I try to install patch v2 of mamaich and after i select bootloader mode and try to flash the rom at 44% the update is finished and the phone write update completed but i reboot it and the phone not start up, i try to remake bootloader mode and reflesh wm5 first patch but after the phone go in bootloader mode and write USB the flash not start.
PLEASEEEEEEEEEEEEEEEEEEEEE HELPPPPPPPPPPPPPPPPPPP MEEEEEEEEEEEE
Qtek9090
Downgrade to WM2003
not work
I try to reinstall wm2003 se
Radio flash Work
Ext Rom flash work
when come the next phases (flashing CE ROM) the phone go dark and anything else appear on it.
If i take it from the craddle the phone return in bootloader mode!!!
Have other solution????
Well, prepare yourself to give your PDA a decent burrial service.
You can allways use it as a paperweight.
Just kidding.
Instead od upgrading the device the standar way try this:
Step 1. Enter Bootloader Mode [Power + Camera + Soft Reset]
Step 2. Upgrade it to WM2005 [Mamaic Patch 3]
Step 3. Hard Reset
Step 4. Enter Pre OS mode [Power + Camera + Record + Soft Reset]
Step 5. Disable debuging mode [needed]
Step 6. When the PDA swiches from Striped Scren + Version Numbers, Hard Reset it again.
Step 7. Let it boot in nomal mode.
The best of luck to you. Actually this is the kind of problem that really freaks people out... The idea of an USD 1000.00 paperweight is quite scary.
Related
Hi everybody
i use a
Orange SPV 3000 cid/sim unlocked
WM 6 NBD 7.3
IPL / SPL 2.26
GSM 02.25.11
OS 5.2.1413 (Build 17913.0.3.0)
Now i tried to go back to the latest German ROM Update provided by ORANGE CH.
(RUU_Prodigy_21611_2161111_010410_OR_CH_GER_Ship.exe)
The Update Process start's on the PC Screen and remains on 0% and will terminate with ERROR [260]: UPDATE ERROR
The Phone hangs and cannot enter in "3 color update mode".
I have to take out and reinsert the battery to bring the Wizard back to Work.
Then the Wizard start's up and you can work without any Problems. (Exept you have to set the Date / Time again it is set to 2006-02-14 12:00)
Next Steps
- did a Reboot on the PC and the Wizard -> Same Result
- tried to Flash NBD 7.3 ROM again -> Same Result
- did a Hard Reset (press the 3 Buttons on Reset then Send Button ) and tried to Flash again -> Same Result
- tried to manualy enter Update mode (press Camera Button on Reset) with the same Result the "3 color update mode" will not appear
Has anybody a Idea what else i can do?
Tnx in advance for any HELP
when manually entering bootloader mode are still holding the camera button in after the reset button is released? I usually hold for about 5 seconds after the reset button is released. im sorry if that don't work for you. never heard of anyone having trouble not getting into bootloader before.
mdajunkie said:
when manually entering bootloader mode are still holding the camera button in after the reset button is released? I usually hold for about 5 seconds after the reset button is released. im sorry if that don't work for you. never heard of anyone having trouble not getting into bootloader before.
Click to expand...
Click to collapse
dear mdajunkie
now i can enter bootloader mode manually
looks like i did not hold the camera button long enough before
thank you very mutch for your HELP
I assume the Problem is locatet on the PC and have to find out why i can't flash my Device again.
Recently i changed something on the PC - I installed a external BlueTooth-Dongle from MSI including the MSI BlueTooth Software
Starting now with the easyest step - reinstalling Active Sync 4.5 and try again.
Regards
Now everything works fine
I tried to Flash a ROM and it work's
i did not change anything exept entering the bootloader mode manually once.(no reinstall activesync or deinstall bt software !)
May be entering the Bootloader Mode manualy "cured" my PDA?
i don't know
Regard's
im glad you got it to work. Most important thing is to read make sure you know how to and are confident enough flash roms. Makes things a whole lot easier. Atleast that way if something goes wrong you will be able to backtrack a lot easier and maybe explain your situation a whole lot better. Hope everything else goes wonderful for you and have fun man.
Hi all,
what can i do?
You sure that what you're trying to perform is a hard reset, not a mere soft-reset?
If yes, this is really weird. Try flashing your ROM again.
jasczj said:
Hi all,
what can i do?
Click to expand...
Click to collapse
If you are trying to perform a hard reset and it doesn't work and phone won't reboot, then only other option you have left is to put phone in bootloader and flash stock/cooked rom.
Does phone reboot ok? Are you actually performing a hard reset i.e. turn phone off. Hold down vol up & vol down and then phone on while still holding down vol buttons. You will then be presented with a white screen with text asking you to press vol up once again to restore factory settings.
Fallen Spartan said:
If you are trying to perform a hard reset and it doesn't work and phone won't reboot, then only other option you have left is to put phone in bootloader and flash stock/cooked rom.
Does phone reboot ok? Are you actually performing a hard reset i.e. turn phone off. Hold down vol up & vol down and then phone on while still holding down vol buttons. You will then be presented with a white screen with text asking you to press vol up once again to restore factory settings.
Click to expand...
Click to collapse
yes ..colourful screen appear and after reboot still didnt help..phone wun sync so how can i flash my rom?
what is boot looder?
can someone gave me a step by step dummy guide?
thanks in advance
jasczj said:
yes ..colourful screen appear and after reboot still didnt help..phone wun sync so how can i flash my rom?
what is boot looder?
can someone gave me a step by step dummy guide?
thanks in advance
Click to expand...
Click to collapse
Have you tried a Hard reset?
As Fallen Spartan wrote : Are you actually performing a hard reset i.e. turn phone off. Hold down vol up & vol down and then phone on while still holding down vol buttons. You will then be presented with a white screen with text asking you to press vol up once again to restore factory settings.
If it doesn't help try to flash a cooked or stock rom but I recommend you to first try the hard reset.
jasczj said:
yes ..colourful screen appear and after reboot still didnt help..phone wun sync so how can i flash my rom?
what is boot looder?
can someone gave me a step by step dummy guide?
thanks in advance
Click to expand...
Click to collapse
Bootloader is the tri-coloured screen you are getting
If you can get phone in bootloader then you can still flash new rom.
First of all try a hard reset by doing the following:
1. Turn phone off
2. Hold down vol up & vol down
3. Continue to do No.2 and turn phone on
4. You will then be presented with a white screen with text asking you to press vol up once again to restore factory settings.
Once complete if phone still doesn't reboot you will need to flash new rom by doing the following:
1. Turn phone off
2. Hold vol down button only
3. Continue to do No.2 and turn phone on
4. You will be presented with bootloader screen (tri-colour screen)
5. Connect phone to pc and bottom of screen text should change from 'serial' to 'USB'. If this doesn't read cRaCKwHoRe's guide (see link below) as you may need to update pc drivers.
6. Now flash original stock rom from which you have downloaded from wiki. You can find stock roms here. To flash rom you will need to run ruu file from pc (this is rom you have downloaded)
Make sure you only flash original stock rom which was already on your phone. If you want to flash other roms you will need to follow cRaCKwHoRe's guide
I'd recommend reading the wiki so you understand more about the process and you phone
Good luck and keep us informed
Flasehed this ROM: 23563 V2 FULL WWE-ITA using Jump SPL 1.93 which went fine but later after installing the apps asked to reboot.
Once clicked on the reboot unable to get the phone back.
Does anyone have any ides on this. on how we can recover this. Or Flash another ROM from this state.
Moved as not ROM Dev.
By unable to put back on i imagine you can't power on device? Remove battery and try after an hour or so.
If not then maybe the end of the road.
kkp said:
Flasehed this ROM: 23563 V2 FULL WWE-ITA using Jump SPL 1.93 which went fine but later after installing the apps asked to reboot.
Once clicked on the reboot unable to get the phone back.
Does anyone have any ides on this. on how we can recover this. Or Flash another ROM from this state.
Click to expand...
Click to collapse
why did you use jumpSPL to flash a complete ROM???????????
its written everywhere that jumpSPL is only meant to flash HardSPL...and HardSPL is needed before you can flash any ROM. i mean why???????!!!!!
follow the advice the chef gave you in the thread for the ROM because i noticed you posted your question there as well in addition to starting a new thread here.
Try flashing Stock rom via 2GB or smaller SD Card. Check the wiki for Stock OEM Roms from your BRANDED Device.
mskip said:
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Kaiser Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to KAISIMG.nbh
4. Copy the KAISIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
7. You will first see a tri-color screen with the phone and SPL Information at the top
8. A message will then pop up asking you to press the Power button to start the update
9. Press power button to start flashing
10. Once phone finishes flashing and says Update Complete, reset with the stylus
11. When it gets to the screen where it configures the stylus, HARD RESET
(press left and right softkey buttons on the front and hold in reset with stylus until message appears)
12. When prompted, Press "Send Button" (Green Call Button on Front) to Clear Data
13. When prompted, Press "Send Button" (Green Call Button on Front) to Restart Phone
14. Follow onscreen instructions to set up your New Rom
Click to expand...
Click to collapse
Flashing Your First Kaiser Rom (For Noobs)
Guys,
Thanks for your advise, i have recovered my phone, i went into boot loader screen then flashed the original HTC ROM which is "TyTN II_AUS Hutch_WM6.1_Upgrade_20080602" which went through fine and ALL IZ WELL so far...
The reason i used the Jump SPL is that when i flashed normally, i was not able to get the ROM upgrade, it was throwing error message UPDATE error...
so
1. checked some info and Ran Jump SPL 1.93
2. Right click on the Active Sync then unchecked the USB connection
3. Connected back and ran the KaiserCustomRUU.exe
which went fine but anyhow learn lesson...
Thanks once again for everyone...
Hi,
Cannot boot to recovery console. Gets no image error. I have diamond 2 with wm6.5 installed. Please help
maildeeps4 said:
Hi,
Cannot boot to recovery console. Gets no image error. I have diamond 2 with wm6.5 installed. Please help
Click to expand...
Click to collapse
Ok what are you doing to try to boot your phone ? and what ROM are you using to boot with ?
If you only need to do a factory setting boot ie you want the ROM you already have on but restored back to how it was - follow this
1. Turn off the phone .
2. Hold vol + & - keys and tap power on button
3. Once on the Tricolor screen release the volume buttons
4. White screen will show follow the instructions on screen to reboot phone.
Your phone will now hard reset back to factory settings.
If you are trying to boot a new ROM over the top
1. Ensure you have Hard_SPL on your device details of this can be found below.
2. Attach the phone to the pc
3. Transfer over your .nbh ROM file to the root of the memory card
4. Once the image is on the card rename it to TOPAIMG.NBH
5. Follow the flashing how to guide here http://forum.xda-developers.com/showthread.php?t=585201 to flash your phone
If all else fails download a stock ROM from htc and re-flash original ROM.
hi there
I have problem with my phone
want to flash a custom rom on it and nothing knew about Ome lock and frp lock
wipe my phone with factory reset and now cant boot my phone because it need my google account and I forgot that my id Even cant flash custom recovery!
please help me I need my phone
On YouTube there should be a tutorial to help you, sure you find it because you only have to do a bypass.
If it says with red letters on top of the screen "FRP Lock" or something like that.
DONT BE AFRAID, i had that once and i almost thought my phone got bricked.
Steps:- 1) Press Power and Volume Down together
2) When it turns off, quickly press Volume Down, Home Button & Power together
3) It should go to download mode/odin mode
4) Go to updato.com, download your model firmware and odin
5) Flash it via odin (Put the firmware in AP) (Odin will freeze for a couple of min)
6) Start and wait
7) Done, you have a brand new phone (could possibly wipe data)
Atleast, thats what i did