Database Develop

Serial V2.05 after an upgrade failure, can't reset, can't get out of the boot loader

HI,
because pluging in the usb cable into my laptop caused it to shut down I tried to perform an upgrade (BA_TMUK_14200_112_11300_Ship.exe) of my tmobile mda III over bluetooth.
The device was connected and after the first screen of the upgrade process the computer lost connection with the device and since then all I see on screen of my mda is Serial v2.05.
I got a powered usb hub and connected the device thorugh it to my computer, but windows doesn't recognise it anymore as a pda, but just as an unknown usb device.
I tried hard reset of the mda (camera+power+reset) and I tried to exit boot loader mode (rec+power+reset) but nothing happens.
Please help me, I am desperate.
Thnx

what the hell have u done?
upgrading via Bluetooth? have u read the wiki before upgrading? ofcourse upgrading via bluetooth will not work. ull definitely lost connection even suspending the device how much more if the device is in bootloader mode? how sad.... try it again and this time use maupgradeutnoid.exe..turn your device into bootloader mode, kill activesync..put ur device in the cradle wait till the pc recognizes the device..(something like your device is now ready for use) and then click maupgradeutnoid.exe..remember just wait till the pc recognizes your device, don't click the maupgradeutnoid.exe immediately after putting the device in the cradle cause that will not work..this time read the wiki page mate..

next option
With the MaUpgradeUt_noID.exe I get error 150:romupgrade utility error
and with the BaUpgradeUt.exe I get error 100:connection error
(I read the wiki now
What else can I do?
If I connect my blueangel directly to my laptop, the laptop shuts down, so I have to use a hub.
What else can I try?

ok...
what can u see on the screen of ur device once u put the device to cradle..(serial to usb?) ok. remember, once u put ur device in the cradle and if u want to use maupgradenoid.exe for the first time, u have to wait at least a minute before u activate or click the maupgardenoid.exe.. another option is to use mtty.exe.. just search mtty in this site and ull fine the procedure on how to use that utility..once done, u can start upgrade ur device to ur desired rom..or try update ur device to ur shipped rom using BAUpgradeUt.exe to avoid that error100.. unless u have already upgrade ur device to different roms before.

screen
when I connect it to the usb cable it says serial

ohh..
maybe there something wrong with ur device or the cable ur using. have u tried using the usb cradle instead? putting ur device in the crdle or connect it using usb cable (bootloader mode) the Serial should be changed to USB..otherwise t u get the connection error and u can't upgrade ur device for that..

[HELP]How do i put my phone in ActiveSync Mode while on Bootloader???[HELP]

I am wanting to updrage my rom for my HTC Touch HD and there are tick boxes saying that make sure u perfom these before you update:
Battery over 50%
ActiveSync
connect phone to computer using USB
Disable the standyby on PC
after i click click next and do the steps the process gets stucked on 0% buth on phone and computer and after few minutes it says error
So i am sure that i have done all those but not to sure if my phone was in Activesync mode or not.
When the phone is turned on and connected to the computer connects using Activesync fine but when i turn the phone off and go on Bootloader mode connection is lost (as soon as i turn the device off)
so can someone please help how to activesync on bootloader mode
UPDATE:
I did HSPL and then BlackstoneRUUWrapper and now its working (its not getting stuck on 0%) and actually % is increasing
Everyone Thanks in Advance. I will tell you all when its done.

If it says USB when you connect to the pc while in bootloader mode, you're good to go

ye it says USB at the bottom of the screen but the process always stays at 0% then after a while it gives Error

wich rom do you want to instal and have you instald hspl?

ABaruwal said:
ye it says USB at the bottom of the screen but the process always stays at 0% then after a while it gives Error
Click to expand...
Click to collapse
connect ur phone directly in boot loader rather than thru active sync..
Run the USPL 2..
and then start the rom flash.
jus tick all the req fields in the RUU.(be in the bootloader) cos it makes no difference..
this is all assuming u have win XP or Vista with the req drivers.
cheers
chetan

Have you followed all of the steps in the Dummies Guide to flashing? (See link in my signature.)
The fact that you are able to connect to Activesync is fine. There is no need to be in Activesync whilst flashing and while in bootlaoder mode.

Have you read through the tutorial thread? There is a troubleshooter faq there. I did my first flash using it yesterday with no problems at all

Please read and post future queries on flashing in this tutorial/guide thread

What to do when computer doesn't recognize phone plugged?

I have a problem with the diamond and needs to change ROM/SPL and other stuff, but it won't recognize that the phone has been plugged in. I have tried 5 different USB cables and 3 different computers. I don't have HTC warranty. I've done 5+ hard-resets.
Please help.

First, what OSes? For instance: win 7 doesn't recognize the phone if it tries to connect in active sync mode.

I've always used windows xp, in the past it worked.

hi,
try to connect your htc twice : my computer does not recognize my htc at first plug but when I retry in less than 1 minute, my htc displays popup menu and I can choose USB/active sync, I click done and then my computer recognizes it. I don't know if it will work with your device but you can try that ^^

Thanks for the suggestion,
I've already tried that a lot of times, nothing doing.

ok, did you try to change the status of your usb connexion ?
I mean : settings>connections>usbtoPC> then try these 4 combinations together :
- enable faster data synchronization (try both modes on/off)
- ask me about usb connection type (try both modes on/off)

I can get into bootloader, but never know that you could flash ROM in there. Is there a guide?
Also, I have a problem with a flickering screen that some threads here suggest changing SPL version to fix. Is it possible to change SPL using bootloader?

I just downoaded WM6.5 to my phone and did a ROM flash from internal storage, but USB still has problem & flickering screen still there. I need to be able to change the HardSPL w/o connection to the computer.
Is it possible to load some of the .exe in the HardSPL package and run it on the phone?
Someone help,
Thanks

Perhaps it's simply due to your PC firewall ?? Deactivate it and try to plug your htc again...

the problem is that my the computer doesn't connect with the phone via the USB cable.

just try to disable your PC firewall before connecting your device.

sorry I cannot find CustomRUU.exe on this forum, i did find DiamondCustomRUU.exe on the wiki. However, the interface for it is the same as the RomUpdateUtility.exe, which requires activesync connection.
I did proceed anyways by entering bootloader(Voldown + softreset) and run the utility -> nothing works. Then I try the USB trigger mode (Voldown + back + softreset) and run the utility -> nothing works.
I am tempted to put the HardSPL in the internal storage and rename it DIAMING.NBH and flash it but I do not know the consequences.
Thank you for your replies,
I'd appreciate more help

Need assistance please

Hi,
I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
I am trying to flash another Rom via ActiveSync, so I have connected my phone to my PC, than run the CustomRuu.exe like always, but I am stuck at 0%.
I decided to flash using the SDCard and renamed the ruu_signed.nbh to RHODIMG.nbh and than I´ve enter in the BootLoader Mode, the device tries to load the Rom, but I´ve got a white screen saying "loading..." and stays like this forever.
I cannot even HardSPL the device. I run the Rhodium-HardSPL_V2_00R3.exe but i can not get the device properly synced.
I though I had an internal memory problem so I´ve formated it using a new tool found here: http://forum.xda-developers.com/show...12&postcount=1.
But now I´ve lost everything and I can not flash any Rom with activesync, always the same problem, stuck at 0% and then the message - "Error [276] : update error.", and if I flash from SDcard a white screen saying "loading..." and stays like this forever.
EDIT:
Can not HardSPL automatic flash, because could not get the device properly synced.
Can not HardSPL with Manual flash, stuck at 0% and then the message - "Error [276] : update error.#
Any help please.
Thanks

I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
Click to expand...
Click to collapse
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?

Lennyz1988 said:
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?
Click to expand...
Click to collapse
Thanks for your reply,
Yes , you are right I have already HardSPL installed - SPL-0.85.0linex.
I have tried several Roms even the Rhodium stock Rom. If I flash via activesync I get stuck at 0% and if I flash from the SDCard (RHODIMG.nbh) I get a white screen saying "loading...." with no action.
This is strange as I´ve flash so many roms so far

Have you reset both your device and computer before connecting?

Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).

jaxboater said:
Have you reset both your device and computer before connecting?
Click to expand...
Click to collapse
rgb-rgb said:
Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).
Click to expand...
Click to collapse
I did both things with no luck.
I have put the device in bootloader mode connected to the computer then I´ve run the customRUU.exe but I am always stuck at 0%
This is the info I have in the tricolor screen:
RHOD100 32M SS-BC
SPL-0.85.0linex
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
501,529 794,848
797,208 217,213
210,853 Calibrated
I will put the device in the AC power all night to see if this is a battery issue.
Thanks

have you used a different usb cable just a suggestion

jaredcg said:
have you used a different usb cable just a suggestion
Click to expand...
Click to collapse
I had the same thought and I have used a different cable but the results are the same.

just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port

JEANRIVERA said:
just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port
Click to expand...
Click to collapse
I would try this first as posted by jeanrivera.
Also maybe you're customruu is somehow broken? Try downloading a new one. Also I don't know if it helps but when you flash via customruu do you have the image named ruu_signed.nbh? I don't know if it matters what kind of name it has, but it's just a thought

Big Problem - Is my Kaiser dead??

Happy new year everyone!
I have a big problem with my kaiser, maybe is 2011 a bad year for me ..
Well, I flashed for the third time the modded kernel of DnbTommy (including a RADIO, SPL, etc..).
Just after the flash, my Kaiser won't boot!
Just a black screen, and green LED. (can't hard reset, flash, or anything ..)
I made searchs on XDA and more, and I heard about MTTY solution..
But when I plug in my Kaiser in the USB cradle, it recognizes an unknown "Data Interface".
And MTTY does not recognize the USB port.. I tried on a Windows 7 (x64) computer, and a Windows XP (x32) laptop, with the same results.
Thanks for your help!

Try removing the battery for roughly 30 seconds then re-install

I already did it, even changing battery, but no results

Go in flash mode (camera button and reset) and flash another nbh.

Hi L1q1d,
Unfortunately, I can't go in flash mode, bootloader mode, or anything..
My screen stays black, and I can't flash!

Is the battery charged?

Of course it is !

I really need help please, elsewhere, my Kaiser will be lost..
Thanks in advance!

Have a search for the Diagnostic drivers you might be able to connect with mtty with them?

If you mean the drivers folder named
"x64 AS Drivers Win 7 Tested & Working" ,
including 2 files : wceusbsh.sys and wceusbshx64.inf
then, it does not..

No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?

meknb said:
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
Click to expand...
Click to collapse
Okay I will try it, then! Thanks!
Do I have to install them when it asks for "Data Interface" driver?

Yes just unzip them first.

Well, I tried on a Windows XP 32 Bits laptop.
I plugged in my Kaiser with USB cable, installed MotoQ Drivers when it asked for "Data Interface" drivers,
But when I run mtty.exe, it shows me 3 more "COM" ports.. But no USB!
If I plug out my Kaiser, 3 ports less appears, then..
What could I do now?
Thanks!

I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Try setboot 0 then cego via mtty.

meknb said:
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Click to expand...
Click to collapse
When I connect the Kaiser, 3 ports appears in device manager / in MTTY :
- COM3 (cant find its name in device manager)
- COM4 : "Qualcomm Diagnostics Interface 6000"
- COM5 : "Qualcomm NMEA Device"
If I connect to COM3 or COM5, MTTY seems to be blocked..
But if I select COM4, MTTY doesn't crash, but i'm unable to type a command, because it says "Invalid command" to everything I write..
Really, thanks for ur help!!

Yes com4 is the one you need to connect mtty with but id read through the frankenkaiser and related threads,you may find more help there. Good luck

I found here the thread named "Frankenkaiser SPL Loader" :
http://forum.xda-developers.com/showthread.php?t=394584
I tried the step 4, but nothing happends.
I cannot connect to MTTY with the Kaiser, that's the real problem..
Maybe there's another way than MTTY?
Over two years of flashing, it's the first problem that I get with the Kaiser..
Thanks! I really hope to find a solution to make my kaiser alive..

One thing to check is disable Allow usb connections in windows mobile device centre.
Another thing is try different versions of mtty i use mtty_0513_Test or you can try putty does the same thing as mtty.
I'm sure you'll get your kaiser back to life again.

I had stopped rapimgr.exe, but after you told me, I unchecked the "usb connection" box in ActiveSync..
Tried with MTTY 1.42, 0.01, 0513_Test, but nothing happends..
Same with PuTTY...
I think it's a communication problem!?
I would donate you, if you find the solution..