I posted a question last week and I was installing the ROM and windows crashed. My phone now has the bootloader screen (colored screen with USB in the corner). I had already upgraded to 2.17 which was fine. Any thoughts?
If you can still access the bootloader you have not fried your phone. Get it into bootloader - plug in your USB and connect to your PC and run the ROM upgrade again. If it fails again check the ROM is a good version ( re-download if your not sure) Failing that, do the process on a different PC.
BTW you do not need to run Activestink on the PC.
Best of luck :lol:
Related
Hi folks,
Very strange: I tried to connect to the PC with ActiveSync 4.1 and the BA in the bootloader mode. Didn't connect. Tried a couple of times, reinstalled AS etc. No chance.
Therefore I wanted to be sure, there is no connection problem, I started the MAUpgrade tool, which connected successfully and showed the EPROM versions on the screen. So I started the upgrade procedure, as expected the BA went in the bootloader mode, but as before, from there nothing went on - it was not recognised by the PC or AS.
The strange story about it is, I connected very easily in the normal mode, I upgraded already in the past successfully ...
BUT NOW I'm really in trouble, because I can't exit anymore the bootloader mode. I tried a hard and soft reset, I have removed the battery for 10 minutes .... Now way, the sceen is always in bootloader. If I put the device in the cradle, it recognizes this, by showing USB, without cradle, its Serial. The bootloader shows the version 2.08
Shoud I replace the device and enquire with my provider for a new one?
Thanks and looking forward to hear from you, Alexander
I have a wierd problem that I haven't seen discusssed here before. My PC runs Vista and has the Windows Mobile Device Center software on it. When I plug the phone in to a USB connection cable to try and flash a new ROM, the phone is recognized. When I start the ROM updater program though, suddenly the phone is "disconnected" (no longer shows as connected and dissappears from the listing of attached devices in My Computer also).
So, the ROM Updater says it cannot find the required file. How can I get the phone to stay connected long enough to run the whole update processs?
Try to put it into bootloader before flashing.
First of all check out the Hermes wiki about Vista flashing.
Second. Try to put your device into botloader mode, then run the flash. This works for me everytime.
Cheers,
Chris
I flash from Vista Ultimate x64 without issue.
NotATreoFan said:
I flash from Vista Ultimate x64 without issue.
Click to expand...
Click to collapse
Same here. However, for ROM flashing I suggest flashing from the SD card. It's safer and quicker. Read up on it here: http://forum.xda-developers.com/showthread.php?t=336158&highlight=flash+sd+card
I've reading some FAQs and Wiki articles before make this question.
Last weekend my Kaiser crashed into the floor (a very very very soft fall) and the battery jumped out the phone.
I put the battery, and in the first boot.... Ooops!! Tricolor screen showing:
"Hardspl 3.29
Serial "
There is a quick splash screen showing "No image file".
I've tried to boot several times, and i get into OS once, but the pda works so slow.
Solutions that i've tried:
a) MMTY prompt. Boot command doesn't work and i dont know the "boot command" for Hardspl 3.29. Anyway, i dont want to mess with MMTY and get a brick...
b) When i get into OS i tried to connect via Activesync (to reflash Hardspl) but...
After JumpSPL I get "Jump Tricolor Screen"
I unplug usb, uncheck "USB Connections", plug USB... but KaiserKustomRuu doesnt work! It closes after executing it. (The day that i flashed hardspl 3.29 i did it the same way, and everything went ok)
What can i do?
Please help!!!
(I dont care loosing data, i only want recover the pda)
EDIT:
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
EDIT 2:
Ok.... i've tried to access MTTY prompt but it was impossible.
When i plug the USB cable i get an error in the computer (device not recognized), but PDA screen changes between "serial" and "usb".
After 20 or more tries i got into MTTY prompt, but that was the last time until now.
So... i think that mi usb port is broken ( is not the cable or the computer, i used some cables and computers)
I've tried to move the usb connectors with a pin, slowly, and i have cleaned evertything, but nothing happens.
What may i do?
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
So you are unable to use activsync at all on your phone?
http://forum.xda-developers.com/showthread.php?t=423486
Hi there.
Yes, i am unable to use activesync from OS.
Draelee, i will check that thread, thanks.
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
UPDATED the first post.
Is my PDA - USB port broken?
I hate to tell you this.. But a work around could be to Activesync via Bluetooth... Now a days you can get a USB Bluetooth dongle for $5 or sell... My stepsons USB port is so broke that he has 3 batteries and a stand alone battery charger.. he jsut swaps batteries when it dies... He syncs via bluetooth and has no problems....
So, once you have read the entire post...
Do you think in a software or an hardware problem?
Bluetooth sync is a good option, but i would like to investigate a little.
I've reflashed HardSPL, ROM and RADIO but i think that there are more bad data sectors.
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
Thanks!!
Try flashing an Android ROM
Hi,
I had the same problem on my phone for about 6 months. I completely gave up on it. A few days ago I successfully flashed an Android ROM to NAND but ended up flashing back to WinMo. Surprisingly my USB activesync / headset adapter started working again!!
I'd give it a shot if I were you. Worked for me
~Joe~
About a year-ish ago windows stopped working on my spv3600 m700 Trinity. I looked into reflashing the phone & put a copy of schaps 4.30 striaght onto the fone no problems.
I now want to upgrade the rom again & can get it into the bootloader screen ok. My problem is that this is as far as I can get. I've even tried the minisd trick but I see loading box very briefly flash up on the screen & thats it...still in bootloader mode with serial but nothing else happens.
The fone is not bricked & if I reset it will load windows. I've tried the original flash & bootloader. Soft (SSPL) & hard Bootloader technique but to no avail.
Has anyone got any other solutions? Many thanks in advance, its sending me crazy!!
Ok I sorted the first problem of using SDcard to flash .MBH files. It was down to the miniSD card format not being FAT32. I reformat the card as FAT32 & then bootloader progressed to installation stage.
...now I have a new problem... i'm stuck in bootloader mode SPL 1.07.0000 IPL 0.50 after I used SSPL from my mobile in windows mode to get the 1.07ds override bootloader. This allowed me to flash the Radio to the latest chinese version. I then used this program again to Flash to windows 6.5 & then half way through it rebooted to the bootloader tricolour screen.
The problem is that now that windows is gone I can only run the standard bootloader SPL 1.07.0000 with the phone. If I try & upgrade a cooked ROM it comes up with an error code on the mobile. If I try an official version it checks the ROM & then says "not allowed".
Is there a way I can change the bootloader through the card SD? I can't either get the bootloader to change from serial msg to usb...doesnt matter how many times I plug in the USB & i'm using XP. Is there a way to force it into USB?
I've tried putting "Des crash proof SPL" ,"Hard SPL", "Hard SPL 1.20" onto SDmini card as TRINIMG.NBH bootloader loads then comes up with 00068002 error i presume on screen
I've tried putting official upgrades "RUU Trinity DOPODA SIA WWE...Ship.EXE rom" & "RUU Trinity HTC WWE .........GPS.exe rom" onto SDmini card as TRINIMG.NBH, bootloader loads, . . .checking, then displays "not allow" & "00028002" on screen! Now i'm really stuck!
Any help would be greatly appreciated!
looks pretty much the same like my trinity right now...
help would be very appreciated
Solved.
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Still on bootloader with error 0068002
can't ran anything.
Please help......
SOLVED:::::::: sorry
Trinity bricked , pls help ...
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Hi , there ,
I am finding myself into the same situation but I do not realy get you : how You managed to get out of the bootloader mode where it says :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Can you , pls, be more specific , cause I am a newbe who bricked his Trinity a week ago :::
Blocked with error 0068002
Hello, after I install nAr.23016.FRA.IE8-CHOME on my sfr s300+, I'm blocked on the first page HTC, etc...When I put the S300+ under bootloader (photo and power button action), I plug the USB and I itry to flash;result is a reboot. I try with TRINIMG.NBH and result is error 0068002.
I need help to resolve this problem.Can u help me? Regards.
dan (excuse my bad english)
Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?