how to recover from the flashed ROM, unable to reboot orstart - Tilt, TyTN II, MDA Vario III General

Flasehed this ROM: 23563 V2 FULL WWE-ITA using Jump SPL 1.93 which went fine but later after installing the apps asked to reboot.
Once clicked on the reboot unable to get the phone back.
Does anyone have any ides on this. on how we can recover this. Or Flash another ROM from this state.

Moved as not ROM Dev.
By unable to put back on i imagine you can't power on device? Remove battery and try after an hour or so.
If not then maybe the end of the road.

kkp said:
Flasehed this ROM: 23563 V2 FULL WWE-ITA using Jump SPL 1.93 which went fine but later after installing the apps asked to reboot.
Once clicked on the reboot unable to get the phone back.
Does anyone have any ides on this. on how we can recover this. Or Flash another ROM from this state.
Click to expand...
Click to collapse
why did you use jumpSPL to flash a complete ROM???????????
its written everywhere that jumpSPL is only meant to flash HardSPL...and HardSPL is needed before you can flash any ROM. i mean why???????!!!!!
follow the advice the chef gave you in the thread for the ROM because i noticed you posted your question there as well in addition to starting a new thread here.

Try flashing Stock rom via 2GB or smaller SD Card. Check the wiki for Stock OEM Roms from your BRANDED Device.
mskip said:
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Kaiser Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to KAISIMG.nbh
4. Copy the KAISIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
7. You will first see a tri-color screen with the phone and SPL Information at the top
8. A message will then pop up asking you to press the Power button to start the update
9. Press power button to start flashing
10. Once phone finishes flashing and says Update Complete, reset with the stylus
11. When it gets to the screen where it configures the stylus, HARD RESET
(press left and right softkey buttons on the front and hold in reset with stylus until message appears)
12. When prompted, Press "Send Button" (Green Call Button on Front) to Clear Data
13. When prompted, Press "Send Button" (Green Call Button on Front) to Restart Phone
14. Follow onscreen instructions to set up your New Rom
Click to expand...
Click to collapse
Flashing Your First Kaiser Rom (For Noobs)

Guys,
Thanks for your advise, i have recovered my phone, i went into boot loader screen then flashed the original HTC ROM which is "TyTN II_AUS Hutch_WM6.1_Upgrade_20080602" which went through fine and ALL IZ WELL so far...
The reason i used the Jump SPL is that when i flashed normally, i was not able to get the ROM upgrade, it was throwing error message UPDATE error...
so
1. checked some info and Ran Jump SPL 1.93
2. Right click on the Active Sync then unchecked the USB connection
3. Connected back and ran the KaiserCustomRUU.exe
which went fine but anyhow learn lesson...
Thanks once again for everyone...

Related

Urgently Help with flashing!!!

Please,help me as soon as possible -about get out a boot mode.
Situation-i was trying to flash one of Radios from that tread (as always),my Xperia is Hard-Spl,i was renamed downloaded file to Kovsimg.nbh, copy that to the root of MicroSD card,then turn Xperia in bootload mode (4 color bars) (you know-vol. button and on simultan),the file was recognized,i got the message (as always) "press power button to flash ROM or action button to cancel",i pressed power button, flashing begann and was already on 100%, but then was coming an Error message-"Flash not complete and some about RSA too".I take akku out and put in again,and now-don't matte how i turn Xperia ON,it always go to Bootload mode and want to flash that file (and it will not flashed).How i can get out now of that bootload mode???????I read "press Action button to cancel flashing",but what is that Action Button???And if i even take out MicroSD,Xperia start always in bootload and want to flash something!!!!I sit down in Hotel now,i don't have a MicroSD cardreader to copy on MicroSD another file,and i can't use my telephone,because it start always in that 4 color bootload mode and want to flash something!!!
Ple-e-e-a-a-se Help!!!! I don't want to hard reset my telephone now,i just want to start Xperia in normal mode.
Many many thanks in advance,
Valery
P.S.Sorry for my English-it's not good and now especially i'm totally nervous with that problem...
Action button is the middle of the optical joypad.
to reflash connect from your computer with a USB cable and use the Custom Radio RUU
AND DO NOT GO AROUND FLASHING THINGS UNLESS YOU KNOW WHAT YOU ARE DOING!
Thanks a lot for fast response!!!
I was flashing one of the Radio ROMs here in the thread,that was in the list as worked, maybe it was transfer failure to MicroSD card,now it don't matter.
I power now Xperia on, then see that 4-color screen,then now i see kovsimg.nbh- RADIO and "Press power button to start update image" and "Press action button to cancel update image". If i press the middle of optical joystick-as you said-then it happens nothing-i see the same screen...What schould i do????
This is the "n" time I write this:
Remove and reinsert battery
Turn phone on
Now you are out of bootloader
Thank you Gtrab for answer,
but it is what i mean and what is strange-i remove battery,reinsert it,push only On button,and i'm again in boot mode....Very strange,yes???
ValVK said:
Thank you Gtrab for answer,
but it is what i mean and what is strange-i remove battery,reinsert it,push only On button,and i'm again in boot mode....Very strange,yes???
Click to expand...
Click to collapse
Strange for you, but well known phenomena: your flash didn't complete
You'll have to flash again from a PC or by copying a new radio file to your microSD card, or you can use "mtty"... sorry there's no other way but reaching a PC
I have notebook here,but i can't connect to my phone,because it start always in boot mode.Is here some method to connect to phone without Active synch in that bootloader mode???I understand now-i must copy right file on my MicroSD card,how i can do it wothout MicroSD Cardreader and only with a phone starting in boot mode???
Thank you,
Valery
ValVK said:
Is here some method to connect to phone without Active synch in that bootloader mode???I understand now-i must copy right file on my MicroSD card,how i can do it wothout MicroSD Cardreader and only with a phone starting in boot mode???
Click to expand...
Click to collapse
you can't access the sd-card without a Cardreader but you dont have to. In the 4-color screen you should see the text "USB" when you connect the phone to the pc (as far as I remember, when the device is not connected to the pc instad of "USB" the text is "SERIAL"). In that mode you can use the RUU to update your device.
Mastermarv,
thank you very much!!!I was worked for me-i was using RUU Radio utilities in bootloader mode and flashed orig. Radio ROM-now it all started OK and all work again!!!!!Uf-f-f,so one "abenteuer"...
Thank you all the people,those tried to help me in this situation,much appreciated your help!!!!
Now i can some relax...
Valery
ValVK said:
Please,help me as soon as possible -about get out a boot mode.
Situation-i was trying to flash one of Radios from that tread (as always),my Xperia is Hard-Spl,i was renamed downloaded file to Kovsimg.nbh, copy that to the root of MicroSD card,then turn Xperia in bootload mode (4 color bars) (you know-vol. button and on simultan),the file was recognized,i got the message (as always) "press power button to flash ROM or action button to cancel",i pressed power button, flashing begann and was already on 100%, but then was coming an Error message-"Flash not complete and some about RSA too".I take akku out and put in again,and now-don't matte how i turn Xperia ON,it always go to Bootload mode and want to flash that file (and it will not flashed).How i can get out now of that bootload mode???????I read "press Action button to cancel flashing",but what is that Action Button???And if i even take out MicroSD,Xperia start always in bootload and want to flash something!!!!I sit down in Hotel now,i don't have a MicroSD cardreader to copy on MicroSD another file,and i can't use my telephone,because it start always in that 4 color bootload mode and want to flash something!!!
Ple-e-e-a-a-se Help!!!! I don't want to hard reset my telephone now,i just want to start Xperia in normal mode.
Many many thanks in advance,
Valery
P.S.Sorry for my English-it's not good and now especially i'm totally nervous with that problem...
Click to expand...
Click to collapse
I have the same problem! i can't even connect it to my pc cuz it doesn't recognize the phone... it's been stuck at the white " KOVSIMG.nbh - OS - Update in progress...." screen for more than 10 mins now. but it's 100%. I tried hard & soft reset, taking out the battery, and powering it on again , but it still goes back to this screen. please help me... thanks in advance

Rom flash saying "loading..."

i'm trying to insall a new rom valkyrie v1.6... i've put it on my memory card root and changed it to kovsimg.nbh got the three colours, now all it says is "Loading..."
any ideas?
X1 rescue! Bricked?
I flashed stock SPL over HSPL before flashing back the stock ROM.
X1 will shows the SPL version following by "Loading..." on the LCD whenever power up! (with memory card inside the phone)
My SPL is 0.72.
The phone should be in recovery mode now without valid ROM/OS in it.
I copy an official UK ROM (R2AA010) into the micro SD card and rename it to kovsimg.nbh,
remove the battery for a few sec, insert the SD card with image file and then hold VOL Down button and power button to boot into Flash mode.
Press Power button to begin flashing process.
(Like normal flashing to other ROM after HSPL mod)
The phone should read the ROM image data and reflash back x1.
If this method not working, try to hold Power+VOL Down and press the RESET at the same time until the phone turn into "Rainbow" screen then try to flash again.
This "Rescue method" works for my set but I still advice that MUST flash stock ROM then only follow with SPL!
If your xperia is stuck in a "boot loop", which I think is what you're describing (as I remember mine always said it was loading the rom, each time you rebooted) then there's a PC application called mtty. it gives a command line interface to the phone when connected by USB.
I don't remember what commands are needed, but a search of the forums should find them. You need to set it to boot properly. Sorry I can't be more helpful, it was last year at some point that I needed this last.
ongbs said:
I flashed stock SPL over HSPL before flashing back the stock ROM.
X1 will shows the SPL version following by "Loading..." on the LCD whenever power up! (with memory card inside the phone)
My SPL is 0.72.
The phone should be in recovery mode now without valid ROM/OS in it.
I copy an official UK ROM (R2AA010) into the micro SD card and rename it to kovsimg.nbh,
remove the battery for a few sec, insert the SD card with image file and then hold VOL Down button and power button to boot into Flash mode.
Press Power button to begin flashing process.
(Like normal flashing to other ROM after HSPL mod)
The phone should read the ROM image data and reflash back x1.
If this method not working, try to hold Power+VOL Down and press the RESET at the same time until the phone turn into "Rainbow" screen then try to flash again.
This "Rescue method" works for my set but I still advice that MUST flash stock ROM then only follow with SPL!
Click to expand...
Click to collapse
I got the same problem too,, I try to use your " Rescue Method" , but the phone will turn off by itself when it is updating . I already try R2AA010 and R3Axxx....

Bricked (?) X1 rescue!

I flashed stock SPL over HSPL before flashing back the stock ROM
X1 will shows the SPL version following by "Loading..." on the LCD whenever power up! (with memory card inside the phone)
My SPL is 0.72.
The phone should be in recovery mode now without valid ROM/OS in it.
I copy an official UK ROM (R2AA010) into the micro SD card and rename it to kovsimg.nbh,
remove the battery for a few sec, insert the SD card with image file and then hold VOL Down button and power button to boot into Flash mode.
Press Power button to begin flashing process.
(Like normal flashing to other ROM after HSPL mod)
The phone should read the ROM image data and reflash back x1.
If this method not working, try to hold Power+VOL Down and press the RESET at the same time until the phone turn into "Rainbow" screen the try again.
This "Rescue method" works for my set but I still advice that MUST flash stock ROM then only follow with SPL!
i heard you are supposed to flash the stock rom THEN soft spl. not the way you did it
It is the rule: always restore last what you have flash first
james_2k said:
i heard you are supposed to flash the stock rom then soft spl. Not the way you did it
Click to expand...
Click to collapse
sometime bad things happen :)
Hope this info may help those screw-up their X1.
I believe those with bad flash may try to recover their X1 with this method.

help me cant enter bootloader

i am trying to use SEUS to update my rom, the problem is i cant enter the bootloader
i followed these instructions.
1. make sure battery power is 50% above
2. turn off x1
3. remove battery
4. return battery
5. hold volume down, then hold power
after that, my x1 boots normally, not in bootloader.
help please
dlegendkiller said:
i am trying to use SEUS to update my rom, the problem is i cant enter the bootloader
i followed these instructions.
1. make sure battery power is 50% above
2. turn off x1
3. remove battery
4. return battery
5. hold volume down, then hold power
after that, my x1 boots normally, not in bootloader.
help please
Click to expand...
Click to collapse
2. Make sure X1 is off
3.-4. You can skip this if X1 is really off
5. Press on the "down volume" (the button you press to decrease volume level) and DO NOT LET GO
6. WHILE STILL PRESSING the volume down key, press the power button AND DO NOT LET GO OF BOTH KEYS until the tricolor screen appears
it still doesnt work sir,
pinoy here
are there requirements in entering bootloader?
please help me, is it required to have my memory card formatted? and my phone is fresh (hard reset)?
If you just want to update your phone, you really don't need to use SEUS. Just flash the WWE R3A stock ROM (it's in the stickied thread in the ROMs section) using the RUU (activesync) method
harveydent said:
If you just want to update your phone, you really don't need to use SEUS. Just flash the WWE R3A stock ROM (it's in the stickied thread in the ROMs section) using the RUU (activesync) method
Click to expand...
Click to collapse
but in this case it think it's very important to say that it's only that simple if he want's to flash a stock-rom!!!
(meaning "an original rom by SE")
@dlegendkiller:
if you ever want to flash a custom-rom then first read about flashing hard-spl and then do it before flashing custom-roms. if not, you can get into serious trouble. (it's easy and save if you follow the instructions)
dlegendkiller said:
please help me, is it required to have my memory card formatted? and my phone is fresh (hard reset)?
Click to expand...
Click to collapse
honestly, i think you're either doing something wrong here OR your volume-button is broken. regardless of your sd-card you should be able to enter bootloader-mode (the tri-color screen).
are you really doing it this way? to test do it without the usb-cable attached:
- turn your phone off completely
- press your volume-down-button and keep pressing it
- now press the power-button and also keep pressing it
you'll know when to release the buttons yourself.
anyway, can i get some advantages in updating my rom? i really am scared to install custom roms, i might break the phone
and i want to install manila hd, i am wondering why i cant install it
its about "system permissions etc etc"
does it require custom rom?

[Q] Cannot boot to recovery Diamond 2

Hi,
Cannot boot to recovery console. Gets no image error. I have diamond 2 with wm6.5 installed. Please help
maildeeps4 said:
Hi,
Cannot boot to recovery console. Gets no image error. I have diamond 2 with wm6.5 installed. Please help
Click to expand...
Click to collapse
Ok what are you doing to try to boot your phone ? and what ROM are you using to boot with ?
If you only need to do a factory setting boot ie you want the ROM you already have on but restored back to how it was - follow this
1. Turn off the phone .
2. Hold vol + & - keys and tap power on button
3. Once on the Tricolor screen release the volume buttons
4. White screen will show follow the instructions on screen to reboot phone.
Your phone will now hard reset back to factory settings.
If you are trying to boot a new ROM over the top
1. Ensure you have Hard_SPL on your device details of this can be found below.
2. Attach the phone to the pc
3. Transfer over your .nbh ROM file to the root of the memory card
4. Once the image is on the card rename it to TOPAIMG.NBH
5. Follow the flashing how to guide here http://forum.xda-developers.com/showthread.php?t=585201 to flash your phone
If all else fails download a stock ROM from htc and re-flash original ROM.

Categories

Resources