dopod?
if you have an original diamond .... you flashed a dopod ROM on it..., did you put a HardSPL on it?
if you have a dopod...really dont know what happens with those ): sorry
Mariano.
i have an original diamond.
yes hardspl was on it.
i can go to the hardreset options by presseing home, vollume down and reset button. but this still doesent let me flash the orignal OS on the system.
what can i do, i really need your help guys!
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
I had the same problem
and your solution (dear gmesut) works on it
only i can say thanks
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
good tip,it responded in my hd mini
thanks gmesut

Categories

Resources