mtty - Touch Diamond, MDA Compact IV General

Has anyone connected mtty to Diamond - if so a little help wouldn't go a miss

yes I do it daily
what exactly do you need or want to do?

LOL just sent you a PM before I read this
pof said:
yes I do it daily
what exactly do you need or want to do?
Click to expand...
Click to collapse
I used it a couple of times before on my Trinity - I am just doing research and a bit of self tuition
I am in Bootloader and no COM ports will connect to mtty.
Noobie I know but a little help would be great on getting the thing to connect - and yes have searched far and wide but to no avail.
Cheers

On Win XP:
- Activesync USB connection should be disabled (grey icon)
- Obviously, device must be in tri-colored bootloader mode (keep pressed volume down button + softreset with stylus)
- Should work with any mtty version.
On Vista (I haven't tried this myself, i don't have vista):
- Windows Mobile Device Center USB connections should be disabled
- Device must be in tri-colored bootloader mode (see above)
- If you have not installed the older XP usb drivers, you need the vista version of mtty
On Linux:
I yet don't know why the /dev/ttyUSB* device is not created for HTC Diamond, if anyone knows how to connect to Diamond's bootloader on linux let me know!

Thanks - had a version of MTTY with no USB option duh... Now lets start gathering some commands -

I just tried to use mtty but after I press enter, the application hang and then I've got the message Write Operation Failed.
Is there any settings that must be done in mtty ?
I use the vista version.

someone have an idea ?

[email protected] said:
I just tried to use mtty but after I press enter, the application hang and then I've got the message Write Operation Failed.
Is there any settings that must be done in mtty ?
I use the vista version.
Click to expand...
Click to collapse
same problem,need help plz

Related

Dead MDAIII ... help needed

I tried to upgrade to 1.42 ...19 and my device goes dead ... after 6 hours of nervous waiting I put it from cradle and now it shows only red light when in craddle ...
i dont want to panic...but HEEEEELLLPPP :!: :!: :!: :roll: :wink:
There was something similar in the forums, but i do not remember the solution, so i will give you some things to perform.
do a hard reset (power button + reset) if it reboots, there is no problem, put it in bootloader mode (power button+reset+camera) and try to flash new rom again. if this does not work try this:
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
and if this not work you should send it to service center
Problem is I cannot turn it even into the bootloader mode.
hmmm .... first step good ... I turned it into the bootloader
and now it starts upgrading ROM .... hold breath please ... for cca 20 minutes :lol: :lol: :lol: :lol:
Time to celebrate .... Victory of spirit over the technology ... Now I have to cook my extrom and I will be happy
I am glad it worked
thnk u very much :wink:
Sep, you said at first you couldn't get your BA into bootloader mode.. what did you do to finally make it work?
well it will sound silly but I just tried things from xplodes list .... I put it into cradle and I run that app.... I tried to open port 6 and give the set 14 0 command ... it looks like it hangs but after moment the device turns into bootloader :idea: .... after this I just run instalation of the ROM again ...
I have the same problem
i have the same problem with my qtek 9100... but there is a problem, i have USB instead of the serial cable...
I do i do it? PLEASE HELP ME!!
Re: I have the same problem
xuxanga said:
i have the same problem with my qtek 9100... but there is a problem, i have USB instead of the serial cable...
I do i do it? PLEASE HELP ME!!
Click to expand...
Click to collapse
I used USB too ...
...
but i runned mtty and there is no WCEUSB... not even USB...
But i dowloaded a lower version, and the only thing that shows is USB.
Another thing is that doesn't show the other thing u say to insert 14...
I'm goi'n crazy... i'm really getting desperate!
Re: ...
xuxanga said:
but i runned mtty and there is no WCEUSB... not even USB...
But i dowloaded a lower version, and the only thing that shows is USB.
Another thing is that doesn't show the other thing u say to insert 14...
I'm goi'n crazy... i'm really getting desperate!
Click to expand...
Click to collapse
try to just open ports ...forget usb
...
none of them work...
DAMN!!
my splashscreen appears, but it stays there... saying the versions and stuff. then stays there forever...
i just bought it last week... i'm really bad luck!
...
when i open the program it shows a window of "open port setting"
Then it shows port... baud... data bits... stop bits... parity... flow control... and local echo...
I don't have to change nothing?
Only the port?
sorry to bother u...
its just for this.. i won't bother u anymore! i mean it!!
do u have messenger?
i changed ports until i found one working .... Maybe I was pure lucky ... there was nothing sophisticated in my tring :roll:
The bootloader in Wizard is difrend, I don't know if this method will work for Wizard, maybe not

Upgrade problem with Explode's ROM

Dear Explode:
i have read all wiki, all guides but no luck to work.
i currently have your R1 installed.
i'm using windows vista ultimate, i can sync normally between laptop and blueangel but i cannot use the upgrade
i have downloaded the OS builder and used the default like you said but when the upgrade tool launches it cannot see the phone (tried both when i put in bootloader mode and when not in bootloader mode)
i get connection error.
when i press on upgrade tool and click next (without bootloader mode on) it can identify current ROM and radio. and when i press next it restarts phone with no progress at all in USB mode.
when i press on upgrade tool and click next (after i put device in bootloader mode) (tried before and after i click) it just gives error 150.
kindly need help.
thx
Read this Thread: http://forum.xda-developers.com/showthread.php?t=291723
I can not support vista because HTC does not support it, the upgrade tools are written to work on windows XP, but you may try to run them with XP compatiblity mode
thx guys i'll give it a try and post back the results

Need Help Please With My HTC P3600 Hardspl error (260)

Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide

What to do when computer doesn't recognize phone plugged?

I have a problem with the diamond and needs to change ROM/SPL and other stuff, but it won't recognize that the phone has been plugged in. I have tried 5 different USB cables and 3 different computers. I don't have HTC warranty. I've done 5+ hard-resets.
Please help.
First, what OSes? For instance: win 7 doesn't recognize the phone if it tries to connect in active sync mode.
I've always used windows xp, in the past it worked.
hi,
try to connect your htc twice : my computer does not recognize my htc at first plug but when I retry in less than 1 minute, my htc displays popup menu and I can choose USB/active sync, I click done and then my computer recognizes it. I don't know if it will work with your device but you can try that ^^
Thanks for the suggestion,
I've already tried that a lot of times, nothing doing.
ok, did you try to change the status of your usb connexion ?
I mean : settings>connections>usbtoPC> then try these 4 combinations together :
- enable faster data synchronization (try both modes on/off)
- ask me about usb connection type (try both modes on/off)
I can get into bootloader, but never know that you could flash ROM in there. Is there a guide?
Also, I have a problem with a flickering screen that some threads here suggest changing SPL version to fix. Is it possible to change SPL using bootloader?
I just downoaded WM6.5 to my phone and did a ROM flash from internal storage, but USB still has problem & flickering screen still there. I need to be able to change the HardSPL w/o connection to the computer.
Is it possible to load some of the .exe in the HardSPL package and run it on the phone?
Someone help,
Thanks
Perhaps it's simply due to your PC firewall ?? Deactivate it and try to plug your htc again...
the problem is that my the computer doesn't connect with the phone via the USB cable.
just try to disable your PC firewall before connecting your device.
sorry I cannot find CustomRUU.exe on this forum, i did find DiamondCustomRUU.exe on the wiki. However, the interface for it is the same as the RomUpdateUtility.exe, which requires activesync connection.
I did proceed anyways by entering bootloader(Voldown + softreset) and run the utility -> nothing works. Then I try the USB trigger mode (Voldown + back + softreset) and run the utility -> nothing works.
I am tempted to put the HardSPL in the internal storage and rename it DIAMING.NBH and flash it but I do not know the consequences.
Thank you for your replies,
I'd appreciate more help

Big Problem - Is my Kaiser dead??

Happy new year everyone!
I have a big problem with my kaiser, maybe is 2011 a bad year for me ..
Well, I flashed for the third time the modded kernel of DnbTommy (including a RADIO, SPL, etc..).
Just after the flash, my Kaiser won't boot!
Just a black screen, and green LED. (can't hard reset, flash, or anything ..)
I made searchs on XDA and more, and I heard about MTTY solution..
But when I plug in my Kaiser in the USB cradle, it recognizes an unknown "Data Interface".
And MTTY does not recognize the USB port.. I tried on a Windows 7 (x64) computer, and a Windows XP (x32) laptop, with the same results.
Thanks for your help!
Try removing the battery for roughly 30 seconds then re-install
I already did it, even changing battery, but no results
Go in flash mode (camera button and reset) and flash another nbh.
Hi L1q1d,
Unfortunately, I can't go in flash mode, bootloader mode, or anything..
My screen stays black, and I can't flash!
Is the battery charged?
Of course it is !
I really need help please, elsewhere, my Kaiser will be lost..
Thanks in advance!
Have a search for the Diagnostic drivers you might be able to connect with mtty with them?
If you mean the drivers folder named
"x64 AS Drivers Win 7 Tested & Working" ,
including 2 files : wceusbsh.sys and wceusbshx64.inf
then, it does not..
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
meknb said:
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
Click to expand...
Click to collapse
Okay I will try it, then! Thanks!
Do I have to install them when it asks for "Data Interface" driver?
Yes just unzip them first.
Well, I tried on a Windows XP 32 Bits laptop.
I plugged in my Kaiser with USB cable, installed MotoQ Drivers when it asked for "Data Interface" drivers,
But when I run mtty.exe, it shows me 3 more "COM" ports.. But no USB!
If I plug out my Kaiser, 3 ports less appears, then..
What could I do now?
Thanks!
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Try setboot 0 then cego via mtty.
meknb said:
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Click to expand...
Click to collapse
When I connect the Kaiser, 3 ports appears in device manager / in MTTY :
- COM3 (cant find its name in device manager)
- COM4 : "Qualcomm Diagnostics Interface 6000"
- COM5 : "Qualcomm NMEA Device"
If I connect to COM3 or COM5, MTTY seems to be blocked..
But if I select COM4, MTTY doesn't crash, but i'm unable to type a command, because it says "Invalid command" to everything I write..
Really, thanks for ur help!!
Yes com4 is the one you need to connect mtty with but id read through the frankenkaiser and related threads,you may find more help there. Good luck
I found here the thread named "Frankenkaiser SPL Loader" :
http://forum.xda-developers.com/showthread.php?t=394584
I tried the step 4, but nothing happends.
I cannot connect to MTTY with the Kaiser, that's the real problem..
Maybe there's another way than MTTY?
Over two years of flashing, it's the first problem that I get with the Kaiser..
Thanks! I really hope to find a solution to make my kaiser alive..
One thing to check is disable Allow usb connections in windows mobile device centre.
Another thing is try different versions of mtty i use mtty_0513_Test or you can try putty does the same thing as mtty.
I'm sure you'll get your kaiser back to life again.
I had stopped rapimgr.exe, but after you told me, I unchecked the "usb connection" box in ActiveSync..
Tried with MTTY 1.42, 0.01, 0513_Test, but nothing happends..
Same with PuTTY...
I think it's a communication problem!?
I would donate you, if you find the solution..

Categories

Resources