I did upgrade today to AKU 3.3 Crossbow from 2.3 and all went OK but then I restored my backup made with SPB Backup, restore took longer as usual and then after reboot stays in boot screen where the IPL/SPL/GSM and OS numbers are.
Battery in out did not help.
Now how can I flash again?
Thx in advance.
Ok i solved my own problem, not even romupdate_115.exe helped.
What I did:
1. got to bootloader mode (camere button + power on)
2. connect USB
3. start AKU 3.3 Crossbow again
And now main XDA mini S is alive again.
Related
Just trying to update my IIs to the lastest ROM. I did backup to SD before update. During updating the process seem very fast for me. Then after update finish my IIs still stuck in BOOTLOADER screen... soft&hard reset cannot help. So, I decide to restore with the backup file in SD. I insert my SD and press Power+Notes+Reset to enter BOOTLOADER again... After waiting for a while... screen show 'Not Allow Update'
Now, I can't update and I can't restore to previous rOM.
How can I do?
take out the battery, put it back in and run the update again.
Now I did understand that you are using a 02 rom on a o2 devce and that this device is a xdaIIs, and that you are using the ship.exe file as is.
>take out the battery, put it back in and run the update again.
Already done but didn't work still stuck in bootloader screen.
> Now I did understand that you are using a 02 rom on a o2 devce
> and that this device is a xdaIIs, and that you are using the
> ship.exe file as is.
That's correct.
Well you will have to drain the backup battery.
Take the battery out, lock the battery lock in the closed postion run off the backup battery.
There was some key combination that got you in and out of bootloader I am not sure if it was the same as the one you mentioned in your first post.
> Well you will have to drain the backup battery.
> Take the battery out, lock the battery lock in the closed postion
> run off the backup battery.
I did seperate body and battery for more than 5 hrs. After put it back and turn on, the BOOTLOADER appear again.
> There was some key combination that got you in and out of bootloader
> I am not sure if it was the same as the one you mentioned in your first post.
The keys should be the same.
Any suggestions?
Sorry no more,
(You sure you drained the backup with the bartery lock in the locked postion?)
Thank you very much for your help.
omg wtf do i do now?! my pc rebooted 31% into the flash.. it blue screened out of no where!
now its stuck on a IPL 2.21 screen!
this happened to me a few times as well. I just re-tried the flash from another machine and it worked fine.
but i cant establish a active-sync connection because the phone wont start it just stays at the 2.21 screen thats red/green/blue/white! omg im about to cry what do i do lol
I have seen the same screen, and have also had the computer blue screen on me probably 3 or 4 times now. When i plugged it into another machine with activesync, i ran the updater and it worked fine.
im trying it right now on 2nd pc still downloading the rom file tho
ok i was able to flash using another computer thank god!
:lol:
Can you post the steps of reflashing the wizard? I've tried a flash on another system, but it still doesn't work...
My steps:
1. Install Active Sync 4.1
2. Connect the wizard on usb
I've tried to downgrade the wizard with wizbackup. wizbackup need to flash IPL/SPL 1.01. The flash was ended without errors. But now the wizard starts and I only see the three colors and the version of IPL/SPL. Then I connect the wizard, Active Sync doesn't get a connection to the phone.
UPDATE:
In another thread I read that the wizard can't be flashed in IPL/SPL 1.01 without an OS. Can anyone verify this information or help me?
UPDATE II:
I finaly found out, that the phone can be restored with an image from the sd-card.
1. Put an image from the system to sd-card with psdwrite.exe
2. Power Off the phone and put in the sd-card
3. Power on the phone holding the camera key
4. Then the bootloader is coming up, press the voice key during 3s
5. The bootloader upgrades your phone from sd-card
Good luck!
that **** happens to me all the time, it always crashes to the boot loader and once its there you can just restart the upgrade no problem. if you need to boot into the boot loader then simply, from a turned off state, hit the wifi button, voice command button and power button, then release the power only and it will boot into the tri colored boot loader. then reinstall your image and soon you will be kickin it with your **** in it once again! booyakasha!
actually now that i think about it that will just go to the hard reset screen. you really just want to stick the stylus in the reset hole if you need to get to boot loader i think. i dont remember off hand.. just mess with it. if you break it just say you got it that way and exchange that ****
I installed the HTC Kaiser DLL replacement installer and then restarted my device. Now when it boots it won't go past the my info (owner info) screen. If I try to do anything at that screen whole device goes black and frozen I have to reset again. Anyone having this similar problem or know how I can fix it? I would really appreciate the help!
I was running WMobile 6.1 with the RUU_Kaiser_HTC_WWE_3.03.405.0_radio_sign_25.70.40.02_1.64.06.04 ROM
Once or twice somehow it got to the unlock screen but I can't get back there now I don't know how it got there the first times either just reset after reset.
Thanks
I was able to enter bootloader and reflash the rom. Held down camera button and used the stylus to push the little reset button next to usb port. Then ran rom updater as normal
I tried to flash my Qtek 9100 to WM6 using the flashing tutorial on this site.
I followed the steps in the tutorial. I downgraded to Buttons ROM, unlocked the CID, and then I flashed the 3.08 IPL/SPL in stead of the T-Mobile 2.26.
Then I tried to use farias kitchen to make a WM6 and flashed it to the phone.
Everything seemed to go smoothly, but when I tried to start the phone after flashing the 3.08 and farias' to the phone, the phone just hangs at the startup screen with the picture of the beer glass and the coloseum.
I've tried to downgrade to Buttons firmware and I've also tried the Xda_MiniS_LaunchROM, but it doesn't help. I'm still stuck at the welcome screen.
Is there anything I can do, or have I bricked my phone for good?
flash an original qtek rom to your phone then try to flash the rom again
Your phone isnt bricked (yet)
I've done that, but it doesn't help. Still just hangs at the SPL/IPL screen.
Solution (worked for me)
I found a solution while looking trough the forum
I was facing the same problem on a G3 phone
this is copied from that link except the link to MTTY.exe is different (previous one doesn't work
See (http://forum.xda-developers.com/showthread.php?t=307332)
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY.exe ( http://forum.xda-developers.com/showthread.php?t=231190 ). After open, on Port selection, choose USB and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
I hope this helps you out
It worked for me (and other people if you look at the forums)
That solution was already known and was, in fact, discovered for the Wizard by a guy called 'Drugstore'
But what really matters is that this procedure only works if the device is already CID unlocked.
cheers
MDA Vario freezes at 2nd boot screen
I have the same problem. I flashed wm6.1 according to tutorial on this side. everything worked fine, until the time I uninstalled some application. after that my Vario froze. after soft reset it stopped on second screen (the one with info), and so it is anytime I try to reflash to other ROM. everything works fine until the time it shoud reboot.
I found this thread and tried the thing with backup image. everything worked, copying image to the phone ended with success. so I turned off the phone and started it again. but now, after all, I'm just back at the beginning
can somebody help me out with another solution??? pls.....
Try mtty
grinmustaine said:
I have the same problem. I flashed wm6.1 according to tutorial on this side. everything worked fine, until the time I uninstalled some application. after that my Vario froze. after soft reset it stopped on second screen (the one with info), and so it is anytime I try to reflash to other ROM. everything works fine until the time it shoud reboot.
I found this thread and tried the thing with backup image. everything worked, copying image to the phone ended with success. so I turned off the phone and started it again. but now, after all, I'm just back at the beginning
can somebody help me out with another solution??? pls.....
Click to expand...
Click to collapse
maybe trying mtty
task 28
task 28 55aa
then upgrade again
this is not the steps as is... so search the way
+ Que PPC said:
maybe trying mtty
task 28
task 28 55aa
then upgrade again
this is not the steps as is... so search the way
Click to expand...
Click to collapse
I didn't have chance to try this.... My Vario is already dead... Probably is my fault... As far, I wasn't able to flash to official T-mobile ROM, I did a backup copy to a SD card on my friends phone, and then tried to copy the image into mine... I'm afraid I destoyed bootloader this way After I turned off my phone first time after flashing, it didn't start again.... It doesn't react even to wall charger... Nothing... Just dead Vario
Get a powerfull charger
grinmustaine said:
I didn't have chance to try this.... My Vario is already dead... Probably is my fault... As far, I wasn't able to flash to official T-mobile ROM, I did a backup copy to a SD card on my friends phone, and then tried to copy the image into mine... I'm afraid I destoyed bootloader this way After I turned off my phone first time after flashing, it didn't start again.... It doesn't react even to wall charger... Nothing... Just dead Vario
Click to expand...
Click to collapse
There is a post that suggest that somebody revives his batt with a wall charger, maybe is your batt... is dead... or your s is bricked.
Hi!
My Display died, I have flashed with my stock rom (win mobile) but I still need to install stock SPL. I Still run Hard SPL and I do not want warranty issues.
After I flashed with my win mobile (backup original rom) it boots into screen calibration, which ofcourse I cannot see and finnish. I have tried clicking all sorfs of buttons. I have tried running the my mobiler remote desktop win mobile stuff, but it can't start up as the phone still is in calibration/initial setup/config mode.
Any suggestions on how I skip the initial setup dialogs ? Or any other suggestions on how I get install of Stock SPL / Uninstall my Hard SPL when I have dead display and is stuck in screen calibration mode when booting?
Sure appreciate it! Thanks!
i'm pretty sure you can just boot into bootloader and flash stock spl that way.
you just can't do it the other way round.