Related
I have no back up image.
What should i do?
_Nomad_ said:
ok... You don't need activesync to do a ROM upgrade/downgrade...
Push the two buttons on the right side while pushing the reset button. That should bring you to the bootloader screen. Make sure that your SD-card slot is empty, and plug in the USB-cord. Now the word USB should appear in the lower right corner. NOW, start the RUU and install the 1.X rom.
Click to expand...
Click to collapse
He helped me out, so now he can also help you out...
Also check the stickies... Lots of helpful info in those..
The thing is how i get into this state.
Upgrade proccess stop at 94 percents and hang up.
As I can undestand that now i need only image of my original rom to restore?
Big thanks, i did not know why, but with ROM version 1.xx it works.
I have tried thousands time with different ROM version 2.xx and they all throught ERROR 260.
[email protected] said:
Big thanks, i did not know why, but with ROM version 1.xx it works.
I have tried thousands time with different ROM version 2.xx and they all throught ERROR 260.
Click to expand...
Click to collapse
Did you CID unlock?
Yes, i have already Unlocked CID, before starting flash ROM.
HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
ditto
ensophalic said:
HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
Click to expand...
Click to collapse
That was the same rom that toasted my Qtek 9100 and now I'm stuck at the 99% mark before I get update:[302] error. Sorry didn't mean to steal your thread m8 but when I aksed the forum if they could help me out I got zero response ...so mines a brick right now.
BTW: I've tried the Wizard Love ROM but that was spanish I think and comes up with "INVALIDO" or something similar. I've fully charged the battery, removed the SD card and disabled "allow USB connections" in activesync, along with killing off wcescomm.exe ...but still no joy. Hope you get sorted with yours soon.
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
xeno1 said:
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
Click to expand...
Click to collapse
Got mine fixed by using the Xda_MiniS_LaunchROM_v154102.exe from the link in the definitive guide sticky. So as they say RTFM!!
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
kevinalmere said:
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
Click to expand...
Click to collapse
Always post the data of your your phone,to get help.
secondly you had a bad flash,perhaps your phone is CID locked. Which rom were you trying to flash ?
Now to recover,download the official carrier's rom and flash it while in bootloaders.The phone will start working again in default status,then,Read and understand the unlocking method and the flashing guide,read the stickies carefully and perform the method correctly.
cheers !
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Help!!!
I have same Problem with TNE-V1.0n_4mb.exe
IPL 3.08
SPL 3.08
kevinalmere said:
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Click to expand...
Click to collapse
If you can go to boot loader, most likely you will be ok. When you plug in the usb port, does the words in the screen change from serial to USB? Once it changes, then flash your official, and then CID unlock your device (this is different from SIM unlock). Then flash to the ROM you want!!
PS: Go read wiki about how to unlock and flash and understand more about your device. http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
kevinalmere said:
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
Click to expand...
Click to collapse
Vista dont like upgrading and stuff...but there is a work around, search the forum and see if you find it. Or try using XP.
okee problem solved working again
thanks for your help!!!
kevinalmere...
How did you resolve the issue I'm having very simular problems and believe it's my Vista OS causing the problem..
Orange SPV M600 G4
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 4.0.0.0
Sorry should explain my issue incase anyone can help.
I attempted an upgrade to WM6 using an Upgrade .Bat from this site. I was slightly impatiant due to not being able to complete the downgrade first anyway the upgrade frose, after a while I canceled the update and carried out a hard re-set... Since then I'm not able to boot nor connect to my desktop via Active sync (WMDC (Vista))
I've followed every instruction I can find but only to be meet with RUU Errors saying can't connect or file open. I can however acces my Bootloader screen and when connection is made the USB symbol shows on the screen of my phone...
Any help would be greatly recieved......
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
If i were you I'd use this one =)
futureshock said:
ok i found it i didn't read further the 1st page on sspl thread
edit:
have repacked it with runme.bat and 77.7er SSPL ...
Radinly_1.54.30.10
Click to expand...
Click to collapse
At least I did and it worked =)
and then I'll highly recommend this WIM6.1 release by FutureShock: http://forum.xda-developers.com/showthread.php?p=2094056#post2094056
GL =)
I've GOT IT!!! using various mix and match method, im flashing the phone now!!! fingers crossed it'll boot later
UPDATE: DOESNT WORK! PLEASE HELP
It sure will.. Even I got it to work really fine
crap!. doesnt work. it's still SPL 1.09 and stuck at 2nd boot screen.
is there a ROM editor that works for meteor? can someone please suggest one that can be used to sign the nbh file.
jerpelea, or futureshock, please help
not good news
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
PiGeonCZ said:
I think I know what do you mean. My device was in very same state like yours few mnonths ago.
Try to run mtty and the command "info 2" without quotes.
Do not forget to disable USB on activesync settings before running mtty.
You will get an answer which includes the CID of your device.
If not (this was my case), you have to send it to the repair center probably.
My device CID was Qtek_A07 (RUS) and I have tried to instal the first official WWE 1.34 ROM update (combined from SPL.nbh and ROM.nbh) and it replaced only the SPL, and the ROM update crashed.
There was not way out so I sent it to the repair center.
The WWE images are expecting the device with CID Qtek_Z12.
Click to expand...
Click to collapse
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
alexnvidia said:
this is what i get with mtty
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
what's the meaning of this? is there any hope?
i ran the format command anyway. device reboots and still stuck at the windows mobile logo screen. what should i do next?
Click to expand...
Click to collapse
why did you format ?
try to reflash 1.09 spl
and after this wwe one of 1.34 roms to get 1.10 spl
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Click to expand...
Click to collapse
jerpelea: First of all I will say thank you for taking all that time you do spend on the ROM cooking/building/making/what-ever-is-the-right-name and I/we really appreciate it!
jerpelea said:
but i dont know if you have the knowledge
Click to expand...
Click to collapse
I think that comment was really unnecessary!
As a n00b I know how hard it is to understand what’s happening. I did read the wiki’s and still I didn’t get HOW TO upgrade a ROM until I found a great post in FutureShock’s thread
darkDirk said:
First of all:
It's fantastic what you are doing with wm6.1 and the Breeze, Futureshock !
I am new and trying to upgrade it myself, but at first I didn't have any luck.
Here is a simple newby step-by-step manual:
- Download and extract a MTeoR-FutureShock-WM61-xxxx.x.rar
- Check your Mteor battery in more then 50 % full
- connect the Mteor to the computer via usb and check if Activesync works
- go with DOS (cmd line) to the directory and start runme.bat
- On the Mteor press camera and powerbutton at the same time.
- then immediately press any key on the computer to continue the batch script.
- now you should see the 3-color bootscreen
- press any key to start the rom-update program and follow its directions.
When the update is finished (in less then 5 minutes), then wait untill the first boot is complete.
If you don't get the 3-color bootscreen or you the update on the Mteor stays on 0 % and the rom-updater displays an error, try testing this:
On the Mteor start the explorer and in the root directory (press UP once) find SSPL.EXE en start it.
If the Mteor won't start the program and there is an error like "insufficient trustlevel".
You need to remove the application lock on your Mteor.
Run SDA_ApplicationUnlock.exe on your PC with Activesync working and then install SP_AllowCertificateInstall.cab on the Mteor.
You will find those two in the .rar in ".\opt Software\Unlock Tools"
Then redo from the start.
Then, Have fun !! (Futureshock & DarkDirk)
P.S. works on a BREE100 with IPL-0.90 and SPL-2.05.
Click to expand...
Click to collapse
But I still do not know what SSPL, SPL, IPL or whatever there is does to me or/and the phone.
Anyway. Thanks for all the work.
if someone has a corrupt CID just send me an pm...
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
with all the respect what you do for this community, isn't taht you who advice us to update the SPL before trying your images?
in this thread http://forum.xda-developers.com/showthread.php?t=384398 you should probably higlight that the update should be done only on WWE devices.
jerpelea said:
If you bothered to read the Wiki, you would have seen this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
If you can't bother to read the wiki, don't play with roms!
Actually, I did read that, and a couple of problems:
1) Boot Loader is 1.09
2) OS won't load, so can't use any of the ActiveSync-based methods for downgrading to an older version, such as 1.04.
3) CID appears to be corrupted, as per the earlier output pasted.
from other forum ...... so read wiki
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
but i dont know if you have the knowledge
Click to expand...
Click to collapse
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
alexnvidia said:
hi guys,
i was excited about the new Radio upgrade, so i tried to flash it. i got an error, because my SPL is 2.05. so i tried to unlock the phone using jerpelea's guide, flash to 1.09 -->success, then WWE (1.10) but an error occured saying invalid vendor ID during WWE flash. now i have SPL 1.09 on my phone and my phone is stuck on the 2nd boot screen of jerpelea's WM6.1 beta 4 ROM. my phone is fully unlocked using jerpelea's unlock guide, that's how i got to install SPL 1.09 successfully. how can i recover my phone? please help.
Update 1: i tried to flash back the original dopod 595 WM5 ROM. i mixed the RUU updater from the latest official ROM with the nbh from dopod WM5 ROM. the flashing works. when it's 100%, the phone reboots and, i got back to the same problem. stuck at 2nd/3rd boot screen. i now have IPL-0.90 and SPL 1.09 on my phone. Please help me to recover my phone. i've tried to hard SPL shown in the wiki guide, doesnt work. says invalid vendor ID crap. i really dont know what to do now.
Update 2: when the device boots, it stucks on the 2nd/3rd boot screen and if the USB cable is attached, for a brief moment, windows can detect the phone and i can even browse the content of the phone from my PC. but after that, the device disconnects itself and just remain stuck at the 2nd/3rd boot screen. the device appears to be totally freezed/hang. even the LED charging indicator will not turn off when i unplug the device from computer
i believe what i need to do now is to make a nbh image that is signed to i dont get any corrupted image message when trying to flash. i used HTC ROM editor to mix and match the SPL and IPL file so that i can downgrade the SPL to 2.05 and upgrade it again later. but i dont know how to sign nbh files.
Click to expand...
Click to collapse
run terratem
type info2
if it sais A07 then just flash rusian 1.34 rom and enerithing will be fine
application unlock it
run sspl 77.7
flash wm6.1
if it says enithing else you need to locate your original rom
till now i found that it sais a07 in most cases
BR
alexnvidia said:
i did try to read as much as i could but apparently i didnt come across that. when i flashed to SPL 1.09, the device booted up just fine. it is when i try to update to WWE 1.10, the update process failed and bricked my phone. for your information, i was following the exact steps described by you in your unlocking/SSPL guide. you mentioned upgrade to SPL 1.09, then WWE 1.10. this is exactly what i did. i dont know what went wrong. im sure if im as knowlegable as you are, i wouldnt have screwed up my phone. my bad.
just to be fair, your method did work when i updated my dopod 595 (WWE device) to your WM6.1 beta 4 ROM. but i never upgraded my SPL to 1.10. i only thought of upgrading SPL when you posted the new radio release and that's where i screwed up.
anyway, what is important here is, is my phone unrecoverable? im reading the links you posted as i type, and i'll give the methods. maybe based on your experience, you could suggest some ways to do it. thanks.
Click to expand...
Click to collapse
it depends on the info displayed on terraterm
for A07 you can use the russian rom to recover
this is what i got from terraterm. same as mtty.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
i did flashed back to my original ROM after the first stuck in WM screen incident. and amazingly the flashing process works after several mix and match. after the original (WM5) ROM completed flashing, my IPL is downgraded back to 0.9 and SPL is still 1.09, and im still stuck at the WM logo screen (this time WM5 logo).
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
futureshock said:
terraterm is a tool like mtty
what is your orignal rom??
just try to flash over sdcard... (look in wiki4more infos about that)
Click to expand...
Click to collapse
i tried SD card flashing too yesterday. it says not allowed. i have already flashed over the original dopod 595 ROM and my phone is now WM5. the flashing is 100% successful, but it is still stuck at the second boot WM screen.
i think im in a really screw up position now. i have SPL 1.09 and IPL 0.9. i dont know what is corrupted now. is it the CID? SPL?
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
futureshock said:
cid you can check with mtty and info 2...
if that so... just do what i have wroted in pm...
you could also just try the old htc rom (w. SPL 2.05)
Click to expand...
Click to collapse
both mtty and terraterm give me the same msg when i type info 2. it says time out (refer above for exact error message).
the original dopod 595 rom has SPL2.05. and it was successfully flashed into the phone. when the phone reboots, it is still stuck at 2nd boot screen (WM logo). i checked, the SPL is still 1.09, but IPL has been downgraded to 0.9.