Related
[SOLVED! See page 4]
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((
Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?
I think it was 2.26 (it may have been something like 2.27....), but it definitely didn't have the .000 at the end. I thought that the Wizards without the .000 were G3. Did I screw up?
Madcap180 said:
Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?
Click to expand...
Click to collapse
2.25.0001 or 2.26.0001 would be a G4
2.25 or 2.26 would be a G3
MacGuy2006 said:
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((
Click to expand...
Click to collapse
I thought I read somewhere that IPL/SPL 3.08 was a bad convert from a Charmer? If this is true and the Charmer bootloaders are different than the Wizard bootloaders then you may have put yourself in a bind.
The fact that you can still get past bootloader is promising even though the phone doesn't finish booting.
Try flashing from the bootloader (tricolor IPL/SPL screen with USB in the corner)
Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?
MacGuy2006 said:
Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?
Click to expand...
Click to collapse
You CAN'T use shelltool in boot loader mode! it needs the OS and the TRUFFS to read and write to the phone.
Any phone that doesn't go past the boot loader must be fixed with mtty, RUU or SD card...
Thanks for the info. I've been reading about mmty and just downloaded it. But I only have a 4GB card handy (from my Trinity.) I might be able to find my old 2GB one at home.
Edit: Well, this is what I just found: http://forum.xda-developers.com/showthread.php?t=308772&highlight=mtty+wizard
It seems that the IPL_SPL 3.08 might be a real problem. I'll try the card flash, but based on the above thread, I am not holding my breath.
If anyone has a suggestion or a solution, please let me know.
Thanks!
BTW, if the problem is indeed with the IPL_SPL 3.08, then perhaps the suggestion that we upgrade to it (in red) here http://forum.xda-developers.com/showthread.php?t=285435 should be removed, so that we don't get more expensive bricks.
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
After I unlocked my wizard and before I try any new ROM, I always burn the latest German wizard ROM with 3.08 IPL/SPL "ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship". Then I downgrade the Radio ROM to Cingular 2.25.11. Then I burn my ROM of choice. I've found it works best for me. I've never had a problem with 3.08.
TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
What are the grounds for such a comparison? How to tell that an SPL works better than another? As far as i know the SPL is there to initialise the hardware and to apply security restrictions.
What i'd like to know is if anyone has been successful in downgrading IPL/SPL from 3.xx to 2.xx as itsme once said that there was a security in newer SPL's preventing downgrading (i must look for it...)
cheers
O.K., so maybe it's not 3.08, but something has sure gone bad.
I am trying to use mtty 1.1.42.538, but see only Port 1, Port 2 and USB. When I type in \\.\WSCUSBSH001 I get a message that it cannot open the \\.\WSCUSBSH001 port.
I tried resetting as described in message #7 here http://forum.xda-developers.com/showthread.php?t=264652&highlight=mtty1.42, but nothing happened.
I also tried choosing USB, then typed in r2sd all and again, nothing happened - I just get CMD> again....
So, can anyone think of anything else I can do, or should I just drop it from the 4th floor?
What IPL/SPL values you have at this moment?
mestrini said:
What IPL/SPL values you have at this moment?
Click to expand...
Click to collapse
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.
MacGuy2006 said:
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.
Click to expand...
Click to collapse
I had also upgraded my IPL/SPL to 3.08 -- up from the 2.25 on the newest Cingular ROM.
Anytime I've flashed to a WM6 ROM, I've been able to downgrade to the T-Mobile 2.26 ROM -- which changes the IPL/SPL to 2.26 -- with no problems before upgrading to a WM6 ROM. After flashing the WM6, I then go back in and upgrade the IPL/SPL once again to 3.08. It's not failed me yet.
O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?
MacGuy2006 said:
O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?
Click to expand...
Click to collapse
If I were you I might be talking to IMEI unlockers. Their process works from bootloader and might be able to get you CID unlocked and fix your corrupted CID area, which seems to be your major problem atm. In any case I would contact them and explain your situation and see if they think their software will unlock your phone. If so then you should be good to go once you CID is "uncorrupted" and unlocked.
one question: can You HARD RESET your device?
Do you have "format failed" message?
if so, you have 50/50 per cent for resurrection.
3.08 is not direct problem here anyway..., version is not exactly matter of problem...
(imei? now? lol)...
Thanks!
Yes, I can hard-reset fine and it claims to reformat fine.
Tx for the suggestion - I will contact IMEI (they unlocked my Trinity before the free unlockers were available
I was upgrading my t-mobile 8150(?) the k-jam with the new windows mobile 6 and in the middle of it my comp crashed!! now i am stuck at the bootloader mode (3 colored screen) and when i try to redo it i get to 99% and get a 302 error message. i follow the instructions given but keeps going in circles. its a G3 so is my phone bricked or is there a way to save it? i've been looking at this site all day but am now just more confused. lol thanks for your help!
No your phone isn't bricked. As long as you can get into the bootloader screen you should be ok. What you need to do is flash an official carrier rom either tmobile 2.26 or wizard love rom after you that than you can reflash to wm6. look at the stickies in the wizard forums that is where you can find these roms.
Thanks for the info but seems my techno curse continues. I tried the wizard love rom but it was in a different language and whem i tried the tmobile 2.26 i got "error 274 connection." Any more suggestions? Again thanks soo much for an issue I'm sure has been posted here a thouand times.
This happens to me all the time. I always use the Cingular 2.25 rom, it works perfectly and I have an I-mate K-JAM. Then, do the WM6 upgrade, but ensure all of your Norton and Antivirus and background running apps are shut down. Good luck.
yes also take out your mini sd card if you have one. even though its in another language it will work. "AVANTI means next. so just keep hitting that and you will be fine.
hmm been trying to d/l the Cingular 2.25 rom but the link seems to have stoped working...
It;s aaaaaaaaaaaaaaalllllllllliiiiiiiiiiivvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeee!!! for now lol Lets see what happens after i install wm6 I couldn't get the cingular rom but i had already dowbloaded the button rom i found here earlier and it worked like a dream!! quick and easy!! thank you all soooooo much!
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
flash to the tmo 2.26 or cingular 2.25...that will give you an IPL/SPL of 2.xx
then, you can flash to WM6
i want to delete this message. can't find a way to do it.
there's any other way to flash without usb cable?? sorry to bug in this thread but i lost my usb connection somehow and did a hard reset and still doesn't work. my phone charges. and no is not my computer cuz my wifes phone same as mine does sync i have a tmobile mda also known as the cingular 8125.
fallon75 said:
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
Click to expand...
Click to collapse
keep reflashing buttons rom until both ipl/spl are the same number. if they are different, then the flash didn't complete correctly. (it happens often, so it's kinda normal). just keep reflashing. after both ipl/spl are the same, then CID unlock and then update to an official carrier...then flash a wm6.
can anyone help me??
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
starkwong said:
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
Click to expand...
Click to collapse
it does shows but how can i flash?? it still won't connect o my pc. my pc doesn't recognize it. but it does recognize my wifes phone.
Try to run RUU straight with Wizard connected and running in bootloader mode
Hello all,
I am somewhat of a newby here, but I have successfully unlocked my Cingular 8125 and installed a couple of WM6 ROMs. I followed the procedure of downgrading to Button 1.05 ROM, then running Lociwiz, then installing T-Mobile 2.26, then WM6 ROM. Worked great...until now.
I was going to try another ROM, and I followed above procedures (didn't know if I needed to after initial unlocking, but I did anyway). At the "install T-Mobile 2.26" step, after 1 %, I got an error 326?, nb file not for this device. I can still install cooked WM6 ROMs, and the SPL changes, but IPL always remains at 1.01. If I try to install IPL/SPL 3.08 CAB, SPL changes to 3.08, IPL stays at 1.01. I have re-installed Button Rom 1.05 and run Lociwiz a dozen times to no effect. Even the Cingular WM5 OS meant for this device gives me the same error code as the T-Mobile.
I'm hoping this is a simple newby error. Anybody have any suggestions.
Thanks for any help.
By the way, after loading Button ROM, my Wizard hangs during the customization routine at Signed_DiscoButton8.sa. I must soft reset.
I got exactly the same problem.
I am now on IPL 1.01 , SPL 3.08, radio 2.69, using rom NBD 8.3
doesnt seem a problem however...
d-lite said:
I got exactly the same problem.
I am now on IPL 1.01 , SPL 3.08, radio 2.69, using rom NBD 8.3
doesnt seem a problem however...
Click to expand...
Click to collapse
Hey m8,
have you forgotten this thread (http://forum.xda-developers.com/showthread.php?t=319582) ? (see last post)
mestrini said:
hahaha nice to see good spirit after all this
Here goes:
Make backup of the CID block (VERY VERY important!!!)
Make backup of the GSM calibration block (VERY VERY important!!!)
Kill wcescomm.exe process
Start mtty, enter bootloader mode in Wizard and connect
type doctest (this will write test patterns in DOC chip and clear all data!)
Flash button ROM (1.01_IPL/1.01_SPL/1.05_OS)
Flash CID block backup (don't miss this)
Flash GSM calibration backup (important)
If all ok then remember to upgrade to 2.xx before installing WM6!!
Post results
EDIT:
Use WST for steps 1, 7 & 8
Click to expand...
Click to collapse
are you willing to prove me wrong?
mestrini said:
are you willing to prove me wrong?
Click to expand...
Click to collapse
yes.. missed your last post to be honest, sorry..
(btw phone is happy till now .. but we go for solving it, killing seems impossible)
step 2, gsm callibration block.. how do i copy?
D-Lite
use the "Read ROM" button and select the appropriate section from the list.
status:
Code:
DOC ImgFS partition read/write test PASS
Ext ROM partition read/write test, offset=0x0, length=0xA00000
Test pattern =0xAA
Flash Ext ROM failed.
DOC Ext ROM partition read/write test FAILED
--Flashing button rom @ 100%
--DATA CRASHES PLEASE CONTACT SERVICE CENTRE
--WST Says I am still on SPL 3.08 and rom is write protected.. screen of wizard says SPL 1.01 ...
--Installing Button ROM, ... SIM Lock SUDDENLY
--Screen goes funny flashing between simlock and customise
--Few soft-resets, WST now convinced on SPL 1.01 and flashed CID block
--Soft-reset
--Imei gone, flashed back GSM callib. data, softreset
--doesnt boot passed the pint of beer... going for RUU of T-Mobile 2.x
--bootloader, flashing RUU_Prodigy_2210205_22102108_021911_TMO_NL_DUT_Ship.exe
--The NBF can not be used for your phone @95%, followed by congratiolations (stupid software)
--trying UK version...
--all give error 326
--another button flash
--*PLING IDEA* on 3.08 i couldnt doctest properly... so doing it again
-- bad idea.. same result...
damn... i thought it would work
anyway, there was point where the phone had same values for IPL/SPL (not too bad ). What is strange is why phone didn't boot anymore after flashing the GSM calibration and saying the flashes weren't suited for the phone.
What state is it on now? Wanna go again? This time, instead of flashing the 'GSM calibration data' do a simple IMEI writing and try to unlock CID before upgrading to official ROMs
sorry for this...
IPL locked on 2.26
I am having the same issue. I have tried numberous times to load my original rom and get the 326 error @ 1%. My ipl remains locked on 2.26. Is there any way to fix this? Please help.
it is now on 1.01, got my own imei back, spl 3.08, nbd 8.x rom...
everything fine again.. pretty sure it has something to do with ext.rom and/or write protection of it.. will give it another shot but not this month.. getting busy
@acmickey, not sure if you got same issue... is your IPL 1.01? else you might just have a locked phone..
Hey d-lite,
I followed your example and loaded BSD8.3 ROM and IPL/SPL 3.08 and radio 2.69. Everything seems to be fine. No missed calls. All programs work (touchflo is pretty cool). IPL is still locked on 1.01, even though SPL is 3.08.
I tend to agree with you that something is suspicious concerning the extended ROM. The first symptom I had that something was wrong was after loading Button's ROM, during the customization routine, Signed_DiscoButton8 would not install. Phone locked up and had to soft reset.
Oh, well, at least the phone works. The downside, of course, is that you can't load an original ROM, even though you can load a cooked one. Weird, huh?
Hopefully someone a lot more knowledgeable than I will figure this one out soon. Will keep checking the boards. At least we don't have bricks.
I am having the exact same problem as the 1st post but my ipl is stuck on 2.26. I am using an unlocked device and I have no problem downgrading/upgrading the spl. I also get the 326 error when I try to flash back to the original rom. (I used to be able to do this without a problem - I can't figure out what happened.)
It's really weird and I have search and searched and can't seem to figure out a solution.
which SPL you have now?
sorry.... my spl is 1.01
Right. Assuming your device is working 'normally' are you willing to try something new? If so contact me PM
what have you cooked up this time mestrini? lol
my wiz (at 1.01 still..) is doing a-ok, but always willing to go for something new so we can fix this for the communities sake...
d-lite said:
what have you cooked up this time mestrini? lol
my wiz (at 1.01 still..) is doing a-ok, but always willing to go for something new so we can fix this for the communities sake...
Click to expand...
Click to collapse
sorry to mislead you buddy but acmickey got it all wrong and, instead of IPL stuck at 2.26 and SPL 1.01, he has same as you IPL 'locked' at 1.01
So my theory could not be verified.
cheers
ok, im inbetween a newb and a full out destructive force to any type of moddable device and im having a little bit of trouble with my cingular 8125. ive had this phone for a few months and i am having the hardest time dealing with the rom on the phone now. ill give a quick breifing on it:
got it with original cingular rom, not sure what spl or ipl on it but the first thing i did was unlock it by myself, cid and sim unlocked, and then updated to a jaguar wm 6.1 rom which worked fine. decided i was going to unfortunately sell this phone so i decided to upgrade it one more time to see if i really wanted to sell it, i then bought the upgrade to go past my 2.21 ipl and spl. i got my unlocker and followed my instructions and got a brick. but not a full brick. its stuck in the bootloader screen. after reading countless threads, i learned that i should be able to just still update a rom to the phone with no problems which actually works, but as soon as a rom completes it goes right back to my bootloader screen so help me! please cuz now thats its a challenge again, i want the phone! plus all my info is on the phone still back up
Flash the official stock ROM first, then use Button's ROM to downgrade your IPL and SPL before unlocking CID.
post the present IPL/SPL it displays now.Which rom you are trying to flash now ?
ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5
dimedash12 said:
ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5
Click to expand...
Click to collapse
WEIRD !
You got mixed Bootloaders of G3 And G4,IPL 2.21.0001 is G4 and SPL 2.21 is G3,as you posted,well,can't say which was original,only you can tell,but some how its mixed Bootloaders,in this situation no Rom will flash,its a 'Brick'.
If as Zabardast says its bricked then you have three options:
1. Get a new Wizard
2. Get a new Wizard Motherboard
3. Get a Wizard with broken LCD from eBay and replace its LCD with your current one and Enjoy!!! (Cheapest)
lol this is tough! but no worries, ill be back with some other pda at some point and time and then ill try and take this phone apart! but the weird thing about my wizard is that this only happened when i tried to update the phone with the CID unlock program that you have to pay for!
lol it was perfectly fine until i tried to do it! oh well, back to my crappy p168!
May be that CID Unlock program was not meant to be for a G3 and you were updating a G3 so it mixed you IPL/SPL and caused a kinda BRICK. So please be careful before doing flashing things because if you dont be carefull then your PPC may become a heavy paper weight, and a costy one too. LOL. TC
kitty4uhig said:
Farming for eq2 plat isn't easy, but you can buy eq2 plat, guides, accounts & items on sale. We have revolutionized the exchange of money to eq2 plat. Purchase eq2 plat& power up your character ot the next level. Our world class customer service will make sure you are more than satisfied with every purchase. Feel free to contact our 24 hour live support with any questions you may have. Shop now and play as a VIP!
Click to expand...
Click to collapse
Stop this nonsense immediately,otherwise it'll be reported and you'll be banned.Its spam !!!
try this: http://forum.xda-developers.com/showthread.php?t=276963
Cingular 8125 problems
Ok guys i am really pissed i have been looking for three days and cant find it, first off my IPL is at 1.01 and the SPL is at 2.25 and i cant fix it i wanted to install the original 2.25 again and start from scratch but can not find the damn thing so if anyone has it can u just upload it fo me and give me a link that i can get it at please i am sick and tired of waitnin i really like this phone and i dont want to risk bricking it thanks.
Ok, grimgod, aggression is reaaaallly ugly and no freakin one will help with that sh!t attitude (pardon the language, mods). The senior members do everything they can to help the noobs. Have you tried reading the flashing guide, wiki, or tutorial? I'd bet even money you haven't. Have you CID unlocked? Did you flash the button rom twice ( as the guide suggested to get ipl/spl both 2.xx)? Did you flash the official tmo rom (found im the flashing guide)? Have you done anything other than sit on your hands and wait for it to be handed to you? READ AND SEARCH!!!!!!!!!!!!!!!!
http://forum.xda-developers.com/showthread.php?t=310831 <HERE!!!!!!!!!! Should I flash your device, too?
Similar issue... need some Wizard Expertise
I picked up a coworkers old Cingular 8125 that he'd had in a drawer for about a year. Battery was right dead so the phone wouldn't boot. I charged the battery on an external charger for a few minutes, put it back into the phone, and plugged it in to the charger until the LED went green indicating a full charge.
When I power up I see the T-Mobile splash screen (light gray background, some square dots, and the "T-Mobile" logo). And there it stays indefinitely.
Tried a hard reset (Comm Mgr + Voice Cmd + Soft Reset), and it said "Press Send to restore factory default". Pressed the green dialer key (I assume that's send), and it says Format FAT partition, FAT partition complete, and then returns to the same T-Mobile splash screen and hangs there.
So then I tried putting it into Boot Loader manually (Power On + Camera). No problem, shows IPL 2.26 and SPL 2.26. Plug it into the computer USB port (running XP Pro), and then the USB connection shows on the phone. Attempted to flash the Wizard Love ROM to get this thing back to square-one. Error 260. Attempted to flash the T-Mobile stock ROM. Error 260.
Between each flash attempt, I'm pulling the battery out and starting fresh. I think I've followed all the steps I'm finding in multiple threads. But for some reason I'm not able to get this thing to communicate via USB. All RUU's give an Error 260. Am I missing something?
Forgot to mention I'm following the steps outlined in this thread from Dr P. To the letter!
Also did a little reading up on using the MTTY method in this thread by Drug_Store. Thought maybe the existing ROM might be intact, and I might be able get it to a 256MB MiniSD, then write the backup ROM from SD in boot loader. Well, for some reason I don't even see the USB connection option when I use the MTTY - can't ever get to a point where I can issue commands. Again, I think I'm following the instruction. But still no juice.
Nudge, nudge. I'd donate for a solution that works... otherwise I have to keep letting my 10 year old play The Quest on my phone.
I have a wizard (wiza110) running wm5 and i wanted to upgrade it. It was the first time i was trying such thing. I was following these instructions http://wiki.xda-developers.com/index.php?pagename=Wizard%20Windows%20Mobile%206%20for%20newbies. My device is g3. My first attempt was with Button Rom, everything was fine until 99%... i think it was error 302 or something. I took off the battery and plugged it again several times but nothing came out. I had the three-colour screen.
Then I tried The Xda_MiniS_LaunchROM_v154102.exe, still nothing, lokiwiz also...
Last attempt was with wizard Love. USB appears but the ruu can't see the device and stops the process
Any ideas?
i think the device was sim-unlocked...
Flash back to the original rom, charge the battery to 100%. Make a guest connection to windows and start reading this thread from the beginning
do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25
aposperitis said:
do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25
Click to expand...
Click to collapse
Based on my experience and what I've read here, I'm guessing that your original rom had ipl and spl both 2.25. When you installed the button rom, it updated the ipl but nothing else. Just a guess, but that's what happened to me the first time on my G3. I just re-flashed button rom and continued from there. You should try to find the original rom for whatever kind of phone you have (I mean, the rom from the service provider like Orange, AT&T, etc). Their latest rom might not be 2.25. For example, my phone originally came from T-Mobile. I have the T-Mobile rom that is I think 2.26. I keep it handy, but have only reflashed back to that rom once when my extended rom got messed up.
Read the link suggested above. Good stuff. It is possible to flash a phone that is stuck on the tri-color screen, but it might not work the first try.
Same thing here, just youre getting further
I have ipl and spl on 2.26 received it this way. It's G3. I've been a week looking through the forums. Trying to avoid posting here. But damn it. I can't seem to get anything right. I previously had the G1 and Juno, Flashing was a breeze. But here i feel lost.
Basically my problem is i can't get it to downgrade. upgrade. CID unlock, With neither Lokiwiz or WST. A pain. And really NO RUU runs past the 0% it reboots my phone to boot loader image and USB shows but it reads that it can't find my phone anymore. It's been charged to 100%. Deleted TEMP folder. Was guest under activesync. Changed my USB cables 10 times. It's frustrating. Please. Any suggestions??