hey guys,
need some help from the xpert here, my tilt cannot boot up its stuck on the AT&T screen, i have tried soft reset, hard reset and still cannot fix the problem. the worst problem is cannot sync into my pc...
thx
you sure you attempted to hard reset and still nothing?
take out your memory card and see if that does anything.
If it still won't boot up, then get into bootloader mode and re-flash your rom.
We need a bit more info to help:
1. Did you have HardSPL installed? Check by looking at the tri-colour bootloader screen (press and hold power/camera buttons and reset with stylus at the same time).
2. What ROM/radio do you have?
3. Did you try to flash another rom or radio before this problem hapenned?
4. When you hard reset, did you get the grey screen with instructions telling you to send to continue? Sometimes the hard reset routine doesn't always work properly.
5. Are you running XP or Vista on your PC?
Try going into the bootloader and connecting the USB cable. The screen text at the bottom should change from 'Serial' to 'USB'. If you have Hard-SPL you should be able to re-flash any rom (some here) - but check for compatible radios. If you don't have hard-spl try flashing the manufacturers original rom.
Hello.
I'm opening this thread because my Diamond seems to be diying and I wanted to know if someone got an idea.
Yesterday, my phone suddendly rebooted without warning after a month.
I thought It was nothing, but the phone started to reboot allthe time. The phone boot, show my operator logo (befor the winmo loading screen), and then reboot again, again and again.
I decided to do a little Mtty maintenance and reflash (from internal memory). The phone reworked for a couple of hours and restarted to do a reboot loop. I thought the rom I was using was in fault.
Re Mtty maintenant and flashing the phone with mu Prange stock rom. Several hours léter, the phone restarted to boot.
So where I am ?
If I let the phone off (like a night), he will launch windows and will works between a couple of minutes from a couple of hours befoor rebooting. If I put the phone in bootloader mode It won't reboot and will wait with his beautiful rainbow screen. But if I leav the bootloader mode, reboot over reboot, yay !
When the phonedecide to boot completly,it's a regular soft reset, not a hard reset.
Did anyone here have an idea ? Thanks !
How often did you flash since you have your diamond ?
Try to reflash a radio. Maybe your flash memory is dead =/
It sounds like the rom image might be corrupted - I had this problem with a 28003 rom I tried in which the phone would take a hard reset - boot fine - reset and reload fine... and then whenever you tried to restart it after that it went into a boot loop that eventually came up with a screen saying "the phone cannot boot because of uncertified software or incorrect shutdown procedure"
I solved it by putting the phone into bootloader (switch on holding both power key and volume down key) - connecting it to my computer and reflashing it. It DOES NOT need a activesync connection in this mode but you do need the Hard-SPL on the phone (im running olinex 1.40)
hope that helps
Jemma
Thx JoOos and Jemmauk.
But I already tried to reflash the Radio and the rom Image.
I Tried 3 different Rom images.
One orange official , aztor re-evo and an another one.
But the phone don't display any errors. It will just never stop to reboot without saying a thing.
Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
Hello everybody,
I have a bad problem with my diamond, yesterday I tried to update my Gen.Y 5.3 ROM with Memo 2.5.1.0 ROM.
After flashing, my diamond will restart, as always, but the first time it makes an error with trying install something like "windowslive.update".
After this error my device was blocked.
I had remove the battery and restart it, nothing to do, it remaing blocked into first black screen so you see the ROM version.
So I have make hard and soft reset but nothing.
So I have launched bootloader with volDown+Reset and reflash Diamond with Gen.Y 5.5, now my device starts (not always) but after a little second it blocked again.
I need to remove the battery, but always the ROM reinstall himself with reset of contacts,SMS and recalibrate e reinstall all programs...
anybody have any idea what can I do?