PLEASE HELP - stuck at 4 stripes screen - MDA III, XDA III, PDA2k, 9090 Software Upgrading

I think this time my BA really turned into paper weight
I performed IVAN ROM 3.3R4 as instructed, the installation was successful but because in the past when I was upgrading to Tuma 1.3 from WM2003se, I only formatted 128kb as ext rom.
So after IVAN ROM was installed, I perform the format again, and set 8000kb, this time after the new installation I am unable to proceed after the 4 stripes even thought i had press camera and record button, and chose YES for the 2nd and 3rd option. Please tell me how I can possibly get the phone to work again.
I am seriously in deep **** now

What version of the IVAN rom did you use?

Related

HELP!!! VERY URGENT!!! MY SCREEN FREEZED ON BOOT COLOURS

Hi
I am really desperated
I have upgraded my PDA2K to wm5 and was working ok until today that freezed on the bootable colour screen.
What should I do? Please help me
NO WORRIES at xda-developers
All you need to do is go to the (Boot options) Just reset the device, as soon as it starts quickly press Record and Camera button together before the version appears at the bottom. Use the record button to scroll up and down and camera for switching it to YES or NO. Leave the top one (Enable KITL = No) and the rest of two i-e (Clean Registry Hive) and (Format Storage) change both to YES. Then press Mail button. You will see a white screen, wait for a while, you will see a start up screen for the fresh setup  If the problem still exist then put into Boot Loader (Record + Power and Reset) the device will show you Serial and USB when it is docked with the cradle. First install the W 5 again, hope this will work, if all this doesn’t works, Downgrade it to 2003 SE, Only by installing the correct ROM (available here at XDA-Developers that is without EXT ROM) cause other shipped ROMs won’t work that are provided by vendors. This will work for sure. Later you can upgrade it again with W5. And yes if you want to stick with 2003 se, just unhide the Ext Rom and simply update it with you shipped ROM provided by your device vendor. Good Luck
I'M STILL IN TROUBLE - PLEASE URGENT HELP
Thanks for your kwik reply.
I have tried all that you have porposed but still nothing.
I have tried "Just reset the device, as soon as it starts quickly press Record and Camera button together before the version appears at the bottom. Use the record button to scroll up and down and camera for switching it to YES or NO. Leave the top one (Enable KITL = No) and the rest of two i-e (Clean Registry Hive) and (Format Storage) change both to YES. Then press Mail button. You will see a white screen, wait for a while, you will see a start up screen for the fresh setup" but stucks on the white screen.
I have tried to downgrade following the intructions but when should recognise the ROM comes completely in blank.
Please help.
More info please
Finally I was able to downgrade it. Will leave it like it is. Thanks for your help.
But now I have another problem. is crashing all the time, what can i do?
Prefer (HTC_Blueangel_WM5_Wizard with 1.5 Radio)
:wink: no problem dear, just upgrade it again to W 5 Prefer (HTC_Blueangel_WM5_Wizard with 1.5 Radio) and this time make sure you stop all these services. rapimgr.exe, outlook.exe, winword.exe, wcescomm.exe, wcesmgr.exe.
(Right click on taskbar -> Task Manager. End the mentioned processes) Do Not Install Resco File Explorer cause it hangs!
Hope this time you will be more prepared to face these kind of problems.
And if you really want to stick with 2003 se, format your device with 60 kb and unhide the Ext Rom, when you see the extended Rom in (Settings -> system -> Memory -> Storage Card), then just reinstall your The Original Shipped Rom (2003 SE) that can be downloaded from the carrier.
ROM version: 5.03.02 WWE
ROM date: 03/02/05
Radio version: 1.15.00
Protocol version: 1337.45
ExtROM: 1.1.9.106
Where can I download that from?
thanks for the reply
Where can i download the HTC_Blueangel_WM5_Wizard with 1.5 Radio from?
good decision
Use the current avaialbe Wizard ROM, later upgrade Radio available at http://buzzdev.net/component/option,com_remository/func,fileinfo/id,225/. Just run MaUpgradeUt_noID.exe in Bootloader mode.
good decision
Use the current avaialbe Wizard ROM, later upgrade Radio available at http://buzzdev.net/component/option,com_remository/func,fileinfo/id,225/. Just run MaUpgradeUt_noID.exe in Bootloader mode.

Stuck in BA WM6 Upgrading

I'm Stuck in BA WM6 Upgrading.
I was at the HTC_Blueangel_WM6_Wizzard Upgrade 4
After execute the installer file I performed a Hard Reset
Colored stripes (the bootscreen) will appear on the screen but I can't ge no debugger screen at all: the BA remain in Bootscreen with R 1.11.0 at the right bottom of the screen.The battery was full. I've tried the mtty procedure as well...no way out. Any clue ????
Have you follow all this steps here?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade1
Yes I did and now I'm Stuck at
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
And what device do you have in fact? Qtek 9090? Other??
Mine is a Qtek 9090 and didn't have any trouble...
Same problem here, wm6 was already running; downgraded to 2003 SE to repartition the extrom, wanted to flash to wm6 again; now my xda3 is stucked after flashing, only r 1.10.0 is shown, no chance to carry on...???
I've got imate pda2k ct2cwj...and Heinzibua I'm stuck on R 1.11.00 do you have an Imate as well ??? cause I guess the official XDA procedure doesn't work for this kind of model (mine was an Italian W2003).
I'm very upset about this...
@ conosciani.m
wm6 worked well on my xda3 , problem was only after repartitioning the extrom.
I'm going to think I did somenthing wrong during the extrom steps..so i've returned back to wm2003 and I'm going to try the upgrade again
please tell me, if you find the solution...
running again
i repartitioned storage in 2003SE set to 20000 kb.
flashed to WM6, no problem now, storage is 41,25 MB, but running !!!
I did it too, I had to reinstalled w2003 and dit the Upgrading BA WM6 wizard again.....
after UNHIDE the rom, this time (and not in the previous upgrading), I did it the rom format using MTTY after that I ran the upgrade procedure and I got the WM6 running.
Happy for both of us to reach the goal......
do you have 60 MB storage now ?
can you give me more infos about MTTY ?
thx
tried to set storage to 60mb again, stuck again, also if i do just the same procedure as yesterday it is stuck; start to hate this device.
please tell me, what you did exactly to make it run. tried mtty also, but don´t know, what to do...
try this...
1. downgrade to 2003
2. copy the utils to the phone(extrom utils and repart_doc.exe)
3. install extrom utils...
---a. tap unhide... ok.
---b. tap unlock... ok. may throw an error but still ok...
---c. reset...
4. run Repart_DOC
---a. Set it to 128 byte
---b. Go/Start/Format (it should succeed)
5. reset to bootloader
---(press and hold record + power button then stick reset)
6. flash WM6 ROM
7. cold boot (press and hold power button then stick reset)
8. (optional) if stuck in the "tri-color"(white isnt a color ) screen...
---Hard Reset. Using No/Yes/Yes option.
reading further about the Repart_Doc topics...
128byte is the smallest you can format/resize the extrom
to maximize the storage in WM6.
Thx, that´s exactly what i did many times without success...
but now it works, after upgrading radio rom there also was no problem with upgrading to WM6; 60 MB rom; i only want to upgrade to radio rom 1.15, then i´m happy.
thx everybody for your help

I Think I've Bricked My Blue Angel????

Hi,
I am new to attempting ROM upgrades!
I bought my BA on ebay it runs on wm2003se but have never used it as a phone because it needed unlocking so i thought i would try to upgrade then unlock.
After many failed rom upgrade attempts one finally started to install, it got to 100% then i was promped to soft reset my XDAiis which i presume is the normal proceedure?
So i did this, but now it is stuck on the blue, green, red and white screen displaying,
No GSM
HTC BlueAngel D 6. 50.28.WWE
I have tried hard reset
I have tried to install the O2 rom that came with it but it says its the incorrect country version!
Any ideas or is it Dead???
HELP
first: try hard resetting!
the procedure changed in comparison to wm2003se, so you have to press reset+power, and then immediately press camera+record. a menu shows up, showing
Enable KITL YES
clear reg. hive NO
format storage NO
using the camera and record buttons, change these entries to
Enable KITL NO
clear reg. hive YES
format storage YES
and press the mail button to confirm, after some time you will see the device boot for the first time.
probably that solves your first problem, but since you seem pretty unexperienced (no offense), it probably unveils more problems. you should also make sure to read this carefully, maybe follow the upgrade wizard again, to make sure you formatted your old extrom and resized it, have a working radio rom, and to make sure you know what you are doing and how to go on improving you BA experience:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardMain
greetz
Chef_Tony
Hi,
Thanks for your reply i have tried hard reseting and still have the same problem, any other suggestions???
run through the wizard in the link above, you will need to downgrade to wm2003se again, resize the storage space, upgrade to wm6.5 doing everything exactly as written in the wiki and you will have no problems, here there is the step you are currently facing:
http://wiki.xda-developers.com/index.php?pagename=BA_Downgrade_WM5
the downgrade from wm5 or above down to wm2003
hello !
my screen stay white after the
"Enable KITL NO
clear reg. hive YES
format storage YES"
part. How can I do ? thanks
and it's a xv6600
i am not an expert when it comes to the different names of the device, but a quick google search told me, your device is not a blueangel, but a cdma device, namely a HARRIER. the harrier does not support wm5 and up, so you should flash your original shipped rom back, to get it back to work.
if you do not have your shipped rom present (on cd) you can go to your carrier's website and try and download it there. if, however, it is not listed there anymore, you can go download it here:
http://harrier.atspace.com/
all credit for the shipped rom archive goes to xplode.
greetz
Chef_Tony
great link thanks

Unable to Load Bootloader

I have tried hitting record + power + reset and still no dice.
I did this last Jan to my BA with few problems, put in the wm6.1
Wanting to install this one WM6.5
I also installed the Wizard Service Tool and it doesnt seem to work. It will give me info but the hard reset and other rom features don't want to work.
is there a workaround for gettin to the bootloader? Or should I take this all as a sign not to brik my phone? ;D
thanks,
chela
hi , i'm new on the forum...i think i've the same problem, on my PDA2K..
I try to install a new rom from wm2003se, using a file called "preparazione BA"( i think i've unlocked the extrom), then i normally setup with the MaUpgradeUt_noID.exe..But now, when the upgrading is completed to wm6, i'm not able to load the bootoption..i can see 4 colour bands (green blue red white) but no option to boot. The rec+photo+reset seem not to work.
Could anyone help me\us??
Regards at all
Davide
after 2 hours..here are some news: my pda2k display became with the 4 color but there was writen something about R none, G none and (version onf the rom i tryed to install) then pressing rec+cam i saw for little fraction of second the menu enable kitl ,clean registry, etc.. and then suddenly the wm6 starts. After installing the OS ask me to reset..Well, it return to the same 4 color, and the only word i see is R1.11.00
I'm getting crazy...
Please big chef tony help me!
i don't know what to do now...i'm little down
Davide
...lol maybe because I dont do this often enough, but this case was solved with a little bit of RTFM!
I didnt realize I was pressing the wrong fsking button! derr!
Here is Chef Tony's post...should carve it into my desk!
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
i've solved my problem..reading on other forums, they suggest to install a rom WM5, where there was radio upgrade too..After i was able to install WM6.1 ! Now..i have to wait..and crossing my fingers!
Thank you all, if anybody has question ask me, i'll happy to help you
Bye
Davide
Davidenji said:
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
Click to expand...
Click to collapse
Nothing strange about what is in photo #2! That is the debugger screen.
Looks like you got it rolled back to the original ROM but if you decide to put the latest stable ROM 6.5 on there you're going to have to follow the Chef's directions in the above supplied link.
Good luck,
Chela
glad you found it out, you are right, there was something wrong with the radio, which is why in screenshot #1 there is only the radio listed and i think that's also why in #4 the comm icons are red, i've never seen that before, but could also be a custom skin in that rom.
brujeria is right, there is nothing wrong with the 2nd and 3rd screenshot, except for the 2nd one only showing the rom and no radio or protocol, meaning that the device was probably resetted by pulling out the battery and not pushing the reset pin with the stylus, unless that was also a radio issue.
unless you already started customizing your device you should probably think about hard resetting it once again and trying if that works, or even re-flash the rom, without flashing the radio, that way you'd know for sure, if from now on you'll always have to flash a "baked rom" (usually a term for a cooked rom, together with radio and extrom, a full flash, in this case i mean rom and radio rom, since the extrom is not really flashed anymore).
with best regards,
Chef_Tony
i've already customized...a little! Now, everytime i soft reset i read this: R 1.15.00 , G 1337.45 , D 1.21 michy.
I've no problem at moment..but i hope i won't never hard reset!
This Rom (WM6.1 included only Rom upgrade) it's nice, but i'm interested about WM6.5..anyway i think to keep this one untill a problem will come out
P.s. Like you say, now the antenna isn't red anymore..it's bright green
Thank you a lot for the support guys!

[Q] SD ROM flash not working...

I have installed android on my Kaiser (Incubus26Jc_'s Super FroYo RLS15 All Language) and I want to go back to my custom WM ROM, but I've never managed to flash a ROM from the SD card, although I've respected all steps (SD card FAT32 formated, WM ROM renamed as KAISimg.nbh and put on SD root, together with KAISDIAG.nbh, pressed power & camera button and pushed the reset button)... I can get to the 3-color bootloader but for 1 second appears a message (I think is something like "no image file" but I cannot read it because it dissapeared too quickly) and then the word "serial" at the bottom of the 3-color screen, and it remains like this until I make a new reset...
As I cannot use ActiveSync anymore (due to Android OS) and I cannot flash through USB, I have no option now to get back to WM!!!
Could somebody give me an advice how to do it?
Thanks in advance!
...nevermind... I've solve it... just look at this (for others with same problem):
http://forum.xda-developers.com/showthread.php?t=423486
I have to say, this is a great forum, I can find almost always a solution for my problems!
I got the same problem, I flashed a tpc rom (well my brother actually) a while back. And I was never able to load up the bootloader with all the key combinations I can think of
(hard reset, power+camera, batery out and turn on+camera)
I also took a look at the link above me. I couldn't find an answer .
Someone please help me out.
mmh, Is there no1 with a solition to fix this>
I really hate the fact the tpc rom prevented me going into mah bootloader.

Categories

Resources