Database Develop

My MDA Vario(Wizard) is almost dead!! Help please!

Hello,
Iám Spanish and I just bought a MDA VARIO in GErmany, so I tried to install the spanish rom "2.18.7.8" and i did it. Everything was ok during installation, but when I restarted... The device couldn´t restart. It allway stop on the Qtek screen(with the sky), sometime it change the screen into a white(HTC innovations) one for a second. But it doesn´t work.
I made soft and hard reset, but nothing changes.
I also tried to install an other rom by bootloader way, but the rom sais that is not possible to contact with the phone device.
I´m scared and I don´t know what to do.
Know this is the rom´s I have on my Qtek 9100 :
IPL 1.06
SPL 1.06
OS 2.18.7.8
Help please!!

Jmavatar said:
Hello,
Iám Spanish and I just bought a MDA VARIO in GErmany, so I tried to install the spanish rom "2.18.7.8" and i did it. Everything was ok during installation, but when I restarted... The device couldn´t restart. It allway stop on the Qtek screen(with the sky), sometime it change the screen into a white(HTC innovations) one for a second. But it doesn´t work.
I made soft and hard reset, but nothing changes.
I also tried to install an other rom by bootloader way, but the rom sais that is not possible to contact with the phone device.
I´m scared and I don´t know what to do.
Know this is the rom´s I have on my Qtek 9100 :
IPL 1.06
SPL 1.06
OS 2.18.7.8
Help please!!
Click to expand...
Click to collapse
With activesync on it will say it won't detect the phone plugged in while it's in bootloader mode. Run the ROM update anyway.

Thanks, but it doesn´t work. The Rom software said that is unable to connect with the phone.
I just tried to install the vanilla WM6, and with zhis rom, the installation could begin, but at 95% it happen an error... and i need to reinstal an other time the vanilla WM6.
I tried an other time, but the same error on 95% :-( And i can´t instal others rom.

did you CID unlock?
enter bootloader and flash the original rom from that screen, then start again. if you don't know how to get into bootloader screen or what CID lock is, read the wiki and the stickies in the forum. Don't worry, it is not a brick

bbobeckyj said:
did you CID unlock?
enter bootloader and flash the original rom from that screen, then start again. if you don't know how to get into bootloader screen or what CID lock is, read the wiki and the stickies in the forum. Don't worry, it is not a brick
Click to expand...
Click to collapse
Thanks a lot for our support! I still tnhinking I have a brick :-S... Now It only apears the bootloather screen(three colors bars) due to the incompleted vanilla WM6 uppdate.
I think the CID is unlocked. I runed the Lokiwiz, but now, I am not sure if It worked... And now, the phone is without battery!!
Where I can find my original rom? The device is from T-Mobile and is a MDA VARIO. From Austria. I have 2 CD´s, one with windows 5 applications, and other with software... I can´t fin the rom.
Thanks a lot!!

there is a link to the US tmobile ROM in my signature. it may work, i don't know.
as for the dead battery, you have a few options,
1) charge the battery in a desktop charger such as this one from ebay.
2) try charging in a friend's wizard
3) i have read references to charging the battery with a n-i-n-e v-o-l-t battery and a p-a-p-e-r-c-l-i-p (i've typed it like that because there are getting more and More references to things than actual solutions when you search) battery many times, try googling this site for that (again in my sig).
the ROM is not on any CD they give out with it because they don't want people flashing their devices and ending up in the situation you are - why do you think they are locked.

bbobeckyj said:
there is a link to the US tmobile ROM in my signature. it may work, i don't know.
as for the dead battery, you have a few options,
1) charge the battery in a desktop charger such as this one from ebay.
2) try charging in a friend's wizard
3) i have read references to charging the battery with a n-i-n-e v-o-l-t battery and a p-a-p-e-r-c-l-i-p (i've typed it like that because there are getting more and More references to things than actual solutions when you search) battery many times, try googling this site for that (again in my sig).
the ROM is not on any CD they give out with it because they don't want people flashing their devices and ending up in the situation you are - why do you think they are locked.
Click to expand...
Click to collapse
Thanks a lot!! But it doesn´t work. Error[294] Invalid Vender ID :S
I can charge the battery with the normal charger to 220v.
Any idea??
My IPL is 1.06
and SPL 1.06

did you buy it from tmobile or ebay? (is it german tmobile or just bought in germany?)
go to the tmobile site and look for firmware/software updates for the mda vario. i don't know german so i could not find the mda vario on it

bbobeckyj said:
did you buy it from tmobile or ebay? (is it german tmobile or just bought in germany?)
go to the tmobile site and look for firmware/software updates for the mda vario. i don't know german so i could not find the mda vario on it
Click to expand...
Click to collapse
I bought yesterday on a T-mobile shop from Austria. I downloaded it´s roms... but the same problem.
I will carry the device to the shop...
Thanks a lot!!

try this button rom
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
then have you followed the intructions in Dr Ps thread
http://forum.xda-developers.com/showthread.php?t=285435
do not give up

bbobeckyj said:
try this button rom
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
then have you followed the intructions in Dr Ps thread
http://forum.xda-developers.com/showthread.php?t=285435
do not give up
Click to expand...
Click to collapse
Thanks again, but I returned the phone to the shop. Something didn´t work since the beginning. Tomorrow I will reveive a new one...
Thanks an other time!

Hi,
I got a similar problem.
I wanted to install the latest AkU 3.3 on my MDA VARIO but it stopped at 95%.
So I tried to install the oldest version available from T-Mobile Germany.
But now my device restarts again and again.
It says
IPL 1.06
SPL 1.03
OS 2.24.2.8.
and restarts.
Sometimes (with the oldest software version) I can calibrate my touchscreen and then the device installs the T-Mobile software. After that it restarts again and again.
I also tried softrest after the message: in 3 seconds .... software will be installed. Then it reboots and sometimes wm5 starts but is running VERY slow. I can't switch it off using the power buttom.
I unlocked my MDA Vario using Lokiwiz. No CID Unlock just Unlock.
What can I do?
Thanks in advance

very simple, flash back to your original rom, then, CID UNLOCK

ROM flash gone wronge! help!

I was upgrading my t-mobile 8150(?) the k-jam with the new windows mobile 6 and in the middle of it my comp crashed!! now i am stuck at the bootloader mode (3 colored screen) and when i try to redo it i get to 99% and get a 302 error message. i follow the instructions given but keeps going in circles. its a G3 so is my phone bricked or is there a way to save it? i've been looking at this site all day but am now just more confused. lol thanks for your help!

No your phone isn't bricked. As long as you can get into the bootloader screen you should be ok. What you need to do is flash an official carrier rom either tmobile 2.26 or wizard love rom after you that than you can reflash to wm6. look at the stickies in the wizard forums that is where you can find these roms.

Thanks for the info but seems my techno curse continues. I tried the wizard love rom but it was in a different language and whem i tried the tmobile 2.26 i got "error 274 connection." Any more suggestions? Again thanks soo much for an issue I'm sure has been posted here a thouand times.

This happens to me all the time. I always use the Cingular 2.25 rom, it works perfectly and I have an I-mate K-JAM. Then, do the WM6 upgrade, but ensure all of your Norton and Antivirus and background running apps are shut down. Good luck.

yes also take out your mini sd card if you have one. even though its in another language it will work. "AVANTI means next. so just keep hitting that and you will be fine.

hmm been trying to d/l the Cingular 2.25 rom but the link seems to have stoped working...

It;s aaaaaaaaaaaaaaalllllllllliiiiiiiiiiivvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeee!!! for now lol Lets see what happens after i install wm6 I couldn't get the cingular rom but i had already dowbloaded the button rom i found here earlier and it worked like a dream!! quick and easy!! thank you all soooooo much!

hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?

flash to the tmo 2.26 or cingular 2.25...that will give you an IPL/SPL of 2.xx
then, you can flash to WM6

i want to delete this message. can't find a way to do it.

there's any other way to flash without usb cable?? sorry to bug in this thread but i lost my usb connection somehow and did a hard reset and still doesn't work. my phone charges. and no is not my computer cuz my wifes phone same as mine does sync i have a tmobile mda also known as the cingular 8125.

fallon75 said:
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
Click to expand...
Click to collapse
keep reflashing buttons rom until both ipl/spl are the same number. if they are different, then the flash didn't complete correctly. (it happens often, so it's kinda normal). just keep reflashing. after both ipl/spl are the same, then CID unlock and then update to an official carrier...then flash a wm6.

can anyone help me??

Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.

starkwong said:
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
Click to expand...
Click to collapse
it does shows but how can i flash?? it still won't connect o my pc. my pc doesn't recognize it. but it does recognize my wifes phone.

Try to run RUU straight with Wizard connected and running in bootloader mode

Dead Charmer... maybe

Hi all,
I tried to upgrade my MDA compact II (HTC Charmer) to WM6, but during the first step, downgrading to the "no vendor" version I made a mistake. A used a wrong version, it was for Prophet. After the final reboot, the device froze in the splashscreen "T-Mobile". After that I tried to do exactly the same with a "Charmer" version, but it didn't help me, the situation was the same.
However, now I'm able to flash successfully only the last vendor provided ROM update "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe", but it doesn't help me anyway, my Charmer is still freezing in the splashscreen. I tried to downgrade it , but the application gives the following error: "UPGRADE ONLY". When I try to make a hard-reset, and after that to confirm the factory settings by pressing "Yes" (green) button, the result is "Format FAT partition" and then "format is failed".
Only the bootloader is working now as well as the battery charging. Please, help me to turn back to the life my Charmer!
And one additional question: can I perform a CID unlocking just by ROM-flashing or the device must be fully operable?

Flash this:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
After that, you should be able to make hard reset. If you succeed, flash "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe" - that.

Hello there,
I am a new use an recently got an MDA PM200. I am in exactly the same situation as petrun. I have tried the flash suggested by vlodeck but it doesn't work, saying incorrect vendor ID (I guess that's because it's for a Prophet?).
What should I do next...?
Thanks.

OK, I succeed with a little progress. Many thanks to vlodeck, I will try to explain what happend...
I successfully flashed my Charmer with this Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Full link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
But it was possible only by using this "No ID" update application, not original one, maybe because my device is still locked:
Full link:
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
After that I succeed to format the FAT partition (finally ). But I cannot after all to flash the latest official MDA compact II firmware. There is two possible events, which I experienced:
1. When I try to use the original flashing application, I get the following response: "UPGRADE ONLY".
2. When I try to flash the official MDA compact II ROM, but through the "No ID" application, I get "INVALID COMMAND".
Just for explication, now my device cannot boot, it freezes in the splashscreen (it is Qtek now, not T_Mobile...) and the following versions could be read:
IPL 2.06
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
So, how I can do that? What should I do further? I would like to unlock my Charmer, but should I firstly make it operable?
Thanks in advance for your help, guys!

By the way, all described above I tried sevetal times with the same result.
The other thing is that... all links about the CID unlocking downloads, which I found here are no longer active. Any alternatives?

Rise from the dead!
Incredibly, but it's a fact! After successfull FAT formating I probably didn't wait long enough. Today I turned on my Charmer and several seconds after the splashscreen "QTEK" it successffully booted in WM5, performed all settings and finally started to work!
It's GSM module works, the Bluetooth works, I am able to start different applications. Just the camera does not work. And the most strange thing for me is that this ROM was for Prophet, not for Charmer
So, after all, how to proceed to upgrade to WM6? Now the bootloader is above ver.2.
Should I firstly flash it with proper ROM (for Charmer) or it's not necessary?
Should I unlock it as is now (Prophet ROM)?
Vlodeck, I rely mostly on you, since the WM6 with Touch FLO is your creation.
Thanks!

You dont have to CID unlock. Just flash that WWE T-mobile WM5 AKU2 for Charmer. Good luck.

Maybe I am boring, but steel need an advice: I cannot flash "WWE T-mobile WM5 AKU2".
1. The original RUU gives me "UPGRADE ONLY", maybe because my SPL after flashing the Prophet ROM is 2.20
2. This "NO ID RUU":
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
reaches 2% and gives "INVALID COMMAND", after that - only bootloader screen.
3. This "NO ID RUU":
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
cannot open the nk.nbf image (but works with other images), I don't know why.
What is the solution? Any ideas? Maybe some tool to downgrade the SPL to ver.1? I tried (it perhaps was bad idea)"RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship" and IPL became 1.12, but SPL remained 2.20... and Charmer didn't boot after that. After flashing the Prophet ROM it works again and IPL is 1.12, SPL is 2.20
In brief... how to flash successfully the last Charmer ROM?

If you cant flash the AKU 2 charmer rom, then go for AKU3.3 rom (can be german, that doesnt matter). Once done that, flash wm6.

Success
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!

petrun said:
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
Click to expand...
Click to collapse
WHERE I CAN GET BOUTH FILES cert_spcs.cab and enablerapi.cab
AND WHAT VIRSION OF PROPHET ROM SEND ME WORKING LINK THX DEAR

Charmer Stuck At Splash Screen
CHARMER STUCK AT SPLASH SCREEN
--------------------------------------------------------------------------------
I HAVE A MDA COMPACTII ''MADE IN TIWAN'' I WITCH WM5 I WANT TO UPGRADE IN TO WM6 SO I UPGRADE THIS WM6 TouchFLO Charmer WM6 ver. 2.1 FINAL by vlodeck AT THIS HOME PAGE http://forum.xda-developers.com/show...harmer+cert_sp... AFTER THIS I HARD RESET MY MDA C2 ITA ON BUT THE LANGUAGE IS NOT ENGLISH I CANNOT UNDERSTAND ....
SO I CAN REFLASH IT WITH THIS ROM Charmer_Touch_GER_Beta_2.7 .. AFTER FLASHING COMPLETE I SOFT RESET MY MOBILE.
SO MY MOBILE STUCK ON SPLASH SCREEEN ONLY T-MOBILE IS SHOW
MY MOBILE DETAIL IS AS UNDER
IPL 2.06 .0001
SPL 2.06 .0001
GSM 02.19.21
OS 4.0.0.0
PLZ DEAR SIR WHAT IS SOLUTION OF MY MDA C2
MDA2 CANNOT CONNECT WITH ACTIVE SYNC

Of course it cannot connect with ActiveSync, the device doesn't boot. One certain solution for bricked Charmer is Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Use this link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
In order to flash this, you should enter the bootloader, without using the ActiveSync. After that try to perform a hard reset, you probably will succeed to format the FAT partition.

if you cannot connect the pda to pc HOW CAN U PUT THE ABOVE PROPHET RUU ON CUREENT?

I have a charmer and I was trying to update to wm6. I can´t because the ipl is 1.12. I updated rom to german aku 3.3. But I can´t hard reset. format error. I´m trying to put prophet rom to format it, but when I send the prophet rom, it always give me an error at 95%. error 326 - this nbf file cannot be used fo your pda phone. please check your nbf file. the aku3.3 rom flashes ok. any idea?? I try tu send a radio rom. after that is the same. 95%error. please help. I can´t bring my charmerback to life.

Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!

Yallah said:
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Click to expand...
Click to collapse
same problem here... any suggestions or is my charmer bricked?

Charmer dead. any solution?

have a charmer. I tried to put wm6. but spl and ipl was 1.12. the phone start up and hang when installing some cabs. i restart ir and it allways crashes at t-mobile logo. i updated the rom to aku 3.3. all ok. but continues chashing on t-mobile logo. i try a hard reset. gives me a fat error. I try to put the rom from prophet to try to format it. but that rom upgrade reach 95% and stop. give me a error. this nbf file cannot be used to upgrade this device. I tryed all types of roms. most of them crashes at some point and give me that error. the rom aku 3.3 german and wwe, install perfect. I think that is the only roms I can send to my charmer. but i can´t format whith that rom, fat error. I have 3.08 spl ipl 1.12 because i sent an old charmer rom. ipl downgrade, but spl don´t. do you think my device can be protected?? I dont know that to do more, to bring the charmer back to life. will sd card method work? please help me.

Charmer dead after wm6 update whitout cid unlocking
Hi @all
i have the same problem.
iam stuped and make an wm6 update from ipl1.12 and i have forgot to cid unlock my charmer.
after the update to wm6 all looks like good. the bootscreen from wm6 i have see.
after the reset the charmer hangs at slashscreen.
now i make a update to aku 3.3 ger.
that works but hangs in the t-mobile spaschscreen.
i have tray all downgrading methodes i have read here but nothing works.
jet i have a ipl 1.12. and spl 3.08.
I think only a sd-card rom update works. but i dont have found an sd-card rom to use.
sorry to my bad english.
please can anybody help me?
cu AxelD

Is my phone already dead? Please help me!
Hi, I have a similar may be the same problem!
My phone is a German t-mobile mda compact 2
First I work with “lokiwiz v.02” to unlock the SIM, and it works really well.
Then I installed “Charmer_Touch_ver._2.1” and I could calibrate the screen, and after that Win Mobile 6 installed all the extra stuff automatically. After that the device made a reboot, but it stop at the t-mobile boot screen.
Because the bootload modus is still running, I installed the newest original t-mobile software “RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship” but this also didn’t solve the problem.
Hard reset didn't work and always says "Format is
The Start screen shows me this information:
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.22
Is my phone really dead or could someone tell me a trick to reactivate it?

I think noone have a solution for us. I tried to send commands to phone whith mtty. and I can´t send. I don´t know why. so f we cannot send commands the sd card method will not work too. the only olution is to jtag the charmer. but can´t find any pinout information. if anyone knows this informtion, please help.

Bricked Wizard

sorry if this post seems to be a repeat , but i tried the search option and the results were not fruitful
a friend of mine , while trying to upgrade to a TNT ROM , didn't HardSPLed the device first , and successfully changed the ROM of the device , now it is stuck on the blue screen with SPL and IPL versions , and no response . for some reason , the device can go to bootloader mode , but it can not be reflashed , and it does not respond to a hard reset command.
please advise on what to do
regards

When it is in the bootloader mode, and connected via USB, is there a little USB icon in the bottom left? If so, simply flash your phones carrier ROM and all should be fine with it again. You can then apply HardSPL and flash to the TNT or any other ROM that you want to. Is your device a G3 or G4 by the way? What are the numbers after IPL and SPL?

well my friend says that the USB icon is visible there , and the device was indeed a G4. the thing is , what exactly should he do , in order to flash the ROM , since non of imate roms work for it. should he use any special software?
i'll greatly appreciate your help

Is he using Vista or XP?

he is using Windows XP , could it be the PC OS that caused interference?

Well, only if it is Vista does it really matter. He needs to get ahold of an original carrier ROM, such as the O2, or T-Mobile one and flash it to his phone, then HardSPL it, then upgrade to 6 or 6.1.

Download and flash Wizard_love Rom,it might do the trick,then HardSPL and upgrade to any wm6 or 6.1 rom.
What exact error it gives while flashing imate official rom ?

well the wizard has been an imate ,and it was flashed with an Original imate ROM already , but no success , any other suggestions?
thanks again

error [294]invalid vendor ID :
This Update Utility can not be used for your PDA phone.Please check your update utility.
here is the picture
http://i35.tinypic.com/29v03rl.jpg
and could you please give a link to the Love ROM?
thanks

Download wizard_love Rom from this link:-
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar

well he first got this error while upgrading
http://i33.tinypic.com/ivjz8o.jpg
then he managed to upgrade , but had the very first screen after ugprading on PPC screen , and nothing happens
it also gives a failure message while trying to manually Hard Reset after upgrade
please advise on what to do next
greatest appreciations

No SD Upgrade even tough... MTTY hahahaha
king_dani said:
well he first got this error while upgrading
http://i33.tinypic.com/ivjz8o.jpg
then he managed to upgrade , but had the very first screen after ugprading on PPC screen , and nothing happens
it also gives a failure message while trying to manually Hard Reset after upgrade
please advise on what to do next
greatest appreciations
Click to expand...
Click to collapse
It seems you need to follow the drugstore MiniSD upgrade but...
I guess you dont have another wizard to make a bacuk up... so wait a minute...
You don have hardspled yopur device...!!!
HAHAHAHA forget it!mmmm
Maybe mtty... folow mi signature maybe works
See you There Men!!!!