Database Develop

Help please... upgrade problem.... WM5

I had a problem with my upgrade... now i whant to do a downgrade.....or even try to reinstall but i can´t......
When i prepare to downgrade...... i press power+record+reset and apears SERIAL V2.06 .I put the qtek in the cradle but the "usb" is not there in the screen....... i try to downgrade or even reinstall wm5 but he cant comunicate.... the problem isn´t in the cradle because i boot to wm5 and he comunicates...
i think that some file in the rom is missing... in bootloader he dont comunicate by usb...
"6. Put your device into bootloader mode.
Press Power + record (above the volume slider) + softreset at the same time.
You should see a white screen with "Serial" text on it and the Bootloader version.
Put your device into the cradle
Make sure that the charger of your PDA is connected to the cradle.
The text should change to "USB" now. "------------------->>> this is not shown.....only Serial Apears....
Help please............... does any one knows how I could solve this?
is there any other way to install a rom? if i try to upgrade him on wm5 desktop I get this message: "Error 100:Model ID error" , if i try to downgrade in wm5 desktop i get this message

have you opened task manager and closed the following processes?
rapimgr.exe, outlook.exe, winword.exe, wcescomm.exe, wcesmgr.exe
if you still have problems read this http://wiki.xda-developers.com/index.php?pagename=BA_5.1.1700_build_14343_Upgrade

mrcopyright said:
have you opened task manager and closed the following processes?
rapimgr.exe, outlook.exe, winword.exe, wcescomm.exe, wcesmgr.exe
if you still have problems read this http://wiki.xda-developers.com/index.php?pagename=BA_5.1.1700_build_14343_Upgrade
Click to expand...
Click to collapse
Yes, i´ve closed all the processes....... i don´t see a solution........

Dead MDAIII ... help needed

I tried to upgrade to 1.42 ...19 and my device goes dead ... after 6 hours of nervous waiting I put it from cradle and now it shows only red light when in craddle ...
i dont want to panic...but HEEEEELLLPPP :!: :!: :!: :roll: :wink:

There was something similar in the forums, but i do not remember the solution, so i will give you some things to perform.
do a hard reset (power button + reset) if it reboots, there is no problem, put it in bootloader mode (power button+reset+camera) and try to flash new rom again. if this does not work try this:
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
and if this not work you should send it to service center

Problem is I cannot turn it even into the bootloader mode.

hmmm .... first step good ... I turned it into the bootloader

and now it starts upgrading ROM .... hold breath please ... for cca 20 minutes :lol: :lol: :lol: :lol:

Time to celebrate .... Victory of spirit over the technology ... Now I have to cook my extrom and I will be happy

I am glad it worked

thnk u very much :wink:

Sep, you said at first you couldn't get your BA into bootloader mode.. what did you do to finally make it work?

well it will sound silly but I just tried things from xplodes list .... I put it into cradle and I run that app.... I tried to open port 6 and give the set 14 0 command ... it looks like it hangs but after moment the device turns into bootloader :idea: .... after this I just run instalation of the ROM again ...

I have the same problem
i have the same problem with my qtek 9100... but there is a problem, i have USB instead of the serial cable...
I do i do it? PLEASE HELP ME!!

Re: I have the same problem
xuxanga said:
i have the same problem with my qtek 9100... but there is a problem, i have USB instead of the serial cable...
I do i do it? PLEASE HELP ME!!
Click to expand...
Click to collapse
I used USB too ...

...
but i runned mtty and there is no WCEUSB... not even USB...
But i dowloaded a lower version, and the only thing that shows is USB.
Another thing is that doesn't show the other thing u say to insert 14...
I'm goi'n crazy... i'm really getting desperate!

Re: ...
xuxanga said:
but i runned mtty and there is no WCEUSB... not even USB...
But i dowloaded a lower version, and the only thing that shows is USB.
Another thing is that doesn't show the other thing u say to insert 14...
I'm goi'n crazy... i'm really getting desperate!
Click to expand...
Click to collapse
try to just open ports ...forget usb

...
none of them work...
DAMN!!
my splashscreen appears, but it stays there... saying the versions and stuff. then stays there forever...
i just bought it last week... i'm really bad luck!

...
when i open the program it shows a window of "open port setting"
Then it shows port... baud... data bits... stop bits... parity... flow control... and local echo...
I don't have to change nothing?
Only the port?
sorry to bother u...
its just for this.. i won't bother u anymore! i mean it!!
do u have messenger?

i changed ports until i found one working .... Maybe I was pure lucky ... there was nothing sophisticated in my tring :roll:

The bootloader in Wizard is difrend, I don't know if this method will work for Wizard, maybe not

mtty

Has anyone connected mtty to Diamond - if so a little help wouldn't go a miss

yes I do it daily
what exactly do you need or want to do?

LOL just sent you a PM before I read this
pof said:
yes I do it daily
what exactly do you need or want to do?
Click to expand...
Click to collapse
I used it a couple of times before on my Trinity - I am just doing research and a bit of self tuition
I am in Bootloader and no COM ports will connect to mtty.
Noobie I know but a little help would be great on getting the thing to connect - and yes have searched far and wide but to no avail.
Cheers

On Win XP:
- Activesync USB connection should be disabled (grey icon)
- Obviously, device must be in tri-colored bootloader mode (keep pressed volume down button + softreset with stylus)
- Should work with any mtty version.
On Vista (I haven't tried this myself, i don't have vista):
- Windows Mobile Device Center USB connections should be disabled
- Device must be in tri-colored bootloader mode (see above)
- If you have not installed the older XP usb drivers, you need the vista version of mtty
On Linux:
I yet don't know why the /dev/ttyUSB* device is not created for HTC Diamond, if anyone knows how to connect to Diamond's bootloader on linux let me know!

Thanks - had a version of MTTY with no USB option duh... Now lets start gathering some commands -

I just tried to use mtty but after I press enter, the application hang and then I've got the message Write Operation Failed.
Is there any settings that must be done in mtty ?
I use the vista version.

someone have an idea ?

[email protected] said:
I just tried to use mtty but after I press enter, the application hang and then I've got the message Write Operation Failed.
Is there any settings that must be done in mtty ?
I use the vista version.
Click to expand...
Click to collapse
same problem,need help plz

help please stuck on tri color screen

hi this morning i i tried to upgrade the rom on my diamond however it is now not booting past the tri color screen and it wont connect to my pc i am a newbie so prob put the wrong rom on (idiot i know) anyway the top section of screen is red and in top right corner it says ruunbh below that i have diam100 64m
spl-1.93.olinex
microp-diam (led) v11
green section psoc-diam stage_pvt v0x32
upgrade rom code error please try again
blue section nothing
white section
serial
i can not change the serial to usb and therefor cannot connect to wmdc it just same unrecognized usd device ive tried hard reset but still the same can any one help me please or should i just chuck it in bin thanks

not an expert but few things that could be made out from your comments :
-it could be a bad flash of ROM.
try this maybe it could be of some help - while on this screen, put the usb cable back on the phone and it will change from Serial to USB. try flashing the same ROM or maybe download another one and see if it works.
Best of Luck!

thanks i tried this all ready but the serial just stays there it wont change to usb

hi,
try this
download mtty on ur pc, connect ur mobile with ur pc via usb and uncheck the option of active sync. After doing this type commands in mtty (do not copypaste) :
password BsaD5SeoA (press enter & wait for sometime)
ruurun 0 (press enter)
please dont type (press enter & wait for sometime), you have to press enter button after typing BsaD5SeoA and again after typing ruurun 0
then restart and it should boot then.

hi i cannot access the phone to uncheck active sync which com port do i use on mtty each time i connect the phone to pc it comes up the usb device has malfunctioned and is unrecongnised thanks

if you cant acheive a usb connection during bootloader, then ur fone is bricked mate.... contact htc and ask about a repair

tonyplym said:
hi i cannot access the phone to uncheck active sync which com port do i use on mtty each time i connect the phone to pc it comes up the usb device has malfunctioned and is unrecongnised thanks
Click to expand...
Click to collapse
You dont need to connect to active sync as it wont even connect as ur phone is not able to start completely. You just open the active sync software and in connections just uncheck the option of sync . For COM just try all the availible COMS.
Best of luck

thanks i have just taken it out from the drawer and switched it on and serial has changed to usb so i have now reinstalled the orignal rom and im back in business thanks for all of your help now to find a suitable rom what do you recomend thanks

Need assistance please

Hi,
I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
I am trying to flash another Rom via ActiveSync, so I have connected my phone to my PC, than run the CustomRuu.exe like always, but I am stuck at 0%.
I decided to flash using the SDCard and renamed the ruu_signed.nbh to RHODIMG.nbh and than I´ve enter in the BootLoader Mode, the device tries to load the Rom, but I´ve got a white screen saying "loading..." and stays like this forever.
I cannot even HardSPL the device. I run the Rhodium-HardSPL_V2_00R3.exe but i can not get the device properly synced.
I though I had an internal memory problem so I´ve formated it using a new tool found here: http://forum.xda-developers.com/show...12&postcount=1.
But now I´ve lost everything and I can not flash any Rom with activesync, always the same problem, stuck at 0% and then the message - "Error [276] : update error.", and if I flash from SDcard a white screen saying "loading..." and stays like this forever.
EDIT:
Can not HardSPL automatic flash, because could not get the device properly synced.
Can not HardSPL with Manual flash, stuck at 0% and then the message - "Error [276] : update error.#
Any help please.
Thanks

I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
Click to expand...
Click to collapse
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?

Lennyz1988 said:
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?
Click to expand...
Click to collapse
Thanks for your reply,
Yes , you are right I have already HardSPL installed - SPL-0.85.0linex.
I have tried several Roms even the Rhodium stock Rom. If I flash via activesync I get stuck at 0% and if I flash from the SDCard (RHODIMG.nbh) I get a white screen saying "loading...." with no action.
This is strange as I´ve flash so many roms so far

Have you reset both your device and computer before connecting?

Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).

jaxboater said:
Have you reset both your device and computer before connecting?
Click to expand...
Click to collapse
rgb-rgb said:
Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).
Click to expand...
Click to collapse
I did both things with no luck.
I have put the device in bootloader mode connected to the computer then I´ve run the customRUU.exe but I am always stuck at 0%
This is the info I have in the tricolor screen:
RHOD100 32M SS-BC
SPL-0.85.0linex
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
501,529 794,848
797,208 217,213
210,853 Calibrated
I will put the device in the AC power all night to see if this is a battery issue.
Thanks

have you used a different usb cable just a suggestion

jaredcg said:
have you used a different usb cable just a suggestion
Click to expand...
Click to collapse
I had the same thought and I have used a different cable but the results are the same.

just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port

JEANRIVERA said:
just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port
Click to expand...
Click to collapse
I would try this first as posted by jeanrivera.
Also maybe you're customruu is somehow broken? Try downloading a new one. Also I don't know if it helps but when you flash via customruu do you have the image named ruu_signed.nbh? I don't know if it matters what kind of name it has, but it's just a thought