Database Develop

orange tytn II unlockable?

Well I would like to get another software because the orange software is pretty much the worst one you can get.
I’ve been trying to update from wm6 to wm 6.1 but I had to hard reset my phone many times cause whenever I try to flash the rom, I get that white screen that stay at 0% during the whole process to finally see an error not on the devise but well from the software (running on vista).
Please help!!!!!!

few things to remember befoe u do anything to ur phone:
1) read kaiser wiki
2) from wiki follow links on how to flash hardspl on to ur device.
3) go to kaiser rom development forum and read the first sticky containing info about flashing.
flashing hardspl will cid and sim unlock ur device.
Plz do read and search or u will mess up ur toy.

isn't there an issue with flashing orange ones something to do wit the radio and not to change it? I want to flash mine but the wiki isn't too clear on orange versions

doesn't matter what stock rom u have, once hardspl'ed u can flash any rom/radio u want to ur device.
just make sure radio works w/rom u flash. alot of chefs include radios w/their roms and ones that don'zt will tell u which radio works with rom

technocat said:
isn't there an issue with flashing orange ones something to do wit the radio and not to change it? I want to flash mine but the wiki isn't too clear on orange versions
Click to expand...
Click to collapse
I've flashed my Orange TyTN II with no problems. So long as it is unlocked to all networks it should be OK. However if you do it then your warranty goes out the window.
Run HardSPL first
Once it is installed, double-check that it is installed by doing the folowing:
Power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
If it does not say "SPL-1.0 OliPof" then HardSPL is NOT installed.
Once HardSPL is installed you can then run jockyw2001's unlocker to unlock the phone to all networks.
Then you can flash ROMS like there's no tomorrow!

nice walkthrough mate what's the differences between the roms just peoples personal customisations? is there a huge difference from the orange version?

the chefs cook whatever they want into the different roms..basically just personal stuff or needs...so read what posts and see which one fits u most...if not...try some out and see which one u like...

Narfy, go over to read this thread ... it is one man's story of getting his Orange unlocked and 'sorted'
http://forum.xda-developers.com/showthread.php?t=386089
With an happy ending

Ok having problems trying to unlock my orange tytn2. Hard SPL is installed, Step 1 of the kaiser simunlocker has been done and verified. Following the instructions, I have reset the phone to boot screen and went to step 2, step 2 of course is a command and in xp this closes as soon as you open it. Have went to command prompt to run step 2 and it gives an error about unable to connect to usb: cannot connect to \\.WCEUSBSH001
Anyone any ideas am now stuck lol.

please ignore sorted now helps when you actually read forums lol

request for help with Kaiser (after using search and trying fixes)

Device: HTC TyTN II
Bootloader: KAIS130
SPL-3.28.0000
CPLD-8
ROM: RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship
Problem: I tried to sync the device with my desktop (running XP Media Center edition sp3) using ActiveSync 4.5 like I normally do. However, this time the device wouldn't sync and it would just hang. I unplugged the device from USB so that I could try again. The phone immediately went into bootloader. It is currently stuck in this mode.
Steps taken:
First I called HTC tech support hotline. The rep walked me through several steps, but nothing fixed the problem. We tried soft resetting, holding down the power + camera buttons and then soft resetting, hard resetting: nothing worked. He then stated that the device's ROM probably got erased when I unplugged it from USB. He instructed me to download the official 6.1 ROM from HTCs website and then try to re-flash the phone.
I tried doing this, but I still cannot get the ROM onto the device. In bootloader, I plug the device into USB and I get an error message that the device is not recognized. I soft reset the phone and then run the RUU and it begins to flash the device. After 10 minutes, I get a message saying that the flash was successful but the phone just resets back to bootloader.
After searching through the forum and wiki, I am still at a loss as to how to proceed without instruction from an expert. I think I read something about using mtty, but I am afraid to do so on the Kaiser because I read that typing the wrong instructions could be disastrous.
I humbly request any kind Kaiser experts to help me with my problem! Thanks

sir topas said:
Device: HTC TyTN II
Bootloader: KAIS130
SPL-3.28.0000
CPLD-8
ROM: RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.16.25_Ship
Problem: I tried to sync the device with my desktop (running XP Media Center edition sp3) using ActiveSync 4.5 like I normally do. However, this time the device wouldn't sync and it would just hang. I unplugged the device from USB so that I could try again. The phone immediately went into bootloader. It is currently stuck in this mode.
Steps taken:
First I called HTC tech support hotline. The rep walked me through several steps, but nothing fixed the problem. We tried soft resetting, holding down the power + camera buttons and then soft resetting, hard resetting: nothing worked. He then stated that the device's ROM probably got erased when I unplugged it from USB. He instructed me to download the official 6.1 ROM from HTCs website and then try to re-flash the phone.
I tried doing this, but I still cannot get the ROM onto the device. In bootloader, I plug the device into USB and I get an error message that the device is not recognized. I soft reset the phone and then run the RUU and it begins to flash the device. After 10 minutes, I get a message saying that the flash was successful but the phone just resets back to bootloader.
After searching through the forum and wiki, I am still at a loss as to how to proceed without instruction from an expert. I think I read something about using mtty, but I am afraid to do so on the Kaiser because I read that typing the wrong instructions could be disastrous.
I humbly request any kind Kaiser experts to help me with my problem! Thanks
Click to expand...
Click to collapse
I suggest getting in touch with the moderator named GSLEON3. He is probably going to be your best bet of getting back up and running. Good Luck

Ok, I can't get in touch with GSLEON3 (I'm sure he's extremely busy) and I don't want to pester him so if anyone else out there can help, I certainly appreciate it. Here is my theory for the solution based on further reading of these forums (but since I have no technical training I don't know if I am even on the right track). I'd appreciate if anyone with the proper knowledge can confirm or reject this course of action:
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
(taken from http://forum.xda-developers.com/showthread.php?t=394543&highlight=stuck+bootloader)
redbandana cautions that one must use HardSPL or risk bricking the device. However, in the post about SPL Questions it states:
"Well, at the moment this is where we are at. We are still investigating the full effects of what an SPL can do to vary the performance of an OS. For now there is a large consensus that the newer HTC 6.1 ROM SPL seems to work well for most of the newer 6.1 ROMS (stock and cooked)."
So my question is, will the stock SPL that came with the official HTC 6.1 ROM be ok to use mtty, or do I need to flash the old HardSPL?
I appreciate any advice on how to proceed, especially if I am totally wrong about how to fix this. Thanks!

sir topas said:
Ok, I can't get in touch with GSLEON3 (I'm sure he's extremely busy) and I don't want to pester him so if anyone else out there can help, I certainly appreciate it. Here is my theory for the solution based on further reading of these forums (but since I have no technical training I don't know if I am even on the right track). I'd appreciate if anyone with the proper knowledge can confirm or reject this course of action:
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.
(taken from http://forum.xda-developers.com/showthread.php?t=394543&highlight=stuck+bootloader)
redbandana cautions that one must use HardSPL or risk bricking the device. However, in the post about SPL Questions it states:
"Well, at the moment this is where we are at. We are still investigating the full effects of what an SPL can do to vary the performance of an OS. For now there is a large consensus that the newer HTC 6.1 ROM SPL seems to work well for most of the newer 6.1 ROMS (stock and cooked)."
So my question is, will the stock SPL that came with the official HTC 6.1 ROM be ok to use mtty, or do I need to flash the old HardSPL?
I appreciate any advice on how to proceed, especially if I am totally wrong about how to fix this. Thanks!
Click to expand...
Click to collapse
mtty is not a toy and there are some risks of bricking involved. Anyhow, it is a tool that is used for situations similar to yours. Follow the steps that are provided. Step 3 may be different for different pc's, so just look for port 1. After you run mtty, install a version of hard spl. If you plan on installing a 6.1 rom, install a spl that is compatible with it such as, 3.28hard, 3.29, or the new 3.56. I'll be around for an hour feel free to pm me.

Sorry mate, usually takes me a day to catch up with my PM's, etc...
I can't say for sure on the 3.28 SPL as I have not disassembled it. Well, technically I did, just to prove a point that it was the same as 3.29, but I didn't document any of the commands.
The 3.28 HardSPL is NOT an MFG spl, so it definitely WON'T support some functions. I don't know what all the fuss is about SPL's. I use my own customized version, based of course on Jocky's work, but it's still a 1.1 SPL version & I never have any trouble.
For the 3.28 & .29 SPL's, I do know that if you are stuck because of an RUUNBH error, the correct sequence is:
cmd>set 16 0
cmd>task 8
Task 8 is not "format", I don't know where you got that & task 0 will freeze out MTTY.
Have you done an info 8 command?
cmd>info 8
That will tell you more about the issue.
BUT MOST IMPORTANTLY, only connect mtty to USB, not to port. You can mess other things up like external drives, etc. Ports are only when connecting to OEMSBL/Radio Boot Loader.

BTW, a screwed up USB port pin or block can cause this issue as well. Take a look at the pin block, is it perfectly straight?

Ok, here's the weird thing. I was going to try the mtty to do info 8 command, and I powered on the device (it had the SIM card and microSD card removed.) The device started up and performed a hard reset, and then loaded up! It had a ROM on it! Not the original factory ROM that was loaded (which had TomTom preloaded) but the factory ROM I downloaded from the HTC e-club that I tried to flash. I thought my issue was solved, so I put in the SIM card. However, when I turned on the device (with SIM card in) I get the bootloader screen. What the heck is going on?

GSLEON3 said:
BTW, a screwed up USB port pin or block can cause this issue as well. Take a look at the pin block, is it perfectly straight?
Click to expand...
Click to collapse
Yes, it is straight.

Hi everyone,
Thanks for trying to help me. It's all a bit too confusing for me so I just decided to bite the bullet and send it into HTC. Thanks again!

bricked herald ??

hello could anyone help me ?
my device is stuck in bootloader and its recognized by the PC
this happened when i was trying a cooked rom
IPL 1.09.0001
SPL (ditto)
I searche everywhere an there seem to be only ways out for people with SPL 4.00.xxxx
is there a way out ??
thank you

sorry fr the bump but i really need help
I tried placing the phone in bootloader and installing the official HTC rom
but i get an ERROR 300
and the percentage is stuck at 0 on the screen

Try to flash your device with the Stock ROM.
That usually works

He already tried this, but it didnt work.
Let me just quote a post from dougstoner:
dougstoner said:
Well, yes and no. In the long run, it's better to Hard spl your phone. A lot of the roms in the forum require hard spl first. If you somehow fail during the hard spl, then you end up with a "brick". I used the uspl method first to flash, and it was a little easier to do, but hard spl'ing insn't complicated either. You just have to make sure of your ipl number is higher than 4. You can check this by holdign down the camera button, and press the soft reset button (use the stylus on the side to press) and continue to hold the camera button until you get to what's called the bootloader screen. It's red, blue, and green. Here are the instructions for hard spl, but MAKE SURE your ipl number is hight FIRST. If it isn't, you will brick your phone.
I case of people who don´t read 200 post and still brick their device - here is the guide that worked for ALL people with:
HTC P4350
XDA Terra
WING
with IPL 4.xxx and higher!!! (that is IMPORTANT)
and then follow this:
Default
For me it was working when:
1. install canonyang.cab
2. install aserpolicy.cab
3- install disablesecurity.cab
4. SOFTRESET
5. run RUU from Hard-SPLWM6 folder verison 4.70.yang
6. screen will become white - WAIT until it reboots itselfe.
7. done!
check if SPL now is 4.70.yang
Fore sure: I used this
http://rapidshare.de/files/38148213/...l_WM6.rar.html
mirror: http://www.sendspace.com/file/ot8zsn
It worked for many others, too.
Click to expand...
Click to collapse
So the IPL should at least be 4.xx but as you posted yours is 1.xx?! Might this be the issue?

Unfortunately, a SPL of 1.x after a hardspl/USPL means that the phone has been permanently bricked. Did you try to hardSPL your device or use USPL? They're both only compatible with 4.x SPL's.
I saw that someone recently came up with a way to fix bricked phones. They weren't Heralds, I forgot what they were... They basically found a way to use a buffer overrun on the SPL to launch code so they could launch a patched SPL and reflash... i wonder if our SPL's have that same bug and the method could be applied to us, too.

hey,
if my Herald is IPL 1.xxx can I somehow make it a 4.xxx? Or is there no chance to flash other roms? What does the IPL depend on? Production date?

thanks everyone for your patient replies
I guess for IPL 1.x there seems to be no solution as of now !!!
it was actually working initially with touch IT after Hard spl but i wanted to give a try to another version of touch it thats when the device got bricked .

I feel really sorry for you, but dont give up yet. As ivanmmj said, there could be a solution. Just check the forum.

I am not sure whether it helps but I did a little search and found severals threads:
Fix Bricked HTC ELF/ELFin
Someone with the same ERROR300 as yours
good luck

xtc.sanchez said:
I am not sure whether it helps but I did a little search and found severals threads:
Fix Bricked HTC ELF/ELFin
Someone with the same ERROR300 as yours
good luck
Click to expand...
Click to collapse
thanks so much mate !!! I will look into it right away

iv done all the reading
iv heard there was a way to flash the ROM through SD so i did try using
HERAIMG.nbh for the official rom from the HTC website !!
somehow the ROM does not work (invalid rom)
id try a couple of roms !!maybe ill be lucky !!
thanks again xtc.sanchez and everyone else
its been very informative and helpful

8125 bootloader stuck

ok, im inbetween a newb and a full out destructive force to any type of moddable device and im having a little bit of trouble with my cingular 8125. ive had this phone for a few months and i am having the hardest time dealing with the rom on the phone now. ill give a quick breifing on it:
got it with original cingular rom, not sure what spl or ipl on it but the first thing i did was unlock it by myself, cid and sim unlocked, and then updated to a jaguar wm 6.1 rom which worked fine. decided i was going to unfortunately sell this phone so i decided to upgrade it one more time to see if i really wanted to sell it, i then bought the upgrade to go past my 2.21 ipl and spl. i got my unlocker and followed my instructions and got a brick. but not a full brick. its stuck in the bootloader screen. after reading countless threads, i learned that i should be able to just still update a rom to the phone with no problems which actually works, but as soon as a rom completes it goes right back to my bootloader screen so help me! please cuz now thats its a challenge again, i want the phone! plus all my info is on the phone still back up

Flash the official stock ROM first, then use Button's ROM to downgrade your IPL and SPL before unlocking CID.

post the present IPL/SPL it displays now.Which rom you are trying to flash now ?

ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5

dimedash12 said:
ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5
Click to expand...
Click to collapse
WEIRD !
You got mixed Bootloaders of G3 And G4,IPL 2.21.0001 is G4 and SPL 2.21 is G3,as you posted,well,can't say which was original,only you can tell,but some how its mixed Bootloaders,in this situation no Rom will flash,its a 'Brick'.

If as Zabardast says its bricked then you have three options:
1. Get a new Wizard
2. Get a new Wizard Motherboard
3. Get a Wizard with broken LCD from eBay and replace its LCD with your current one and Enjoy!!! (Cheapest)

lol this is tough! but no worries, ill be back with some other pda at some point and time and then ill try and take this phone apart! but the weird thing about my wizard is that this only happened when i tried to update the phone with the CID unlock program that you have to pay for!
lol it was perfectly fine until i tried to do it! oh well, back to my crappy p168!

May be that CID Unlock program was not meant to be for a G3 and you were updating a G3 so it mixed you IPL/SPL and caused a kinda BRICK. So please be careful before doing flashing things because if you dont be carefull then your PPC may become a heavy paper weight, and a costy one too. LOL. TC

kitty4uhig said:
Farming for eq2 plat isn't easy, but you can buy eq2 plat, guides, accounts & items on sale. We have revolutionized the exchange of money to eq2 plat. Purchase eq2 plat& power up your character ot the next level. Our world class customer service will make sure you are more than satisfied with every purchase. Feel free to contact our 24 hour live support with any questions you may have. Shop now and play as a VIP!
Click to expand...
Click to collapse
Stop this nonsense immediately,otherwise it'll be reported and you'll be banned.Its spam !!!

try this: http://forum.xda-developers.com/showthread.php?t=276963

Cingular 8125 problems
Ok guys i am really pissed i have been looking for three days and cant find it, first off my IPL is at 1.01 and the SPL is at 2.25 and i cant fix it i wanted to install the original 2.25 again and start from scratch but can not find the damn thing so if anyone has it can u just upload it fo me and give me a link that i can get it at please i am sick and tired of waitnin i really like this phone and i dont want to risk bricking it thanks.

Ok, grimgod, aggression is reaaaallly ugly and no freakin one will help with that sh!t attitude (pardon the language, mods). The senior members do everything they can to help the noobs. Have you tried reading the flashing guide, wiki, or tutorial? I'd bet even money you haven't. Have you CID unlocked? Did you flash the button rom twice ( as the guide suggested to get ipl/spl both 2.xx)? Did you flash the official tmo rom (found im the flashing guide)? Have you done anything other than sit on your hands and wait for it to be handed to you? READ AND SEARCH!!!!!!!!!!!!!!!!

http://forum.xda-developers.com/showthread.php?t=310831 <HERE!!!!!!!!!! Should I flash your device, too?

Similar issue... need some Wizard Expertise
I picked up a coworkers old Cingular 8125 that he'd had in a drawer for about a year. Battery was right dead so the phone wouldn't boot. I charged the battery on an external charger for a few minutes, put it back into the phone, and plugged it in to the charger until the LED went green indicating a full charge.
When I power up I see the T-Mobile splash screen (light gray background, some square dots, and the "T-Mobile" logo). And there it stays indefinitely.
Tried a hard reset (Comm Mgr + Voice Cmd + Soft Reset), and it said "Press Send to restore factory default". Pressed the green dialer key (I assume that's send), and it says Format FAT partition, FAT partition complete, and then returns to the same T-Mobile splash screen and hangs there.
So then I tried putting it into Boot Loader manually (Power On + Camera). No problem, shows IPL 2.26 and SPL 2.26. Plug it into the computer USB port (running XP Pro), and then the USB connection shows on the phone. Attempted to flash the Wizard Love ROM to get this thing back to square-one. Error 260. Attempted to flash the T-Mobile stock ROM. Error 260.
Between each flash attempt, I'm pulling the battery out and starting fresh. I think I've followed all the steps I'm finding in multiple threads. But for some reason I'm not able to get this thing to communicate via USB. All RUU's give an Error 260. Am I missing something?

Forgot to mention I'm following the steps outlined in this thread from Dr P. To the letter!
Also did a little reading up on using the MTTY method in this thread by Drug_Store. Thought maybe the existing ROM might be intact, and I might be able get it to a 256MB MiniSD, then write the backup ROM from SD in boot loader. Well, for some reason I don't even see the USB connection option when I use the MTTY - can't ever get to a point where I can issue commands. Again, I think I'm following the instruction. But still no juice.

Nudge, nudge. I'd donate for a solution that works... otherwise I have to keep letting my 10 year old play The Quest on my phone.

help to unlock my tytn2 in uk orange network,

HI , friends i been trying to sim unlock my new tytn2 which is in uk orange network now.
I tried to install hard spl, i m new to this technical worlds like cooked rom, new hard spl etc ,.any one please tell me how to do this step by step,
When i tried to install hard spl, there comes a tricolor screen first white screen with progress bar 0% , and after some time it stucks and in pc shows error message. tried with jump spl method described by some one, in the kaiser section, what is the meaning of wm6 and wm6.1
Following are the details of my phone
R 1.27.12.29
G 22.45.88.07H
D 1.81.00.00
KAIS130
SPL-1.81.0000
CPLD-8
What should i do to get my phone unlocked, plz help i assure 5 pounds to the one who has time to help me in this. cheers friends.

WM6 and WM6.1 are Versions of Windows Mobile, see Settings, About on your phone.
Looking at the Radio version, you are a WM6.0 user still.
To install Hard SPL read here: http://forum.xda-developers.com/showthread.php?t=334679
If you get a white screen, read here: http://forum.xda-developers.com/showthread.php?t=354061
Once you have Hard SPL complete, you can SIM Unlock, read here: http://forum.xda-developers.com/newreply.php?do=newreply&noquote=1&p=2572785
I suggest you read here Getting Started and on the XDA Wiki, there is lots of information on the HTC Kaiser page that covers the basics.
It is appreciated to search and read before posting new threads when the information is already available. If you get stuck with one part, re-read the thread, search for your problem, and then (and only then) post in the thread you are trying to follow.
Thanks
Dave

thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.

pappoos4u said:
thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.
Click to expand...
Click to collapse
Try SSPL First, then JumpSPL 1.56, then JumpSPL 1.93. one should work.
Ta
Dave

pappoos4u said:
...i dont know what happens when i run jumpspl also it shows white screen no further actions takes place...
Click to expand...
Click to collapse
Dave's second link above says "If you get a white screen..."