Tried to Upgrade rom --> Crashed --> Now DEAD!! HELP!! - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Please Help!!
I tried to use the aWizard utility and I did the RAPI and CID unlock and tried to install the 1.6.7.1 to my qtek with the original sept 22nd rom. It froze while doing the upgrade (after 3 or 4 mins) and now it gets stuck at the splash screen but it shows the 1.6.7.1. It does not connect via USB anymore and I can only soft reset or hard reset and it goes back to the qtek splash screen and hangs.
Do I have a paperweight?? Is there anything i can do without it being able to connect to USB??
Any help would be appreciated.
Riker.[/b]

Enter Bootloader, - hold the "camera" and shortly press the reset button, don't release "camera" until you can see color screen, connect USB cable, and start to flash any ROM you like from ftp...

Thanks for your help!! It worked perfectly!! I am a long time 'viewer' and have loved all the knowledge that is available on these forums!!
I hope this helps out anyone else who is in a similar situation and is scared they have destroyed their device.
Boy am I relieved!!!
Riker.

OK
Try this funny rom:
ftp://xda:[email protected]/Up...TOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe

Re: Tried to Upgrade rom --> Crashed --> Now DEAD!! HE
riker said:
Please Help!!
I tried to use the aWizard utility and I did the RAPI and CID unlock and tried to install the 1.6.7.1 to my qtek with the original sept 22nd rom. It froze while doing the upgrade (after 3 or 4 mins)
Riker.[/b]
Click to expand...
Click to collapse
Hi Riker,
The upgrade takes 10 to 20 minutes to complete. If you stop it before it say finish then.... u have to flash ur device all over using upgrade program.

Button said:
OK
Try this funny rom:
ftp://xda:[email protected]/Up...TOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Click to expand...
Click to collapse
Thats unfare!
I may try somethings, but i'm not installing a new rom, without at least knowing what its going to do? :lol:

CID-unlock your Wizard first, please.

hey man..your lucky u got urs to work straight away
im stuck exactly where u r but now when i upload the new rom...nothing happens still..think its because i didnt do cid unlock...but it did say CID is unlocked on your phone now....
well...i just cnt get wait to get this dead 9100 to be bk up again..

Related

Help Please ! Won't go past the Splash Screen?

I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John
I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?
I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!
Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!
this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP
PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S
Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse
stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse

Revive this bricked (?) Wizard!

I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Hi!
At the tri-color screen you should be able to flash it with a new ROM. Just try it, that worked for me after a failed flash.
Cheers
djvw
rockmanneo said:
I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Click to expand...
Click to collapse
I just had the same problem myself, talk about ****ting my pants.
I have a Dutch rom in my Vario and I cid unlocked it and tried installing
a US rom but the phone was dead after it.
In the tri-color screen I tried to load the new 2.26 US rom and then the latest UK rom but both failed with invalid Vendor id or something like that.
So I downloaded the NL rom from here and thnk god it loaded without a problem and the Vario is working again.
Sadly in Dutch but at least it works again, can anyone from Holland help me upgrade to the latest US rom ?.
Dave...
Dave...
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
rockmanneo said:
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
Click to expand...
Click to collapse
PC doesn't need to recgonize the device via activesync to flash the Rom.
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Regardless of your activesync status it should start updating your mda.
This takes about 10 minutes, and will pause at some stage, don't be alarmed and don't pull the plug !!!
Good luck
the-equinoxe said:
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Click to expand...
Click to collapse
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Regardless of your activesync status it should start updating your mda.
Click to expand...
Click to collapse
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Good luck
Click to expand...
Click to collapse
Thanks :wink:
rockmanneo said:
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Click to expand...
Click to collapse
It's recomended to go back to the original rom, so you can go back to the point before the problems began..
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Click to expand...
Click to collapse
In canary-screen mode the phone will have an active usb connection, ActiveSync won't detect it however, because the ActiveSync software on the phone is only started when windows-mobile is running (which doesn't occur in boot-loader).
The Rom Upgrade Utility, should be able to detect the phone.
But always make shure the battery has been charged (at least half-charged).
Several people on this forum have revived their semi-bricked phone this way.
Thanks :wink:
Click to expand...
Click to collapse
You're welcome

Slowww wizard unable to sync

Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
i'm glad i solved the problem.. just entered manually in bootloader then flashed a original qtek rom and it fine now
thanks anyway, hope this help other people in this very situation
bye
cheers from portugal
W4R_M4ST3R said:
Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
Click to expand...
Click to collapse
You can't go from 1 to 3. Re-flashing a stock ROM was a good move.
--M
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
zorrozorro said:
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
Click to expand...
Click to collapse
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
_Nomad_ said:
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
Click to expand...
Click to collapse
How can i upgrade my ROM if i could not connect my phone to the computer! The main problem is that i could not syncronise my phone and my PC.
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
_Nomad_ said:
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
Click to expand...
Click to collapse
Thank you!!
Could you explane me a bit more precise what does it mean bootloader and reflash? Does it mean that i can syncronise phone and computer when i have RGB on my screen?
When you've got your device in bootloader mode just plug it in and start the upgrading procedure
_Nomad_, thank you!
It works now!!
zorrozorro said:
It works now!!
Click to expand...
Click to collapse
Like music to my ears

Phone locked in bootleader!! Cannot even Hard Reset!!

Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...

TYTNII radio

Hello,
I have a tytnII orange france radio 1.27.14.32.
I update my rom to MyPPC_MLs_K3.1_0816.zip using jump_1_56 because I can't update without it.
So the phone started normaly but the sound, camera not ok.
So I read that I must update also the radio. I downloaded the Kaiser_Radio_1.71.09.01 from http://webftp.myppc.it/index.php?dir=Kaiser/Radio/
I have found two methods :
the first is http://forum.xda-developers.com/showthread.php?t=393182
I tried it but when the phone is in the bootloader screen, he disappear and make a white page with a blue 'loading...' in the top,
I wait for 10 minutes and nothink ...
So I stopped the procedure, and the phone retart normaly with no problem.
I tried twice, the same problem.
So I start the second method, using the KAISERCustomRUU.exe, and of course jump_1_56 to get the bootloader screen with jump, so the procedure start with no problem until 99% ................. and here .............. ERROR ...
And now when I try to start my mobile phone, I have only t he bottloader screen with my old radio and STOPPPPPP.
In this point I try another time the first procedure with the sd card and radio 1.27.15.32 and nothing ...
NEED HELP PLEASE
original spl 1.81.000
try get a hammer and gently hit it as hard as you can for a couple times. here it is! you got a new radio version. i did this with my kaiser because i do not understand why i was so naive when i bought this piece of s#it!
thehou said:
Hello,
I have a tytnII orange france radio 1.27.14.32.
I update my rom to MyPPC_MLs_K3.1_0816.zip using jump_1_56 because I can't update without it.
So the phone started normaly but the sound, camera not ok.
So I read that I must update also the radio. I downloaded the Kaiser_Radio_1.71.09.01 from http://webftp.myppc.it/index.php?dir=Kaiser/Radio/
I have found two methods :
the first is http://forum.xda-developers.com/showthread.php?t=393182
I tried it but when the phone is in the bootloader screen, he disappear and make a white page with a blue 'loading...' in the top,
I wait for 10 minutes and nothink ...
So I stopped the procedure, and the phone retart normaly with no problem.
I tried twice, the same problem.
So I start the second method, using the KAISERCustomRUU.exe, and of course jump_1_56 to get the bootloader screen with jump, so the procedure start with no problem until 99% ................. and here .............. ERROR ...
And now when I try to start my mobile phone, I have only t he bottloader screen with my old radio and STOPPPPPP.
In this point I try another time the first procedure with the sd card and radio 1.27.15.32 and nothing ...
NEED HELP PLEASE
original spl 1.81.000
Click to expand...
Click to collapse
should make sure you Kaiser is "application unlocked", run SDA_ApplicationUnlock installed on your PC then copy sspl 1.56.exe to your device and run it !!!! to solve the problem on the device you must try hard reset at device (Hold Both soft keys in while pushing in Reset button :When prompted push Green Talk Button to clear data )
lexpet said:
try get a hammer and gently hit it as hard as you can for a couple times. here it is! you got a new radio version. i did this with my kaiser because i do not understand why i was so naive when i bought this piece of s#it!
Click to expand...
Click to collapse
Hei dude , you really crazy lexpet <<<< Crzy
Hakim Rahman said:
should make sure you Kaiser is "application unlocked", run SDA_ApplicationUnlock installed on your PC then copy sspl 1.56.exe to your device and run it !!!! to solve the problem on the device you must try hard reset at device (Hold Both soft keys in while pushing in Reset button :When prompted push Green Talk Button to clear data )
Click to expand...
Click to collapse
yow bro dont worry here is a thread that will set set you right its everything about radio that just helped me : http://forum.xda-developers.com/showthread.php?t=393182
thehou said:
Hello,
I have a tytnII orange france radio 1.27.14.32.
I update my rom to MyPPC_MLs_K3.1_0816.zip using jump_1_56 because I can't update without it.
So the phone started normaly but the sound, camera not ok.
So I read that I must update also the radio. I downloaded the Kaiser_Radio_1.71.09.01 from http://webftp.myppc.it/index.php?dir=Kaiser/Radio/
I have found two methods :
the first is http://forum.xda-developers.com/showthread.php?t=393182
I tried it but when the phone is in the bootloader screen, he disappear and make a white page with a blue 'loading...' in the top,
I wait for 10 minutes and nothink ...
So I stopped the procedure, and the phone retart normaly with no problem.
I tried twice, the same problem.
So I start the second method, using the KAISERCustomRUU.exe, and of course jump_1_56 to get the bootloader screen with jump, so the procedure start with no problem until 99% ................. and here .............. ERROR ...
And now when I try to start my mobile phone, I have only t he bottloader screen with my old radio and STOPPPPPP.
In this point I try another time the first procedure with the sd card and radio 1.27.15.32 and nothing ...
NEED HELP PLEASE
original spl 1.81.000
Click to expand...
Click to collapse
rom to MyPPC_MLs_K3.1_0816.zip also check the radio version the uploader who left the rom uses that can be of great help since you will know which one to use.
I have my shares of problems when i comes to this same issue so i took the time out to help you. Cheeer man
Moving to General because the Question is NOT DEVELOPMENT related.
Hello ALL and thank's for your reply,
First to restart my mobile phone I have used the mtty.exe with this manipulations :
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
founded HERE
Second problem is to update radio, I have mysteriously found a link to a ROM update of orange France, after installing iit, my radio become 1.65.16.25 with WM6.1, I wasn't satisfied with the orange rom so I tried to install the MLS K3.1,
AND NOW .... all it's ok, sound, photo, bluetooth.
One more question please : do you think that I use my mobile with this radio or it's better to me to update it to 1.71.... is there a very difference or no ???
Link to ROM Orange France wm6.1 August 2008 HERE
Hello,
now I have another problem, I think that it's big one, I think that it's a big one, I explain.
I tried to install a new dialer, so I installed it into the phone, the phone restart ... and now nothing, he reboot continually.
I tried mtty with set 16 0, task 8, after task 0, and here he doesn't boot, I see the orange logo with the r ... g ... B .... in the left down and here STOP.
I tried Hard reset, 100 % ok BUT NOW I see only logo of Orange but not radio version, from version, nothing only the Orange logo.
So I flash with the original ROM of Orange, all is ok until 100 % but the same, he reboot, I see orange logo, 5 seconds after he rebbot another time, Orange logo, 5 seconds, reboot ....
Please help me to resolve the problem.
after 5 minutes without battery, I get the information in the left down and the mobile start with the WM6.1.
So I can't install a new dialer :-((
Thank's a lot
thehou said:
Hello,
now I have another problem, I think that it's big one, I think that it's a big one, I explain.
I tried to install a new dialer, so I installed it into the phone, the phone restart ... and now nothing, he reboot continually.
I tried mtty with set 16 0, task 8, after task 0, and here he doesn't boot, I see the orange logo with the r ... g ... B .... in the left down and here STOP.
I tried Hard reset, 100 % ok BUT NOW I see only logo of Orange but not radio version, from version, nothing only the Orange logo.
So I flash with the original ROM of Orange, all is ok until 100 % but the same, he reboot, I see orange logo, 5 seconds after he rebbot another time, Orange logo, 5 seconds, reboot ....
Please help me to resolve the problem.
Thank's a lot
Click to expand...
Click to collapse
try for radio upgrades, maybe it can help you! you can look here ===>> http://forum.xda-developers.com/showthread.php?t=393182 try to continue and do not despair
Hakim Rahman said:
try for radio upgrades, maybe it can help you! you can look here ===>> http://forum.xda-developers.com/showthread.php?t=393182 try to continue and do not despair
Click to expand...
Click to collapse
Salam, thank's for your response
From the last install of dialer and the bug of reboot, I have reflash my tytnii correctly BUT the problem that I have now is when my sim card is installed, the phone reboot systematically.
If I leave the simcard in the phone but I start with the Off line mode, it's ok, Just I change the mode to telephone here .... reboot ...... what the dialer have made in my phone ???????
thehou said:
Salam, thank's for your response
From the last install of dialer and the bug of reboot, I have reflash my tytnii correctly BUT the problem that I have now is when my sim card is installed, the phone reboot systematically.
If I leave the simcard in the phone but I start with the Off line mode, it's ok, Just I change the mode to telephone here .... reboot ...... what the dialer have made in my phone ???????
Click to expand...
Click to collapse
I think you get caught by Simdoor issue ...! try to search for sim unlock program for kaiser and install on your PC !!! You can find it here -->> http://forum.xda-developers.com/showthread.php?t=375583

Categories

Resources