Database Develop

Bricked Qtek 9100??

I tried to flash my Qtek 9100 to WM6 using the flashing tutorial on this site.
I followed the steps in the tutorial. I downgraded to Buttons ROM, unlocked the CID, and then I flashed the 3.08 IPL/SPL in stead of the T-Mobile 2.26.
Then I tried to use farias kitchen to make a WM6 and flashed it to the phone.
Everything seemed to go smoothly, but when I tried to start the phone after flashing the 3.08 and farias' to the phone, the phone just hangs at the startup screen with the picture of the beer glass and the coloseum.
I've tried to downgrade to Buttons firmware and I've also tried the Xda_MiniS_LaunchROM, but it doesn't help. I'm still stuck at the welcome screen.
Is there anything I can do, or have I bricked my phone for good?

flash an original qtek rom to your phone then try to flash the rom again
Your phone isnt bricked (yet)

I've done that, but it doesn't help. Still just hangs at the SPL/IPL screen.

Solution (worked for me)
I found a solution while looking trough the forum
I was facing the same problem on a G3 phone
this is copied from that link except the link to MTTY.exe is different (previous one doesn't work
See (http://forum.xda-developers.com/showthread.php?t=307332)
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY.exe ( http://forum.xda-developers.com/showthread.php?t=231190 ). After open, on Port selection, choose USB and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
I hope this helps you out
It worked for me (and other people if you look at the forums)

That solution was already known and was, in fact, discovered for the Wizard by a guy called 'Drugstore'
But what really matters is that this procedure only works if the device is already CID unlocked.
cheers

MDA Vario freezes at 2nd boot screen
I have the same problem. I flashed wm6.1 according to tutorial on this side. everything worked fine, until the time I uninstalled some application. after that my Vario froze. after soft reset it stopped on second screen (the one with info), and so it is anytime I try to reflash to other ROM. everything works fine until the time it shoud reboot.
I found this thread and tried the thing with backup image. everything worked, copying image to the phone ended with success. so I turned off the phone and started it again. but now, after all, I'm just back at the beginning
can somebody help me out with another solution??? pls.....

Try mtty
grinmustaine said:
I have the same problem. I flashed wm6.1 according to tutorial on this side. everything worked fine, until the time I uninstalled some application. after that my Vario froze. after soft reset it stopped on second screen (the one with info), and so it is anytime I try to reflash to other ROM. everything works fine until the time it shoud reboot.
I found this thread and tried the thing with backup image. everything worked, copying image to the phone ended with success. so I turned off the phone and started it again. but now, after all, I'm just back at the beginning
can somebody help me out with another solution??? pls.....
Click to expand...
Click to collapse
maybe trying mtty
task 28
task 28 55aa
then upgrade again
this is not the steps as is... so search the way

+ Que PPC said:
maybe trying mtty
task 28
task 28 55aa
then upgrade again
this is not the steps as is... so search the way
Click to expand...
Click to collapse
I didn't have chance to try this.... My Vario is already dead... Probably is my fault... As far, I wasn't able to flash to official T-mobile ROM, I did a backup copy to a SD card on my friends phone, and then tried to copy the image into mine... I'm afraid I destoyed bootloader this way After I turned off my phone first time after flashing, it didn't start again.... It doesn't react even to wall charger... Nothing... Just dead Vario

Get a powerfull charger
grinmustaine said:
I didn't have chance to try this.... My Vario is already dead... Probably is my fault... As far, I wasn't able to flash to official T-mobile ROM, I did a backup copy to a SD card on my friends phone, and then tried to copy the image into mine... I'm afraid I destoyed bootloader this way After I turned off my phone first time after flashing, it didn't start again.... It doesn't react even to wall charger... Nothing... Just dead Vario
Click to expand...
Click to collapse
There is a post that suggest that somebody revives his batt with a wall charger, maybe is your batt... is dead... or your s is bricked.

Htc s730 trouble with password

hello couple weeks ago i found htc s730 in Norway but the phone have password
when i turn it on it says :
Password
denne enheten er last. Skviv inn enhetspassordet, og klikker du meny> Avbryt fot du slar nummeret.
My question is : is it possible to "unlock it" or mayby i have to install new ROM?
thanks for all your help

You found the phone just laying around? The owner who lost the phone probably locked it.
I would do a hard reset of it to wipe the data and start over. If theres any information you can see or use on it to return it to the person missing it that would be good. Otherwise hard reset and enjoy.

yes i found it on sidewalk with empty battery and without any simcard
ok. but i have no idea how to do this.
can somebody tell me how to do the hard reset s730 ?
thanx 4 all ya comments
...
Everything works fine
restart to the factory settings hepls awesome.
thank U once again

Cant do hard reset ..
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..

The sequence of pushing and holding down is key to success:
1.) switch off
2.) push and hold l+r softkey
3.) switch on (no long push, just normal - but keep L+R pushed)
4.) wait for the prompt for reset
5.) release keys
6.) follow instructions on screen (could be "press 0 to ...")

QHelmer said:
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..
Click to expand...
Click to collapse
HTC Wings S730 Soft reset
Restarting your Phone
Restart your phone when a program is not performing properly or the phone is not responding to any keypresses.
To restart the phone
1.Remove the battery.
2.Wait for three seconds, then reinsert the battery and turn on your phone.
WARNING! If the phone is restarted while a program is running, unsaved work will be lost.
HTC Wings S730 Hard reset
Press and hold both soft buttons + press POWER button for 1 sec.
Resetting your Phone
Resetting your phone will remove all the data from its memory and restore the phone back to the factory default settings.
Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, performing a hard reset, or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
WARNING! All your data will be deleted, it is recommended that you back up your data first before resetting your phone.
To reset your phone
1.Click Start > Expert > Clear Storage.
2.Follow the on-screen instructions to reset the phone. The phone will restart after it has been reset.

thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..

Then the softkeys seem not to work ok. They are used very often and usually are the first to quit their duty. They will not work in the applications later as well, so possibly this is the reason why it was lost.
Another idea (not sure if THAT works): slide out the qwerty-keyboard and use these softkeys for the excercise, maybe that works?
A definite way to come to a hard reset is to put a new ROM on the phone. It will however only work if the phone is either CID unlocked (permanently with SuperCID or temporarily with GoldCard) or you have the original CID matching ROM update at hand.
Go to http://www.shipped-roms.com/index.php?category=windows mobile&model=Wings and pick one that fits.
Then perform a normal upgrade. If that is not possible due to the locked phone, put it in bootloader mode first:
- push and hold camera key
- switch on or insert USB cable
-> you should see 3 colour screen
From there you can start the ROM Update.

QHelmer said:
thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..
Click to expand...
Click to collapse
I think you need upgrade SPL to HardSPL...
This look at the Threads of Jockyw2001 :
Wings SSPL and HardSPL
--------------------------------------------------------------------------------
The attached SSPL and HardSPL are based on the Wings MFG SPL v0.91
- download the attached files
- REMOVE SIM and SD CARDS !!
- connect usb cable
- create a SPL backup by running spl-backup.bat from SPL-backup-kit (make sure you Wings is "application unlocked", run the attached SDA_ApplicationUnlock on PC)
- copy sspl-0.91-wings.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you only want to test the sspl try flashing the attached splash screen by running CustomRUU.exe from flash-splash-wings
- you can now flash the hardspl-0.91-wings.nbh by running CustomRUU.exe from flash-hardspl-wings
- after installing the uspl or hardspl you can flash any rom, cooked rom, radio or splash screen
Note:
The HardSPL is never overwritten which in case of flashing trouble is a great insurance. Should you want to flash another SPL or USPL you must run the SSPL.
Features:
SuperCID / Security Level=0
Does not check NBH signatures
Based on 0.91 MFG bootloader, rtask, fat2sd, sd2fat enabled
Accept any password
Model ID check only 4 chars
SPL overwrite DISABLED (to bypass, use sspl-0.91-wings.exe)
Bypasses "Task 2A" (this formats entire flash which renders your Wings into a brick, we don't want that)
Important:
Use at your own risk! I'm not responsible for any damage to your device caused by using the attached files​

Hi Hakim Raman,
...the suggested procedure will not work as you must have access to the device first for application unlock and executing applications. This is only an optional procedure if the poor guy wants to play with custom ROMs later. One step after the other...

Please help me maybe bricked...

Hy guys, after some month with my diamond and (hundred of rom changed), yesterday my phone started to reset every few seconds without possibility to start windows ...
it's seems that or soft rest button is dmaged or something with battery fault. I've tried two different battery but no way.
I've tried to flash a standard rom but after upgrade there's error an no way to finish process.
Now it' s difficult also have a soft reset because when i push red button nothing happens. Sometimes without battery i'm able to go in a boot mode...but whe i put my battery phone restart as before....
So i'm desperate......
Any suggestion???
regards

You could try to format your device and then freshly flash a new ROM:
http://forum.xda-developers.com/showpost.php?p=3433851&postcount=22

AAAARRRRRg my diamond is definitly briked.. I've tried everything to solve my problem but no way. It seems that i've a power button, so every time i put battery and start phone, after a couple of seconds i've reset in loop....
No way to take in boot mode....
There's a way to recover my data in "internal storage"??
Regards

[BUG]Infinite Reboot

Hello.
I'm opening this thread because my Diamond seems to be diying and I wanted to know if someone got an idea.
Yesterday, my phone suddendly rebooted without warning after a month.
I thought It was nothing, but the phone started to reboot allthe time. The phone boot, show my operator logo (befor the winmo loading screen), and then reboot again, again and again.
I decided to do a little Mtty maintenance and reflash (from internal memory). The phone reworked for a couple of hours and restarted to do a reboot loop. I thought the rom I was using was in fault.
Re Mtty maintenant and flashing the phone with mu Prange stock rom. Several hours léter, the phone restarted to boot.
So where I am ?
If I let the phone off (like a night), he will launch windows and will works between a couple of minutes from a couple of hours befoor rebooting. If I put the phone in bootloader mode It won't reboot and will wait with his beautiful rainbow screen. But if I leav the bootloader mode, reboot over reboot, yay !
When the phonedecide to boot completly,it's a regular soft reset, not a hard reset.
Did anyone here have an idea ? Thanks !

How often did you flash since you have your diamond ?
Try to reflash a radio. Maybe your flash memory is dead =/

It sounds like the rom image might be corrupted - I had this problem with a 28003 rom I tried in which the phone would take a hard reset - boot fine - reset and reload fine... and then whenever you tried to restart it after that it went into a boot loop that eventually came up with a screen saying "the phone cannot boot because of uncertified software or incorrect shutdown procedure"
I solved it by putting the phone into bootloader (switch on holding both power key and volume down key) - connecting it to my computer and reflashing it. It DOES NOT need a activesync connection in this mode but you do need the Hard-SPL on the phone (im running olinex 1.40)
hope that helps
Jemma

Thx JoOos and Jemmauk.
But I already tried to reflash the Radio and the rom Image.
I Tried 3 different Rom images.
One orange official , aztor re-evo and an another one.
But the phone don't display any errors. It will just never stop to reboot without saying a thing.

Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.

Butterfly S run to home screen then reboot - unrooted

Hi Guys, I come to the point where I need help please, I have very long experience in rooting but this issue I could't fix and/or find a solution for it since the 901S is unrooted there is no EXE RUU not been touched. This is my wife phone and I had same issue with main a year ago but since my phone was rooted I could fix it.
The issue is when the phone start rebooting by it self at once, nothing was done to cause that like installation app or what so ever. It start and when reach home screen, few sec it reboot from 0.
phone data: S-On, Hboot-1.61.0000, Radio 4t.31.3218.26, oS-5.16.709.4
I have tried this:
-Unlocking with unlock_code.bin, is give me the yes/no screen when I click yes it reboot to stock recovery then nothing, (it show the message about missing E bitmap)
-uploading rom stock or any other didn't work, not by using fastboot or any other method I know.
-run into save mode help give few more secs but nothing, it reboot here too
-factory reset from device didn't work as I click okay but it keep resetting.
-order *#*#3424#*#* and factory reset also nothing.
-the device memory is 95% full, I tried to format data or system or from fastboot or by deleting files also nothing get deleted all stock and after restart I see ever thing like it was.
any suggestion here?
thx all,

Any help any one

No one no help!!