re flashing - Tilt, TyTN II, MDA Vario III General

hi,
i re flashed my phone last week and want to do it again as i have tried all sorts of programs and removed some and i think all of this has slowed my phone down and i have been getting a few problems so what i want to know is can i just re flash or do i have to do HardSPL again before i re flash ?
Tony

morpheus95 said:
hi,
i re flashed my phone last week and want to do it again as i have tried all sorts of programs and removed some and i think all of this has slowed my phone down and i have been getting a few problems so what i want to know is can i just re flash or do i have to do HardSPL again before i re flash ?
Tony
Click to expand...
Click to collapse
did you already hardspl? If it was successful its a one time only operation. You should not have to do it again.

P1Tater said:
did you already hardspl? If it was successful its a one time only operation. You should not have to do it again.
Click to expand...
Click to collapse
hello,
i did do the hardSPL but i was getting the white screen and had to do the other method which i forget which why it was but i am running Duttys rom at the moment.

i see that Dutty has a new Rom out now anyway so i might as well give that a try.
i want to use pocket plus and pocket weather on this ROM should that be ok

Enter bootloader mode for me and tell me exactly what it says.
Hold donw the camera button and at the same time insert the stylus in the reset hole until you enter bootloader

KAIS130 MFG
SPL-1.0.olipof
CPLD-8

morpheus95 said:
KAIS130 MFG
SPL-1.0.olipof
CPLD-8
Click to expand...
Click to collapse
your good, rock on.

ok thanks,
so all i need to do then is like before download the new Rom and open it ?

morpheus95 said:
ok thanks,
so all i need to do then is like before download the new Rom and open it ?
Click to expand...
Click to collapse
Yep. just flash away.

thanks for your help

P1Tater said:
Yep. just flash away.
Click to expand...
Click to collapse
That's 2 consecutive threads I've read with your posts in them and not a flame in sight - man, you need a holiday

ach2 said:
That's 2 consecutive threads I've read with your posts in them and not a flame in sight - man, you need a holiday
Click to expand...
Click to collapse
You might be on to something. Actually, upon suggestion by one of the mods, I have been updating the Kaiser FAQ and I realized it was quite hard to follow since more than half of it wasnt in Q&A format. I sure could use some help with it. Im about to pull my hair out. I might go on a rampage here shortly though.

P1Tater said:
You might be on to something. Actually, upon suggestion by one of the mods, I have been updating the Kaiser FAQ and I realized it was quite hard to follow since more than half of it wasnt in Q&A format. I sure could use some help with it. Im about to pull my hair out. I might go on a rampage here shortly though.
Click to expand...
Click to collapse
I'm a bit of a twat at some of this stuff, but if you need help - maybe easy stuff like proof reading etc, send me a pm.

Related

Wizard G3 - Rom upgrade went bad - can't connect with AS

I've tried installing the Superrom 1.1 as noted in this thread: http://forum.xda-developers.com/showthread.php?t=288074
After the first boot it seemed to be working okay untill it rebooted all by itself.. Since then it doesn't work normal anymore.
At this point I can't get it to connect with ActiveSync, and it also doesn't respond to the regular charger. If I load it into bootloader mode and my pc gave at that point the message there was a ppc connected to the usb port. I couldn't get the MTTY_updateROM.exe app to work properly, imo..
I've unpacked it, opened it and chose the \\.\WCEUSBSH001 - up untill this point it all seemed to go fine. than I typed in the "r2sd all" and hit enter. It immediately showed the Cmd> ... It didn't give any other command whatsoever.. Now I still can't connect it and can't get it back to bootloader mode.
I've done the CID unlock first with the app found on this site (lokiwiz02b) and that went succesfully. After that I encountered no problems with the Superrom upgrade proces..
Can anyone give me some advice and help me out with this problem..?
I can get it to boot up. Although not really normal... It gives the 'splash screen', than it "fades" to white/grey and boots up again.. than it goes all the way (most of the time). After I leave it on for a while it gives the "fade-to-white" and boots up again...
If someone could please help me out..?
edit:
This is what it gives during the "splash screen" with the ppctuning.org in the right bottom of the "Windows Mobile loading...." screen:
IPL 1.06
SPL 1.06
OS 2.26.10.2
The problem is your bootloader. You should have upgraded to a stock rom with ipl/spl 2.x included. Never flash a AKU2 rom with a 1.x bootloader.
Try reflashing your device with the 1.x rom provided in the CID-unlocking thread, then upgrade to a rom with ipl/spl 2.x
Thanks for your advice..!
Sorry to be a noob on this... I really appreciate your help (and that of others.. )
The problem is that I can't get it connected with active sync.. seems as if the usb port on my phone is broke or something..?
edit:
update..: I got it in bootloader mode again (yay!) but now I get this error when doing the Romupdate app:
CMD55 failed
R2SDBackup() SD card initialize fail !!
Is it possible it all goes to a faulty mini SD card?
Remove your SC and try again.
Dr Puttingham said:
Remove your SC and try again.
Click to expand...
Click to collapse
I have removed the simcard (I suppose you meant that.. ) and still no improvement.. (when I remove the mini-SD it obiously gives the error pls. insert SD card...
It still gives the "CMD55 failed" error and I can't connect regular to AS...
gvink said:
I have removed the simcard (I suppose you meant that.. ) and still no improvement.. (when I remove the mini-SD it obiously gives the error pls. insert SD card...
It still gives the "CMD55 failed" error and I can't connect regular to AS...
Click to expand...
Click to collapse
Humor us and downgrade to the 1.05, reunlock cid and sim and install the tmobile 2.26. Link is in my sig.
Dr Puttingham said:
Humor us and downgrade to the 1.05, reunlock cid and sim and install the tmobile 2.26. Link is in my sig.
Click to expand...
Click to collapse
I wish I could but I can't get a working Active Sync conecting up & running.. Correct me if I'm wrong, but as far as I understand I need that to unlock/downgrade/upgrade..?
ok... You don't need activesync to do a ROM upgrade/downgrade...
Push the two buttons on the right side while pushing the reset button. That should bring you to the bootloader screen. Make sure that your SD-card slot is empty, and plug in the USB-cord. Now the word USB should appear in the lower right corner. NOW, start the RUU and install the 1.X rom.
_Nomad_ said:
ok... You don't need activesync to do a ROM upgrade/downgrade...
Push the two buttons on the right side while pushing the reset button. That should bring you to the bootloader screen. Make sure that your SD-card slot is empty, and plug in the USB-cord. Now the word USB should appear in the lower right corner. NOW, start the RUU and install the 1.X rom.
Click to expand...
Click to collapse
YOU are AWESOME!!
i had the same problem and i now am able to do the downgrade!
mikey411 said:
YOU are AWESOME!!
i had the same problem and i now am able to do the downgrade!
Click to expand...
Click to collapse
YAY! Same response here! After looking to the beautiful half-full beer glas it works like a charm again..!
Thank you!
yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?
mikey411 said:
yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?
Click to expand...
Click to collapse
You talking to me?
Dr Puttingham said:
You talking to me?
Click to expand...
Click to collapse
whoaa.. how did you come to this conclusion?
mikey411 said:
whoaa.. how did you come to this conclusion?
Click to expand...
Click to collapse
Because I HAVE been known to post sarcastic remarks ....
A little thin skinned today ..
No offense taken then.
mikey411 said:
yup.. _Nomad_ was straight to the point and really helpful.. instead of sarcastic comments from others i won't mention..
some people should get off their high horses?
Click to expand...
Click to collapse
Mikey, I'm going to suggest that you refrain from such comments. If you poke at a sleeping dragon, nobody will listen to you cry about getting burned.
You got your help without a single smart arse post, no need to ask for negative attention.
BTW, my horse isn't too high for me to climb down off it from time to time....
kyphur said:
Mikey, I'm going to suggest that you refrain from such comments. If you poke at a sleeping dragon, nobody will listen to you cry about getting burned.
You got your help without a single smart arse post, no need to ask for negative attention.
BTW, my horse isn't too high for me to climb down off it from time to time....
Click to expand...
Click to collapse
pardon me.. but isn't what I said the truth?
mikey411 said:
pardon me.. but isn't what I said the truth?
Click to expand...
Click to collapse
The truth is subjective and colored by each observer's point of view.
I made a valid point and I would suggest you remember it. We are working to get these issues under control and the last thing we need is someone instigating. I will beat down any post that looks to start flaming, either by attacking or inviting attack.
Now, let me put down my moderating staff and finish my sandwich.
kyphur said:
The truth is subjective and colored by each observer's point of view.
I made a valid point and I would suggest you remember it. We are working to get these issues under control and the last thing we need is someone instigating. I will beat down any post that looks to start flaming, either by attacking or inviting attack.
Now, let me put down my moderating staff and finish my sandwich.
Click to expand...
Click to collapse
point taken..
I cannot get this to work. I keep getting error 264. Does that mean I am screwed? I can access the bootloader so I am think there is still hope for me.

[Help]Unlocking Cingular 8125

Hey im new to these forums and just need help unlocking my Cingualr 8125 or put a different Rom liek the xda windows mobile 6.0. Im folowing the steps but like when i open "ROMupdateutility.exe" I follow the steps and when it starts my 8125 goes to like bootmode? It has 3 colors on the screen
red greedn and blue and then on the ROMUPDate utlity i got error 300...i tryed like so many times i need help thnx =[
EDIT : the error says error 300 invalid update tool.... "This error message will appear when you use the incorrect RUU to upgrade. Please make sure you use the correct RUU version to upgrade." where do i get the correct RUU then?...
Also found out that its a G4 because of the Ip number or w/e because it has 3 zeros then a 1 for example .0001
[Help] Unlocking Cingular 8125
Hey im new to these forums and i need help unlocking my Cingular 8125
From what ive seen on these forums my phone is G4 Because it has xxx1 at the end of the ip or w/e that **** is. I would gladly appreciate it if someone would help me unlock my G4.One of my friends has his unlocked it looks like Vista and it has all these sweet programs. Since i just got mine its g4 I guess..and since he got him like 2 months bevfore me maybe his was g3 so it was easy...
This is probably why so many people flame noobs. cause of questions like this. If you have any sort of I.Q in you you would have checked this link out http://forum.xda-developers.com/showthread.php?t=293480 its the very first post. good luck
deviusdragger said:
This is probably why so many people flame noobs. cause of questions like this. If you have any sort of I.Q in you you would have checked this link out http://forum.xda-developers.com/showthread.php?t=293480 its the very first post. good luck
Click to expand...
Click to collapse
Noob, i already checked that one. Its stickied why wouldnt i not check it before posting this thread?
The link's on that Thread are dead. They dont work anymore ***. Lol
Can't we all just get along? Let's keep things nice-nice, okay?
Anyhow, chaos36 it's really important to read up on this site before posting. All the answers are readily available (with some time and patience).
Here's a quick guideline ...
1. Your first stop should be here (the wiki)
All the information and links to get the most out of your device
2. How to SIM unlock your phone, look here.
3. How to flash any ROM other than your carrier's, here
4. Enjoy!
But just a bit of friendly advice for you in the future. Read and search all you can, then if you can't find what you're looking for, read and search some more before posting.
This site is a great place for developers, hobbyists, and enthusiasts. It's not a "helpdesk". But as long as you help yourself first, you'll find a lot of great (nice) people that will help you along your way.
Good luck and have fun!
http://forum.xda-developers.com/showthread.php?t=293480
Thnx..i ****ed up when i turn on my 8125 it stays at cingular raising the bar witht he ipl and spl number -.- please hel and ty.
chaos36 said:
Thnx..i ****ed up when i turn on my 8125 it stays at cingular raising the bar witht he ipl and spl number -.- please hel and ty.
Click to expand...
Click to collapse
Can you still get into the bootloader screen? (the red/blue/green screen)
To get into the bootloader you need to HOLD the camera button and tap the reset button.
Yes im in that screen right now if you mean the screen thtat has 3 stips a red then green then blue?
Now what do i do when im there?
chaos36 said:
Yes im in that screen right now if you mean the screen thtat has 3 stips a red then green then blue
Click to expand...
Click to collapse
Alright, this is a good example (one that we've all seen over and over again here) of how not to jump into flashing your phone without reading everything thoroughly.
Stay in the bootloader screen, keep your USB cord plugged in and reflash your original carrier's ROM. That will get you back to factory specs.
Then, don't try flashing anything else UNTIL you read everything I mentioned in the previous post first, at least a couple times through.
Just some advice
TaurusBullba said:
Alright, this is a good example (one that we've all seen over and over again here) of how not to jump into flashing your phone without reading everything thoroughly.
Stay in the bootloader screen, keep your USB cord plugged in and reflash your original carrier's ROM. That will get you back to factory specs.
Then, don't try flashing anything else UNTIL you read everything I mentioned in the previous post first, at least a couple times through.
Just some advice
Click to expand...
Click to collapse
How do i reflash the original carriers ROM?
And thank you for helping me out.
[Do you got AIM would be much easier and qicker to discuss thiss.]
chaos36 said:
How do i reflash the original carriers ROM?
And thank you for helping me out.
Click to expand...
Click to collapse
Well, glad to help. To reflash your original carriers ROM, you need to download it from their website and execute it.
Ok i got a cingular 8125. So to download it i go to Cingualr.com?...Sorry for being so noob and do you got AIm will be much easier for you to help me there ty.
I'm actually about to hit the sack. But you can get the Cingular ROM here. Just download and install it and you'll be good.
Good luck!
Wow you gave me a direct link. Thank you for all your help! Do you got AIM incase i cant figure out how to do this? maybe u can help me out tomorrow thnx for all your time and help.
Taurus pretty much held your hand and walked you thru it. You should be fine after this point. And if some of the links arent working, just let some of the mods now and they will take care of all that stuff. So good luck with the flashing.
deviusdragger said:
Taurus pretty much held your hand and walked you thru it. You should be fine after this point. And if some of the links arent working, just let some of the mods now and they will take care of all that stuff. So good luck with the flashing.
Click to expand...
Click to collapse
Yes he did and it was nice of him for doing that to me. My 8125 is fine now..but the link you gave me for the flash's are dead the links dont work =[

totally confused....about JUMP-SPL and HARD-SPL

I have watch videos...read instruction etc, etc, all I could on ATT Tilt/Kaiser flashing...I still don't have a clue. Do I do some type of CID unlock 1st....then is there a Jump SPL and than a Hard SPL. Is any of them two done from the boot loader screen. I can fix most electronics but I don't understand.. no you-tube video...i saw it on flashing the kaiser....sound quality bad for the hard of hearing (me).
Goto http://forum.xda-developers.com/showthread.php?t=396922
Download Jump SPL and Run it. Then the hard-spl. This will then allow you to flash the custom ROMs on your Kaiser.
Regards,
Carty..
I just went through this a few days ago trying to flash my first custom rom. I have to agree it is incredibly confusing and contradicting, which is why I'm taking the time to post this. Just read as much as you can about it and don't try to flash the rom until you understand. I am no expert on this by any means, but this is what i did on my tilt to flash HardSPL. I tried to make this as simple as possible just so you see the exact steps I went through, but i highly recommend reading the thread linked in the previous post by Carty above and the other link I'm posting at the very end.
1. download JumpSPL1.93-KAIS.exe from http://forum.xda-developers.com/showthread.php?t=354061.
2. get the hardSPL version you need for your rom. I used v3.56 from the link Carty gave you in the post above, because the rom I am using was based on the official att 6.1 rom. You may need a different one for the rom you want to flash I don't know too much about this yet. Leave the folder where you unzipped the hardspl files open on your desktop so you wont have to look for it later.
3. connect your phone to the PC, and transfer JumpSPL1.93-KAIS.exe over to your phone with activesync. Remove your microsd card if you have one on your phone (very important).
4.run JumpSPL1.93-KAIS.exe on your phone, it should go to a bootloader mode with the tricolor screen and underneath it will say USB.
5.Unplug the phone from the PC, wait about 5-10 seconds and plug it back in. Activesync should NOT be able to recognize your phone. If it does, something went wrong so start over.
6. Finally you can run the KaiserCustomRUU.exe from the hardSPL folder on your pc desktop and follow the instructions. It will load the HardSPL on your phone.
7. if you want to make sure it loaded, shut down your device and when your are turning it on press both the power and camera button at the same time, it will go into bootloader mode and show you what SPL is on your device. mine says SPL-3.56.Hard after I loaded the hardspl. You are now ready to flash a new rom.
This wiki helped me the most:
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
Read as much of it as you can, especially the "SPL questions?" link, that was the most useful for me.
I hope this helps
All good advice! I just loaded the HardSPL on my phone for the first time and it worked perfectly.
Now all i need is a work connection that doesnt block my attempts to download ROM's!!!!!!
tricky_uk said:
All good advice! I just loaded the HardSPL on my phone for the first time and it worked perfectly.
Now all i need is a work connection that doesnt block my attempts to download ROM's!!!!!!
Click to expand...
Click to collapse
LOL.
hjlow makes mirrors of the ROM downloads at Blogspot. Are those any good for you?
Ta
Dave
DaveShaw said:
LOL.
hjlow makes mirrors of the ROM downloads at Blogspot. Are those any good for you?
Ta
Dave
Click to expand...
Click to collapse
Sadly blogspot gets locked as well.......i've managed to download some stuff of here but in general sites it classes as 'personal storage' it gets a bit upset about...
if anyone knows any other way round i'd be eternally grateful!
ben_zin said:
I just went through this a few days ago trying to flash my first custom rom. I have to agree it is incredibly confusing and contradicting, which is why I'm taking the time to post this. Just read as much as you can about it and don't try to flash the rom until you understand. I am no expert on this by any means, but this is what i did on my tilt to flash HardSPL. I tried to make this as simple as possible just so you see the exact steps I went through, but i highly recommend reading the thread linked in the previous post by Carty above and the other link I'm posting at the very end.
Click to expand...
Click to collapse
Amen to that.. I like this guy.
Thx...clear and direct....now I am ready.
Carty said:
Goto http://forum.xda-developers.com/showthread.php?t=396922
Download Jump SPL and Run it. Then the hard-spl. This will then allow you to flash the custom ROMs on your Kaiser.
Regards,
Carty..
Click to expand...
Click to collapse
does this work on diamond?or i mean, should i frist jump spl ant hen hard, or just jump spl?
http://forum.xda-developers.com/showthread.php?t=408109&page=506 post 5055
materijalmen said:
does this work on diamond?or i mean, should i frist jump spl ant hen hard, or just jump spl?
http://forum.xda-developers.com/showthread.php?t=408109&page=506 post 5055
Click to expand...
Click to collapse
This will then allow you to flash the custom ROMs on your Kaiser.
Click to expand...
Click to collapse
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
denco7 said:
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
Click to expand...
Click to collapse
i have tried this already
http://forum.xda-developers.com/showthread.php?t=408621 but nothing has changed...i asked for help, but nobody answers....see the last posts int that thread.
materijalmen said:
i have tried this already
http://forum.xda-developers.com/showthread.php?t=408621 but nothing has changed...i asked for help, but nobody answers....see the last posts int that thread.
Click to expand...
Click to collapse
Unfortunately this is the Kaiser forum and you will get even less help here.
Post your questions in the Diamond forum and people will help,when and if they are able. And in the meantime, read and search and try to figure it out for yourself, All the steps and instructions are there.
Sometimes people, unfortunately, mistake this site for the HTC free support line, with 12 techs waiting at their PC's to help. Then they get irritated that no one answers their requests for help on a timely basis . If people won't or can't answer your questions then you need to figure it out on your own.
The bottom line is, if you don't know what you are doing, then you shouldn't be messing around with your phone. Sorry
denco7 said:
Unfortunately this is the Kaiser forum and you will get even less help here.
Post your questions in the Diamond forum and people will help,when and if they are able. And in the meantime, read and search and try to figure it out for yourself, All the steps and instructions are there.
Sometimes people, unfortunately, mistake this site for the HTC free support line, with 12 techs waiting at their PC's to help. Then they get irritated that no one answers their requests for help on a timely basis . If people won't or can't answer your questions then you need to figure it out on your own.
The bottom line is, if you don't know what you are doing, then you shouldn't be messing around with your phone. Sorry
Click to expand...
Click to collapse
I second Denco Read Read Read Read Read........ as anything you will ask, or can even think to ask..... more than likely has ALREADY been asked AND Answered.
Htc XDA member: how can I help you today?
Xda Newb: My phone isnt working.... Can you fix it ?
Htc XDA member: is your phone plugged in and turned on?"
Xda Newb:Wheres the on button?
( 1 min later) where do I plug it in at ?
(2 mins later) whats a battery?
(2.25 mins later) how do I know its on?
(2.3 mins later) why wont you answer me ?
(2.35mins later)Why arent you telling me my answers?
(2.4 mins later)whats wrong with my phone?
(2.5 mins later) You guys must be jerks because you wont spoon feed me [email protected]@@!!!
XDA MODERATOR : you noob you are banned for not reading PAGE 1 of the GODDAMN WIKI as all your answers were right there 1 click away. Now you cant access them HAHA. This is what you get for being IMPATIENT AND ANNOYING ( They should really do this here )
LOL
Just my rant
denco7 said:
No , this is what works on the Diamond
http://forum.xda-developers.com/showthread.php?t=414835
Click to expand...
Click to collapse
How is this link related to the topic?
I want to use JumpSPL to change the version of HardSPL I have on diamond b/c my USB port does not work.
kyniemxotxa98 said:
How is this link related to the topic?
I want to use JumpSPL to change the version of HardSPL I have on diamond b/c my USB port does not work.
Click to expand...
Click to collapse
And what I said was that this was the Kaiser forums and not the Diamond forums. Putting Kaiser Spl's on a Diamond will brick your phone faster than throwing it into a bucket of water. So I gave him a link to the Diamond forum and Diamond Security/CID/Sim unlocker.
How is your question related to the Kaiser forums ?
Will it work on my TP/Excalibur? No as phones have different hardware to which is why h-spl's are device specific.
The best way to help yourself and not get a brick "expensive paperweight" is to head to device subforum and do some reading, as last thing you want is to be creating a thread named "Help"
denco7 said:
And what I said was that this was the Kaiser forums and not the Diamond forums. Putting Kaiser Spl's on a Diamond will brick your phone faster than throwing it into a bucket of water. So I gave him a link to the Diamond forum and Diamond Security/CID/Sim unlocker.
How is your question related to the Kaiser forums ?
Click to expand...
Click to collapse
Since I cannot find anything helpful in Diamond forum, I dig around in other forums to try to rescue my phone and make it usable.
Which is a recipe for diasaster...seriously, if you are gonna do something as stupid as to try to make something SPECIFICALLY for another device work on yours, then you do not deserve to own a Diamond.

restoring a bricked phone

any ideas.......read all the threads here, nothing works.
i had the 1.7 orange version. hardspl'd it and put a 6.5 dev on there, but radio quality was poor. so followed the procedure to put the stockspl back on there. But nothing else works, I can't restore the original rom (grabbed from here) as the screen stays at 0%. tried to hardspl it again but that doesn't work either.
what do i do now .........?
thanks.
Was restoring the stockspl succesfull?
What info do you get in bootloader?
The info is:
JADE110 64M
SPL-1.40.0000
MicroP-Jade (LED) v5
It still has windows 6.5 rom on there tho, which is seriously messed up now.
pls dont wast threads
hi
a humble request Kindly dont was threads i have created a specific thread for Q& A on Jade why not post it their pls see below link
i see u have wasted 3 thread which could have been used for a much more usefull purpose this is just my humble request to you i hope u will do the neeful thanks
Note : kindly read the first page u would understand why not to waste threads
http://forum.xda-developers.com/showthread.php?t=534581
orange3g said:
any ideas.......read all the threads here, nothing works.
i had the 1.7 orange version. hardspl'd it and put a 6.5 dev on there, but radio quality was poor. so followed the procedure to put the stockspl back on there. But nothing else works, I can't restore the original rom (grabbed from here) as the screen stays at 0%. tried to hardspl it again but that doesn't work either.
what do i do now .........?
thanks.
Click to expand...
Click to collapse
"a humble request Kindly dont was threads" read your thread on that, space taken up whether new thread or reply is the same.
orange3g said:
The info is:
JADE110 64M
SPL-1.40.0000
MicroP-Jade (LED) v5
It still has windows 6.5 rom on there tho, which is seriously messed up now.
Click to expand...
Click to collapse
Am afraid you have a problem, you should have down it the other way around...first stock ROM then stock SPL.....but this is merely a fact then helping you out, i have absolutely no clue how to go from here...sorry!
Maybe someone who can offer some practical assistance will be along soon ......
@Nirak: yes, I misread it. What a silly thing to do. Do you think HTC can help. The phone is in warranty.
Well, since you've got stock SPL on it you could give it a try. When they start asking questions you could say you tried to install a WM 6.5 ROM by accident.., dunno if they buy it...
But on the other hand, being honest is maybe better, they might just help you out or else you have to pay, but since you have a rather expensive paperweight right now, this might be an option too.
BTW.. did you try to contact one of the releasers of the HardSPL? (Cmonex or Olipro), you never know where they can come up with....
May be they will see this thread. .... otherwise how can I contact them?
Thanks for the ideas.
Have you tried to flash your rom through the boot loader mode
try this
hi
try this
1. do HSPL on ur phone again using the tools given in the thread
2.after successful HSPL Flash the Stoc rom the right one for ur phone
3.then flash the Stock SPL again the right spl for ur phone
this is just my suggestion i hope ur successful and it helps to solve ur problem
goodluck
orange3g said:
May be they will see this thread. .... otherwise how can I contact them?
Thanks for the ideas.
Click to expand...
Click to collapse
Send them a PM, Olipro is not often here, but Cmonex is
haree said:
hi
try this
1. do HSPL on ur phone again using the tools given in the thread
2.after successful HSPL Flash the Stoc rom the right one for ur phone
3.then flash the Stock SPL again the right spl for ur phone
this is just my suggestion i hope ur successful and it helps to solve ur problem
goodluck
Click to expand...
Click to collapse
Doesn't work because it needs a functioning windows mobile, which I don't have. Mine gets stuck.
thomas01_58 said:
Have you tried to flash your rom through the boot loader mode
Click to expand...
Click to collapse
Yes, nothing happens. The screen is stuck at 0%. I tried using a htc original rom, it got to 1% and said something like not suitable for this device.
I sure this sounds rather silly ,and I am sure you have tried it,have you tried removing the battery and then putting it back again.
Not sure if you tried this already:
Run HardSPL when your phone is in tricolor mode (bootloader?).
Then reflash a stock ROM, also in tricolor mode.
Finally, flash stock SPL.
Hope this helps.
@izzysc: I have tried it (will try again though) in running HardSPL when phone is in tricolor mode. It did not work.
Nirak said:
Well, since you've got stock SPL on it you could give it a try. When they start asking questions you could say you tried to install a WM 6.5 ROM by accident.., dunno if they buy it...
But on the other hand, being honest is maybe better, they might just help you out or else you have to pay, but since you have a rather expensive paperweight right now, this might be an option too.
BTW.. did you try to contact one of the releasers of the HardSPL? (Cmonex or Olipro), you never know where they can come up with....
Click to expand...
Click to collapse
I have PMd Cmonex. Thanks.
replied to PM
cmonex said:
replied to PM
Click to expand...
Click to collapse
Tx! had an idea you could help out...

My bootloader dosent work

the tri colour thing comes up but after that it freezes on the loading screen I am running windows mobile 6.1 (came with phone).(sony Erricson Xperia x1i
mikebuckley888 said:
the tri colour thing comes up but after that it freezes on the loading screen. any fixes would be much apperichated.
Click to expand...
Click to collapse
for starters: retry w/o sd card
and add a little more info on how your phone is setup and what you already tried or not, no thought-readers out here (that I know of)
Does it say anything in perticular when it freezes? If you'd manage to by accident fail to flash a rom you might have this issue saying something about updating rom.
My refrigerator also doesn't work...
no serious dude, first read before posting.
And if you don't get out, give us so much info so that we could help you.
Good luck
maddude88 said:
Does it say anything in perticular when it freezes? If you'd manage to by accident fail to flash a rom you might have this issue saying something about updating rom.
Click to expand...
Click to collapse
Yep it has the loading screen with three dots.
(thanks veryone for you help)
have you hard-spl'd?
or is this what your trying to do?
yeah thats what i'm trying to do
Jonny4911 said:
have you hard-spl'd?
or is this what your trying to do?
Click to expand...
Click to collapse
yeah i'm trying to do that.

Categories

Resources