Database Develop

sx66 bluetooth expired. missing rom... here is a sollution!

SX66 BLUETOOTH Expired
Hi. I can not use Bluetooth since I downgraded from wm2005 to WM2003. When I set up Bluetooth, it says”
BTTrayCE
Sorry! Bluetooth can no longer be used because the license is expired
BDA: 00:00:00:00:00:00
Key:
E3E534E19B3E8214C543A
73COABB9A9074DD3B175
3515CD8
Please help. Thanks. I have tried completed install from original rom CE nad Radio. But the same problem. The extended rom is dead I can not upgrade it since it faila at 1%.
Please help Thanks.

Hi
Did you carefully follow WM2005 -> WM2003 process described in wiki ?
It's very important that you resize, reformat ExtROM and do some other stuff before flashing back to WM2003.
Good luck

i have the same problem.. since octobre without solution

Hi
I ask again.
Did you guys restore your ExtROM correctly ?
(using Repart_DOC.exe tool)
GO to wiki -> blueangel -> blueangel WM2005 page -> how to downgrade....
Good luck

hi robal
I tried but when i use Repart_DOC
I set size 16384 or other sizes but if I click format now, the error message pops up"
Create handle failed.
Please help. Thanks!

Hi
Maybe You forgot to do as described in point "3" of downgrade process :
Prep your WM5 device by formating Storage and Hive.
Press Power + Softreset, and when the colored stripes (well, this is the bootscreen )shows on the screen.
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc.
Quickly press Record+Camera before the versions appears at bottom right
OR, press Power+Softreset+Camera+Record at the same time.
If you have a PH20B1 device such as SX66
Quickly press Record+Windows Media before the versions appears at bottom right
OR, press Power+Softreset+Windows Media Player button+Record at the same time.
Either way mentioned above should work.
You'll see three options; change the second and the third to "yes".
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc.
You can do that with the camera and the record buttons.
If you have a PH20B1 device such as SX66
You can do that with the Windows Media Player and the record buttons.
If you are done, press the mail button, it'll show a white screen for a while, just wait.
If the bootscreen, aka. the colored stripes is displayed, Wait more, you are booting.
The welcome screen to set up your device should appear soon.
Click to expand...
Click to collapse
This should've been done when you had WM2005.
I think it's important to do it, before trying to run Repart_DOC (on WM2003).
Any idea ?
If you've forgotten to do it. You probably will have to intall WM2005 again, do it, intall WM2003 and Repart_DOC it. HUh
have fun

DEAR robal,
Thanks for your information. In fact I did everything like you said before. but nothing help.
I know that I have to creat an extended_Rom in order to get it work. (this is not a big deal since we can install manually.
The most imfortant thing is the bluetooth error. Please help me find a sollutin for it. Thanks!

Hi
So you say, you have WM2003 installed with Extrom CABs from some official ROM ? OK
I'm not familiar with this BT failure. Please tell me exactly what ROM are you using ( CE , Radio, ExtROM )
And what version of BT stack you have.

This error is caused by a portion of the Bluetooth memory being overwritten by something else. The people who are trying to help you are right...you need to reflash the device because something didn't work correctly last time.

I had a tool that restored BT MAC-address, but I cannot find it on HDD.
It was sent by imate tech support as a fix for the "bt license has expired" error, so you may try to contact them, or search this forum.

please mamaich if you can find it this will be very helpful

Dear mamaich,
Thanks for your great imformation. I love to get it as soon as you find it. Again, thanks for your pricious time to repond.

Looks Like every body is stuck...I had solved this problem twice and with full success...on ROM 1.4 pls install the Broadcom 1.6 cab and yes...yr problem is solved... :lol:
Only thing..I was not able to put it install thru Ext ROM...even by editing config.txt....may be someone here can do this :roll:

new problem come out after previous one
hi, I have another problem so.. i need your help.
before, My sx66 problem with bluetooth and the Extended_ROM did not exist.
Now, after many tried to install rom from Tmobile, O2. sx66 over and over again, the extended_ROM is now okay to install but sadly the Storage doen't exist any more. Also some contact, task .. pop up after full installation. Finally,after extended_ROM Complete installed, window
Connection Flash Mangaer
pop ups" Saved data is corrupted.
System will erase all data to fix
this error
Yes No
but It does fix anything after I click yes button.
Please help to recover my storage. If there any software that can partition rom for ppc. please share.
p.s. the bluetooth now is freezing.

what u hv to do is use the Ext ROM Unlocker and use Repart_Doc...Set the size of yr Ext ROM...say 15 MB or so and then do the Repartitioning...now flash yr device...u will get yr Ext Rom Back with no such errors as reported by you

problem solved.
Dear hdubli,
Thanks for your help. Everything works properly now. Now my sx66 works at factory shipped. I am very happy.
Specailly thank to Hdubi for providing an exellent solution.

hdubli said:
Looks Like every body is stuck...I had solved this problem twice and with full success...on ROM 1.4 pls install the Broadcom 1.6 cab and yes...yr problem is solved... :lol:
Only thing..I was not able to put it install thru Ext ROM...even by editing config.txt....may be someone here can do this :roll:
Click to expand...
Click to collapse
Hi hdubli, a question, what is the ROM 1.4 of the blueangel?

Problem with Qtek 9090 Camera

Hello people, I have a question for you. I recently did the Upgrade of my Qtek 9090 to WM 5 (device data now is PH20B WWE 5.03.02 1.12.00). It seems to be working fine (have yet to test wireless connection), but I discovered that I can't get the camera on the phone to work. For some reason, it simply does not react to camera button. It also does not react even when I try with the manual startup of pictures & videos application. Does anyone has any idea how to get out from this one? If this is any help, the original phone data were PH20B 0 B WWE E DANGA102 1.40.00 0 0 1.40.147 1.12.00 12.00.
Thanks a lot

Simple but crucial question: Which WM5 rom you flashed? Have you read specific information about this rom? maybe this one requires some post-instalation operations?

Basically, I found this ROM on www.buzzdev.net, and it only stated BA WM2005 5.03.02WWE - standard upgrade. It is basically the only one which worked for me, since every other dumped me (the model of the phone matched the ROM). However, there were no additional explanations for this, so I am stuck. Is there any registry tweak, or aditional piece of software which could make it work, or I will have to go looking further for better ROM?

As long as we don't know what is the problem with the ROM, we cannot help you - some ROMs just had camera support cut out, others needed installing additional software, some had errors.
About model/device check: please take any recent WM5 rom (baniaczek's for starters) and just read carefully flash instructions from Wiki - there is no problem with device check, if you understand what you do and how you should do it.

Thanks Jakub for good advice, I've been doing some reading and I tried baniaczek's latest issue from the web. However, I've got stuck. Namely, MaUpgradeUt_noID.exe does not work in my case. It simply tells that there has been communication error with the device, or if it starts it tells that this ROM upgrade utility was not designed for this device. I tried the other way with BaUpgrade.exe, with usage of EditFix.bat and xda3nbftool.exe, but it seems that I'm doing something wrong - each time I get the message that the specific ROM was not written for me and that I should check my vendor. Is there any way to get out of this, since now it seems that I can't do no upgrade or downgrade at all?
Thanks a lot in advance, I know this is mostly due to my mistakes and usage of unchecked ROMs.

Thank to everyone who was trying to help me. I did some experimenting in order to solve the upgrade issue, and I solved the problem. This is how I did it: Namely, I downloaded KitchenAKU3.5v2-xplode, which also contains useful readme. Basically if you want to have MaUpgradeUt_noID.exe to work for you at all, you have to put the device in Bootloader mode (press power + record simultaneously). After that, the upgrade went smoothly, after I designed my own rom, which was very easy with xplode's tutorial.
One more thing I did was that after the upgrade, I did a soft reset and "cleanup" of the device. after the soft reset I changed following options on the boot screen using camera and record buttons:
“Enable KITL” set to NO
“Clean Registry Hive” set to YES
“Format Storage” set to YES. (again on xplode's instructions)
After that, I confirmed settings with pressing of the mail button. One minute later, I had fully operational and very fast QTEK 9090 running WM5.
I hope that some things I did will be useful to other people trying to fix their blue angels. And of course, thanks to Xplode for making an excellent user-friendly upgrade.

Stuck in BA WM6 Upgrading

I'm Stuck in BA WM6 Upgrading.
I was at the HTC_Blueangel_WM6_Wizzard Upgrade 4
After execute the installer file I performed a Hard Reset
Colored stripes (the bootscreen) will appear on the screen but I can't ge no debugger screen at all: the BA remain in Bootscreen with R 1.11.0 at the right bottom of the screen.The battery was full. I've tried the mtty procedure as well...no way out. Any clue ????

Have you follow all this steps here?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade1

Yes I did and now I'm Stuck at
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4

And what device do you have in fact? Qtek 9090? Other??
Mine is a Qtek 9090 and didn't have any trouble...

Same problem here, wm6 was already running; downgraded to 2003 SE to repartition the extrom, wanted to flash to wm6 again; now my xda3 is stucked after flashing, only r 1.10.0 is shown, no chance to carry on...???

I've got imate pda2k ct2cwj...and Heinzibua I'm stuck on R 1.11.00 do you have an Imate as well ??? cause I guess the official XDA procedure doesn't work for this kind of model (mine was an Italian W2003).
I'm very upset about this...

@ conosciani.m
wm6 worked well on my xda3 , problem was only after repartitioning the extrom.

I'm going to think I did somenthing wrong during the extrom steps..so i've returned back to wm2003 and I'm going to try the upgrade again

please tell me, if you find the solution...

running again
i repartitioned storage in 2003SE set to 20000 kb.
flashed to WM6, no problem now, storage is 41,25 MB, but running !!!

I did it too, I had to reinstalled w2003 and dit the Upgrading BA WM6 wizard again.....
after UNHIDE the rom, this time (and not in the previous upgrading), I did it the rom format using MTTY after that I ran the upgrade procedure and I got the WM6 running.
Happy for both of us to reach the goal......

do you have 60 MB storage now ?
can you give me more infos about MTTY ?
thx
tried to set storage to 60mb again, stuck again, also if i do just the same procedure as yesterday it is stuck; start to hate this device.
please tell me, what you did exactly to make it run. tried mtty also, but don´t know, what to do...

try this...
1. downgrade to 2003
2. copy the utils to the phone(extrom utils and repart_doc.exe)
3. install extrom utils...
---a. tap unhide... ok.
---b. tap unlock... ok. may throw an error but still ok...
---c. reset...
4. run Repart_DOC
---a. Set it to 128 byte
---b. Go/Start/Format (it should succeed)
5. reset to bootloader
---(press and hold record + power button then stick reset)
6. flash WM6 ROM
7. cold boot (press and hold power button then stick reset)
8. (optional) if stuck in the "tri-color"(white isnt a color ) screen...
---Hard Reset. Using No/Yes/Yes option.
reading further about the Repart_Doc topics...
128byte is the smallest you can format/resize the extrom
to maximize the storage in WM6.

Thx, that´s exactly what i did many times without success...
but now it works, after upgrading radio rom there also was no problem with upgrading to WM6; 60 MB rom; i only want to upgrade to radio rom 1.15, then i´m happy.
thx everybody for your help

I can't tell if I have successfully Hard SPL'ed

Hi
I am having some problems when trying to upgrade my Orange SPV M700 to Hard SPL. I have followed the instructions given in "TrinityGuides.info" but I am not convinced the Hard SPL has actually worked okay. This is what happens:
1) I follow the initial instructions (run ROMUpdateUtility.exe) and click on the various screens ("I understand" "I completed") etc
2) I get to the point where the screen says "You are now ready to update your ROM image. This operation takes approximately 10 minutes"
3) I then click on "Next", the progress bar screen appears and I get the message on my SPV about running programs - I select 'yes' on the SPV.
4) Immediately I hear the Windows XP 'dum-dum' noise letting me know that a USB device has been disconnected. Also my ActiveSync is gone. I have not done anything to cause this though - the connection just goes down.
5) I then get a message telling me that the device is not connected and I have to exit the Hard SPL routine.
6) After reading the FAQs on TrinityGuides.info I re-run the "ROMUpdateUtility.exe" and get to the progress bar screen again. This time I see the grey screen on the SPV, with progress bar rapidly completing on both the SPV and my Desktop screen progress bar.
7) After literally a few seconds I get a screen telling me "Congratulations! Your ROM update is now complete etc"
Even though I see the congratulations message I am not convinced it has successfully installed Hard SPL.
Firstly, whereas the messages suggest it can take up to ten minutes to do the Hard SPL mine only takes a few seconds. Secondly, when I follow the TrinityGuides.info instructions on how to check the Hard SPL (by pressing power, camera and soft reset) I see this:
On my tri-colour screen this is displayed:
IPL-0.50
SPL 1.07.0000
The "TrinityGuides.info" instructions say that I should see this:
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
I have tried both the "Hard SPL 1.20.Olipro" and "Des' Crash-Proof SPL" but nothing makes any difference to the display I see.
Can anyone help me? I am concerned that if I don't have the Hard SPL correctly installed I am going to risk bricking my SPV if I try upgrading the ROM, unlocking the SIM etc (which is what I want to do). Is there any other way I can tell whether Hard SPL is installed correctly?
Thanks in anticipation!
Spivvy

If i remember correctly hard SPL is a quick process, it's the ROM flashing that takes ten minutes or so. As to why it's not working i can't offer any help, sorry.

Hi DeeDee
Thanks for taking the time to reply. If, as you say, the Hard SPL does happen very quickly (in my case it seems a second or so) then that's good to hear as I was sure something had gone wrong.
Does anyone know if what I see on my tri-colour screen is correct? (i.e. IPL-0.50, SPL 1.07.0000) as before I proceed with any more drastic updates I'd like to make sure my SPV is protected against bricking.
Thanks again
Spivvy

UPDATE.....
I spotted this person's solution to what seemed to be a similar problem to mine:
http://forum.xda-developers.com/showthread.php?t=382246&highlight=ActiveSync+disconnects
I decided to try his fix. I used Olipro 1.20 Hard SPL.
The Hard SPL procedure did continue in a more convincing manner than my previous attempts, and the progress bar took a bit longer to complete, and I also received a message telling me that the operation was successful. I then did a soft reset and felt that maybe this time it had worked.
In a rare moment of feverish optimism I pressed the buttons to check the SPL version now on my Orange SPV (power, camera and soft reset). However, it is still telling me this:
IPL-0.50
SPL 1.07.0000
i.e. nothing seems to have changed. No sign of Olipro's SPL again.
In a word, I am flummoxed.
In two words, I am very flummoxed.
So, I am still putting out an appeal to you clever bods as to how I establish if I have a safe Hard SPL on my Orange SPV, or is it still looking a bit iffy (a technical term for "not very good")
Thanks
Spivvy

i am seeing the latter version with OliPro SPL, OK it's v1.2 but it's still different from yours.
Are you trying this on Vista or XP, personally i have always used XP for flashing. Whether that's going to make any difference i don't know.

I have a question along similar lines, although not identical. I'm completely unable to get from the triband screen to the bootloader screen. I'm trying to flash from my mini-SD card, but one it gets into that SSPL triband screen, it doesn't do a thing. I'm running vista on my PC, and can't seem to get any useful action trying to flash from there. Getting a little frustrated, cause I haven't even been able to SIM unlock my phone so far... Considering going the IMEI route, although that won't do anything for bootloader and upgrapding ROM later on... Any advice, or should I just use IMEI and go the easy way?
Dan

Hi DeeDee
I am using Windows XP, which I think is the preferred OS for this type of operation. Very puzzling.
Thanks
Spivvy

Hmmmm.....
It's looking like I am not going to resolve this problem as no one has posted an actual solution. I am not sure what to do now - my gut feeling is that my SPV M700 has not been Hard SPLed (based on what it displays as described earlier).
All I know is that I have followed the TrinityGuides instructions (and other postings with information about this type of thing) accurately. I have done it several times (using both Olipro 1.2 and Des Crash Proof) - but, for some inexplicable reason, my SPV M700 would appear to refuse to accept the Hard SPL.
As no one has said otherwise I have to assume that the tri-colour screen information I see in bootloader mode does mean that I have not successfully SPLed?
I can't understand why some (in fact most) people seem to get the Hard SPL flashing performed okay and yet mine refuses. I know from searching the postings that there are a few unlucky souls like me who have not been able to do it successfully.
If anyone does have any suggestions I really would be grateful to hear them, but for now it looks like I have drawn a blank. Pity.
I have run out of ideas - could it be some other program I have installed is interferring with the process? Is it my version of ActiveSync (4.5.0)? Is it some setting I have got on the SPV M700 that is preventing the Hard SPL? There surely has to be a reason why the Hard SPL is not working?
Still hanging on, hoping that some shaft of light might shine on my SPV M700 one day...
Ho hum...
Spivvy

Hey u are not alone, my Trinity ( Dopod D810 variant ) just simply refuses to flash to any hard spl as well, same problem as yours, i am using windows xp to flash so i doubt its the driver problem.
I found a solution to this problem though, i use SSPL to flash cooked rom to my device.
http://forum.xda-developers.com/showthread.php?t=293632
Just paste the .exe onto your trinity and open it using file explorer, it should enter bootloader with a "by des" behind the bootloader number, it should be safe to flash then.
I tested flashing WM 6.5 by savesaint, Finix's 6.1 with no problem
ADDons: Anyway the reason i suspect is because my one has been flashed with HTC P3600 rom, yes, by HTC without dopod branding, hence the problem

Hi there - thanks for that tip. I will try that link you suggested, and have a go with the file. I'll get back to let you know how it all went.
Many thanks for taking the time to post your suggestion.
Cheers
Spivvy

Hi
I thought I would report back as to the progress (or lack of it) regarding the failure to Hard SPL my Orange SPV-M700. There's not much to report I'm afraid, which may be largely to do with my lack of confidence etc.
I checked out the link suggested above by "/b/-TarD" (using SSPL to flash cooked rom to device - as described at:
http://forum.xda-developers.com/showthread.php?t=293632
However, when I read the various posts and experiences I still felt that this might not be the solution I was looking for. I am not very technical with all this ROM flashing but the original Hard SPL method seemed to me to give me some insurance against bricking my SPV-M700. This SSPL does not seem to leave you with a Hard SPLed device (I am not exactly sure what it does to be honest), and in fact some people seem to have had quite difficult problems after using it.
Call me a cowardly old geezer but I have backed away from trying the suggested solution at the moment (but still very grateful to user "/b/-TarD" for his suggestion).
My aim was to:
1) Get the basic HARD SPL on my SPV-M700 - Olipro or Des, but having followed all the Trinity guides faithfully, it would appear that my device doesn't wanna play ball with me — very frustrating.
2) Re-instate/upgrade the GPS radio thingy (which I believe you lose after you Hard SPL)
3) Unlock my Orange SPV-M700 so that I can use any SIM card in it
4) Then, finally, consider upgrading the ROM to one of the newer WM6 versions, or a better WM5 version.
But, at the moment, it would seem that it's not to be.
Ho hum....

Unable to Load Bootloader

I have tried hitting record + power + reset and still no dice.
I did this last Jan to my BA with few problems, put in the wm6.1
Wanting to install this one WM6.5
I also installed the Wizard Service Tool and it doesnt seem to work. It will give me info but the hard reset and other rom features don't want to work.
is there a workaround for gettin to the bootloader? Or should I take this all as a sign not to brik my phone? ;D
thanks,
chela

hi , i'm new on the forum...i think i've the same problem, on my PDA2K..
I try to install a new rom from wm2003se, using a file called "preparazione BA"( i think i've unlocked the extrom), then i normally setup with the MaUpgradeUt_noID.exe..But now, when the upgrading is completed to wm6, i'm not able to load the bootoption..i can see 4 colour bands (green blue red white) but no option to boot. The rec+photo+reset seem not to work.
Could anyone help me\us??
Regards at all
Davide

after 2 hours..here are some news: my pda2k display became with the 4 color but there was writen something about R none, G none and (version onf the rom i tryed to install) then pressing rec+cam i saw for little fraction of second the menu enable kitl ,clean registry, etc.. and then suddenly the wm6 starts. After installing the OS ask me to reset..Well, it return to the same 4 color, and the only word i see is R1.11.00
I'm getting crazy...
Please big chef tony help me!
i don't know what to do now...i'm little down
Davide

...lol maybe because I dont do this often enough, but this case was solved with a little bit of RTFM!
I didnt realize I was pressing the wrong fsking button! derr!
Here is Chef Tony's post...should carve it into my desk!
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners

Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08

i've solved my problem..reading on other forums, they suggest to install a rom WM5, where there was radio upgrade too..After i was able to install WM6.1 ! Now..i have to wait..and crossing my fingers!
Thank you all, if anybody has question ask me, i'll happy to help you
Bye
Davide

Davidenji said:
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
Click to expand...
Click to collapse
Nothing strange about what is in photo #2! That is the debugger screen.
Looks like you got it rolled back to the original ROM but if you decide to put the latest stable ROM 6.5 on there you're going to have to follow the Chef's directions in the above supplied link.
Good luck,
Chela

glad you found it out, you are right, there was something wrong with the radio, which is why in screenshot #1 there is only the radio listed and i think that's also why in #4 the comm icons are red, i've never seen that before, but could also be a custom skin in that rom.
brujeria is right, there is nothing wrong with the 2nd and 3rd screenshot, except for the 2nd one only showing the rom and no radio or protocol, meaning that the device was probably resetted by pulling out the battery and not pushing the reset pin with the stylus, unless that was also a radio issue.
unless you already started customizing your device you should probably think about hard resetting it once again and trying if that works, or even re-flash the rom, without flashing the radio, that way you'd know for sure, if from now on you'll always have to flash a "baked rom" (usually a term for a cooked rom, together with radio and extrom, a full flash, in this case i mean rom and radio rom, since the extrom is not really flashed anymore).
with best regards,
Chef_Tony

i've already customized...a little! Now, everytime i soft reset i read this: R 1.15.00 , G 1337.45 , D 1.21 michy.
I've no problem at moment..but i hope i won't never hard reset!
This Rom (WM6.1 included only Rom upgrade) it's nice, but i'm interested about WM6.5..anyway i think to keep this one untill a problem will come out
P.s. Like you say, now the antenna isn't red anymore..it's bright green
Thank you a lot for the support guys!