BA Upgrade to WM5 if Mail H/W Buttong non functional - MDA III, XDA III, PDA2k, 9090 Software Upgrading

I have just gone throught the documentation on upgrading a BA (PDA2k) to WM5.
In describing part of the process, in the Section on Hardreset based on Screen Information, we are told, "If you are done, press the mail button, it'll show a white screen for a while, just wait." My concern is that the bottom row of Hardware buttons on my device no longer work, including of course the mail button.
If I were to try the upgrade what would I do at the time that i am required to press the mail buttom?
Is there some other action that achieve the same result or will I be stuck waiting for something that will never happen?
hinds

Are you saying they are physically broken? If that's the case I can't think of any other way for you to upgrade to WM5...

Well, they are physically there but I guess they are electronically broken. Oh well, I would have liked to give it a try but I suspected that it would not have been possible under the circumstances.

Related

Bricked, I need some input and advice.

OKay, so I have had My Tmo(USA) MDA (HTC wizard) forapproximately 13 days. Today while trying to transfer a ringtone from my old phone via bluetooth, my phone restarted and stalled during the booting. I soft-reset the device and the same thing happened, and again a third time. After which I decided to bite the bullet and do a hard-reset. After the reset the phone goes even less into the boot screen (the rainbow icon does not appear like it did before) then the screen goes dim and the device shuts off. I have called tech support at tmo to no avail, I have also tried going into bootloader mode with no response. the battery was at 60% when this started so i know this isn't a power issue.
any thoughts, input or help on this matter will be greatly appreciated.
my safegaurd is to exchange the phone tomorrow, but this is a last resort.
EXCHANGE IT! Dont wait till its too late. Just get a new one. You weren't even doing anything that would normally cause this type of result. You have nothing to loose by exchanging it, other than a little time, any data on the phone is gone anyways.
You sure you did a hard reset? I don't mean to be a jerk, and I'm not saying you don't know what your doing I am simply suggesting that you double check. Make sure you get to the black "press send to format storage, any other key to exit" and press "SEND" =)
Hope you get back up and running soon; Lew
Swap it. You weren't doing anything that could have led to YOU "bricking" it.

Pls Help: Problem with Power Button

From yesterday onwards i am getting this problem.power button is nt workn as previous.Phone automatically get the signal of long press power button.it means automatically it asks "power will be turned off,and you may lose data if...".and also when i press power button it doesnt goes to standby mode.when i long press the power button sometimes it doesnt switch off..As i think the power button dnt work as normal or may it seems that power button keep pressed internally..pls help me to solve this problem.thnx in advance
some1 pls help me
naheelja said:
some1 pls help me
Click to expand...
Click to collapse
I'd suggest you make a full backup and hard reset the device in order to make sure its not a hardware problem. If it works fine after a hard reset, you'll know its something you installed relatively recently.
I did a hard reset.nothing changed.then i flashed a different ROM.But still i am facing the problem.
Try the following:
Get a can of canned Air and blow it on the button as it might move any debris that are there. Just make sure that the phone is off and the battery is out. KEEP THE AIR STREAM AWAY FROM THE SCREEN! If any of the propellant escapes while you spray, it can freeze the LCD. Just slide it open and stick some paper on top of the screen. Wait a few moments before you switch the device back on
If this doesn't work, flash the Kaiser with its original ROM and SPL just in case there is an odd interaction somewhere. See here: http://forum.xda-developers.com/showthread.php?t=418375
If nothing of the above work, you have two options:
a. If the device is in warranty, return it and get it fixed or replaced. Make sure is has its original ROM/SPL loaded before you do.
b. If the device is out of warranty/you don't care about the warranty, you can try to open it up and see if something is blocking the switch. There are instructions floating around here somewhere.
EDIT: Added warning regarding the propelant and the LCD
Any update here? My tilt is doing the exact same thing
alt236 pretty much said all there was to it. Hard reset, restore stock ROM, try blowing the switch, if all fails send for repair.
Did all of the above and the cost of repair is not worth it. Time to toss my kaiser I guess

I Unbricked my 8125

Ok, I know not everyone will have a similar situation and maybe my post is quite late since many might have moved on to other nicer phones ;-)
I was uploading ROM using ShellTool that takes awfully long and my PC (an XP) decided to download updates and reboot all by itself. Needless to say, I was stuck at the boot screen with the IPL, SPL, GSM and the OS screen. The OS was showing 6.0.0.1 and that's it. pressing the Voice Dial and COMM button and resetting didn't help. So out of frustration, I pressed the Camera and Voice Dial buttons and did a reset and Presto, got the Red, Green, Blue with USB screen. I was able to load ATT's WM5 on it. Am sure many will like to know this minor pleasant mishap.
Hard Reset is mentioned here http://www.pocketpccentral.net/help/cingular/8125reset.htm
I would call my trick as the Hard Wiping
ak2k8 said:
Ok, I know not everyone will have a similar situation and maybe my post is quite late since many might have moved on to other nicer phones ;-)
I was uploading ROM using ShellTool that takes awfully long and my PC (an XP) decided to download updates and reboot all by itself. Needless to say, I was stuck at the boot screen with the IPL, SPL, GSM and the OS screen. The OS was showing 6.0.0.1 and that's it. pressing the Voice Dial and COMM button and resetting didn't help. So out of frustration, I pressed the Camera and Voice Dial buttons and did a reset and Presto, got the Red, Green, Blue with USB screen. I was able to load ATT's WM5 on it. Am sure many will like to know this minor pleasant mishap.
Hard Reset is mentioned here http://www.pocketpccentral.net/help/cingular/8125reset.htm
I would call my trick as the Hard Wiping
Click to expand...
Click to collapse
It's not a trick, it is called the RGB bootscreen.
not same as RGB, the actual boot.
well, all I got stuck was at the boot screen, not the RGB screen, the screen that just shows the IPL, SPL, GSM and OS numbers with the Cingular screen. I did not find anywhere that showed me to get out of the screen till I accidentally came across it. Actually, the record button is not necessary, just the camera button is fine while pressing the reset and holding it till the RGB screen is back.
Where did you get AT&T's WM5 rom, I am having the same problem. I have the IPL/SPL but can't find the rom, the link in the thread here no longer works.
Thanks.

Soft/Hard reset problem

Hi all,
I just migrated from Hermes to Tilt. I've upgraded to HardSPL 3.56 and installed the latest AT&T official rom for tilt. Everything seems to be working fine except for the soft reset or hard reset procedure.
In the manual it states to simply push the stylus in the reset button hole. For hard reset "hold down left and right soft keys and push stylus, then release stylus and wait till the confirmation msg appears then release soft keys, finally pressing send button for confirmation". None of these procedures work. I've tried it several times, but nothing happens, as if there is no button in the reset hole.
A friend of mine bought a tilt a few months back and he reports the same thing, though he is not the type who will play around with his phone so he doesn't bother with it. But to me this seems to be a big issue, I tried searching for this isue on AT&T forums but no succes. So now I ask here, is this a common issue with TILT? (I know HTC TytnII reset works fine). Is there a remedy for this problem? should I return it or should I just live with it ?
Thanks
Shoaibz said:
Hi all,
I just migrated from Hermes to Tilt. I've upgraded to HardSPL 3.56 and installed the latest AT&T official rom for tilt...
Thanks
Click to expand...
Click to collapse
assalam o alaikum shoaib:
no this is not a reported problem as the procedure is pretty striaght forward.
just simply insert stylus into the hole next to the chargin usb port on bottom of phone (not the small hole but the slightly bigger and round one on the top right side of charging port).
hard reset hold both soft keys and while holding them insert stylus into soft reset hole, maintain this position until you see the warning about hard reset and than proceed. Make sure you are not fat thumbing the keys i.e. not pressing two different keys (hitting the ie key while keeping the soft key pressed).
Hope this helps.
thesire said:
assalam o alaikum shoaib:
no this is not a reported problem as the procedure is pretty striaght forward.
just simply insert stylus into the hole next to the chargin usb port on bottom of phone (not the small hole but the slightly bigger and round one on the top right side of charging port).
Hope this helps.
Click to expand...
Click to collapse
walekum es salam thesire:
Well as i wrote in my initial post, I've tried the proper procedure, and believe me I was inserting in the right hole ! But nothing seems to happen. I can go into boot loader mode when the tilt is off by pressing the camera and power button, and releasing the power button while still holding the camera button but can't do anything with the reset button. Its working alright otherwise no hangups no nothing. Should I hold on to it or return it? btw Its secondhand not new !
Before you return it, is your stylus the original one? Maybe its an aftermarket stylus that is too fat to go in all the way. Try with a safety needle and see if that reaches it.
If not, i'd go ahead and return it, i've been through 4 kaisers and not had this issue.
fone_fanatic said:
Before you return it, is your stylus the original one? Maybe its an aftermarket stylus that is too fat to go in all the way. Try with a safety needle and see if that reaches it.
If not, i'd go ahead and return it, i've been through 4 kaisers and not had this issue.
Click to expand...
Click to collapse
Nope doesn't work. Stylus is small enough to go all the way in. I checked with a bright flash light and there is no black push button switch as all other devices have for a reset switch. Its all black plastic. Should I open the casing to check it ?

Weird Kaiser Hardware Button Failure

Hi all, please can you help me with this!?
Firstly when my phone boots or is taken out of sleep mode it immediately activates voice record as if this button has been pressed. It then opens the dialler and types ‘EDFC’. If I open pocket word and then wake the phone up it also types ‘EDFC’ before doing the above.
My keyboard is not working and the only hardware buttons that function are the power button (only for a while), the camera button and the silver select button in the middle of the d-pad. The jog wheel and silver directional d-pad buttons occasionally come to life. The others don’t work (green call and red end buttons, ok, windows etc).
When I use the standard keyboard SIP on the screen the directional buttons and delete do not function?!
I’ve reverted to a stock ROM to make sure this isn’t the problem.
It appears as though my Kaiser thinks these buttons are being depressed, but I’ve checked them and they click normally and release when pressed (even though they don’t perform a function) so nothing is stuck down etc….
I’m going to use AE Buttons to try and unhinge the button functions for now, but it would be great if someone has any suggestions!!
Thanks in advance.
Update - AE Button won't unhinge the buttons or change their function to anything else (e.g. nothing). I can't stop this from happening every time the phone boots/wakes up!
Help!
Mine got the same symptoms last week except it opens quick something or other,and then the dialler dials 2547.The screen for my pin then comes up,which I can enter normally.Home screen fires up normally but the keyboard will not work or any buttons except the silver one in the middle.Searched a bit and this problem is very common although I cannot find a solution anywhere.Can someone please help
AE button didn't work?
When mine did that, I reset all the hardware buttons (not the keyboard, just the buttons reachable from the outside. A soft reset and viola!
That's the only solution I have. It's worked for me 2x.
Also try pulling the battery for 20 seconds or so and restarting. That has fixed my touchscreen not working after it gets spashed 3x. Yeah, my phone is old and abused, but keeps working.
Will
wasilvers said:
"I reset all the hardware buttons (not the keyboard, just the buttons reachable from the outside. A soft reset and viola!"
Click to expand...
Click to collapse
Thanks for your replies - I've got Orange sending me another one in the morning now and sods law it's just stopped happening.... Taking the replacement anyway in case it happens again.
For my knowledge, how did you reset the buttons? I deleted some registry keys to completely stop them working (although I couldn't find the registry keys for the red and green buttons).
Searching on Google there are quite a few reports of this, but no one has ever posted the cause!
I am having the same problem... please help. My phone is going crazy. I did a hard reset but still didnt solve the problem....
I am also having this issue. Phone starts typing EDFC and then initiates the voice recorder. I reflashed various ROMs and regardless of what was flashed.. initially they appeared okay, then it started happening again. I also tried hard and soft resets. Nothng has worked so far.
I resorted to disabling the keys and some of the applications which I dont use which appear to be getting started/run (Voice recorder for one). So far I havent had the issue, knock on wood.
I think this is more than likely a hardware error. My tilt is actually pretty old so I wouldnt be surprised. If someone finds either the cause or a workable solution please post. Im trying to hold off until January when my contact expires to get a new HTC.
I searched and searched but found no solution for this and ended up getting the phone replaced.
HTC seemed to know nothing of such a problem....
Have you tried whacking it?!!?
Hope you get it sorted.
brandall said:
Have you tried whacking it?!!?....
Click to expand...
Click to collapse
Hmm, yes, but I don't see how that helped my phone.
lol, all jokes aside, my friends, I ask in this thread as well,
what is causing this problem? I ran into this issue after ALL my buttons stopped working (except for the power).
I installed a new rom (I forget which one), and still nothing works except for power button.
It would be even better if someone knows the solution!
-Calling for Help-I'm still convinced it is a software/registry problem...
Okay, so there's no solution available for this weird problem of ours.
On the bright side, however, it is amazing that we can still use the phone, even after it requires servicing (some way or another). I have accepted this handicap that has been placed on my phone for now, simply hoping it will grow out of it one day.
But something isn't right. When I looked in the registry (trying to follow some directions I found within the wiki for when your keyboard STILL doesn't work properly), there was a discrepancy between what was supposed to be found in the registry and what was actually there. It wasn't that the values were wrong, it was the names of the values that were different. Why could this be?
Or even if you have moment of time, and you have an AT&T Tilt, and it works perfectly, maybe you could write up a run down of what you have hanging around in that section of the registry?
Hey, just so I can be sure, is there some place I can cross check what I have in my HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP with what is supposed to be there in a fully functioning AT&T Tilt?

Categories

Resources