Database Develop

Problem Updating the XDAIIs New Rom

Dear All
I would like to have some urgent help on this one. I have downloaded the new Rom Update for my XDAIIs. I have successfully started the ROM update. I reached the screen when it prompted me with the device information and I clicked on UPDATE to start the process. My XDA screen went to Black with the USB indication ...and v2.06 indicated below. Nothing happened and the wizard did not proceed with any further indication except "Checking the information in your device ..." etc...It froze on this and I had to restart my PC. Now my XDAIIs is remaining on the same blacked out screen and won't boot to its previous room if I do a soft or hard reset. Have I "Killed" my XDAIIs? Is there anything I did wrong? Pls HELP !!!!!!!!!!!!!!!!!!
Thanks
Ashraf

No Problem..
1. Do a soft reset (the screen will just blik once and still remain blank)
2. Put the device in cradle/USB
3. ReDo your upgrading procedure by double clicking the upgrade file
It should work then... good luck

same
Guys,
I have the same problem only a little more stupidity on my part, check it out at - http://forum.xda-developers.com/viewtopic.php?p=130797#130797
As you can see kumar00455 your advice doesn't work in my situation
any other help ??
Heath

Kumar
Thanks pal !
I've been able to sort out the problem. I actually needed to stop the Active Sync application on my PC so that the upgrade wizard could connect to the XDAIIs via USB and perform the update. It will not work if the Active Sync task is still running as a process.
After running the app again, the upgrade worked seamlessly without any glitch...!!!
Thanks for your support.
Ashraf

continually rebooting -- help

Hey guys,
I have a ATT tilt and installed the duut touchflo apps. I then clicke on the HTC music pp in programs and now my phone is continually rebooting. it get to the green screen and re-boots.
HELP

never mind guys -- I was finally able to get the hard reset to work

Hey,
I have the same problem with a french Orange model I just received today... keep rebooting.
hard reset doesn't seem to work and I can't boot even to install hard SPL and flash another rom to try.
Could mtty help me or something ?
Thanks,
Cedric

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!

Put the phone in bootloader mode and flash back to the original ROM.

since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?

You can find in the Wiki the latest official roms of every brand for our Wizards .-

ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?

i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this

With everything i’ve read the only people who’ve had any success had CID unlocked devices.

ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?

I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).

I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?

Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse

Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks

Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse

I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks

i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.

same proplem here with
ipl 2.16
and spl 2.16

I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.

Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman

Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

My tytn II do not want to boot

hello!
I am new here and i got one big problem.
So please help me!
I tried to flash my tytn II with this rom(ENDED- 28/V/2009 Anryl WM⑥.⑤ 21725 FINAL ULTIMATE(101RAM) -ENDED- ), but when i finished the flash, my phone want to boot. It stops on black screen and show "HTC"
If someon know how to fix it, please help me!!
R 1.27.16.21
G 22.52.88.13h
D 3.34.00.00

did you flash jumpspl and hardspl first?

Yes i did.
I did everything like it said in http://forum.xda-developers.com/showthread.php?t=433835 and my phone is stuck in bootloader. So how can i reflash it? i tried to flash it again with sd card but when i use power + camera + stilus to get bootloader, in a second there is a white screen where is written that there is no image, and it go back to three color screen mode, and in the bottom is a white screen where is written "serial"
When i try to flash it with activesync there is an error 262. I spend a lot of time reading many posts here, but i did not find enything what help me.
Any sugestions?
Thanks!

Bro, did you solve it? please let me know. Same issue and as described in the faq's tried using MTTY but that one also does not connect.

Unable to Load Bootloader

I have tried hitting record + power + reset and still no dice.
I did this last Jan to my BA with few problems, put in the wm6.1
Wanting to install this one WM6.5
I also installed the Wizard Service Tool and it doesnt seem to work. It will give me info but the hard reset and other rom features don't want to work.
is there a workaround for gettin to the bootloader? Or should I take this all as a sign not to brik my phone? ;D
thanks,
chela

hi , i'm new on the forum...i think i've the same problem, on my PDA2K..
I try to install a new rom from wm2003se, using a file called "preparazione BA"( i think i've unlocked the extrom), then i normally setup with the MaUpgradeUt_noID.exe..But now, when the upgrading is completed to wm6, i'm not able to load the bootoption..i can see 4 colour bands (green blue red white) but no option to boot. The rec+photo+reset seem not to work.
Could anyone help me\us??
Regards at all
Davide

after 2 hours..here are some news: my pda2k display became with the 4 color but there was writen something about R none, G none and (version onf the rom i tryed to install) then pressing rec+cam i saw for little fraction of second the menu enable kitl ,clean registry, etc.. and then suddenly the wm6 starts. After installing the OS ask me to reset..Well, it return to the same 4 color, and the only word i see is R1.11.00
I'm getting crazy...
Please big chef tony help me!
i don't know what to do now...i'm little down
Davide

...lol maybe because I dont do this often enough, but this case was solved with a little bit of RTFM!
I didnt realize I was pressing the wrong fsking button! derr!
Here is Chef Tony's post...should carve it into my desk!
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners

Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08

i've solved my problem..reading on other forums, they suggest to install a rom WM5, where there was radio upgrade too..After i was able to install WM6.1 ! Now..i have to wait..and crossing my fingers!
Thank you all, if anybody has question ask me, i'll happy to help you
Bye
Davide

Davidenji said:
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
Click to expand...
Click to collapse
Nothing strange about what is in photo #2! That is the debugger screen.
Looks like you got it rolled back to the original ROM but if you decide to put the latest stable ROM 6.5 on there you're going to have to follow the Chef's directions in the above supplied link.
Good luck,
Chela

glad you found it out, you are right, there was something wrong with the radio, which is why in screenshot #1 there is only the radio listed and i think that's also why in #4 the comm icons are red, i've never seen that before, but could also be a custom skin in that rom.
brujeria is right, there is nothing wrong with the 2nd and 3rd screenshot, except for the 2nd one only showing the rom and no radio or protocol, meaning that the device was probably resetted by pulling out the battery and not pushing the reset pin with the stylus, unless that was also a radio issue.
unless you already started customizing your device you should probably think about hard resetting it once again and trying if that works, or even re-flash the rom, without flashing the radio, that way you'd know for sure, if from now on you'll always have to flash a "baked rom" (usually a term for a cooked rom, together with radio and extrom, a full flash, in this case i mean rom and radio rom, since the extrom is not really flashed anymore).
with best regards,
Chef_Tony

i've already customized...a little! Now, everytime i soft reset i read this: R 1.15.00 , G 1337.45 , D 1.21 michy.
I've no problem at moment..but i hope i won't never hard reset!
This Rom (WM6.1 included only Rom upgrade) it's nice, but i'm interested about WM6.5..anyway i think to keep this one untill a problem will come out
P.s. Like you say, now the antenna isn't red anymore..it's bright green
Thank you a lot for the support guys!