I searched the forum, and didn't find any solution for this problem.
The problem is I can connect to every network except my own. I can connect with my laptop to my network, my brothers computer connects fine to it, and the router never gave me any problems until now.
The router is a WRT54GX4, i am guessing it has something to do with the latest rom 2.26 not being able to connect to it because of the mimo "feature"
I heard that older qtek roms were able to connect to the router (could someone verify this?)
If they could connect could someone give me a link to an old compatible qtek firmware (i am sorta new to this and not sure which one would work)
Thank you.
What version of the Linksys firmware are you running? A lot of times an upgrade will fix such issues.
I am running the latest version 1.00.17 of the firmware, i tried changing some of the wifi setting on the router but I still can't connect.
I am running the latest version 1.00.17 of the firmware, i tried changing some of the wifi setting on the router but I still can't connect.
it must be something with 2.26 and linksys, i have 2.26 and have no issues with my SMC or 2wire... or any other wireless router... havent tried it on a linksys, everyone that i know refuses to own a linksys so i dont have one handy to try
Hello.
I've got HTC Wizard (Era MDA Vario) (Era is T-Mobile in Poland) with Crossbow Underground ROM. It's a very good phone at all but i still reach problems with WiFi. Even when I'm 30 cm from wifi router (Linksys WRT-300N), when I turn the WiFi on, it can't connect to my network. When i go to "Network Cards" menu and select Connect manually, Wizard connects almost always. Can I set my Wizard to connect automatically to my network when I turn WiFi on? It could connect automatically when I had very old 1.XX original ROM.
My current Radio ROM is Cingular 2.25.11, i've already tried 2.47.11. Anybody has this problem or know how to solve it? Maybe it's just a simple registry change?
Yours sincerely,
kasok
i also have a problem like that
mine connects automatically however, it losts connection after 10 sec. than it doesn't connect anymore. after soft-reset i can connect again
i'm using molski v3.3 radio 2.19
Hi, I've had my Tilt for a while now, and I just updated to the new WM6.1 ROM this morning. However, after the upgrade, I could no longer get the wifi to work. I can connect to the wireless networks (tried different networks both open and secure), but when I try go to a website or use the internet, it just sits there and then says cannot connect. I have tried everything I can think of to fix the problem. I tell it to connect through work and through the internet, and messed with some other setting but that wouldn't do it. I plugged the tilt into activesync and it used the computer's connect just fine. Anyone having or had this issue, or have any suggestions?
Chris
Did you install the remove hidden proxy CAB?
If not, go here and get it:
http://www.4shared.com/dir/6996097/3f1f5d36/cabs.html
It's the removeHiddenProxy4CWS_0522 file
There may be others that do the same thing.
I installed the hidden proxy cab on my tilt, and the wi-fi still isn't working. Any other suggestions on fixing this problem. It's killing me. I though I'd be able to upgrade and reinstall all my files in just over an hour before I ran into this issue.
Update: Okay, I reverted back to the previous WM6 ROM and the wifi worked with absolutely no problem right off the bat. I don't understand what the issue could be and whether anyone else is having the problem. I'm going to try the WM6.1 ROM one more time, and then give up. I have to have wifi because I'm not willing to fork out money for a data plan. Any solutions or suggestions would be greatly appreciated.
change the power mode for the wireless mode to 'Best Performance'. This worked for me. Start -> Settings -> Connections -> wireless lan -> Power mode -> Best Performance.
Work Around For Wi-Fi Problem
I have found a work around for this and have tested on my "Tilt" which works 100% for the windows mobile 6.1 rom. On your device go to start, settings, connections then click on the connection icon then manage existing connections. Create on new setting on top of Media Net settings which you will have two connections. Name it Cingular GPRS, Enter Cingular GPRS, then Cellular Line (GPRS, 3G) for your modem, click next access point name wap.cingular, click next then User name [email protected], Password encrypted. The only thing you need to do is when using the internet & text messaging to have settings set on bullet mark Cingular GPRS. When using MMS only check check bullet mark for Medit Net and have proxy settings enabled at all times which will not affect your Wi-Fi connection to browser the internet once you switch back to Cingular GPRS in your settings. https://www.wireless.att.com/suppor...tutorialsCategory=MEdia+Net&tutorialId=614410
Park said:
I have found a work around for this and have tested on my "Tilt" which works 100% for the windows mobile 6.1 rom. On your device go to start, settings, connections then click on the connection icon then manage existing connections. Create on new setting on top of Media Net settings which you will have two connections. Name it Cingular GPRS, Enter Cingular GPRS, then Cellular Line (GPRS, 3G) for your modem, click next access point name wap.cingular, click next then User name [email protected], Password encrypted. The only thing you need to do is when using the internet & text messaging to have settings set on bullet mark Cingular GPRS. When using MMS only check check bullet mark for Medit Net and have proxy settings enabled at all times which will not affect your Wi-Fi connection to browser the internet once you switch back to Cingular GPRS in your settings. https://www.wireless.att.com/suppor...tutorialsCategory=MEdia+Net&tutorialId=614410
Click to expand...
Click to collapse
Hi, I tried you solution several times, but still could not get the problem fixed. I guess I am just resolved to going back to the WM6 ROM. Thanks for the info though.
@abhijitray: I already tried changing the power settings when I first began having problems, so that's not it.
i have the same problem with my Tilt. But i found that when i connect to my PC with the USB cable, ActiveSync is on, my IE works fine. With Wifi connection, IE is still dead.
maybe an off topic question, but what does the new rom have that the original rom that came with the tilt doesn't? anyone have a link or something, or is it something like better batter performance? thx
i have tilt with the latest official WM6.1 ROM, and have no issues with Wifi.
Ok - here's my story.
I had a default WM 6.0 Official ROM Tilt and upgraded to ATT's 6.1. Immediately my WiFi stopped working. I waited for updates on this thread, and with my temper rising at such a poor release, I decided to go to Dutty's 6.1 Hybrid. Same thing - Wi-Fi didn't work. (To qualify, it would connect and get an IP address, but any attempt to access the net - ping, ftp, Gmaps, Activesync - would fail) I upgraded to the latest eMo radio and still didn't work. I scratched my head and decided to check my router. It's an older D-Link 802.11b and sadly the last firmware was released in 2005. I changed the settings on it to not use Turbo mode and voila, it connected. All happy and such.
But now the problem is slightly different. It will connect once, but after it disconnects (either because I manually turned off WiFi on the phone or the phone entered Standby mode) I cannot connect again. I literally have to reboot my router. This is great a home, but I worry when I have to use a public wifi hotspot. Any thoughts on that?
And yes, I have played around with the power settings.
Kojak
another thing I have noticed on my router is that my Tilt is not sending a hostname along with the DHCP request. Could that be the issue on the WiFi connection? I am wondering if that confuses the router.
Tom
I have the same problem too. tytn II with latest rom. At home with my old linksys which is a 802.11b device. If i disconnect wifi and then try to connect - the phone say - Unavailable. I notice that if i change the channel the phone connect just fine.... very strange
ps. sorry for my bad eng.
pasole said:
I have the same problem too. tytn II with latest rom. At home with my old linksys which is a 802.11b device. If i disconnect wifi and then try to connect - the phone say - Unavailable. I notice that if i change the channel the phone connect just fine.... very strange
ps. sorry for my bad eng.
Click to expand...
Click to collapse
I see the same here - I think that by changing the channel it reboots/resets the router and allows you to try again.
ps. don't worry about your english. If this board was in a different language, I am sure that most people here would not even be able to post a thing.
kojak_nyc said:
Ok - here's my story.
I had a default WM 6.0 Official ROM Tilt and upgraded to ATT's 6.1. Immediately my WiFi stopped working. I waited for updates on this thread, and with my temper rising at such a poor release, I decided to go to Dutty's 6.1 Hybrid. Same thing - Wi-Fi didn't work. (To qualify, it would connect and get an IP address, but any attempt to access the net - ping, ftp, Gmaps, Activesync - would fail) I upgraded to the latest eMo radio and still didn't work. I scratched my head and decided to check my router. It's an older D-Link 802.11b and sadly the last firmware was released in 2005. I changed the settings on it to not use Turbo mode and voila, it connected. All happy and such.
But now the problem is slightly different. It will connect once, but after it disconnects (either because I manually turned off WiFi on the phone or the phone entered Standby mode) I cannot connect again. I literally have to reboot my router. This is great a home, but I worry when I have to use a public wifi hotspot. Any thoughts on that?
And yes, I have played around with the power settings.
Kojak
Click to expand...
Click to collapse
Well, your problem sounds exactly the same as mine (WM6.1 official). Maybe I should have tried a public hotspot, but it just wouldn't work on my home network (I even cut off the encryption and made it open). I downgraded back to WM6 ROM and everything working fine, so I guess no WM6.1 for me.
It is definite a router by router problem. Had problems with the D-Link but I tried it on a Buffalo 802.11g router running Tomato firmware, and I had absolutely no problems. That being said, this could be either a:
802.11b problem?
D-Link problem?
Something must have changed in the WM 6.1 code from WM6.0 as it pertains to WiFi. If only it was as easy as a toggle setting to fix.
For me, it was the opposite. I could get WiFi to work at my office on Mobile 6.0, but I couldn't get my network at home to work. I have a Wireless-N network at home, and even though I set it to B-G only mode, it still wouldn't connect. As soon as I hit WM6.1, everything was fine.
Unfortunately, this happens more than one would think with Wireless network equipment.
kojak_nyc said:
It is definite a router by router problem. Had problems with the D-Link but I tried it on a Buffalo 802.11g router running Tomato firmware, and I had absolutely no problems. That being said, this could be either a:
802.11b problem?
D-Link problem?
Something must have changed in the WM 6.1 code from WM6.0 as it pertains to WiFi. If only it was as easy as a toggle setting to fix.
Click to expand...
Click to collapse
Kojak_nyc,
You hit it on the head. It is a router issue, although its not limited to the D-Link router because I have a 2wire HomePortal 1000HW and it also doesn't work. It is also on 802.11b, so that could also be the issue. Something must have changed between in the settings the WM6 and the WM6.1 upgrade. I'll go ahead an inform HTC of the issue (not that they'll do anything).
I believe that the once the tilt is updated to WM6.1, it no longer works on IEEE 802.11b.
I think this is a Dlink issue. I've got a linksys router at home and it connects to that fairly quickly. ssid on that isn't hidden cuz i've got vista machines that have a hard time connecting.
anyway, at work i've got a dlink di624, 802.11g, router and i've not been able to connect the kaiser to it. i think tomorrow i'll do what was suggested and just play around with the channels and find which works. the dlink's set to automatically choose the channel it uses so i'll hard code it for a channel i know the kaiser'll scan for and then see what happens.
if it doesn't work i'll juts keep using the 3g connection... i do have 6GB/mo and haven't come anywhere near using it up.
Experienced similar problem just now. I just upgraded to WM 6.1 and my WiFi connection's been unstable since last night. I have a wireless router with excellent signal on my room and enjoys streaming video before I upgraded to WM 6.1. When I reset the phone it restored WiFi connection again.
Hope you could share some tweaks to resolve this problem.
Thanks.
Hi,
ive installed a windows mobile 6.5 rom on my xperia and now it wont connect to my belkin wifi router it keeps telling me the key is wrong when i know it isnt
any help?
i had the same issue even with my P1i, and my x1 6.1 stock lol, so i removed the password and left it open, it connects perfectly
wifi problem on wm6.5 imate jamin
guys can you help me out that how do i make a stable connection of wifi on my wm6.5 imate jamin because when it's connected after 1 to 2 mins it starts searching again which causes connection lose during my work
it would be appriciated if anyone helps me because i'm stuck with this wifi problem