Database Develop

Stuck at bootscreen after flash

I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?

Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again

easycure1974 said:
I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?
Click to expand...
Click to collapse
I am in the same situation now..
I am trying to re-flash the original ROM now, enter the booloader menu by holding voice-dial+CAMERA while resetting. then connect USB an try to re-flash.. It works for 30 minutes now without luck, I don't know what to do either... HELP!!
and a hint to those that are NEW: if you want to screw up your device, play with ROM upgrades... you will end up like us..

easycure1974 said:
Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again
Click to expand...
Click to collapse
PLEASE help me, what utility did you use to reflash?

Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked

easycure1974 said:
Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked
Click to expand...
Click to collapse
doesn't work form me because I didn't unlock before it crashed.. now I can't re-flash it..

ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.

easycure1974 said:
ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.
Click to expand...
Click to collapse
10x easycure, you are an easy cure for my troubles I am downloading it and I am sure it will work this time ( have a QTEK 9100)
Another question: did RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe upgrade your radio ROM as well? what machine do you own? I think of flashing it eventually as well..

I hope it will work for you!
Yes the t-mobile upgraded everything - but it has a lot of crap in the extended rom that I don´t like and with the new rom versions it doesn´t seem possible to delete anything from the extended rom.
So I will flash it again when a newer flash from qtek is available. Tried the Qtek_9100_1_6_7_ENG.zip rom but it is just OS - I dont like the idea of using OS from Qtek and the rest of the software from some other brand.
I have a swedish Qtek 9100

easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also

Priit said:
easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also
Click to expand...
Click to collapse
I tried that but I didn´t got the mms to work with that but then I shall make another try with that!

I installed Shortcut-MMS1-JAVA6XX-CV-VOICE-EmailWiz-TMO-03Nov05.CAB to get MMS support. I also installed coouple of CABs that had "Camera" in the name hoping it will improve camera functionality or something

Remove your Operator Splash Screen ;-)

Ok Friends, you hate the T Mobile Operator Splash Image ? I too.
It looks like http://img9.imagepile.net/img9/25963wm6_default.png
Flash with RUU NoId the nk.nbf file.
It remove only your Operator Image not your OS !
Have Fun
Let me know if you have better Images.
McSteff

Doesn't work for me, but thanks anyway
When I try this it comes up with ERROR [300] INVALID UPDATE TOOL
I have used lokwiz to CID unlock and SIM unlock but I still get this error.
Is there any way to apply this to my device?
Thanks

littld said:
When I try this it comes up with ERROR [300] INVALID UPDATE TOOL
I have used lokwiz to CID unlock and SIM unlock but I still get this error.
Is there any way to apply this to my device?
Thanks
Click to expand...
Click to collapse
My Phone is unlocked.
I set him in Bootloader Moder and run the RUU, it takes a few seconds and the new Operator Logo is flashed.
McSteff

have i understood this correctly?
does the image: http://img9.imagepile.net/img9/25963wm6_default.png become the operator logo instead of standard t-mobile logo, before wm5 or wm6 splashscreen come up?
and also no changes to OS are made - be that wm5 or wm6?
thanks for clarifying

anonymous1 said:
have i understood this correctly?
does the image: http://img9.imagepile.net/img9/25963wm6_default.png become the operator logo instead of standard t-mobile logo, before wm5 or wm6 splashscreen come up?
and also no changes to OS are made - be that wm5 or wm6?
thanks for clarifying
Click to expand...
Click to collapse
Yes, when you SoftReset it comes the new Logo, than Ipl,Spl.... and than the Windows Logo, but the stupid white T Mobile Logo is gone - forever ;-)
And there are no changes about your ROM, no Hard Reset !
It replaces only the Operator Logo.
McSteff

mcs said:
Yes, when you SoftReset it comes the new Logo, than Ipl,Spl.... and than the Windows Logo, but the stupid white T Mobile Logo is gone - forever ;-)
And there are no changes about your ROM, no Hard Reset !
It replaces only the Operator Logo.
McSteff
Click to expand...
Click to collapse
another question if i may?
how do i get the 'stupid white T Mobile Logo' back should i choose to? and by going back i would hope no OS features will be altered?
thanks

you will have to download the splash from internet, or someone could upload it to you, or... you could just perform a HR

anonymous1 said:
another question if i may?
how do i get the 'stupid white T Mobile Logo' back should i choose to? and by going back i would hope no OS features will be altered?
thanks
Click to expand...
Click to collapse
When you flash Aku 3 the T Mobile Operator Logo should be there.
McSteff

Hi, two questions.
1. Does this work when the phone is CID locked? my ipl and spl is 2.06 and can't unlock CID with lokiwiz which only works with 1.xx, and can't flash old ROM bacause most roms say upgrade only and the only one that i found that does not check this, crashes in Vista...
2. And also, I've had lots of problems running different RUUs on Vista (they crash). Do you know if this one does?
Thanks for your help.
Oh, and I have really cool Prince of Persia flash images. Attaching if anyone wants.

damac said:
Hi, two questions.
1. Does this work when the phone is CID locked? my ipl and spl is 2.06 and can't unlock CID with lokiwiz which only works with 1.xx, and can't flash old ROM bacause most roms say upgrade only and the only one that i found that does not check this, crashes in Vista...
2. And also, I've had lots of problems running different RUUs on Vista (they crash). Do you know if this one does?
Thanks for your help.
Oh, and I have really cool Prince of Persia flash images. Attaching if anyone wants.
Click to expand...
Click to collapse
1. Hmm, i dont know if it works on locked phones. My phone is unlocked and ipl/spl 3
2. Dont flash with Vista, RUU didnt work on this plattform, i´ve flashed my phone on xp.
McSteff

Finally it works!
Right, I have no idea why this has worked but it has. I have been trying to get rid of the TMobile logo for ages and I always get the Error 300 get a new update utility error.
What seems to have worked it applying the Radio rom update first (from Pedro12 - http://www4.turboshare.de/v/454059/X...61.21.rar.html) and then applying it.
I did this by replacing the nk.nbf rado file with the one from the splashscreen zip. I now no longer have TMobile on my phone, EVER! Thanks to the people in the community helping us to get the most out of these phones.
I think my phone is CID locked and yet am running WM6 (2.5) and no TMobile splash screen! I just now need to get a life....(!)

Fantastic! works first time! using latest Charmer WM6 ROM

mcs said:
Let me know if you have better Images.
Click to expand...
Click to collapse
Not better, but ... different. Could you do a version with just a black background, no image?
Cool.

Please HELP ME!! upgrade from bootloader

Hello, I've tried to upgrade my Qtek 9100 G3, the flashing finishing with success, but when I start the phone it doesn't load windows, I can see the splash screen, and then the screen become completely white.
I follow the faria instruction, and tried to install the wizard love ROM from bootloader screen, but I have error 300, "Strumento di aggiornamento non valido" that in english mean Update device not good..
Please, help me!!

finger roll said:
Hello, I've tried to upgrade my Qtek 9100 G3, the flashing finishing with success, but when I start the phone it doesn't load windows, I can see the splash screen, and then the screen become completely white.
I follow the faria instruction, and tried to install the wizard love ROM from bootloader screen, but I have error 300, "Strumento di aggiornamento non valido" that in english mean Update device not good..
Please, help me!!
Click to expand...
Click to collapse
1.- I don´t think you have a G3 because de IPL/SPL you posted, but is very strange that Wizard Love RUU reported such error in a G4
2.- What kind of upgrade you wanted to do?
3.- Reflash your original ROM if you have it available.

Mod edit: Please refer him to the wiki before posting such information.

Yes, I have a G4 phone, you can see on my sign, but my friend with the phone broken have a G3, and now he can install any kind of rom, the important it's that it works.

So.... problem solved?
finger roll said:
Yes, I have a G4 phone, you can see on my sign, but my friend with the phone broken have a G3, and now he can install any kind of rom, the important it's that it works.
Click to expand...
Click to collapse
Good for him! And how did he recover his phone? What did your friend do?

No he don't solved the problem, with any kind of ROM he's tring to install he get the same problem "error 300": invalid upgrade Tool!!
Please, do you have any idea?

Madcap180 said:
he has a G3 .. 2.17 I beleive is G3... Anything above 2.21 is G4 I beleive.
Click to expand...
Click to collapse
This is WRONG... PLEASE Don't post information like this unless you are positive of what you are saying as this could cause people to brick their phones.
Its explained in numerous places how to determine this, but this post is one of the best for overall information on determining your phone type and how to flash and recover from flash issues:
http://forum.xda-developers.com/showthread.php?t=298613

Madcap180 said:
he has a G3 .. 2.17 I beleive is G3... Anything above 2.21 is G4 I beleive.
Click to expand...
Click to collapse
Mine is a G4 (2.25.001) The trailing 0001 is what so far has identified a G4

when I was first trying to flash my phone I read anything 2.21 and above was a G4... so perhaps I READ the wrong information.

I got lost buddy
finger roll said:
No he don't solved the problem, with any kind of ROM he's tring to install he get the same problem "error 300": invalid upgrade Tool!!
Please, do you have any idea?
Click to expand...
Click to collapse
Could you provide the specifics of your friend´s phone?
* IPL / SPL (Current and original)
* Original ROM
* What ROM he was flashing when he got for the first time the white screen?

mfrazzz said:
This is WRONG... PLEASE Don't post information like this unless you are positive of what you are saying as this could cause people to brick their phones.
Its explained in numerous places how to determine this, but this post is one of the best for overall information on determining your phone type and how to flash and recover from flash issues:
http://forum.xda-developers.com/showthread.php?t=298613
Click to expand...
Click to collapse
The brick phone is a G3 with 2.26 IPL and SPL, from the T-mobile ROM. He brick the phone installing the prekitchen ROM from Faria.
Now Following the faria instruction, he would like to flash with wizard love rom, but he get the wrong update tool error. Did you know if there are some other possible solution?
In booloader mode, when I connect to the usb, in the phone screen appear USB, so I think that the phone it's not completely gone.

finger roll said:
The brick phone is a G3 with 2.26 IPL and SPL, from the T-mobile ROM. He brick the phone installing the prekitchen ROM from Faria.
Now Following the faria instruction, he would like to flash with wizard love rom, but he get the wrong update tool error. Did you know if there are some other possible solution?
In booloader mode, when I connect to the usb, in the phone screen appear USB, so I think that the phone it's not completely gone.
Click to expand...
Click to collapse
You´re right, if you have the tricolor screen and USB connection you´re safe, no worries!!! We can save it!
Have you tried the original T-Mobile? This one should do it, if you don´t succeed with the original ROM you may try Wizard Love but you have to use the right RUU, in this case pull de nk.nbf file from the Wizard Love and put it into the folder were the original T-Mobile RUU is (this would replace the original T-Mobile nk.nbf with the one from Wizard Love), then execute the original T-Mobile RUU with the new nk.nbf of course your Wizard connected to the PC, remove miniSD card (if any) and make sure you dissable the activesync connection
If my explanation sounds confussing for you, check this:
http://forum.xda-developers.com/showthread.php?t=294107
Good luck!

Thanks, I downloaded the T-mobile ROM, insert the love ROM nk.nbf and tried to upgrade...I get this error message:
Error 238: File Read
So, I extract the T-mobile, and launch the RUU directly, using the t-mobile nk.nbf, and not the wizard love one.
Now I'm flashing!!!!

Good for you!
finger roll said:
Thanks, I downloaded the T-mobile ROM, insert the love ROM nk.nbf and tried to upgrade...I get this error message:
Error 238: File Read
So, I extract the T-mobile, and launch the RUU directly, using the t-mobile nk.nbf, and not the wizard love one.
Now I'm flashing!!!!
Click to expand...
Click to collapse
Excelent!! I´m glad you had fix the problem!

Is my K-Jam totally bricked?

Is my K-Jam totally bricked?
It is now stuck up in bootloader screen.
I am able to swtch it off with power button. I can also have first flash screen.
On connecting with USB port, it shows yellow light indicating that it is charging & that over a period of time, goes green.
Earlier I had flashed TNT ROM but while reflashing newer it got stuck up as after flashing, I tried to hard reset [mistakenly thought ROM is flushed fully] & could not go further after initail first screen.
Other details:
IPL:2.16
SPL:2.16
GSM:02.07.10
O.S.:11.0.0.2
May some one help?
Thanks in advance.
Virat

Nopes ! its not 'Bricked' just had a bad flash. As long as it gets into bootloaders ,its perfectly safe. Perhaps,your phone is not CID unlocked ?
Download the official carrier's rom from its website and flash it in the bootloaders,it'll start to work fine.Then read the guide to cid unlock and upgrade.
Cheers!

boot issues
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.

ghumanfly said:
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.
Click to expand...
Click to collapse
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!

Thanks but solution found while reflashing in XP
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat

virat said:
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat
Click to expand...
Click to collapse
Thanks !
Glade you got it working
Have a nice day !

zabardast_1 said:
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!
Click to expand...
Click to collapse
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.

ghumanfly said:
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.
Click to expand...
Click to collapse
'Hard Reset' the phone,hope it'll work fine.
Well,I assume,you cudn't do the SoftSPL correctly the first time,try to apply the SpftSPL again correctly,if it works,ok,otherwise you can upgrade to wm6 with HardSPL method.

ba salam khedmate aghaye zebardast
duste aziz man ppc imate kjam daram ke eshtebahan soft spl kardam va rom wm6 prophet rush rikhtam ba tavajoh be inke seri gushi man g4 wizard bashe (ipl&spl 2.16.0001) kholase gushi alan tu safeye avali ke windows ba yek logo az rom marbuteh miad bala gir mikoneh .albateh 2 ta rom kjam asli wm5 ham gir avordam rikhtam vali hamunjuriye albateh jaye shokresh baghiye ke gushi tu halat bootloader gharar migireh va hard reset ham mishe. lotfan be man komak konid ta moshkelam ro hal konam. ba tashakor az shoma

could you please ,solve my problem kjam g4 wizard
laike salam brother
thank you very much for direction. I want to answer your question:
Quote:1. Which was the original official rom running on the phone before you tried to upgrade ?
1- I think wm5 belonge to 2005 becose it is written under the battrey.
Quote:2. What was the original wm5 rom and IPL/SPL of the phone before ?
2- I couldent remember but this phone approved by uaelab company [TA-2005/453 approved][E05/14/40225/g]and I flash with different official rom which you mentioned at ftp://ftp.clubimate.com but nothing happend ,maybe I do somthing wrong.
Quote:3.What exactly you mean you copied jumpspl to the root of the phone,did you applied SoftSPL ?
3- yes correct I did softspl with whit coulor screen then connected to pc and did toast that .
also I have problem to connect wst 4.2.2 to my ppc.
I download it and run, but the software couldent detect my fhone I dont know why .I connet it from bootloader 3coulor but nothing happen and so on.
could you please to explain how can I work with wst 4.2.2 also very important how to connect that because it says I have to connection with activesync .
pls direct me pls
mamnun
kourosh

kaiser not starting

ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......

gazzacbr said:
ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......
Click to expand...
Click to collapse
To Flash a ROM you'll most likley need Hard SPL
Follow the "Getting Started" Link in my Sig.
If you cannot get WM to boot, you'll need to re-flash your orginal carriers ROM.
Ta
Dave

thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?

gazzacbr said:
thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?
Click to expand...
Click to collapse
You shouldn't be using cmonex's SD method the first time round. It is for upgrading only.
I have downloaded the package from point 2 (you should follow the USB method in post 3, NOT the SD set) and have upload it onto my site, please let me know when you are done with it.
http://taeguk.co.uk/xda/HardSPL and CidUnlocker.zip
Ta
Dave

ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)

gazzacbr said:
ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)
Click to expand...
Click to collapse
Enter your bootloader and try flashing any ROM supplied by your carrier to get into Windows Mobile.
What screen do you get stuck on? If it is the tri color screen check out the link in my signature.
Ta
Dave

Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?

gazzacbr said:
Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?
Click to expand...
Click to collapse
No.
Can your phone boot into Windows or not?
Ta
Dave

Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id

gazzacbr said:
Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id
Click to expand...
Click to collapse
Yeah, you need the ROM your carrier supplied.
Where is the Phone from?
Does a Hard Reset help?
Ta
Dave

woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'

gazzacbr said:
woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'
Click to expand...
Click to collapse
That's right, flash the HardSPL 3.29 first (SIM unlock is optional, CID unlock isn't needed - Hard SPL takes care of that - but it comes as part of the SIM unlock) then flash a WM6.1 ROM.
Ta
Dave

gazzacbr said:
not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
Click to expand...
Click to collapse
Only if it's from the same region the RUU was intended for eg the European TyTN II's won't accept the latest Hong Kong WWE ROM by default because of this so as already suggested hardSPL works around this. My WM 6.0 UK original TyTN II upgraded to WM 6.1 OK but that was using the HTC UK provided ROM update. That updated everything required including the SPL and Radio to the required HTC versions. I'm back on the original WM 6.0 version though due to reliability issues with 6.1 and poor GPS performance.