miniSD ROM Upgrade w/ bootloader 2.x - 8125, K-JAM, P4300, MDA Vario Software Upgrading

has anyone successfully updated a wizard with 2.x bootloader from a sd card?
i used ntrw.exe on a nk.nbf file to back it up to my minisd while ntrw confirms 512mb written but it seems to be a unformatted card

Related

using ntrw doesnt create a bootable SD ROM image file

When I backed up my Blue Angel ROM info using these commands I was able to create a bootable SD ROM card:
d2s 80000000 02000000“
d2s 60000000 00300000 sd a
d2s 70000000 01080000 sd a
I used the ntrw utility to backup the SD card to my disk:
ntrw read XDAIII.nb1 E:
I then formatted that same SD card as a test and used:
ntrw write XDAIII.nb1 E:
So far so good but now if I bot my BlueAngel using Power+Record+Soft reset there is no prompt to flash from SD.
Any ideas why, is there a trick to using the ntrw utility? I used a 512MB SDIO card, is that too big?
Thanks.
Hi,
Did you solve this problem as I am unable to boot from the SD card.
Thanks
Msuk
No I didn't get a solution for booting an SD created with ntrw .
Sorry.

Bootloader mode and 1GB SD card

All,
I have to return my MDAIII back to T-Mobile so I need to put the original rom back in. Luckily I made a backup using a 256MB SD card and NTRW.exe
I am using ntrw write myrom.nb1 h: to write the ROM to a 1GB SD card but when I put the MDAIII into bootloader mode I do not get a message asking me to upgrade does anyone now why this is?
Do I need to use a 256 MB SD again to flash the phone?
Thanks
Msuk

Backup of ROM

All,
I have a MDAIII and I would like to back up my current ROM.
I have followed the steps outlined here
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=151&PN=1
to extracting the rom using NTRW.exe version 2.
Now when I try to restore the ROM I use ‘ntrw.exe write myrom.nb1 h:’ and put the sd card back into the phone and put it into bootloader mode but the phone does not boot from the SD Card. I have tried a 256mb and 1gb sd card but the phone does not display a confirmation to upgrade - can anyone help?
Thanks
Msuk

Upgrade Alpine rom via SD card

Hi, I would like to upgrade my rom from SD card. I have the official xda rom pack
Xda_IIi_Upgrade_v111171.exe
and i extracted nk.nbf from that archive
I then inserted an SD card into my reader and tried a
ntrw write nk.nbf f: (which is the card reader letter)
It starts to write and then a few seconds later i get
WriteFile(): nk.nbf -- The parameter is incorrect.
anyone tell me where im going wrong ? thank you
Id also like to know the next step bootloader etc as i havent been able to see a guide for that yet.
many thanks
maltloaf

how I upgrad my k-jam by sd card

is there any way to upgrad my K-jam by useing the sd card as some other devices like jas jam by renameing the rom file and save it on the card
I mean to flash with out cable just by the card
my device dos't make any connection with the computer so I use the cable only to charg the battery
No, htc devices doesn't use that method.
SD method in htc is only suitable for unlocked G3 wizard, and the SD image can only be generated from a working unlocked G3 wizard, you can't generate the image from ROM file.
I did that but in other way I could to copy the new rom from other k-jam device to my sd card then i put the card in my device
but now I haven't an other k-jam device I only have the one how has a problem in usb
by the way I unlocked my device and it 3g

Categories

Resources