Wizard G3 - Rom upgrade went bad - can't connect with AS - 8125, K-JAM, P4300, MDA Vario Software Upgrading

I've tried installing the Superrom 1.1 as noted in this thread: http://forum.xda-developers.com/showthread.php?t=288074
After the first boot it seemed to be working okay untill it rebooted all by itself.. Since then it doesn't work normal anymore.
At this point I can't get it to connect with ActiveSync, and it also doesn't respond to the regular charger. If I load it into bootloader mode and my pc gave at that point the message there was a ppc connected to the usb port. I couldn't get the MTTY_updateROM.exe app to work properly, imo..
I've unpacked it, opened it and chose the \\.\WCEUSBSH001 - up untill this point it all seemed to go fine. than I typed in the "r2sd all" and hit enter. It immediately showed the Cmd> ... It didn't give any other command whatsoever.. Now I still can't connect it and can't get it back to bootloader mode.
I've done the CID unlock first with the app found on this site (lokiwiz02b) and that went succesfully. After that I encountered no problems with the Superrom upgrade proces..
Can anyone give me some advice and help me out with this problem..?
I can get it to boot up. Although not really normal... It gives the 'splash screen', than it "fades" to white/grey and boots up again.. than it goes all the way (most of the time). After I leave it on for a while it gives the "fade-to-white" and boots up again...
If someone could please help me out..?
edit:
This is what it gives during the "splash screen" with the ppctuning.org in the right bottom of the "Windows Mobile loading...." screen:
IPL 1.06
SPL 1.06
OS 2.26.10.2

The problem is your bootloader. You should have upgraded to a stock rom with ipl/spl 2.x included. Never flash a AKU2 rom with a 1.x bootloader.
Try reflashing your device with the 1.x rom provided in the CID-unlocking thread, then upgrade to a rom with ipl/spl 2.x

Thanks for your advice..!
Sorry to be a noob on this... I really appreciate your help (and that of others.. )
The problem is that I can't get it connected with active sync.. seems as if the usb port on my phone is broke or something..?
edit:
update..: I got it in bootloader mode again (yay!) but now I get this error when doing the Romupdate app:
CMD55 failed
R2SDBackup() SD card initialize fail !!
Is it possible it all goes to a faulty mini SD card?

Remove your SC and try again.

Dr Puttingham said:
Remove your SC and try again.
Click to expand...
Click to collapse
I have removed the simcard (I suppose you meant that.. ) and still no improvement.. (when I remove the mini-SD it obiously gives the error pls. insert SD card...
It still gives the "CMD55 failed" error and I can't connect regular to AS...

gvink said:
I have removed the simcard (I suppose you meant that.. ) and still no improvement.. (when I remove the mini-SD it obiously gives the error pls. insert SD card...
It still gives the "CMD55 failed" error and I can't connect regular to AS...
Click to expand...
Click to collapse
Humor us and downgrade to the 1.05, reunlock cid and sim and install the tmobile 2.26. Link is in my sig.

Dr Puttingham said:
Humor us and downgrade to the 1.05, reunlock cid and sim and install the tmobile 2.26. Link is in my sig.
Click to expand...
Click to collapse
I wish I could but I can't get a working Active Sync conecting up & running.. Correct me if I'm wrong, but as far as I understand I need that to unlock/downgrade/upgrade..?

ok... You don't need activesync to do a ROM upgrade/downgrade...
Push the two buttons on the right side while pushing the reset button. That should bring you to the bootloader screen. Make sure that your SD-card slot is empty, and plug in the USB-cord. Now the word USB should appear in the lower right corner. NOW, start the RUU and install the 1.X rom.

_Nomad_ said:
ok... You don't need activesync to do a ROM upgrade/downgrade...
Push the two buttons on the right side while pushing the reset button. That should bring you to the bootloader screen. Make sure that your SD-card slot is empty, and plug in the USB-cord. Now the word USB should appear in the lower right corner. NOW, start the RUU and install the 1.X rom.
Click to expand...
Click to collapse
YOU are AWESOME!!
i had the same problem and i now am able to do the downgrade!

mikey411 said:
YOU are AWESOME!!
i had the same problem and i now am able to do the downgrade!
Click to expand...
Click to collapse
YAY! Same response here! After looking to the beautiful half-full beer glas it works like a charm again..!
Thank you!

yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?

mikey411 said:
yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?
Click to expand...
Click to collapse
You talking to me?

Dr Puttingham said:
You talking to me?
Click to expand...
Click to collapse
whoaa.. how did you come to this conclusion?

mikey411 said:
whoaa.. how did you come to this conclusion?
Click to expand...
Click to collapse
Because I HAVE been known to post sarcastic remarks ....
A little thin skinned today ..
No offense taken then.

mikey411 said:
yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?
Click to expand...
Click to collapse
Mikey, I'm going to suggest that you refrain from such comments. If you poke at a sleeping dragon, nobody will listen to you cry about getting burned.
You got your help without a single smart arse post, no need to ask for negative attention.
BTW, my horse isn't too high for me to climb down off it from time to time....

kyphur said:
Mikey, I'm going to suggest that you refrain from such comments. If you poke at a sleeping dragon, nobody will listen to you cry about getting burned.
You got your help without a single smart arse post, no need to ask for negative attention.
BTW, my horse isn't too high for me to climb down off it from time to time....
Click to expand...
Click to collapse
pardon me.. but isn't what I said the truth?

mikey411 said:
pardon me.. but isn't what I said the truth?
Click to expand...
Click to collapse
The truth is subjective and colored by each observer's point of view.
I made a valid point and I would suggest you remember it. We are working to get these issues under control and the last thing we need is someone instigating. I will beat down any post that looks to start flaming, either by attacking or inviting attack.
Now, let me put down my moderating staff and finish my sandwich.

kyphur said:
The truth is subjective and colored by each observer's point of view.
I made a valid point and I would suggest you remember it. We are working to get these issues under control and the last thing we need is someone instigating. I will beat down any post that looks to start flaming, either by attacking or inviting attack.
Now, let me put down my moderating staff and finish my sandwich.
Click to expand...
Click to collapse
point taken..

I cannot get this to work. I keep getting error 264. Does that mean I am screwed? I can access the bootloader so I am think there is still hope for me.

Related

How to put Herald in boot loader mode ?

Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
If you searched a lil bit more you'll find that piece of info in herehttp://wiki.xda-developers.com/index.php?pagename=Herald_Resets
in the Wiki herald section
sandibad said:
Hello,
I've searched a lot how to put the Herald in the boot loader mode.
Please, help me.
Thank you advance.
LAter edit: i found out: i had to keep pressed the camera button lol
Click to expand...
Click to collapse
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Looking for
In fact, i read houdreds of time all the posts... at 5 AM...
Because by Herald was in the "white screen" and i was desperate...loking for solution ...
In fact, I have to wait for the official WM6 because that one didn't worked for me.
Thks for assistance.
papamopps said:
and in nearly everypost about unbricking and flashing.
Pleas read, read, read.
and btw: commmanager + camera + softreset.
Click to expand...
Click to collapse
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
nugift said:
No need to press comm.button. Just press camera and softreset at once, release the softreset first than camera button. That's all!
Click to expand...
Click to collapse
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
papamopps said:
OK. Thanks
BTW - my device is unbricked. BUT it was made by repairservice - for warenty. lol.
I´m happy again. Hehe
Click to expand...
Click to collapse
Damn you did not have to pay?? sweet!
Newbie here.....
I have an HTC P4350. During the upgrade, there was a disconnect with my computer to the phone, now I have that colored screen when I start up. I tried the hard and soft reset and also the Boot loader method.
Anyone have any other suggestions?
Do you think if the phone went back to HTC, they would be able to fix it?
Thanks for your help
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
R_phAn said:
You should be able to flash the original RUU when you're in bootloader mode ('the three colored screen') and connected to the PC with your USB cable. Worked for me anyways.
Just put your phone in bootloader mode, connect it to your computer and run the RUU.
Click to expand...
Click to collapse
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
passmoregas23 said:
The problem is that it won't connect to the computer via activeSync, until that happens the phone cannot be updated.
Click to expand...
Click to collapse
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
dcmtnbkr said:
Have you tried it before you said that it would not work? Seriously? When in bootloader mode, the computer doesn't connect via activesync (how could it, there is no operating system on the phone). Get into bootloader mode, connect the phone to the computer (yes, i know activesync doesn't show a connection at this point) and run the stock RUU for your device. If this does not work, then there is something seriously wrong with your device.
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
To add to this, when in bootloader and plugged into your PC, it will say "USB" at the bottom. That's how you know it's connected properly.
If you're having troubles and you're running Vista...
http://www.modaco.com/RUU-Vista-done-u-t252977.html
dcmtnbkr said:
I honestly wish people would try things first before claiming that it didnt work, I know i have not posted that much, but that is because i search the forums for the questions i have, rather than wasting the time of the people who are doing all the cooking (for free might i add) and getting on their nerves.
Click to expand...
Click to collapse
Dude, I have searched for a resolve to my problem, and I do appreciate peoples help. I don't waste time of good Samaritans. I did run the RRU and I received an 260 error, which is another topic which I did research on as well.
I'm going to send the phone back to HTC and let them fix it.

[Help]Unlocking Cingular 8125

Hey im new to these forums and just need help unlocking my Cingualr 8125 or put a different Rom liek the xda windows mobile 6.0. Im folowing the steps but like when i open "ROMupdateutility.exe" I follow the steps and when it starts my 8125 goes to like bootmode? It has 3 colors on the screen
red greedn and blue and then on the ROMUPDate utlity i got error 300...i tryed like so many times i need help thnx =[
EDIT : the error says error 300 invalid update tool.... "This error message will appear when you use the incorrect RUU to upgrade. Please make sure you use the correct RUU version to upgrade." where do i get the correct RUU then?...
Also found out that its a G4 because of the Ip number or w/e because it has 3 zeros then a 1 for example .0001
[Help] Unlocking Cingular 8125
Hey im new to these forums and i need help unlocking my Cingular 8125
From what ive seen on these forums my phone is G4 Because it has xxx1 at the end of the ip or w/e that **** is. I would gladly appreciate it if someone would help me unlock my G4.One of my friends has his unlocked it looks like Vista and it has all these sweet programs. Since i just got mine its g4 I guess..and since he got him like 2 months bevfore me maybe his was g3 so it was easy...
This is probably why so many people flame noobs. cause of questions like this. If you have any sort of I.Q in you you would have checked this link out http://forum.xda-developers.com/showthread.php?t=293480 its the very first post. good luck
deviusdragger said:
This is probably why so many people flame noobs. cause of questions like this. If you have any sort of I.Q in you you would have checked this link out http://forum.xda-developers.com/showthread.php?t=293480 its the very first post. good luck
Click to expand...
Click to collapse
Noob, i already checked that one. Its stickied why wouldnt i not check it before posting this thread?
The link's on that Thread are dead. They dont work anymore ***. Lol
Can't we all just get along? Let's keep things nice-nice, okay?
Anyhow, chaos36 it's really important to read up on this site before posting. All the answers are readily available (with some time and patience).
Here's a quick guideline ...
1. Your first stop should be here (the wiki)
All the information and links to get the most out of your device
2. How to SIM unlock your phone, look here.
3. How to flash any ROM other than your carrier's, here
4. Enjoy!
But just a bit of friendly advice for you in the future. Read and search all you can, then if you can't find what you're looking for, read and search some more before posting.
This site is a great place for developers, hobbyists, and enthusiasts. It's not a "helpdesk". But as long as you help yourself first, you'll find a lot of great (nice) people that will help you along your way.
Good luck and have fun!
http://forum.xda-developers.com/showthread.php?t=293480
Thnx..i ****ed up when i turn on my 8125 it stays at cingular raising the bar witht he ipl and spl number -.- please hel and ty.
chaos36 said:
Thnx..i ****ed up when i turn on my 8125 it stays at cingular raising the bar witht he ipl and spl number -.- please hel and ty.
Click to expand...
Click to collapse
Can you still get into the bootloader screen? (the red/blue/green screen)
To get into the bootloader you need to HOLD the camera button and tap the reset button.
Yes im in that screen right now if you mean the screen thtat has 3 stips a red then green then blue?
Now what do i do when im there?
chaos36 said:
Yes im in that screen right now if you mean the screen thtat has 3 stips a red then green then blue
Click to expand...
Click to collapse
Alright, this is a good example (one that we've all seen over and over again here) of how not to jump into flashing your phone without reading everything thoroughly.
Stay in the bootloader screen, keep your USB cord plugged in and reflash your original carrier's ROM. That will get you back to factory specs.
Then, don't try flashing anything else UNTIL you read everything I mentioned in the previous post first, at least a couple times through.
Just some advice
TaurusBullba said:
Alright, this is a good example (one that we've all seen over and over again here) of how not to jump into flashing your phone without reading everything thoroughly.
Stay in the bootloader screen, keep your USB cord plugged in and reflash your original carrier's ROM. That will get you back to factory specs.
Then, don't try flashing anything else UNTIL you read everything I mentioned in the previous post first, at least a couple times through.
Just some advice
Click to expand...
Click to collapse
How do i reflash the original carriers ROM?
And thank you for helping me out.
[Do you got AIM would be much easier and qicker to discuss thiss.]
chaos36 said:
How do i reflash the original carriers ROM?
And thank you for helping me out.
Click to expand...
Click to collapse
Well, glad to help. To reflash your original carriers ROM, you need to download it from their website and execute it.
Ok i got a cingular 8125. So to download it i go to Cingualr.com?...Sorry for being so noob and do you got AIm will be much easier for you to help me there ty.
I'm actually about to hit the sack. But you can get the Cingular ROM here. Just download and install it and you'll be good.
Good luck!
Wow you gave me a direct link. Thank you for all your help! Do you got AIM incase i cant figure out how to do this? maybe u can help me out tomorrow thnx for all your time and help.
Taurus pretty much held your hand and walked you thru it. You should be fine after this point. And if some of the links arent working, just let some of the mods now and they will take care of all that stuff. So good luck with the flashing.
deviusdragger said:
Taurus pretty much held your hand and walked you thru it. You should be fine after this point. And if some of the links arent working, just let some of the mods now and they will take care of all that stuff. So good luck with the flashing.
Click to expand...
Click to collapse
Yes he did and it was nice of him for doing that to me. My 8125 is fine now..but the link you gave me for the flash's are dead the links dont work =[

[Walkthrough] How to fix your bricked phone

So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse
papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...
Too bad it'll be stated a million more times afterwards too.
falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol
ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!
ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?
ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider
Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.
The instructions to do this are actually in my newbie thread. Which is a sticky.
TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...
help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......
Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.
And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec
If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.
Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.

re flashing

hi,
i re flashed my phone last week and want to do it again as i have tried all sorts of programs and removed some and i think all of this has slowed my phone down and i have been getting a few problems so what i want to know is can i just re flash or do i have to do HardSPL again before i re flash ?
Tony
morpheus95 said:
hi,
i re flashed my phone last week and want to do it again as i have tried all sorts of programs and removed some and i think all of this has slowed my phone down and i have been getting a few problems so what i want to know is can i just re flash or do i have to do HardSPL again before i re flash ?
Tony
Click to expand...
Click to collapse
did you already hardspl? If it was successful its a one time only operation. You should not have to do it again.
P1Tater said:
did you already hardspl? If it was successful its a one time only operation. You should not have to do it again.
Click to expand...
Click to collapse
hello,
i did do the hardSPL but i was getting the white screen and had to do the other method which i forget which why it was but i am running Duttys rom at the moment.
i see that Dutty has a new Rom out now anyway so i might as well give that a try.
i want to use pocket plus and pocket weather on this ROM should that be ok
Enter bootloader mode for me and tell me exactly what it says.
Hold donw the camera button and at the same time insert the stylus in the reset hole until you enter bootloader
KAIS130 MFG
SPL-1.0.olipof
CPLD-8
morpheus95 said:
KAIS130 MFG
SPL-1.0.olipof
CPLD-8
Click to expand...
Click to collapse
your good, rock on.
ok thanks,
so all i need to do then is like before download the new Rom and open it ?
morpheus95 said:
ok thanks,
so all i need to do then is like before download the new Rom and open it ?
Click to expand...
Click to collapse
Yep. just flash away.
thanks for your help
P1Tater said:
Yep. just flash away.
Click to expand...
Click to collapse
That's 2 consecutive threads I've read with your posts in them and not a flame in sight - man, you need a holiday
ach2 said:
That's 2 consecutive threads I've read with your posts in them and not a flame in sight - man, you need a holiday
Click to expand...
Click to collapse
You might be on to something. Actually, upon suggestion by one of the mods, I have been updating the Kaiser FAQ and I realized it was quite hard to follow since more than half of it wasnt in Q&A format. I sure could use some help with it. Im about to pull my hair out. I might go on a rampage here shortly though.
P1Tater said:
You might be on to something. Actually, upon suggestion by one of the mods, I have been updating the Kaiser FAQ and I realized it was quite hard to follow since more than half of it wasnt in Q&A format. I sure could use some help with it. Im about to pull my hair out. I might go on a rampage here shortly though.
Click to expand...
Click to collapse
I'm a bit of a twat at some of this stuff, but if you need help - maybe easy stuff like proof reading etc, send me a pm.

Hard spl in detail Wing/Herald

This is for ne one that is looking for detail in making their Wing/Herald hard spl'd
Please do not get mad at me if it does not work.. But there are a ton of success stories with flashing Wing/Herald to Hard SPL..
#1:
Ok first check your ipl and spl.. You can do this by entering bootloader. bootloader (push the pin hole right under volume slide and hold camera button) you will then enter bootloader.. It looks like 3 color bars and say's ipl 4.xxxxx whatever and spl 4.xxxxx same.. Whatever the 4.xxx is thats what ipl and spl you are.. In order to become hard spl you must at least 4. and higher.. So if you see a 4 then your good..
#2:
Ok now that we have checked, soft reset your phone again and let it load.. This will get you out of bootloader and back to normal mode.. I was very careful on flashing.. So i always reverted back to oem rom.. So get the oem Wing rom or Herald rom.. If you can't find it let me know because i have it.. So just flash oem and let it be stock rom..
#3:
Ok now is getting ready to start from the very beginning.. Now if you have the 3 cabs (canonyang.cab, aserpolicy.cab, disablesecurity.cab) just install them in order as writen . After they were successfully installed soft rest your phone again..
#4:
Ok now we start the flash.. Its a scary few moments lol.. But very worth it.. Make sure you are synced and connected to your comp.. I also was extra careful by resetting my comp and making sure all windows were closed and made it so windows weren't open.. But i was extra careful Check the circle and make sure its green or if you have vista it'll be the pda icon lite up.. now open your hard spl folder (the rar. or folder that you dl'd for from the main page) and click on ROMUpdateUtility. Now just wait for it to finish the flash.
- If all goes well then it will come up something like Yang something something.. You will see a dif splash due to you dl'ing a new rom that makes your phone hard spl'd. Let it finish and your good.. Soft reset and enter bootloader and see if spl is 4.70 yang.. If so congrats your hard spl'd!!!!!! fo sho...
* Now to flash other roms all you have to do is get your oem rom and right click on it.. Extract it and you will see its contents.. Among its contents delete the spl.nbh file. Not the ruu.nbh.. Now you click romupdateutility.. I would make the extracted oem a special folder because this is now your new flashcenter.. Ne time you would like to flash a new rom all you have to do is simply replace the rom .nbh of your liking in this folder that you made and run romupdate.. All done.. Easy flashing.. lol.. Welcome to hard spl world!!! Now you can flash at ease.. Ne Herald/ Wing rom you have is now flashable except roms designed for micro sd cards (trasflash cards) Just use the .nbh files..
Please if you are are not ok with my instructions and wish special help(detailed help) with this put it on this thread. Others will learn from others concerns.. Even if the ? has been asked a million times still ask.. Please ask ?'s before flashing if something does not go with instructions..
Once again i'm not responsible for ne thing that happens to your wing/herald.. I am simply trying to help in-detail and be at assistance in ne way possible..
This is the dl from the orginal Hard SPL page. It contains everything thing you need.. (cab. files, .nbh for flahsing and romutility for flashing)
Give credit to Papamopps's for starting the Hard SPL thread
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
This is the oem tmobile rom update:
http://rapidshare.com/files/148795008/TMo_Wing_RUU_Update_4.26.531.4.exe
Good manual! thanks!
ruebyi said:
Good manual! thanks!
Click to expand...
Click to collapse
no problem.. i had a friend in a dif thread needing help with hard spl and was looking for detail.. so here it is.. plus ill be as much support as i can be.
trust me if you follow those steps it will work and you will be on your way to great things
I have a question, I hard spl'd my wing before but since than I got another one since it broke. Do I have to install the cab files in a special order? It seems that I remember doing this in a special order before. I hope I did not over look this question in your thread. Good post by the way.
lmyers10 said:
I have a question, I hard spl'd my wing before but since than I got another one since it broke. Do I have to install the cab files in a special order? It seems that I remember doing this in a special order before. I hope I did not over look this question in your thread. Good post by the way.
Click to expand...
Click to collapse
On the original thread there is a specific order.. canonyang.cab, aserpolicy.cab, disablesecurity.cab.. I had a second wing and did not fallow this order.. i just did it from bottom to top in alphabetical order. i kinda didnt care with the second wing thou.. i would do as the first theard says.. i totally forgot that there is an order.. i will edit.. thanks..
iPhone iWing said:
On the original thread there is a specific order.. canonyang.cab, aserpolicy.cab, disablesecurity.cab.. I had a second wing and did not fallow this order.. i just did it from bottom to top in alphabetical order. i kinda didnt care with the second wing thou.. i would do as the first theard says.. i totally forgot that there is an order.. i will edit.. thanks..
Click to expand...
Click to collapse
I wasnt busting your chops ,just wanted to make sure I remembered right. I will be using your directions as a guideline as I am getting ready to hard spl my phone again.
lmyers10 said:
I wasnt busting your chops ,just wanted to make sure I remembered right. I will be using your directions as a guideline as I am getting ready to hard spl my phone again.
Click to expand...
Click to collapse
O no man i wasn't coming close to taking it like that.. It was a big reminder!! Thank you.. Like i said thou i didnt do them in order on my other wing and it worked without a prob.. But do as recommended now.. I put that they need to be in the order i have posted.. Thanks.. I hope your hard spl goes great!!!
fo_sho..
thanks these are great instruction.and i believe anybody should b able to hard spl afer reading these directions...but hey who knows
Thanks it worked perfect
Ditto here. Thank you very, very much. Good instructions!
One little thing: "aserpolicy.cab" is actually "ASerg Policies.CAB" and "disablesecurity.cab" is "Disable_Security.cab" in the OEM ROM you provided a link to.
I just got a used Wing off Ebay. My IPL is 4.10.0002 and my SPL is 4.10.0000 and when I try to HardSPL I get to where the progress bar is but then it says it can't communicate with my PDA/PHone and dies on me.
I installed the CAB files in the order stated then soft reset then ran the ROM UPdate Utility. ActiveSync is active but it says it can't communicate. Did I do something wrong?
Thanks for any help.
*** Edit*** Got this figured out. I needed to go to Settings->Connections->USB to PC and check the box for Advanced Communications then run the ROM Update Utility
Lance
I followed these instructions perfectly, I got the new "yang" splash, I checked the bootloader and it confirms the spl is 4.70 yang but when i soft reset to get out of the bootloader and try to start the phone up it says:
"Error-Device start up failed due to sudden loss of power. Please click Yes or No to continue."
But there wasnt a power loss, and it wont let me click yes or no. Anyone know what happened and what I should do?
EDIT: Never mind, I got it fixed.
chaotic646 said:
I followed these instructions perfectly, I got the new "yang" splash, I checked the bootloader and it confirms the spl is 4.70 yang but when i soft reset to get out of the bootloader and try to start the phone up it says:
"Error-Device start up failed due to sudden loss of power. Please click Yes or No to continue."
But there wasnt a power loss, and it wont let me click yes or no. Anyone know what happened and what I should do?
EDIT: Never mind, I got it fixed.
Click to expand...
Click to collapse
Maybe post how in case this happens to someone else?
iPhone iWing said:
This is for ne one that is looking for detail in making their Wing/Herald hard spl'd
Please do not get mad at me if it does not work.. But there are a ton of success stories with flashing Wing/Herald to Hard SPL..
#1:
Ok first check your ipl and spl.. You can do this by entering bootloader. bootloader (push the pin hole right under volume slide and hold camera button) you will then enter bootloader.. It looks like 3 color bars and say's ipl 4.xxxxx whatever and spl 4.xxxxx same.. Whatever the 4.xxx is thats what ipl and spl you are.. In order to become hard spl you must at least 4. and higher.. So if you see a 4 then your good..
#2:
Ok now that we have checked, soft reset your phone again and let it load.. This will get you out of bootloader and back to normal mode.. I was very careful on flashing.. So i always reverted back to oem rom.. So get the oem Wing rom or Herald rom.. If you can't find it let me know because i have it.. So just flash oem and let it be stock rom..
#3:
Ok now is getting ready to start from the very beginning.. Now if you have the 3 cabs (canonyang.cab, aserpolicy.cab, disablesecurity.cab) just install them in order as writen . After they were successfully installed soft rest your phone again..
#4:
Ok now we start the flash.. Its a scary few moments lol.. But very worth it.. Make sure you are synced and connected to your comp.. I also was extra careful by resetting my comp and making sure all windows were closed and made it so windows weren't open.. But i was extra careful Check the circle and make sure its green or if you have vista it'll be the pda icon lite up.. now open your hard spl folder (the rar. or folder that you dl'd for from the main page) and click on ROMUpdateUtility. Now just wait for it to finish the flash.
- If all goes well then it will come up something like Yang something something.. You will see a dif splash due to you dl'ing a new rom that makes your phone hard spl'd. Let it finish and your good.. Soft reset and enter bootloader and see if spl is 4.70 yang.. If so congrats your hard spl'd!!!!!! fo sho...
* Now to flash other roms all you have to do is get your oem rom and right click on it.. Extract it and you will see its contents.. Among its contents delete the spl.nbh file. Not the ruu.nbh.. Now you click romupdateutility.. I would make the extracted oem a special folder because this is now your new flashcenter.. Ne time you would like to flash a new rom all you have to do is simply replace the rom .nbh of your liking in this folder that you made and run romupdate.. All done.. Easy flashing.. lol.. Welcome to hard spl world!!! Now you can flash at ease.. Ne Herald/ Wing rom you have is now flashable except roms designed for micro sd cards (trasflash cards) Just use the .nbh files..
Please if you are are not ok with my instructions and wish special help(detailed help) with this put it on this thread. Others will learn from others concerns.. Even if the ? has been asked a million times still ask.. Please ask ?'s before flashing if something does not go with instructions..
Once again i'm not responsible for ne thing that happens to your wing/herald.. I am simply trying to help in-detail and be at assistance in ne way possible..
This is the dl from the orginal Hard SPL page. It contains everything thing you need.. (cab. files, .nbh for flahsing and romutility for flashing)
Give credit to Papamopps's for starting the Hard SPL thread
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
This is the oem tmobile rom update:
http://rapidshare.com/files/148795008/TMo_Wing_RUU_Update_4.26.531.4.exe
Click to expand...
Click to collapse
Awesome. I was worried about doing this because everything seemed out of date and etc on here but I figured the hell with it, it's been months and so many hours this week and it worked. Thanks. I was a little worried about the spl because it looked like an older version and said wm6 and not 6.1. Well everything worked out great, thanks for this. After hours and days of reading every thing I could, this was the only that did not leave me with too many unanswered questions making me worried about doing this.
*UPDATE* So I I did another one today (or tried) and kept getting that 260 error and don't know why yet (I know; it is some place in the forums) and after having it do it about 5 times I checked (unlike you said to) and it never updated the spl etc I was in a hurry but I don't think the error was my fault. But now I have a question: What exactly are the 3 cab files for? At first I thought that was what did the hard spl but then after doing it and reading this again (I learn by doing not reading) I realizied it is not. And second question is: Why does it have to be flashed with that ROM to hard spl it?
apathetic said:
Maybe post how in case this happens to someone else?
Click to expand...
Click to collapse
It did allow me to click yes, I was just trying to touch the yes with my stylus but I had to click the left soft key. I dont know what caused the error but it seems to be working fine now and Ive successfully flashed 4 different roms.
chaotic646 said:
It did allow me to click yes, I was just trying to touch the yes with my stylus but I had to click the left soft key. I dont know what caused the error but it seems to be working fine now and Ive successfully flashed 4 different roms.
Click to expand...
Click to collapse
Oh ok. I did 3 today and still did not see that (tg)
Hi!
Thanks for all the explanations.
My IPL is 4.18.0002 and SPL4.18.0000.
My phone is locked by a brazilian cell commpany TIM. Do I need to unlock my herald before to do a hard spl?
Thanks in advance
Gorbo
Hi Gordo, I am from Porto Alegre too and I hard-spled ok here.
You dont need to unlock before to do a hard spl.
Thanks.
apathetic said:
Maybe post how in case this happens to someone else?
Click to expand...
Click to collapse
I have done the same yesterday ... the thing was I've forgot the storage card in the phone. There was mess of previous installation (mostly WM5). Today I've made clear installation of the official WM6 with the card out of slot. It is working perfect now.

Categories

Resources