Downgrading from Mr. Clean - 8125, K-JAM, P4300, MDA Vario Software Upgrading

HELP! I installed the Mr Clean rom and want to go back to the original ship rom, but when I run the original ship rom it goes through and I get an error just before the upgrade.
Error 296 Upgrade Only
This NBF file cannot be used to upgrade your phone, please get a newer NBF File.
Any thoughts on what to do?
THANKS!

Downgrade to button's 1.05 at ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe then you can "upgrade" back to the original shipped ROM.
Good luck!

Thank you, I will give that a shot

Hm, just run your Wiz in bootloader mode and downgrade!

505, I don't think that that will work....

drj said:
Thank you, I will give that a shot
Click to expand...
Click to collapse
I had the same problem, except I was trying to downgrade to do an unlock. But now that I try to install the custom rom, it hangs at 98% for a REALLY long time... around 10-15 minutes. And then it'll go to 99%, but the phone will continue to say 98%. And then, several minutes later, the program crashes on the PC! Any idea what's going on here??

turbo jjjang said:
drj said:
Thank you, I will give that a shot
Click to expand...
Click to collapse
I had the same problem, except I was trying to downgrade to do an unlock. But now that I try to install the custom rom, it hangs at 98% for a REALLY long time... around 10-15 minutes. And then it'll go to 99%, but the phone will continue to say 98%. And then, several minutes later, the program crashes on the PC! Any idea what's going on here??
Click to expand...
Click to collapse
I'd try another PC. Could be spyware, maybe a wee virus.

Related

URGENT!! Wizard WM6 upgrade stuck at 96%

Anyone please help!..
i tried to upgrade my G3 Wizard to Crossbow Underground and it stuck at 96%!..
What should i do? please help.
Yes -- the install will "hang" at 96% for 2 - 3 minutes. But then, it will complete the process pretty quickly.
My advice for ANYONE flashing ANY ROM is to leave the room for about 15 minutes while it's upgrading. Those 10 minutes can seem like an eternity -- especially the 2 - 3 minutes where the install process appears to "hang". DO NOT disconnect the device during the update.
so? this is normal huh? even thought im not CID Unlocked? becouse i didnt check whether my wizard is unlock or lock..
im still stuck 96% for 30mins.. what took this so long?
Ok its done..
but men!.. its still WM5.. now i know that my wizard is CID locked..
Thanks!
double_ofour said:
Ok its done..
but men!.. its still WM5.. now i know that my wizard is CID locked..
Thanks!
Click to expand...
Click to collapse
I have the same problem i only don't know how i get my normal version back
jordy08 said:
I have the same problem i only don't know how i get my normal version back
Click to expand...
Click to collapse
I'd say you have a LOT of reading to do to answer that question. . .
Start with the Wiki and the Stickys at the top of this forum. . . both are chock full of useful information -- yours for the taking

upgrade didn't work

i tried several times like described here http://forum.xda-developers.com/showthread.php?t=285435
but always when i want to downgrade my rom with the mentioned button 1.05 rom it went till 98% an then my wizard didnt do anything until i reboot it.
with the standard o2 rom i have the lokiwiz didnt work. but what could be the fault ? what can i try to get it work ?
peran281 said:
i tried several times like described here http://forum.xda-developers.com/showthread.php?t=285435
but always when i want to downgrade my rom with the mentioned button 1.05 rom it went till 98% an then my wizard didnt do anything until i reboot it.
with the standard o2 rom i have the lokiwiz didnt work. but what could be the fault ? what can i try to get it work ?
Click to expand...
Click to collapse
Who knows, you didn't tell anything useful about your phone or what ROMs or anything else. Try the link in my sig. Read it, do ALL the steps, if you think you can skip something--don't, if "it doesn't work"--then you didn't follow all the steps.
Best of luck,
--M
peran281 said:
it went till 98% an then my wizard didnt do anything until i reboot it.
Click to expand...
Click to collapse
I think this may be part of the problem... How long did you wait? All roms stall at some point and can stall for like 5 mins (sometimes more). Don't do ANYTHING, unless your PC gets an error. Its still working. If it sits for more than 10 mins then you probably do have a problem, but it can sit for what seems like forever sometimes. Just be patient.
If it sits for more than 10 mins then you probably do have a problem
Click to expand...
Click to collapse
i tried it several times and i always had to wait about 20 - 30 minutes and always the same result being hung up at 98%.
about your phone or what ROMs
Click to expand...
Click to collapse
here i have some data. i have
ipl/spl: 2.21(o2 ger rom)
gsm : 02.19.11 (o2 ger rom)
os:2.21.4.3 (o2 ger rom)
i hope that is all the important info u need.
i'll try the link from demontefixo and let u know if it work.
Tried flashing on anther pc yet? For most people with this kind of problem that's the solution.
Tried flashing on anther pc yet?
Click to expand...
Click to collapse
i have 2 pcs and 1 laptop and i used all of them one time.
i used now this installationhttp://forum.xda-developers.com/showthread.php?t=298613
and it stucked on step G3.4 when i want to flash the wizard_love rom with this error:
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
what did i do wrong? i followed step by step like demontefixo said for 3 times.
peran281 said:
i used now this installationhttp://forum.xda-developers.com/showthread.php?t=298613
and it stucked on step G3.4 when i want to flash the wizard_love rom with this error:
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
what did i do wrong? i followed step by step like demontefixo said for 3 times.
Click to expand...
Click to collapse
This is an error that you can get on G4 devices. What are you doing in step G3.4? Read G4.6!
but in the tutorial http://forum.xda-developers.com/showthread.php?t=298613
is described how to determine the wizard type and my ipl/spl is 2.21 and thats G3 device.
peran281 said:
i used now this installationhttp://forum.xda-developers.com/showthread.php?t=298613
and it stucked on step G3.4 when i want to flash the wizard_love rom with this error:
ERROR [300] : INVALID UPDATE TOOL
This error message will appear when you use the incorrect RUU version to upgrade.
what did i do wrong? i followed step by step like demontefixo said for 3 times.
Click to expand...
Click to collapse
That error indicates you aren't CID Unlocked. Is your phone booting now? or are you at the bootloader (rainbow) screen? If you are at the bootloader, then flash your official rom to get a working device. Once you have a working device, then go to step G3.6 and do the CID Unlock procedure.
ALso remove your SD card while you are doing all of this until you get it CID Unlocked and onto the TMobile 2.26 official rom (G3.8).
AND yes, you have a G3, so you don't (and shouldn't) be in the G4.x steps.
i want to downgrade my rom with the mentioned button 1.05 rom it went till 98% an then my wizard didnt do anything
Click to expand...
Click to collapse
yes but thats my problem. i tried it like described here http://forum.xda-developers.com/showthread.php?t=285435
and always the same problem. is there another way to cid unlock the device ?
peran281 said:
yes but thats my problem. i tried it like described here http://forum.xda-developers.com/showthread.php?t=285435
and always the same problem. is there another way to cid unlock the device ?
Click to expand...
Click to collapse
This is my last post for the day as I can't handle anymore of this (its not just you peran, but the other half dozen posts I've read in the last hour or so where people just aren't following the instructions they are given. These methods are tried and true, and they work. And yes, this is the way to CID Unlock your phone unless you pay to have it done)... In a previous post to you, it was stated you had to get back to an official rom first. Have you done this (your replies indicate you just continue to do other roms)? You need to get the latest rom from your carrier and get your device working again. Get it all charged up, pull out your SD card, then try flashing back to the button rom (I would also suggest you try pulling the button rom down again in case there is something wrong with your previous download of it).
Its the weekend, I'm going to go enjoy the spring weather
i did it like u suggested mfrazzz. i know that my phone isnt CID unlocked. but that is my problem. i read the mentioned article x-times and did it like described but the problem is : when i downgrade to button 1.05 rom then my pda stuck at 98% and i get the message from the update program on my pc that the downgrade was successful. but it isn't. why? till this step u cant do much wrong i think... :-(
Have you flashed back to the official rom from your carrier? Until you do that and get your device back working there is no point in trying to continue to flash the button rom (or any other rom). You have to get back to your carrier's official rom first. None of your posts indicate you have done that.
with the standard o2 rom
Click to expand...
Click to collapse
i always went back to the official rom from my provider and this always works perfectly. i tried it today again but always the same stucking at 98%.
i did it STEP BY STEP but it didnt work.
is there another rom i can use than button 1.05 ?
Is there no other rom then the one from button to downgrade my ipl/spl to 1.xx ?
please help.
I'm not aware of another one.
You might want to try this thread (I know its not the same issue, but might be worth trying to see if it makes a difference)
http://forum.xda-developers.com/showthread.php?t=294107
You might want to try this thread (I know its not the same issue, but might be worth trying to see if it makes a difference)
http://forum.xda-developers.com/showthread.php?t=294107
Click to expand...
Click to collapse
I tried it but it didnt help.
now i used Xelecin's 1.08 rom and this one worked. then i used lokiwiz and it was successful. but then i flashed the tmobile 2.26 rom and this worked but i couldnt use my sim-card any more. always when i insert my pin it said unknown sim and then crashes. i thought i sim-unlocked the wizard? another problem was when i want to flash the official o2 rom it said unknown vendor id...but i used before lokiwiz and there were no errors...and the last question, i know there are many now, where do i insert the sim-code i got from lokiwiz?
i hope someone have some answers...thx before

Phone locked in bootleader!! Cannot even Hard Reset!!

Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...

[Walkthrough] How to fix your bricked phone

So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse
papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...
Too bad it'll be stated a million more times afterwards too.
falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol
ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!
ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?
ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider
Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.
The instructions to do this are actually in my newbie thread. Which is a sticky.
TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...
help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......
Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.
And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec
If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.
Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.

what am i doing wrong

ok, i am totally confused. i had flashed to three different roms since joining this forum. i tried to flash ttrans OTv5.0UL and nothing happens. bootloader comes up, screen goes white, generic pda menu opens and all seems fine. when phone starts back up, all of my original setting are there just like if i only did a soft reset. i tried again with a different rom and the same thing happens. i have tried 4 times and nothing. can someone please let me know what i am doing wrong
when did you buy your wing???
and are you using flashcenter ?? so it can temporary cid unlock the device?
i got my wing in feb or march 08. yes i do have flash center, and i have used it w/o problems before. i have flashed from touch it to open touch and one of aserg's roms too. i have been using OT 4 lite black for weeks now. i have been watching the threads about the new OT 5. so i downloaded it and nothing new is flashing.
does this help any?
digitalknoll said:
ok, i am totally confused. i had flashed to three different roms since joining this forum. i tried to flash ttrans OTv5.0UL and nothing happens. bootloader comes up, screen goes white, generic pda menu opens and all seems fine. when phone starts back up, all of my original setting are there just like if i only did a soft reset. i tried again with a different rom and the same thing happens. i have tried 4 times and nothing. can someone please let me know what i am doing wrong
Click to expand...
Click to collapse
Please provide more details as to how your trying to flash your device.
Are you using the standard activesync method or via SD?
Regards,
ttran i'm honored!
ttran001 said:
Please provide more details as to how your trying to flash your device.
Are you using the standard activesync method or via SD?
Regards,
Click to expand...
Click to collapse
iwas hoping not to bother any of the main guys with this little problem, but i'm glas your here (love your OT's btw ). ok, i am using the standard activesync method.
heres what i do:
1. download new rom and put it inside my RUU folder on my computer's C drive.
2. run the herald-uspl.exe.
3. follow the prompts
thats all i do and it used to work. i don't know if this helps, but it's the only other thing i have been doing diff. on another thread i asked if it was ok to delete old roms out of my RUU folder. i actually removed my OT v4 lite black and then put the OT v5 UL and ran the uspl. do you think thats what it is? maybe you have to have your old version in the RUU before you flash to a new version?
hope this helps
No. You don't have to have anything but your newest ROM in the RUU folder. When flashing, the phone doesn't know or care what you currently have flashed, unless that ROM is causing problems with your active sync. If that's the case, place your phone into bootloader mode, install the stock ROM (unless you have a HardSPL phone, and it sounds like you don't since you're using USPL.) Then boot up the ROM and run the USPL.
ok, so now know what to do, but why did this happen? whats wrong with the herald-uspl?
i just checked my device info and it says im running open touch v3! i thought that i was using v4. i have hard-spl downloaded, but i dont know if i need to use it or not. should it? then try to flash?
Unlock your phone with hars spl then run the exe from ruu folder. This method worked for me. I did not try the other way since my phone is unlocked but it should work aswell.
shep211 said:
Unlock your phone with hars spl then run the exe from ruu folder. This method worked for me. I did not try the other way since my phone is unlocked but it should work aswell.
Click to expand...
Click to collapse
OK, i'll give it a try
Link to unlock phone software and howto
http://forum.xda-developers.com/showthread.php?t=358225
digitalknoll said:
ok, i am totally confused. i had flashed to three different roms since joining this forum. i tried to flash ttrans OTv5.0UL and nothing happens. bootloader comes up, screen goes white, generic pda menu opens and all seems fine. when phone starts back up, all of my original setting are there just like if i only did a soft reset. i tried again with a different rom and the same thing happens. i have tried 4 times and nothing. can someone please let me know what i am doing wrong
Click to expand...
Click to collapse
I'm sure you already did this, but I'll throw it out there. Did you leave the original .nbh file in the ruu folder? I don't think you can have more than one .nbh file in that directory.
dougstoner said:
I'm sure you already did this, but I'll throw it out there. Did you leave the original .nbh file in the ruu folder? I don't think you can have more than one .nbh file in that directory.
Click to expand...
Click to collapse
actually, here is exactly whats in the RUU.
i hope it helps
Ina Weetald
ok, stoner, you got me.
that was the ticket. i was trying to flash about 4 things at once and i guess my wing flew over to the easiest nbh. i deleated all of them except the BAD ASS OT v5 UL. holy monkey!!! what a peach. i have to thank all of you for the help. i guess we all have these moments at some point in life. well i'm going to start playing around with the new rom. thanks again
digitalknoll said:
ok, stoner, you got me.
that was the ticket. i was trying to flash about 4 things at once and i guess my wing flew over to the easiest nbh. i deleated all of them except the BAD ASS OT v5 UL. holy monkey!!! what a peach. i have to thank all of you for the help. i guess we all have these moments at some point in life. well i'm going to start playing around with the new rom. thanks again
Click to expand...
Click to collapse
Ha, wow that was a stab in the dark! Glad that helped man. So how do you like 5.0? I'm thinking about flashing to it...but heard so many issues with it though.
it looks really sweet!!!!
dougstoner said:
Ha, wow that was a stab in the dark! Glad that helped man. So how do you like 5.0? I'm thinking about flashing to it...but heard so many issues with it though.
Click to expand...
Click to collapse
OT-5UL looks great all around. this is my first time with ultimatelaunch, so thats cool too. i haven't been able to go thru the posts for some of the fix issues. the only thing i'm a bit bummed about is the amount of memory left after the flash (program-20) i'll keep playing with it. hey thanks again for the fix
digitalknoll said:
OT-5UL looks great all around. this is my first time with ultimatelaunch, so thats cool too. i haven't been able to go thru the posts for some of the fix issues. the only thing i'm a bit bummed about is the amount of memory left after the flash (program-20) i'll keep playing with it. hey thanks again for the fix
Click to expand...
Click to collapse
Yeah man, no problem. I finally decided to hard spl, and tried out 5.0 and 4.0 and I think I like 3.0 the best. 5.0 seemed kinda buggy.
dougstoner said:
Yeah man, no problem. I finally decided to hard spl, and tried out 5.0 and 4.0 and I think I like 3.0 the best. 5.0 seemed kinda buggy.
Click to expand...
Click to collapse
i'm too scared to hardspl. i have the download, but not the nuts to try it. whats the hype about it anyway? it seems like some sort of badge for people in here. not you, but you know what i mean?
i'm gonna let the pro's go as far as they can with the OT V5 UL version and then probably go back to v4. gonna miss the UL (damn).
digitalknoll said:
i'm too scared to hardspl. i have the download, but not the nuts to try it. whats the hype about it anyway? it seems like some sort of badge for people in here. not you, but you know what i mean?
i'm gonna let the pro's go as far as they can with the OT V5 UL version and then probably go back to v4. gonna miss the UL (damn).
Click to expand...
Click to collapse
The HardSPL makes it so that if you flash a bad flash, you don't have to flash into the Stock RUU again just to get a working activesync connection to be able to flash again.
Courtesy of Ivanmmj
Step 1. Download Herald-USPL-Beta3. http://www.megaupload.com/?d=A4N36HLO
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
* Your screen on your cell phone will go white around the 75% part of the "second step" now.
* ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
digitalknoll said:
i'm too scared to hardspl. i have the download, but not the nuts to try it. whats the hype about it anyway? it seems like some sort of badge for people in here. not you, but you know what i mean?
i'm gonna let the pro's go as far as they can with the OT V5 UL version and then probably go back to v4. gonna miss the UL (damn).
Click to expand...
Click to collapse
Hey, I was scared for a LONG time to do it...I read so much info before I finally decided to do it! It took me like 2 weeks of reading before I decided. It's an EXTREMELY simple process. Plus, it makes flashing easier. I was getting weird errors trying the USPL method sometimes. Anyway, just do this.
FIRST, make sure your IPL number is atleast 4.000 or higher. You can check this by holding the camera button down, and then doing a soft reset. HOld the camera button down till you enter the bootloader menu. (It's like 3 gradient colors).
If it's higher, great, you are ready to proceed.
Next, download this file.
http://rapidshare.de/files/38148213/...l_WM6.rar.html
Unzip it, and it will contain 3 .cab files you need to install in a certain order.
1. Install canonyang.cab
2. Next, aserpolicy.cab
3. disablesecurity.cab.
Do a soft reset.
Put phone in flight mode!!!!
Now, go to the folder you just unzipped that file from. I think the default folder will be called hard-splwm6 or something like that. Go and run the RUU.exe file in it. Just follow the instructions. The screen of your phone will go white, but just wait, wait, and it will reboot itself.
Presto, you are hard spl, and can load whatever rom you wish!

Categories

Resources