Hello.
I'm opening this thread because my Diamond seems to be diying and I wanted to know if someone got an idea.
Yesterday, my phone suddendly rebooted without warning after a month.
I thought It was nothing, but the phone started to reboot allthe time. The phone boot, show my operator logo (befor the winmo loading screen), and then reboot again, again and again.
I decided to do a little Mtty maintenance and reflash (from internal memory). The phone reworked for a couple of hours and restarted to do a reboot loop. I thought the rom I was using was in fault.
Re Mtty maintenant and flashing the phone with mu Prange stock rom. Several hours léter, the phone restarted to boot.
So where I am ?
If I let the phone off (like a night), he will launch windows and will works between a couple of minutes from a couple of hours befoor rebooting. If I put the phone in bootloader mode It won't reboot and will wait with his beautiful rainbow screen. But if I leav the bootloader mode, reboot over reboot, yay !
When the phonedecide to boot completly,it's a regular soft reset, not a hard reset.
Did anyone here have an idea ? Thanks !
How often did you flash since you have your diamond ?
Try to reflash a radio. Maybe your flash memory is dead =/
It sounds like the rom image might be corrupted - I had this problem with a 28003 rom I tried in which the phone would take a hard reset - boot fine - reset and reload fine... and then whenever you tried to restart it after that it went into a boot loop that eventually came up with a screen saying "the phone cannot boot because of uncertified software or incorrect shutdown procedure"
I solved it by putting the phone into bootloader (switch on holding both power key and volume down key) - connecting it to my computer and reflashing it. It DOES NOT need a activesync connection in this mode but you do need the Hard-SPL on the phone (im running olinex 1.40)
hope that helps
Jemma
Thx JoOos and Jemmauk.
But I already tried to reflash the Radio and the rom Image.
I Tried 3 different Rom images.
One orange official , aztor re-evo and an another one.
But the phone don't display any errors. It will just never stop to reboot without saying a thing.
Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.
Related
omg wtf do i do now?! my pc rebooted 31% into the flash.. it blue screened out of no where!
now its stuck on a IPL 2.21 screen!
this happened to me a few times as well. I just re-tried the flash from another machine and it worked fine.
but i cant establish a active-sync connection because the phone wont start it just stays at the 2.21 screen thats red/green/blue/white! omg im about to cry what do i do lol
I have seen the same screen, and have also had the computer blue screen on me probably 3 or 4 times now. When i plugged it into another machine with activesync, i ran the updater and it worked fine.
im trying it right now on 2nd pc still downloading the rom file tho
ok i was able to flash using another computer thank god!
:lol:
Can you post the steps of reflashing the wizard? I've tried a flash on another system, but it still doesn't work...
My steps:
1. Install Active Sync 4.1
2. Connect the wizard on usb
I've tried to downgrade the wizard with wizbackup. wizbackup need to flash IPL/SPL 1.01. The flash was ended without errors. But now the wizard starts and I only see the three colors and the version of IPL/SPL. Then I connect the wizard, Active Sync doesn't get a connection to the phone.
UPDATE:
In another thread I read that the wizard can't be flashed in IPL/SPL 1.01 without an OS. Can anyone verify this information or help me?
UPDATE II:
I finaly found out, that the phone can be restored with an image from the sd-card.
1. Put an image from the system to sd-card with psdwrite.exe
2. Power Off the phone and put in the sd-card
3. Power on the phone holding the camera key
4. Then the bootloader is coming up, press the voice key during 3s
5. The bootloader upgrades your phone from sd-card
Good luck!
that **** happens to me all the time, it always crashes to the boot loader and once its there you can just restart the upgrade no problem. if you need to boot into the boot loader then simply, from a turned off state, hit the wifi button, voice command button and power button, then release the power only and it will boot into the tri colored boot loader. then reinstall your image and soon you will be kickin it with your **** in it once again! booyakasha!
actually now that i think about it that will just go to the hard reset screen. you really just want to stick the stylus in the reset hole if you need to get to boot loader i think. i dont remember off hand.. just mess with it. if you break it just say you got it that way and exchange that ****
Hy guys, after some month with my diamond and (hundred of rom changed), yesterday my phone started to reset every few seconds without possibility to start windows ...
it's seems that or soft rest button is dmaged or something with battery fault. I've tried two different battery but no way.
I've tried to flash a standard rom but after upgrade there's error an no way to finish process.
Now it' s difficult also have a soft reset because when i push red button nothing happens. Sometimes without battery i'm able to go in a boot mode...but whe i put my battery phone restart as before....
So i'm desperate......
Any suggestion???
regards
You could try to format your device and then freshly flash a new ROM:
http://forum.xda-developers.com/showpost.php?p=3433851&postcount=22
AAAARRRRRg my diamond is definitly briked.. I've tried everything to solve my problem but no way. It seems that i've a power button, so every time i put battery and start phone, after a couple of seconds i've reset in loop....
No way to take in boot mode....
There's a way to recover my data in "internal storage"??
Regards
my phone is hard spled. things went fine after hard spl, i was able to flash 2 roms, the last one was juststablev2. after one day my phone started to freeze, random crashes, finishing with a "white screen" and then resets. and after a couple of crashes the phone coulnt even load windows anymore, after the splash screen it continiued to reset. and now, the phone dosnt gets on anymore, it only goes to bootloader (not when you turn on the phone, it cant be turned on, only pressing cam button and resetting turns the phone on and you can only be in bootlader. ) i tried everything, readed almost everything in xdadevelopers, tried to flash with shipped roms, tried to flash with custom roms, tried to flash from pc, to flash from sd card (and yes i know everything to do becouse i did my earlier flashed with sd card, all went without any problem). it just looks the phone is dead, but can enter into bootloader. do anyone have any idea ? ill be realy very thankfull if someone can think something about my problem.
ps : my SPL is 4.70.yang
You can't flash your carrier ROM from bootloader mode via USB?
No, i can not. i forgot to mention that every rom install attempt is turning back with the error 244 : invalid model id.. Just one time, i did get a message, when i was trying flash with the juststablev2, it gave me an error about certificate. but not the same sd card, same rom, gives me nothing, just goes to bootloader mode after checking the sd card.
same problem with me(bendede aynı sorun war osman kardes:/))
help help help
For the past few months I've been flashing separate Energy Roms onto my tilt 2. I finally found one that I liked and stuck with it for the past few weeks, which was the Dinik Glass Energy rom.
Everything was running great until last night when I was watching a video on You tube and everything froze up. I pulled the battery out and turned the phone back on and now it keeps going to the boot loader screen....
I've tried re flashing different roms to see if that would work but I've gotten nothing out of it.
If anyone could let me know of anything that i could possibly do to try and fix this I would be highly appreciative of it.
I dont know what may have caused the problem but in your situation i would have tried to do task29, flash radio and then flash a new ROM. this is normally how i flash my roms but task29 may remove somethin that may be causing the problem. if you have already done so, sorry for wasting 5 secs of your life ... let me know if it worked
Can you show me where I can dl task 29 at?
I had the same thing happen to my tilt2 last week!
Use task 29,
dont freak out when it only shows the screen that says touch pro 2.
Enter into bootloader and run ruu from there, it will fix everything.
Dont flash with sd card in or it will happen again.
I had to clear my sd card and reload it! good luck.
one more thing after task 29 do not disconnect from usb until you load next rom, that is what worked for me best.
hope it helps
I used the RUU and i tried reloading the ROM but it still starts in boot loader screen every time.
Should I just hit the hard reset?
you have nothing to loose by a hard reset at this point ... IF that works.
If I hard reset it will I have to flash a hard spl again?
Ok i noticed that yoy are pritty confused about the terminolog, so here is some help:
1. Task 29 - delets your rom of the phone so your phone become practicly unuseble.
2. HardSpl - "Unocks" (allowes) the phone for flashing custom made roms - i.e. all roms and ro preform Task 29.
3. Hard rest - reinstalls allready flashed rom.
4. Soft reset restart the phone - on/of
5. BOOTLOADER - allowes you to flash without activesync and from Sd card.
When any problem turns on with phene i usually check to see if there is any connection running. I discovered that too much internet over phone makes a phone buggy dissregarding the rom.
You dont have to hardspl phone again, once you did is enough.
Okay well here is the problem then... every time I turn the phone on it goes straight to bootloader. The only button I press to turn the phone on is the main power button. I've ran the custom RUU twice now. I've tried flashing a new rom onto the phone via sd card but it still turns on in bootloader mode. I'm nearly freaking out now because I'm led to believe I've got a bricked piece of $hit.
I hate sounding like a noob but if there is some way someone could run a step by step process to me that works I might through some $$ via pay pal.
Joe Mustard said:
Okay well here is the problem then... every time I turn the phone on it goes straight to bootloader. The only button I press to turn the phone on is the main power button. I've ran the custom RUU twice now. I've tried flashing a new rom onto the phone via sd card but it still turns on in bootloader mode. I'm nearly freaking out now because I'm led to believe I've got a bricked piece of $hit.
I hate sounding like a noob but if there is some way someone could run a step by step process to me that works I might through some $$ via pay pal.
Click to expand...
Click to collapse
I had the same problem with a phone about a month ago. I was able to flash the stock rom and it would boot up then put on the stock SPL and relock the phone. Sometimes I was able to take the battery out and get it to boot but even with the stock ROM I was getting the bootloader at startup. So once I reloaded the stock ROM and relocked it, I returned it and got a replacement.
Sorry, nothing I did every resolved the problem.
good luck.
I agree with taking everything back to stock
flash stock rom
do a spl relock
and start over...
oh, and dont forget about radios! idk if that could be part of the problem tho
I never changed the radio's so I should be good to go then, just the stock rom?
Try this :
- Enter bootloader
- Connect USB cable so "serial" in the bootloader changed to "USB"
- Perform Task29
- Reset
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader.
- Flash a stock ROM. Download it from HTC website if you don't have one.
- Reboot.
Ow, the stock ROM also contains Radio. So Flashing with stock ROM will flash your radio also.
gabmurillo said:
I had the same problem with a phone about a month ago. I was able to flash the stock rom and it would boot up then put on the stock SPL and relock the phone. Sometimes I was able to take the battery out and get it to boot but even with the stock ROM I was getting the bootloader at startup. So once I reloaded the stock ROM and relocked it, I returned it and got a replacement.
Sorry, nothing I did every resolved the problem.
good luck.
Click to expand...
Click to collapse
When you returned your phone and got a replacement was your phone starting in boot loader?
If so how did the workers at the ATT store react to that so I know what to expect?
shadixs said:
Try this :
- Enter bootloader
- Connect USB cable so "serial" in the bootloader changed to "USB"
- Perform Task29
- Reset
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader.
- Flash a stock ROM. Download it from HTC website if you don't have one.
- Reboot.
Ow, the stock ROM also contains Radio. So Flashing with stock ROM will flash your radio also.
Click to expand...
Click to collapse
How would you recommend that I flash the stock ROM back on?
I'm kind of confused because I've always flashed with my SD card, how do I do it through my USB? Could you give me a step by step?
Well, those steps I wrote are basically "step-by-step how to flash from usb".
Allow me to clear it:
- Enter bootloader -> Hold volume down button while pushing the reset switch
- Connect USB cable to your computer. and wait until the "serial" word in the bootloader changed to "USB"
- Perform Task29, download task29 and unzip it. run ROMUpdateUtility.exe. Follow the instruction.
- Reset/reboot. well, the phone will reboot itself after task29 is completed
- If the phone enters bootloader skip this step. If not, hold volume down key while resetting (push the reset switch with stylus). The phone will enter bootloader. Connect the usb cable again to your computer (if you disconnect it.) and wait until the word "serial" changed to "usb" again.
- Flash a stock ROM. Download it from HTC website if you don't have one. Just run the exe file you downloaded and follow the wizard.
- Reboot.
I reccomend you to flash with stock ROM because Stock ROMs are "Guaranteed to work(at least by HTC )" and contains radio that may be the cause of your problem. there's no need to flash to stock SPL, yet.
I was stuck in bootloader...
You can find task 29 here. I always do this before flashing.
After task 29, make sure USB is still plugged in and enter bootloader by holding Volume Down key while hitting the reset button. You should see USB on the bottom of the bootloader screen.
Now you should be able to flash the NRG ROM by running the RUU in the same folder as your ROM (rhodium.nbh file).
If this doesn't help, search the entire forum for "stuck in bootloader." I did this and it saved me the hassle of the warranty process.
Before
[/URL]
Joe Mustard said:
Can you show me where I can dl task 29 at?
Click to expand...
Click to collapse
Joe Mustard said:
When you returned your phone and got a replacement was your phone starting in boot loader?
If so how did the workers at the ATT store react to that so I know what to expect?
Click to expand...
Click to collapse
I was able to get it to boot to the ROM by removing the battery several times and reinserting, powering on until it boot. I am on TMobile and called them and they sent me a new phone and returned the old through the mail after expalining the problem. So never went into the store.
good luck.
Hi,
Today I found a problem with my phone. Firstly it hang and then after reset after a start screen it enters the data transfer/recovery mode witch looks like that
telephone -> usb cable -> laptop.
I cannot enter boot loader and also hard reset is not working.
Does anyone has any idea how to fix it?
Additional information:
week ago I have installed Deepshinging mango 7.5 with HSPL.
After connecting with zune it enters recovery mode, and if I try to proceed the arrow on the phone screen above changes direction to the opposite and it is crossed. After that there is an automatic reset of phone (it enters the same data transfer/recovery mode) and zune writes error 801812E0.
Try removing the USB cord and battery, then waiting a while (like 30 seconds). Put the batty back in, cross your fingers, and power on the phone.
My phone (retail ROM, OSPL) got stuck on that screen after I used the backup-at-any-time tool. Normal reboots just kept going back to that screen. The steps above fixed it. Hope that helps!
Nope, I have tried to:
- remove battery
- completely discharge battery
and still the same.
Hello,
If your phone is in mango you have to downgrade to nodo using the gold card.
Cheers.