Needed - mtty ver 1.11a to backup Blue Angel Rom - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hi,
does anybody have mtty ver 1.11a?
(Multi-Port/USB TTY ver 1.11a)
Apparently this version will detect an XDA IIs
I'm trying to backup my ROM the links I've found to mtty.exe give me an older version, when I use this it doesn't detect \\.\wceusbsh001
When I go into bootloader mode, it is v2.07, but that is as far as I can get in the older mtty.exe
The links in Wiki lead to en.PDAMobiz.com, however the links here give an access denied message. :?
The link calls this program rompdate
I've done searches of the forum which informs me its been renamed and lead to the link
ftp://xda-developers.com/mtty.zip
but I get a page can not be displayed message. :?
Please help!
Regards
Gerard

Aha solution found
I found a better post!
The link in Wiki left out a step.
An alternative set of instructions can be found at
http://en.pdamobiz.com/en/forum/PDAforum_posts.asp?TID=62&PN=1&TPN=2
The problem wasn't the version of mtty, but was actually in killing active sync on my PC. Originally I used (ctrl + alt + del) and closed the application. But the process wcescomm.exe was still running. Once this was killed. The mtty.exe didn't automatically detect \\.\wceusbsh001 this needed to be typed in manually
Hopefully this helps anybody else who spent hours looking at dead links
Gerard

Thanks! I was looking for something like that before I tried my hand on WM5...

Related

can't format extRom..

hi people...
i tried to install a wm5 and a wm6 rom in a qtek 9090 but i can't format and merge ExtRom... i tried to use the rom unlocker found in the a77ila wm5 rom pack but i have a lot of error during unlock.. and when i try to format this error will show: FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed!
i tried with xda-developer unlocker but an unable to find exe file will show..
and repart_doc still not work...
anyone can help me?
my device:
qtek 9090
SO WM2003SE ver. 4.21.1088 (Build 15045.2.6.0)
ROM : 1.40.04ITA
Radio: 1.12.00
Prot Ver: 1337.42
ExtRom ver: 1.40.153 ITA
tnx in advance... and sorry for my bad english
1. You cannot reformat extROM without unhiding and unlocking it first. Follow the procedure step by step. (remeber aboutsoft reset
2. Correct links to both tools as well as the procedure you can find on Wiki (http://wiki.xda-developers.com/index.php?pagename=Helmi - Installation)
3. Report effects.
3b. Your english is OK
here i am...
followed tutorial step by step...
1. installed the unlocker
2. launched unhide
3. soft reset
4. launched unlock
5. system displays a windows named debug showin ERROR: press OK
6.another system window named debug showin FL_IOCTL_BDTL_HW_PROTECTION press ok
7. another window saying a peripheral connected to system in not working press ok
8. a debug window saying extrom unlocked
9. soft reset
10. launched repart_doc
11. error window saying "FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed" press ok
tried also without soft reset at point 9. same results..
i only see Ext_Rom in memory page of Setting but still remain full
------------------------------------------------------------------
Finally solved...
i don't know why but ita extrom can't be formatted...
so i used an escamotage... upgraded qtek9090 with this rom BA_TMNL_14200_119_11300_Ship
After used unlocker and repart_Doc and all goes on....
now go to upgrade to HELMI_BA_WM6_R0_Public
hiya
i cannot format my DOC too, i got the same error ,
i used TASK 28 under MTTY , but still i'm getting this error.
anyone can help with this problem ?
Hiya
I was searching XDA-DEVELOPERS website about 2 days to find a solution for this problem, I have an I-mate PDA2K, i used all EXTROM tools on this website like this:
1- Installed EXTROM_tools,
2- run UNHIDE ,
3- then run UNHIDE,
4- Soft Reset,
5- now i can see Extended_ROM on my file explorer, i can read it , and able to write on it ... copy paste ...
6- run REPART_DOC.exe on my device,
7- tried many sizes like 128kb, 1024, 2048, 512, 61000, .................
but on this step i always get the god damned FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed,
i finally used Task 28 under MTTY but nothing happened, still have this problem,
No Wayyyyyy ! No wayyyyyyyyyy to repart my DOC size, .... noooooooooooo wayyyyyyyyyyyyyyyy
anyone going to help me plzzzzzzzzzzz ?
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
SilverSamurai said:
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
Click to expand...
Click to collapse
Hiya
I'm not a braincracked one, I'm a computer software engineer and i write CNC machines programs, so i don't need to someone to teach me instructions !!!! i did all, but i got FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed. !
find me a good solution plz !
and i thought landmark's the only one who is bossy...
if you dont need instructions then what are you looking for in here??? duh!!!
you're both at the same level of intelligence... are we downgrading humans now?
P.S.
look at the end of the third post... that is solved.
Everybody is allowed to name themself software engineers nowadays?
Please people start behaving like grown up's we are no longer in kindergarten.
Please:
- listen to each other
- be prepared to be wrong
- try explaining your problem in another way
- but most of all don't try to solve your listening problems by yelling and cussing to each other.
TIA, Flar

Cant install HardSPL - advice on what im doing wrong please

Hi, hopefully this is me being stupid/uninformed rather than some new weirdness but im trying to install HardSPL to allow me to put in a 6.1 rom, but not having any luck. Ive read the guides and as far as I can see am following them but I stay stuck on the tri-colour/usb screen on the device and "Please make sure ActiveSync is enabled (GREEN icon in systray) and hit ENTER to start..." screen on the PC and dont seem to get any further than that.
The steps ive been following are detailed below, I have a new generic UK HTC device running WM6.0. Any help is appreciated. Many Thanks.
So this is what im doing...
Boot phone after removing battery, sim & memory card
R 1.27.12.32
G 22.45.88.07H
D 1.56.00.00
connect PDA
Shows connected in taskbar, icon green
run either JumpSPL1.56KAIS.exe or JumpSPL1.93KAIS.exe on PDA from 'my device\SPL' folder
Hit 'yes' & 'continue', get the tri colour screen, with USB at bottom
after about 20 secs usb disconnects and taskbar icon goes grey
unplug, ding dong
wait 10 secs, dong ding
I have a mobile device in explorer but with no folders under it.
Open active sync (grey still) settings, after aprox 1 minute settings dialog appears and uncheck 'allow USB connections'
run 'kaiser-HardSPL.exe' on the PC
get the blurb, 'Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...'
Hit enter
a pput.exe icon appears on desktop (where im running it from)
But nothing else happens from here??? I end up unplugging, removing battery and rebooting PDA to the original 6.0 settings.
Whats going wrong?
**This is NOT a flame, just a free lesson**
You are making some mistakes...
First, you didn't post in the HardSPL thread. A new thread should not have been created.
Second, depending on which version of HardSPL you are trying to install (I'm assuming HardSPL v1.1), you are not following the correct steps.
Based on the steps you are following, you appear to have read several different HardSPL threads, and you are combining instructions from them plus the SIM Unlock thread.
At the top of the Kaiser General section, you will see a thread named "**BEFORE YOU POST START HERE** FAQ, Wiki, Stickies & Tutorials - Suggestions Welcome!". The answer you seek is in there.
Good luck.

Help...Can Not upgrade my O2 XDA IIs to either WM5 or WM6

Gentlemen
I am new here, in the past 1 week, I have read a lot documents here, thanks to you guys create such a wonderful forum and great articles, I also download a lot of file from here try to upgrade my XDA IIs to WM6, tried so many times on different version, but all failed.
Here is my XDA IIs info, hope someone here can give me a hint on what's the problem and how should I fix it... Thanks
Windows Mobile 2003 second edition, Version 4.21.1088 (Build 15045.2.6.0)
ROM Version: 1.40.00 WWE
ROM Date: 03/10/05
Radio version: 1.12.00
Protocol version: 1337.42
ExtROM version: 1.40.923 WWE
CPU: Intel PXA263, speed 400 MHz
RAM SIZE: 128MB
Flash size: 32MB
Flash chip type: 28F128K3
Data bus: 32 bits
Storage size: 43.26 MB
Thanks a lot
i have the same problem too..can anyone please help us out..wanted to upgrade from WM2003 to either WM5 or WM6 so i can put some of those iPhone theme on my phone..thanks in advance..(my phone details below)
?
thats messed up nobody responds cuz i was thinking about update myself but was worried i'll mess up major
window mobile 6.1 for xda lls
vfan3388 said:
Gentlemen
I am new here, in the past 1 week, I have read a lot documents here, thanks to you guys create such a wonderful forum and great articles, I also download a lot of file from here try to upgrade my XDA IIs to WM6, tried so many times on different version, but all failed.
Here is my XDA IIs info, hope someone here can give me a hint on what's the problem and how should I fix it... Thanks
Windows Mobile 2003 second edition, Version 4.21.1088 (Build 15045.2.6.0)
ROM Version: 1.40.00 WWE
ROM Date: 03/10/05
Radio version: 1.12.00
Protocol version: 1337.42
ExtROM version: 1.40.923 WWE
CPU: Intel PXA263, speed 400 MHz
RAM SIZE: 128MB
Flash size: 32MB
Flash chip type: 28F128K3
Data bus: 32 bits
Storage size: 43.26 MB
Thanks a lot
Click to expand...
Click to collapse
-------------------------------------------------------------
i already upgrade my xda lls to window mobile 6.1 and im very like this new roms..before this im planning to sale my xda.but since i use this new roms,i dont want to sale it anymore.thanks to master phoenix to pose the roms at him blog. You must have usb or cradle to do this.just follow the instruction there very2 carefully.
download here :
Go to http://pinoytopdownloads.blogspot.com
you can also go to this forum to see another review
http://www.gsmarena.com/o2_xda_iis-reviews-933.php
good luck
[email protected]
spyrgyro said:
i have the same problem too..can anyone please help us out..wanted to upgrade from WM2003 to either WM5 or WM6 so i can put some of those iPhone theme on my phone..thanks in advance..(my phone details below)
Click to expand...
Click to collapse
----------------------------------------------------------
i already upgrade my xda lls to window mobile 6.1 and im very like this new roms..before this im planning to sale my xda.but since i use this new roms,i dont want to sale it anymore.thanks to master phoenix to pose the roms at him blog. You must have usb or cradle to do this.just follow the instruction there very2 carefully.
download here :
Go to http://pinoytopdownloads.blogspot.com
you can also go to this forum to see another review
http://www.gsmarena.com/o2_xda_iis-reviews-933.php
good luck
[email protected]
I don't know if I toasted my XDA
I have an XDA IIs. The biggest problem I think that I made was to use Windows Mobile center since I am using a Windows Vista OS.
I was about to install the windows 6.1 from pinoytopdownloads when suddenly, it stopped and continuosly displayed Serial......version 2.07.
Did I toast my ROM or did it just become blank because Windows Mobile Center disconnects once the phone started changing it's OS?
I have not tried checking if activesync 3.7 on a Windows XP application can still recognize the O2 Xda IIs in that state.
If anyone can guide me or give help regarding this, I will greatly appreciate it. thanks.
try using XP with active sync 4.5 and start the process from the top, hard reset first your BA and put it in bootloader mode...that should work
Upgrading Blue Angel using Vista (without Mail Button)
Hy everyone,
Yesterday I had a bit of a struggle trying to upgrade my SPV M2000 (aka Blue Angel) but in the end it worked.
As you guys are having some trouble too, I'm going to post the way I did it and hope that it works for you as well..
Note I: This steps worked for me but there is no guarantee that they will do so for you too and everything you try is at your own risk. However I am sure, you are all aware of this and really hope that this is going to help you.
Note II: My Laptop runs Vista Business, my BA WM2003 non-SE. I modified the installation process as the mail button on my BA is not working anymore, preventing me from following the normal instructions found in the wiki.
First of all (Prerequisites):
- Ensure Windows Mobile Device Center (WMDC) is installed and updated to the most recent version. The latest version is 6.1 which worked fine for me.
- Get the drivers for the BA, to be found in the wiki
- Get MTTY 1.4.2, attached to this post
- Get the ROM you want to install, I used Sun Dream's WM6.1 which can be found in the wiki as well
Now, to the task:
To begin with we can follow the instructions given in the wiki for ugrading to wm6 using vista, so I'll just copy&paste those steps from there:
4. Put your device into Bootloader mode by pressing and hold the "Power" & "Record" buttons, and then press the Reset Button.
5. Connect the phone to the sync cable/cradle USB. (Now you can see "USB" at the top of your display and numbers (2.06 or 2.07 at the bottom) You may need to remove SD/MMC (memory) card
6. Now navigate into the WMDC (Start -> All Programs -> Windows Mobile Device Center)
* Click on the "connection settings" menu icon
* In the connection settings menu uncheck "allow USB connections" then press OK.
* Now exit the WMDC and return to the desktop
7. Go into the start menu and type "Services", this will take you into the local services dialogue and show a list of all services either running or registered with your pc.
* Scroll down the list and make sure these services are present:
* Windows Mobile-based connectivity
* Windows Mobile 2003-based connectivity
* If these services are not started then double click each one and set them to Automatic start by clicking the "startup-type" drop-down menu and selecting automatic then click the start button in the same window, apply the setting by pressing OK.
* Return back to the desktop again
8. Go into the start menu and type "Device Manager" then run, this will take you into the device manager.
* Click the "+" symbol next to "Mobile Devices" and double click on "HTC USB Sync". (Note: In my case this was labelled "Microsoft USB Sync")
* This will bring up the properties of the currently connected device.
* Go to the "Driver" tab and click "Update Driver".
* Click "Browse My Computer for Driver Software".
* Select "Let me pick from a list...."
* Click the "Have Disk" button.
* Click "Browse" and navigate to the AS_DRIVERS folder we created earlier.
* Now select your file
o Vista 32bit users select the file "wceusbsh.inf"
o Vista 64bit users select the file "wceusbshx64.inf"
* Then click Open.
* Click next and the driver will be installed (wait a moment).
* Press close and escape back to the desktop now.
Click to expand...
Click to collapse
Next Steps, different from those described in the wiki:
9. Go to the task manager and kill the wmdc.exe process
10. Run MTTY; select the USB option from the dropdown list
- There is also a USB button but the instructions I found said NOT to use it, so I did not test it
- Apparently, the option could also be called something like WCEUSBSH001, but always has to contain USB. In my case it just said USB
- If you do not get a USB option something is not connected correctly, ie it will not work with the stock drivers Vista uses
crabiorc said:
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
Click OK
Run following commands:
- [press enter first to get USB> prompt]
USB>
- Type "set 14 0" without the quotes to tell bootloader to boot the OS after reset. (then hit Enter)
USB>set 14 0
HTCST ÚÈHTCEUSB>
- Type "task 28" to get your device formatted (hit Enter and wait for a little)
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
- Type "task 0" to ask your device reboot (hit Enter)
USB>task 0
USB>
Click to expand...
Click to collapse
Next Steps:
11. Take the phone off the cradle. I am not absloutely sure anymore, but I think it still was in bootloader mode at that point. If that is the case just soft reset the device.
- When the device has rebooted it will ask you whether to flash some settings (can't remember which..) about 3 times. Just answer no to all of them.
12. Restart WMDC and re-allow USB connections (under connection settings)
13. Reconnect your device to the cradle and start Active Sync on the Blue Angel
- Make sure your device is shown as "connected" in WMDC
14. Start the ROM installation.
Note: Using "BaUpgradeUT.exe" resulted in a Device ID error. In this case you have to use a version which does not check the ID codes. I used the version attached to this post
15. When the installation is finished, the dialogue on the computer says to cold boot (hard reset) the device.
- If your mail button is not working, just soft reset the device (what I did)
- If your mail button is working you may attempt this. (Please report back!)
I have not yet gotten through really testing the device and I never had a WM6.1 device before, thus no basis for comparison. From the first impressions the soft-reset at the end did not cause any problems and everything seems to be working fine.
16. You're done
Whew, this has gotten rather long. If this instructions work for you, please let me know!
As there seem to be several BAs out there where the mail button doesn't work this might be a useful addition to the wiki.
However, I will not post it there without some feedback whether it works for others as well..
(I hope there aren't to many mistakes in the text; I am not a native speaker)
Final Note:
This is not my work, all the steps described above were found on this forum and on the wiki pages. I just did the job of combining them in a way that worked for me.
My biggest thanks to:
- crabiorc
- ramram
- sp3dev
- all the people who contributed to the wiki pages
Best wishes,
Dipak
is it ok downgrade from wm6.5 to wm6.1?
blueangelkoe said:
is it ok downgrade from wm6.5 to wm6.1?
Click to expand...
Click to collapse
Yes. If you feel more comfortable on a specific ROM it is always ok to downgrade or upgrade.
Upgrade XDA IIs to WM6.5
My XDA IIs just froze when resetted earlier and it was running on WM6.1 so I started to wonder if it had totally died. As I mainly leave it in the car and use it for satnav I was considering now buying a tomtom.
Then thought if its dead trying to revive it cant hurt so I found the following link (http://pinoytopdownloads.blogspot.com) to download a zipped file claiming to be WM6.5.
Opened the file and did a hard reset on devicethen sync with PC. Ran the programe which looked farmiliar from previous updates I had used so thought it might work. Half hour later, my XDA IIs came back to life running WM6.5 and none of my data such as text and contacts were lost at all.
It lives again.
Waiting for the HTC Touch Pro2 to see if it lives up to its hype and then can use my PDA as a phone again too cos lets face it... the XDA IIs is a bit of a lump now!
http://pinoytopdownloads.blogspot.com
Nice to hear that your BA is kicking again
Billy B said:
My XDA IIs just froze when resetted earlier and it was running on WM6.1 so I started to wonder if it had totally died. As I mainly leave it in the car and use it for satnav I was considering now buying a tomtom.
Then thought if its dead trying to revive it cant hurt so I found the following link (http://pinoytopdownloads.blogspot.com) to download a zipped file claiming to be WM6.5.
Opened the file and did a hard reset on devicethen sync with PC. Ran the programe which looked farmiliar from previous updates I had used so thought it might work. Half hour later, my XDA IIs came back to life running WM6.5 and none of my data such as text and contacts were lost at all.
It lives again.
Waiting for the HTC Touch Pro2 to see if it lives up to its hype and then can use my PDA as a phone again too cos lets face it... the XDA IIs is a bit of a lump now!
http://pinoytopdownloads.blogspot.com
Click to expand...
Click to collapse
Billy B:
I just bought an 02 XDA IIs. I love it but the bluetooth doesn't work with my Motorola S9 stereo headset unless it's 6 inches from my head. Does your XDA IIs work with stereo bluetooth? Have you tried it with WM6.1? I'd like to know.
Upgrading to WM6.1, Etc.
For all you upgrading Blue Angels to WM6 and high, you need to read the Wiki http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel. Read Blue Angel for beginners and also the upgrading to WM5 and WM6. You'll learn that you can free up some memory being used for the Extended ROM among other things.
I am new here, and this is my first rom flash. I have an O2 XDA lls that was given to me by a friend on WM2003. On XP, following the instructions on the wiki, I have tried with several roms. The flash seems to work, but then as soon as I reset the phone I am back in WM2003. Instead of a striped boot screen, I simply see an O2 logo, and when using the key combinations, I get no debug options.
Anyone have any ideas?
well did you flash a proper rom or maybe just a radio rom, meaning just an upgrade on wireless tech, because that process would "feel" like flashing a rom but actually doesn't change the OS
I don't really know. But I used the roms on this page:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
if that helps. I also used one off the helmi_c to check it wasn't a dodgy rom. DO you have any specific one to recommend? When I downloaded and unziped the rar, I simply ran the upgrade file within which started a wizard which said it would upgrade my pda. Strangely, the wizard did not display any information about the pda on the screen which tells you the rom info. Is it possible that it is not being detected? Do I need to install some extra drivers on XP?
it is perfectly normal that this upgrade tool does not show all the information like an official upgrade would, first of all, that is because these are cooked roms, meaning you only upgrade the OS, not the protocol, radio and extrom. that would be baked roms. but anyway, also, that the device's current information is not fully shown or not shown at all is normal, as you are probably using the MAupgradeut_noID.exe in contrast to the original BAupgradeut.exe, just by the first two letters (and the giant picture in the wizard) you can tell that this upgrade tool is actually for the magician, but works best for BA.
for recommendation:
http://forum.xda-developers.com/showthread.php?t=482997
the R6.1 release on that site is the newest real release, meaning you can get full further support, the download links work...
Don't get fooled by the R6.1, we are still talking about wm6.5, it is just the xplode release number.
P.S. no extra drivers needed, just use the wiki wizard word by word and it will work
The same thing happens again. Using the ROM upgrade file, it all seemed to work, and then when I attempt to do a hard reset, I get no stripes, just an O2 logo, and no boot options. I am then returned to Wm2003. Maybe I will try on another computer.
it's nice, but there is some application lost.
i've upgrade my xda 2s to WM6 cooked by HELMI, i download from http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4_Vista and look powerfull, its nice, but there is some application lost that i need. there is'nt auto config and xBackup...some one can help me to get that application??....thank's.....

Ugent help wanted

i've got a qtek 2020i
but something went wrong with an upgrade downloaded from qtek netherlands.
now i can't turn it on it doesn't work anymore
in teh screen i can read
serial
v1.01
or when in the cradle usb
plz help out here i can't fint it with active sync.
inreally need the damn thing. it's like losing my right hand
it came with winmobile 2003 ce
maybe i need a more resent version.
I am not an expert by any means but the fact that it switches to USB when cradled means it should be reflashable with a new ROM, search the o2.ie site for their most recent ROM. Not saying their offering is the most recent but it should get you going again
i searched but i can't find anything.
i don't know were i can find it
and if i do how does it work?
my telephone is using Orange / T mobile
Ok I had the same problem recently and managed to fix it using mtty.exe, and a working flash file.
The procedure goes like this:
Get mtty.exe, ( I found a copy on a file sharing site using google ).
Open Activesync and disable the USB option in connection settings, you'll need the usb port for mtty.
Put the device in the cradle, and check that it says USB , (it may say serial 1.01 at this point, don't worry, this happened on mine).
Run mtty.exe, and select USB, this will open a terminal window allowing you to communicate with the device. If you don't see USB as an option then exit mtty and try plugging the USB cable into another port.
Once you have the terminal window open, type task 28 and press enter, this will format the DiskOnChip.
Once this is complete and there are no errors, exit mtty, and run the upgrade, this should hopeully restore your Alpine.

Upgrade to Windows Mobile 6.x

Dear XDA Members,
I have now read the official Wiki five times, and I still haven't understood how to upgrade my BA to a Windows Mobile 6.
The Wiki "HTC Blueangel WM6 Home" links to a Wizard Style Wiki for this, however that link only returns a 404 Error. I also haven't found any information about this in the FAQ or orther threads. Maybe it's just me?
Where can I find a WM6 image for the BA (T Mobile MDA III)?
What software do I need to flash it via USB to the BA?
Thank you in advance.
Chris
Please refer to http://forum.xda-developers.com/showthread.php?t=630416
The instructions are there in Posts 1-6. Good luck.
Sunny
hi and welcome to the forum
as stated by sunny, my tutorial thread should cover all aspects of the upgrade process, including links to most of the recent roms.
the blueangel wiki suffered from the transfer to the new mediawiki project, which is why it should not be used for tutorials anymore.
Thank you both for your fast and helpful support.
I am running a non-english Windows Mobile 2003SE (GER) and executed the steps from your Guide to downgrade it to a WWE version. On xplode.tk I downloaded the latest T-Mobile UK Version and extracted the files mentioned in step 1b from the Temp folder while executing the .exe file. I also copied the files into the RUU folder.
When I open the task manager in step 6 i can only find and kill "wcescomm.exe"; "WCSEMgr.exe" isn't there. I am running WinXP SP3, logged in as administrator.
When I start Maupgradeut_noid anyway, I doesn't show me the rom versions.
Where am I going wrong?
Edit: I forgot to mention I have read the thread "Cant' Downgrade from Win2003 SE GER to ENG", but renaming the folder and then trying it didn't work for me either.
if you can't see those processes, you are probably not running activesync. install the latest version (a link can also be found in that thread in the 2nd post) and create a temporary partnership. just connect the device in normal running mode and set it to sync something small, like notes or favorites, after syncing go to the connection settings and untick "allow usb connections" then you should be fine and you can continue with the next step, connect in bootloader mode, make sure the display changes from serial to usb. at that point, a new driver will be installed and then running the ruu should get the upgrade process working, meaning, then there will be numbers in the 2nd window. if not, please post the RUU.log found in C:\
I have already installed ActiveSync 4.5.0.
I created a temporary partnership syncing favourites and after that unticked USB syncing in ActiveSync.
Then I connected in bootloader mode, making sure the display changed to USB V2.07. No new driver was installed, but I guess that already happened in my earlier attempts.
The HTCRUU.log (no RUU.log there) i found on C:\ contained a "Image Radio Checksum Error", so I downloaded another image from another mirror, but got the same problem.
Here is the log from the 2nd attempt:
11:50:02:843 [msg] : Config Info : [000000],[0],[0].
11:50:02:875 [err] : Image Radio Checksum Error.
11:50:02:875 [msg] : Update Image. CE : [0], MSystem : [0], Radio : [0]
____
I HAVE however been able to flash a WindowsMobile 6.5.3beta image to the device without formatting, so thank you for helping me with that!
I reverted back to Win2003SE, because I would still like to get the 60MB if possible.
ah, ok, apparently the radio rom is damaged and shows a crc error, since you are planning on downgrading and then upgrading, just delete the radio_.nbf from your update folder and try again.
no worries, obviously, you did nothing wrong, but there have been a lot of corrupted radio roms around lately, xplode's rom archive has them and so mine and d-two's have them as well.
in general, a first indicator for corrupted roms is the file size, a nk.nbf rom must always have 32,769kb (1kb more than 32mb) and a radio has 4,097kb (1kb more than 4mb)
you can ignore (delete) all radio roms in the process of upgrading, frankly, it has nothing to do with the operating system itself, it is just the bridge between the operating system and the hardware. if you are not running radio 1.15.00 yet, which is the latest and according to most users, the best version, you can upgrade it any time you want, so i'd suggest: try and upgrade to wm6.x first and then, when you got used to flashing, flash the radio, or, if you are satisfied with your phone's in-call sound quality, bluetooth and wi-fi performance, don't flash it at all.
Ah, ok.
I deleted the radio file and tried again. This time it showed me an ms_.nbf Checksum Error. I deleted that one as well and got this:
09:51:05:968 [msg] : Config Info : [000000],[0],[0].
09:51:05:968 [msg] : RadioFile Not Exist !
09:51:05:968 [msg] : MSystemFile Not Exist !
09:51:06:171 [err] : Image CE Checksum Error.
09:51:06:171 [msg] : Update Image. CE : [0], MSystem : [0], Radio : [0]
I also redownloaded the MaUpgradeUt_noID.exe right from your signature to ensure I didn't use an old one. Still the same problem.
My radio file DOES have 4,097kb; the nk.nbf has 32,769kb as well...I have to admit i'm still puzzled.
I also downloaded the two most recent radio files from your tutorial thread. Same problem: Checksum error. But I do not get a checksum error when I try to flash one of d-twos os-images.
i'm changing the radio roms, i will only provide radio 1.15.00 from now on, and i will post the entire package, as it came from htc (including the original RUU).
Thanks.
Where can I find them? Your tutorial thread seems untouched.
flash
hi WeissenbornC,
are you flashing with vista or win7??
if yes read please d-two´s tut for flashing with vista/win7.
http://forum.xda-developers.com/showthread.php?t=622768
hope it helps
cheers scudo
Hi scudo2709,
I am using Windows XP. Flashing a ROM is no problem, I have now had 5 different ROMs on my BA. However, I haven't been able to flash a shipped english rom (WM2003) in order to format the flash drive. I keep getting Checksum Errors with all of the ones I've been able to try so far.
Thank you for trying anyway.

Categories

Resources