Database Develop

My Trinity is dead ? need HELP from expert

RIP my toy ?
Hello All,
Since yesterday , my device always display during boot boot: Press SEND to restore factory default, press END to quit
I all tested:
enter in bootloader mode : color screen display during 0.5 sec before come back to "Press SEND....
perform hard reset : same as above
soft reset : same as above
if i choose SEND or END it's same , my device come back always finally to Press SEND ...
is there any hope ? last trick to try ?
Thanks
EDIT : after remove and put in my batterie a lot of times (more than 20 times) , my device lived again and boot properly
i flash for a more recent ROM , i will see
the old one was the first go out under WM 6.5 (several weeks)
exté
EDIT : 12 oct: once again i have this message at each boot "Press SEND to restore factory default ..." UNABLE to bypass ... please help , i find no solution on google and i refuse to think i am the only to have this issue ...

Hi,
I have ~ the same problem.
After an upgrade, my trinity did not reboot.
I tested : soft reset, hard reset...
My device did not boot
After reading your post, I removed the battery during + 20 minutes then tried to reboot. Result : no change
Do you have any idea to resolve my problem ?
Thanks,
Kabylus

kabylus said:
Hi,
I have ~ the same problem.
After an upgrade, my trinity did not reboot.
I tested : soft reset, hard reset...
My device did not boot
After reading your post, I removed the battery during + 20 minutes then tried to reboot. Result : no change
Do you have any idea to resolve my problem ?
Thanks,
Kabylus
Click to expand...
Click to collapse
I saw this solution bellow from this forum
23rd June 2009, 10:07 AM
albgen
Junior Member Join Date: Aug 2007
Posts: 13
--------------------------------------------------------------------------------
if your htc hangs like mine(blakc screen and nothing else) you have to load the boot loader.
To load the boot laoder press power+camera+softreset. You will see on the screen some colors. Then plug your usb cable and refalsh.
ps:soft reset is the button over the call button
Posted by albgen (Junior Member)
Hope this helps

I had the same problem when I did the upgrade to wm6.5.
however, dispite the facts that your phone already dead, no harm trying the same method again.
1) remove the battery.
2) press any buttons, the best one to choose, on off button. (Reason, all phone has backup battery, you got to drain it completely before the memory is fully wipe off)
3) Best is, leave the phone without batt for a day or weeks and let the backup batt drain up.
4) pull the batt back, press the right & left soft button & the reset button (HARD RESET).
It works for me...
Good Luck to you guys!

mischunt said:
I had the same problem when I did the upgrade to wm6.5.
however, dispite the facts that your phone already dead, no harm trying the
Click to expand...
Click to collapse
Hi Mischunt,
which kind of issue you have ?
trinity which refuse to boot or same screen as me "press send to restore ...." because this issue came from to time (when the battery is empty i believe) and now impossible to my device to boot again

[BUG]Infinite Reboot

Hello.
I'm opening this thread because my Diamond seems to be diying and I wanted to know if someone got an idea.
Yesterday, my phone suddendly rebooted without warning after a month.
I thought It was nothing, but the phone started to reboot allthe time. The phone boot, show my operator logo (befor the winmo loading screen), and then reboot again, again and again.
I decided to do a little Mtty maintenance and reflash (from internal memory). The phone reworked for a couple of hours and restarted to do a reboot loop. I thought the rom I was using was in fault.
Re Mtty maintenant and flashing the phone with mu Prange stock rom. Several hours léter, the phone restarted to boot.
So where I am ?
If I let the phone off (like a night), he will launch windows and will works between a couple of minutes from a couple of hours befoor rebooting. If I put the phone in bootloader mode It won't reboot and will wait with his beautiful rainbow screen. But if I leav the bootloader mode, reboot over reboot, yay !
When the phonedecide to boot completly,it's a regular soft reset, not a hard reset.
Did anyone here have an idea ? Thanks !

How often did you flash since you have your diamond ?
Try to reflash a radio. Maybe your flash memory is dead =/

It sounds like the rom image might be corrupted - I had this problem with a 28003 rom I tried in which the phone would take a hard reset - boot fine - reset and reload fine... and then whenever you tried to restart it after that it went into a boot loop that eventually came up with a screen saying "the phone cannot boot because of uncertified software or incorrect shutdown procedure"
I solved it by putting the phone into bootloader (switch on holding both power key and volume down key) - connecting it to my computer and reflashing it. It DOES NOT need a activesync connection in this mode but you do need the Hard-SPL on the phone (im running olinex 1.40)
hope that helps
Jemma

Thx JoOos and Jemmauk.
But I already tried to reflash the Radio and the rom Image.
I Tried 3 different Rom images.
One orange official , aztor re-evo and an another one.
But the phone don't display any errors. It will just never stop to reboot without saying a thing.

Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.

[Q] Please help my X1

I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.

xgenvn said:
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
Click to expand...
Click to collapse
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??

circleofomega said:
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
Click to expand...
Click to collapse
As i pay attention to the bootloader, i'm sure that it's already made the HardSPL and the phone can recognize the image on the SD Card or by USB method. The first ROM was flash on the phone is not me, this is my friend's phone, I'm just trying to help him around then.
I tried to flash the rom by USB method, but when i restarted the phone without the USB connected to PC, it did show the bootloader (i just touch the power button, not volumn button or any other key)~ then i plug USB which connect the phone to pc, soft reset it and it boot to the system again.
I try to flash it by SD-card method but it still the same. I mean that the phone can be flashed new ROM, but it's just keeping get into the bootloader everytime i restart the phone
If the image is on the SD Card it'll tell me to upgrade ROM, if the image is not on the SD Card then "No Image File!" was flashed on~
Any ideas? My friend tells me that this happened when he tried to install Sogou - chinese input application. Is there any conflicted that cause this matter?

for little detail, the phone always shows up Successfully, but it still enter the bootloader mode at next restart. Is my flash-job done or just a mistake one?

additionally, this may be bad... remove the battery doesnt work. Please help.

help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?

xgenvn said:
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
Click to expand...
Click to collapse
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.

D-jack said:
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
Click to expand...
Click to collapse
I've just tried out the task29, it's done normally, then flash the new rom.
1. I dont think the rom are buggy, because i changed between 2 roms and it's the same matter.
2. I dont need to use bootloader/rom update combo button because it's directly entered whenever i turn on the phone (without connected to pc) (i really really dont know why)
3. Hard reset and i have my WM work again but it's still the romupdate at boot time.
I wonder if jumpSPL did all this problems, I tried mtty by task 0 and set 14 0 but it wont restart the phone, tried to format the ROM by mtty (task 32) but it wont weep out, errors given: bad... at address...
Why does it always want me to update the ROM? Is there anything wrong with jumpSPL?

the problem still, please help me give a look to this.

ouch, last time I use mttty were ancient wm2003 era. i'll try to look for info, but can't promised anything.
at this point it's recommended to reflash the complete original stock rom, undo hardspl.
check the hardspl thread about restoring to factory default. best luck to you.

[Q] HD7 boot problem (not half-bricked)

Hi,
Today I found a problem with my phone. Firstly it hang and then after reset after a start screen it enters the data transfer/recovery mode witch looks like that
telephone -> usb cable -> laptop.
I cannot enter boot loader and also hard reset is not working.
Does anyone has any idea how to fix it?
Additional information:
week ago I have installed Deepshinging mango 7.5 with HSPL.
After connecting with zune it enters recovery mode, and if I try to proceed the arrow on the phone screen above changes direction to the opposite and it is crossed. After that there is an automatic reset of phone (it enters the same data transfer/recovery mode) and zune writes error 801812E0.

Try removing the USB cord and battery, then waiting a while (like 30 seconds). Put the batty back in, cross your fingers, and power on the phone.
My phone (retail ROM, OSPL) got stuck on that screen after I used the backup-at-any-time tool. Normal reboots just kept going back to that screen. The steps above fixed it. Hope that helps!

Nope, I have tried to:
- remove battery
- completely discharge battery
and still the same.

Hello,
If your phone is in mango you have to downgrade to nodo using the gold card.
Cheers.

[Q] Help: Galaxy Mini/Pop won't boot.

I haven't rooted my phone whatsoever or installed a rom or something. One day, it just won't boot. I don't use it all the time, so the battery died. I charged it so I could use it and download an app. When I try to power it on, it will only reach the flashing Samsung logo with the black background and won't go any further so I result to opening the back cover the remove the battery and try turning it on again. Still won't boot. I tried draining the battery, but it still won't boot. Would booting it without the SD card solve this problem? I heard that if I did that, I would have to factory reset it using the hardware keys. I don't want to erase everything in the phone since I'm not able to back it up. Please help. Thanks!

ZAYNlienware said:
I haven't rooted my phone whatsoever or installed a rom or something. One day, it just won't boot. I don't use it all the time, so the battery died. I charged it so I could use it and download an app. When I try to power it on, it will only reach the flashing Samsung logo with the black background and won't go any further so I result to opening the back cover the remove the battery and try turning it on again. Still won't boot. I tried draining the battery, but it still won't boot. Would booting it without the SD card solve this problem? I heard that if I did that, I would have to factory reset it using the hardware keys. I don't want to erase everything in the phone since I'm not able to back it up. Please help. Thanks!
Click to expand...
Click to collapse
You can try to boot it without SD card, but i don't think that's the problem.
I think your only possible solution is to try doing a factory reset. Try to press HOME button and POWER button together until you get to the recovery. Than, depending on the recovery you have, search for a "wipe cache/data" or "data reset".
Another solution might be using Odin, but that's the last one...

frazar said:
You can try to boot it without SD card, but i don't think that's the problem.
I think your only possible solution is to try doing a factory reset. Try to press HOME button and POWER button together until you get to the recovery. Than, depending on the recovery you have, search for a "wipe cache/data" or "data reset".
Another solution might be using Odin, but that's the last one...
Click to expand...
Click to collapse
It did work. I thought of doing that but I waited for my friend so I could consult for another way, but I resorted to a hard reset. Thanks!

sorry for you, you can't get your data back
but to solve this
you can try to wipe everything through recovery mode
(while turn of, home button + power)
if you still can't access recovery mode or still the same after wiping
you must flash your mini
[TUT]Official Gingerbread 2.3.6 09.02.2012 GalaxyMini s5570~ODIN~UPDATED
for later, backup your data app by using Titanium Backup
must root