I try to install a Rom Dopod_WM6-CHS. When it finished, my wizard is OFF.
I try to go in Bootloader, nothing!!!
I have G4 unlocked with PDAVIET3.
What happened?
Any solution?
Is this Bricked or what?
Pls
Thnks to all.
Hi
Did you had enough battery when you began the upgrade ?...just guessing
Yes. I have 70% battery.
I try wrongly to install that ROM, who was in Chinese.
When it finished, its going off, and i cant to go on.
Are you sure it doesn't enter bootloader ? Did you tried everything. BTW, why did you tried to install the chineese rom ?
Have you tried takeing off the battery for about half and hour and then trying again bootloader ? When your device is of, and you plug it into charger, does the led lights ? And if so , what colour ... orange(normal) or red or worse ...nothing ?
Yes i Try batter off for 4-5 hour.
I try hard reset (CommManager button, VoiceComm Buton and to reset), Nothing.
I dont see that it was in Chinese. In finishing of installing Extended Rom, he gone off, and no one LED light is taking on.
I dont know what.
If no led is turning on, try this. Pull out your battery, insert your charger(with the battery out) wait for a couple of seconds, and then insert the battery.
This should start charging...
Tell me wat's hapening.
Well, the ROM being in a different language should not cause any problems, rather, the IPL/SPL included in the ROM may have killed the Wizard, which either in different in terms of being G3/G4 or it is for a different unit (eg non Wizard phone).
I know that, but from what I remember, WM6 only has OS, not IPL/SPL.
That's why I was hoping that his Wizard is not dead 4ever.
anichillus said:
I know that, but from what I remember, WM6 only has OS, not IPL/SPL.
That's why I was hoping that his Wizard is not dead 4ever.
Click to expand...
Click to collapse
If any rom you flashed included a bootloader (IPL/SPL) then you have bricked your G4. You cannot flash IPL/SPL into a G4 yet. It will work until the first reset then will be a brick forever after.
If you have warranty or insurance on it you might want to exercise one of those options and hope for the best.
I hope that you did not flash a G3 or other bootloader and your device is just being temperamental.
Good Luck.
Zzan said:
If any rom you flashed included a bootloader (IPL/SPL) then you have bricked your G4. You cannot flash IPL/SPL into a G4 yet. It will work until the first reset then will be a brick forever after.
If you have warranty or insurance on it you might want to exercise one of those options and hope for the best.
I hope that you did not flash a G3 or other bootloader and your device is just being temperamental.
Good Luck.
Click to expand...
Click to collapse
the op contacted me yesterday for help....some bastard uploaded a Chinese rom to the ftp....with it seems a cross ipl/spl....this means if you install in a g3 or g4 it will brick....the file has been deleted...
Im one of victims who uses that ROM
That ROM was in Upload/Wizard/ROMS/ and i dont know who tolerate to upload that ROM who can brick a wizards of all newbies.
I think that in a future dont be that kind of mistake!!!!
faria said:
the op contacted me yesterday for help....some bastard uploaded a Chinese rom to the ftp....with it seems a cross ipl/spl....this means if you install in a g3 or g4 it will brick....the file has been deleted...
Click to expand...
Click to collapse
Is there a schedule of when moderators (or whoever) views the upload directory of the FTP and verify/move the files to the proper spots/directories on the FTP?
I know that it was recently cleaned up, and assume it is being maintained. And if so there should be no reason (other than lack of patience) for someone to DL something from the upload directory.
In any case it's unfortunate that someone is that malicious (whether intentional or not) and caused people to ruin their devices. I would think as a good rule of thumb that before you flash any file downloaded from the upload directory look for an associated thread on the file or ask about it on the forums to see if anyone knows what it is/who the author is.
Zzan said:
Is there a schedule of when moderators (or whoever) views the upload directory of the FTP and verify/move the files to the proper spots/directories on the FTP?
I know that it was recently cleaned up, and assume it is being maintained. And if so there should be no reason (other than lack of patience) for someone to DL something from the upload directory.
In any case it's unfortunate that someone is that malicious (whether intentional or not) and caused people to ruin their devices. I would think as a good rule of thumb that before you flash any file downloaded from the upload directory look for an associated thread on the file or ask about it on the forums to see if anyone knows what it is/who the author is.
Click to expand...
Click to collapse
yes we check all we can ,but we cannot check every file and its extensions.....this a voluntary job....as i rule you should only download files that you know that are safe....and for the love of good check the files with antivirus scanner...there is several treads about this problems allredy.....at the moment there is only 2 choices ;ftp for everybody or no ftp at all.
who can check if every rom uploaded for every device is good?.....there is no way.
Related
ive installed Shogun_A_La_Carte_Cingular_WWE_2 rom in my wizzard ... and now i cant connect to active sync thru usb neither can i charge it .... its like my USB port is dead...
can ne1 tell me how to revive the usb port ...
or is dere ne other way to flash sum other rom on my wizzard ..... like i can get ne size of rom or cab file on my mem card ive got a 2gb one.
please help me here really scared
if it helps dis is all that it show s in the starting
ipl 1.05
spl 1.05
os 2.26 10.2
thanx waiting for ur replies
It's not a problem of the ROM. I did the exact same thing. It's a problem of the old bootloader with the newer ROM. I finaly got it corrected by going into bootloader mode and updating the ipl/spl to 2.xx. This corrected the problem and
the phone works great with Shogun's rom. Love it.
Here's your step by step anwser
I had installed the same software for a T Mobile MDA for a Cingular Network. The ROM disabled my sync and I was ****ting bricks because I could not update my ROM, nor make calls from my wizard.
step 1. turn off the device by holding down the power button on top of the phone.
Step 2. press the camera button (right hand side) and the power button at the same time to on the device.
Step 3. This puts the device into USB mode, which you will now plug in the USB cable. (the word "USB" will appear on the bottom of the pocket pc screen when it is configured to the computer.) Active Sync will not sync up to the pocket pc (remains grayed out on the computers title bar.)
step 4. download another ROM version. I downloaded cingular 2.26 shotgun (different version from your ROM, but made for cingular devices) FROM HERE ON, DO NOT DISCOUNT YOUR DEVICE FROM THE COMPUTER!!
step 5. Make sure the device is charged more than 50%, then click and run the ROM. Follow the update prompts; and the computer will recognize that the pocket pc is connected to the usb port, but active sync will be grayed out. Allow the software to be installed. remember, do not disconnect, because you could do serious damage to the bios bank chips and never be able to boot.
once it installs the software, you will be relieved to see the NEW ROM on the boot screen and you'll notice everything works beautiful again
YOU CAN NEVER BRICK A WIZARD, just place in it USB MODE and start over. For the intelligent people, backup your information with Active Sync if you dare to experienment with new ROMs.
GOOD LUCK MY FRIEND,
Adam
aoakes said:
YOU CAN NEVER BRICK A WIZARD, just place in it USB MODE and start over.
Click to expand...
Click to collapse
If you screw your IPL/SPL then your Wizard will be bricked....just try
Molski
molski said:
If you screw your IPL/SPL then your Wizard will be bricked....just try
Molski
Click to expand...
Click to collapse
Wouldn't it be better to release your ROMs without the IPL/SPL then? Would also save you the trouble of having separate G3 and G4 versions--please don't misunderstand me, I appreciate the work you and everyone else on this forum do with no expectation of payment, but it would seem we might all be better off ROM-upgrading without and IPL/SPL, at the very least it might save some noob like naeemwaqas who doesn't know any better...just my suggestion.
here is your answer from me... it has mostly been covered..
YES hold your camera button while powering on to put in bootloader mode
DO NOT FLASH MY ROM.. yet
YES download an official rom so that you can get the updated bootloaders
after that is complete then you can flash my rom...
I DID NOT include updated bootloaders because i didnt want for a noob with a G4 to brick their phone by flashing my rom.. my future releases will be labeled as G3 and G4.. if a noob screws it up from there then its not my fault
jorge_culv said:
Wouldn't it be better to release your ROMs without the IPL/SPL then? Would also save you the trouble of having separate G3 and G4 versions--please don't misunderstand me, I appreciate the work you and everyone else on this forum do with no expectation of payment, but it would seem we might all be better off ROM-upgrading without and IPL/SPL, at the very least it might save some noob like naeemwaqas who doesn't know any better...just my suggestion.
Click to expand...
Click to collapse
but then if their IPL/SPL are of 1.xx versions, their upgrade also won't go so well. If only people would do their research before jumping into such dangerous thing..
vseehua said:
but then if their IPL/SPL are of 1.xx versions, their upgrade also won't go so well. If only people would do their research before jumping into such dangerous thing..
Click to expand...
Click to collapse
but also your looking at this the wrong way... if the ipl/spl would have been included and if he had a G4 then he would now have a brick... however he is at a point to where he can recover from...
aoakes said:
I had installed the same software for a T Mobile MDA for a Cingular Network. The ROM disabled my sync and I was ****ting bricks because I could not update my ROM, nor make calls from my wizard.
step 1. turn off the device by holding down the power button on top of the phone.
Step 2. press the camera button (right hand side) and the power button at the same time to on the device.
Step 3. This puts the device into USB mode, which you will now plug in the USB cable. (the word "USB" will appear on the bottom of the pocket pc screen when it is configured to the computer.) Active Sync will not sync up to the pocket pc (remains grayed out on the computers title bar.)
step 4. download another ROM version. I downloaded cingular 2.26 shotgun (different version from your ROM, but made for cingular devices) FROM HERE ON, DO NOT DISCOUNT YOUR DEVICE FROM THE COMPUTER!!
step 5. Make sure the device is charged more than 50%, then click and run the ROM. Follow the update prompts; and the computer will recognize that the pocket pc is connected to the usb port, but active sync will be grayed out. Allow the software to be installed. remember, do not disconnect, because you could do serious damage to the bios bank chips and never be able to boot.
once it installs the software, you will be relieved to see the NEW ROM on the boot screen and you'll notice everything works beautiful again
YOU CAN NEVER BRICK A WIZARD, just place in it USB MODE and start over. For the intelligent people, backup your information with Active Sync if you dare to experienment with new ROMs.
GOOD LUCK MY FRIEND,
Adam
Click to expand...
Click to collapse
You sir, are an idiot! And shouting such nonsense just proves my point. Please run away... and very fast before someone actually believes your bu!!!**** and bricks their device!
You sir got lucky, you obviously don't have a G4 phone, cause I double dog dare you to try such insanity on a G4.
I've flashed more phones than the average guy and I'm STILL careful.
I'm sure that you probably meant no harm but if you noticed, none of the chef's here have stated such BS...
molski said:
If you screw your IPL/SPL then your Wizard will be bricked....just try
Molski
Click to expand...
Click to collapse
Heya molski, wanna go have a drink together and watch this loser cry in his beer after he "slips" ...
shogunmark said:
here is your answer from me... it has mostly been covered..
YES hold your camera button while powering on to put in bootloader mode
DO NOT FLASH MY ROM.. yet
YES download an official rom so that you can get the updated bootloaders
after that is complete then you can flash my rom...
I DID NOT include updated bootloaders because i didnt want for a noob with a G4 to brick their phone by flashing my rom.. my future releases will be labeled as G3 and G4.. if a noob screws it up from there then its not my fault
Click to expand...
Click to collapse
Whoa, easy there samurai! My suggestion was directed at Molski, who as far as I can tell still packages up IPL/SPL in his ROMs unlike you. Thanks for pointing this crucial difference out to those who might not know otherwise.
And again, for Molski, this is just a suggestion--there have been plenty of ROM upgrades with IPL/SPL and the vast majority go fine, just seems like as a community we might want to consider doing things (like ROMs with no IPL/SPL for example) to protect newcomers. Now sure they might deserve it every now and again, and scaring the crap out of them might induce a healthy dose of "read before you leap", but could be avoided for this one situation.
jorge_culv said:
Whoa, easy there samurai! My suggestion was directed at Molski, who as far as I can tell still packages up IPL/SPL in his ROMs unlike you. Thanks for pointing this crucial difference out to those who might not know otherwise.
And again, for Molski, this is just a suggestion--there have been plenty of ROM upgrades with IPL/SPL and the vast majority go fine, just seems like as a community we might want to consider doing things (like ROMs with no IPL/SPL for example) to protect newcomers. Now sure they might deserve it every now and again, and scaring the crap out of them might induce a healthy dose of "read before you leap", but could be avoided for this one situation.
Click to expand...
Click to collapse
which is why i dont... i may know quite a bit, but im not a master, i dont know it all (dont tell my wife) and dont include ipl/spl for that simple fact.. but can garuantee this guy will read more before experimenting again... its a good scare factor, and a good way to welcome him to the board
hehehe...this is how we learn. But in some countries you could be shot for spreading such blasphemy. Peace and love brothers.
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
That really sucks...
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
which rom did u flash it with ??? wat ver ur configs before that . ur ipl/spl version os and etc.
sometime it happens that the power button doesnt works ....
try poking the reset button wiz ur stylus ... press and hold for sumtime and c wat happens
if it starts then ... press it again and wen the screen goes blank pree the camera button and hold it ... ull get into the bootloader ... den connect da usb and flash a new rom or da old factry one ...
i use molski's rom its really stable
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
nicholas99 said:
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
Click to expand...
Click to collapse
did u try da soft reset ???
yes i did but nothing happen at all
Xda Neo
I have the same problem. IPL and SPL 2.15.00001 and tryed to downgrade but after restart it does not power on. Tried everything but no way to power on. Is somebody know how to make it work again.
Regards,
You guys tried to flash a G3 Rom on your G4 Wizard.
So your bootloader (IPL/SPL) that is 2.xx.0001 is overwritten by a G3 bootloader that is 2.xx, so in other words....your devices are bricked.
Please someone, correct me if I am wrong.
Molski
yup, I agree. Bricked hopefully someone can fine the JTag on these devices.
Wow that sucks! Full moon over Miami last night, naw that can't be it .....
Sorry but unfortunately I must follow my Grandmother's advice concerning when I don't have anything nice to say...
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
magicer said:
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Click to expand...
Click to collapse
a G4 has a .00001 on the initial splash screen.
ArtXT said:
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
Click to expand...
Click to collapse
The problem is that if your bootloader (IPL/SPL) is fuc*ed up, there is no way to get it in bootloader mode to do a flash!
Only known solution is with JTAG connector, but that solution is not a clear solution yet, but I dont know nothing about that solution (simply...because I never needed it).
Molski
Dr Puttingham said:
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
Click to expand...
Click to collapse
I knew I have a G4 and can't upgrade/downgrade with G3 roms or even change IPL/SPL, but I did that :]
Just found ROM v2.22.1 (I think), like my original Wizard's was. I was so happy that I found it, that I forgot about G3 chips existence 8)
Well, ROM was for G3 -_-
Just ran too fast and slipped. Maybe I got that speed after very often Pioneer BCT 1430 flashing. It is just immortal :]
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
nicholas99 said:
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
Click to expand...
Click to collapse
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Dr Puttingham said:
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Click to expand...
Click to collapse
...which is one of the reasons why carriers make it so hard to flash a ROM from one carrier to the device of another.
Qtek 9100 half bricked
Hi Molski
I'm new here.Just 'd like to know if you could support me on this matter.
Here we go...
I've flashed my 9100 from wwe to esn (spanish) with the ROM 1.3.7.5 or something like this.
This is the problem...I got a power failure in the middle of the flashing process.So now the device isnt able to start up it didnt install the OS properly.
Now it says:
IPL 2.24 (i managed to flash the ipl n spl)
SPL 2.24
OS 1.3.7.5
But I'm pretty sure that there's no OS watsoever because after keep trying flashing with other ROM in bootload mode.I finally managed with an Orange of 34 mb it updated the ROM,that is the IPL And SPL and with the process was running I've noticed the screen got blank and updated it properly.I was realy happy when I saw it but even though it did it properly I still got the same problem.The pda doesnt start up.When I flashed it for the first time I did it with care,followed all the instructions,that is, unlocked the CID first etc.But had the damn joy of getting a power failure in the middle of it.
I'm just wondering if one of you would be able to gimme a light on it.I've tried everything but flashing it with a G4 ROM coz I know it wont work.
Regards
Luiz Santos
Molski[/QUOTE]
Hi, After the soft reset comand, I removed the battery from my Wizard. After that the followin problem was appear: the phone is bringing up to the splash screen and STOP on this position.I have tried to download another Rom but the problem still is the same. My Phone is not CID unlock and before this, I cooked own rom like is writen here http://forum.xda-developers.com/showthread.php?t=271043 . So any idea how to wake-up my phone MDA Vario.
Ok forgive me if I'm wrong here, I don't really want to judge before I know the full story, but seems to me your brain went on strike momentarily. First rule of flashing any unofficial rom CID UNLOCK YOUR DEVICE. Anyways sorry, I just wanted to say something so it doesn't happen to you again, that said, what rom did you try to upgrade to? what rom did you try to downgrade to after that? is your device a G3 or G4?
If your device is a G3 I would recommend downgrading to this rom by xelecin
ftp://xda:[email protected]_RUU_Wizard_1081002_108_10910_ENG_US.exe
it will ask you if you want to CID unlock your device at the start so you shouldn't need to worry about forgetting this time , if you can't connect your device to activesync just go into the bootloader (hold the camera, voice dial buttons while pressing the reset button) and once it connects run the set-up.
Oh another thing before I forget..... do some searching and read up a bit, because this is a pretty common topic on this forum, best of luck and hope everything works out ok. If not, report back.
*edit* I just noticed the thread that you linked to, I actually wasn't aware that this was possible, but anyways I think it's still much safer to CID unlock your device if possible, and another thing you might try replying in that thread if it doesn't work out since they should be more knowledgeable in the matter..... and that would help keep the forums less cluttered *edit*
Thanks, for your help, Unfortunately you are totaly right for my stupid act (again). At first i tried to solve the problem alone , but whole day I roam through this forum to find solution but I can't find the same problem like my. Maybe because of my ..... brain .Anyway I am with G3. NOW I have
IPL 1.0
SPL 2.26
GSM 01.09.11
OS 1.5.4.2
This is after this procedure http://forum.xda-developers.com/showthread.php?t=263116
I tried also to download also and Molski's 2.26.10.2 AKU2.3 Rom a.k.a. 2.26.10.2 Final Edition Rom, but the problem is the same : The splash screen is running and STOP and.... nothing.
I can go to bootloader and can download new rom, but I can't start fhe phone.
Yeah I know these forums aren't the easiest in which to look for info. So you can go into the bootloader, that's good. Don't try to go to a AKU2.x rom or later, keep it under that, so no 2.26 roms at all. 105, or 108 roms should be good.
Did you try the rom from the link I provided or the one on the thread? and afterwards did it go into the phone at all? My friends MDA had a similar problem last week, caused by the same thing, though in your case I see the SPL isn't updating when you install new roms on his it was the os that wasn't updating, but as soon as I installed that rom I recommended it booted up fine, then I updated his device to molski's 2.3.
I'll check back in a few so let me know how's it going.
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
DoCtOr_X said:
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
Click to expand...
Click to collapse
Ok, but tell me how to solve this :
"qiote"
8. Open ActiveSync, Explore and copy enablerapi.cab from your PC's C:\ (remember that's where you extracted lokiwiz to...) to you device, I don't care where.
9. Pick up your PDA, File Explorer, find the enablerapi.cab and click it.
"quote"
I don't have access to the phone explorer and phone at all.
masr1979 I have tried the rom you give me, but it look like there is some things I don't understand: When I start the exe file i have choice <continue> .Whet I type <c> 2(two) time the soft tell me <no device found> and order me to continue with copy ???. After few seconds tell me that Unlocker ..... Done!, and start HTC wizard Unlocker and NOTHING !!! Stop on this position more then 15 min. and only the led for charging on the phone is active.
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
masr1979 said:
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
Click to expand...
Click to collapse
Of course I'm not sure, but I thing it was 2.21. Anyway did you think that is posible to cook my own rom in G4? I'm totally confused.
Every time when I upload new rom I have this:
http://forum.xda-developers.com/attachment.php?attachmentid=32884&stc=1&d=1168184491
IMG_2976.jpg
...and also this is my bootloader screen
http://forum.xda-developers.com/attachment.php?attachmentid=32885&stc=1&d=1168184491
IMG_2977.jpg
Dr Puttingham said:
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Click to expand...
Click to collapse
Thanks, but I try to find oficial rom but without success. And very interesting thing I found.. when I start to upload new rom the soft start to check my old rom and after that tell me that i have GE (german) language, but my old was WWE ?
Is it posible some one to give me some link to official 2.x ROM but for T-mobile german language.
Well the other day I tried finding that german rom for a while.... that search was going nowhere, I saw this thread, I don't know if you might want to check into it and maybe try it out. There's mixed results apparently but who knows
http://forum.xda-developers.com/showthread.php?t=276963
Great my wizzard is stuck
its on 98% then de blue/green bar on my phone turned red en stays that way it doesnt do anything anymore, after a while my computer says the installation is finished, (SOMETIMES i get an error that has something to do with memory on my computer. or it says usb connection got lost or something)
i can reboot my phone but its going straight in the boot menu with those collors, i can try the downgrade rom again but it keeps getting stuck at 98%
anywone some suggestions?
I tried to install the folowing: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
becose i wanted to unlock my phone (dont know if its locked or not)
I tried a few other roms but they wont install at all
I forgot some info:
ipl/spl 2.18 so i have/ (HAD) a G3
gsm 01.04.10
os 2.18.1.3
it is an orange m3000 (i have a t-mobile simcard)
im using my sim in another phone do i need the simcard in the m3000 ?
well a few minutes later:
i put my simcard in my phone, but it still hangs
i tried in now on 2 computers but both are stuck at 98%
on my second pc i get the message ERROR [302] : UPDATE ERROR
The ROM update Utility has encountered communication errors during the update process. The program will guide you stem-by-step to recover from te errors so you can continue with the update.
2 choices to click: View Document or Recovery
lol i did the Recovery it made me put out the battery and reboot the phone en replug the cables
well ill try again then... :|
did it about 8 times now, keep getting stuck at 98% notice that the bar becomes red at 98%
anywone please any suggestions? im afraid i bricked my phone
There are 24 people who look at this topic and nowone has a clue what i need to do???
kaasaanfiets said:
I tried to install the folowing: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
becose i wanted to unlock my phone (dont know if its locked or not)
I tried a few other roms but they wont install at all
I forgot some info:
ipl/spl 2.18 so i have/ (HAD) a G3
gsm 01.04.10
os 2.18.1.3
it is an orange m3000 (i have a t-mobile simcard)
im using my sim in another phone do i need the simcard in the m3000 ?
Click to expand...
Click to collapse
is a 1.04.10 radio a valid radio for a 2.xx rom?
If you are stuck, the only/best way to recover is to flash an official rom from your carrier. You can get to the bootloader so you are NOT bricked. You are just flashing roms that have a CID that doesn't match your phones. Try the button rom or the wizard love rom that the unlocking stickies mention repeatedly.
Were your IPL/SPL 2.18 before you started?
Read the Wiki, Read the stickies. For every person that says the process doesn't work there are 100 that it works flawlessly for and 99% of the time those that can't get it to work don't follow all the steps in order or just outright skipped steps or substituted with what THEY thought was better. There is a reason for each and every step in the guides. IF you follow them properly you WILL NOT have any issues.
For the situation you are in now: STOP trying to flash custom roms, you MUST get your phone back to a usable state before you go down that path again. Use your carriers latest available rom to recover your device.
Also you are lucky to get an answer at all because your question is asked in almost every single new thread and every single ROM thread. The answers are already easily found if you take the time to look yourself.
thanks man, i tried the original orange rom and it worked.
RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe
im so happy, thank you for all your helpful comments
2.18 before i flased is yes.
i wanted to copy a new rom to my device, but i thought it was cid locked.
so i followed step by step the guide from faria
http://forum.xda-developers.com/showthread.php?t=263116&highlight=stuck+at+98%
but i think the problem was that i did not have an aku2 or whatever that means.
Im sorry if im being rude, but you people do a wonderful job on those roms and step by step guide's but u forget that there are people that have no clue what aku2 means when i google is, it says a new rom from t-mobile with wm5 but it doenst say how somewone can check for themselfs if they have an aku2 rom...
Im verry sorry for those noob questions but it look like a heva the same rom that i had before i messed it all up.
so can i install a new rom from here? like one of these?
Pro Black 3[1].0.1.exe
CB-AIRAF.exe
?
kaasaanfiets said:
thanks man, i tried the original orange rom and it worked.
RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe
im so happy, thank you for all your helpful comments
2.18 before i flased is yes.
i wanted to copy a new rom to my device, but i thought it was cid locked.
so i followed step by step the guide from faria
http://forum.xda-developers.com/showthread.php?t=263116&highlight=stuck+at+98%
but i think the problem was that i did not have an aku2 or whatever that means.
Im sorry if im being rude, but you people do a wonderful job on those roms and step by step guide's but u forget that there are people that have no clue what aku2 means when i google is, it says a new rom from t-mobile with wm5 but it doenst say how somewone can check for themselfs if they have an aku2 rom...
Im verry sorry for those noob questions but it look like a heva the same rom that i had before i messed it all up.
so can i install a new rom from here? like one of these?
Pro Black 3[1].0.1.exe
CB-AIRAF.exe
?
Click to expand...
Click to collapse
You will not be able to install a CUSTOM rom until you CID unlock. I don't believe the Black 3.0 rom is available for the Wizard. It is a Hermes rom. There are several WM 6 roms available for the wizard, you should probably look in the WM6 sub-thread once you get yourself completely CID unlocked.
The tutorial tells you everything you need to know, even if you don't know anything about anything. Just read the instructions follow the links to download the roms/tools that it is talking about. If you don't understand the instructions you can post in that thread and the authors or others will help you there. Though they most likely will not respond until you show that you have read and at least have an idea of what you are trying to do, where you started where you are and where you would like to end up. If you don't understand the instructions there is always the IMEI unlockers site that will give you a utility to do it if you want to pay them for it.
Why are you trying to upgrade? Do you need to upgrade? Are you willing to void your warranty on your phone? Can you live without it if something drastic happens and you truly do brick your device, in most cases you will not be able to exchange your phone under warranty? If you haven't defined the first question or answered no to any or all of the other questions you shouldn't be rom flashing, especially not with unapproved roms that aren't supported by your carrier. You need to measure the potential gains against the risk of doing these things to determine if it is right for you. Once you get unlocked and flash a couple of roms you will see that it is easy and relatively safe as long as you read and follow the instructions they are tried and true and do work if they are followed properly.
I would suggest using this thread to unlock your device: http://forum.xda-developers.com/showthread.php?t=285435
Zzan said:
You will not be able to install a CUSTOM rom until you CID unlock. I don't believe the Black 3.0 rom is available for the Wizard. It is a Hermes rom. There are several WM 6 roms available for the wizard, you should probably look in the WM6 sub-thread once you get yourself completely CID unlocked.
The tutorial tells you everything you need to know, even if you don't know anything about anything. Just read the instructions follow the links to download the roms/tools that it is talking about. If you don't understand the instructions you can post in that thread and the authors or others will help you there. Though they most likely will not respond until you show that you have read and at least have an idea of what you are trying to do, where you started where you are and where you would like to end up. If you don't understand the instructions there is always the IMEI unlockers site that will give you a utility to do it if you want to pay them for it.
Why are you trying to upgrade? Do you need to upgrade? Are you willing to void your warranty on your phone? Can you live without it if something drastic happens and you truly do brick your device, in most cases you will not be able to exchange your phone under warranty? If you haven't defined the first question or answered no to any or all of the other questions you shouldn't be rom flashing, especially not with unapproved roms that aren't supported by your carrier. You need to measure the potential gains against the risk of doing these things to determine if it is right for you. Once you get unlocked and flash a couple of roms you will see that it is easy and relatively safe as long as you read and follow the instructions they are tried and true and do work if they are followed properly.
I would suggest using this thread to unlock your device: http://forum.xda-developers.com/showthread.php?t=285435
Click to expand...
Click to collapse
I bought my phone second hand (i dont have a receet of something) so i dont have any warranty anymore
i like my phone but i have troubles with sms the recever keeps getting old of no messages so that why a want another rom
i would be a shame if i brick it, but im willing to try
im doing the steps from your link now, ik istalling te rom at the second point but it still is stuck on 98% :|
is there another 1.5 rom? that i can try? i read someting about the love rom
kaasaanfiets said:
I bought my phone second hand (i dont have a receet of something) so i dont have any warranty anymore
i like my phone but i have troubles with sms the recever keeps getting old of no messages so that why a want another rom
i would be a shame if i brick it, but im willing to try
im doing the steps from your link now, ik istalling te rom at the second point but it still is stuck on 98% :|
is there another 1.5 rom? that i can try? i read someting about the love rom
Click to expand...
Click to collapse
The Wizard Love rom is another that people use when the Button rom doesn't work for them. I don't have a link to it but I am sure it is linked in the Upgrading or G4 sub-forums. Maybe even in the Wiki. Sorry haven't been spending much time in the Wizard forums as I only flash my wizard when something breaks, or a new feature is added -- My wife uses that phone now .
There is always the pay to unlock website but you should be able to get it unlocked with either button or the wizard love rom.
Just out of curiosity how long do leave it sitting at 98% before you determine that it is stuck? All roms "stick" at a few points during the flashing process. If you didn't wait at least 5 minutes or get an error on your PC you probably didn't wait long enough. Best advice I have on this is disable all power management/screen savers on your PC set up the flash. Once it starts leave the room and close the door for no less than 30 minutes. This way you can be sure that you didn't interrupt it. For a Wizard the flash should complete in 10 minutes or less. For the Hermes it can take a full 30 minutes depending on your flashing method an which components you are flashing. It is normal to hang for a few minutes at different points during the flash process, just because there is no transfer doesn't mean something isn't being decompressed/written on the device from what has already been transferred over.
Zzan said:
The Wizard Love rom is another that people use when the Button rom doesn't work for them. I don't have a link to it but I am sure it is linked in the Upgrading or G4 sub-forums. Maybe even in the Wiki. Sorry haven't been spending much time in the Wizard forums as I only flash my wizard when something breaks, or a new feature is added -- My wife uses that phone now .
There is always the pay to unlock website but you should be able to get it unlocked with either button or the wizard love rom.
Just out of curiosity how long do leave it sitting at 98% before you determine that it is stuck? All roms "stick" at a few points during the flashing process. If you didn't wait at least 5 minutes or get an error on your PC you probably didn't wait long enough. Best advice I have on this is disable all power management/screen savers on your PC set up the flash. Once it starts leave the room and close the door for no less than 30 minutes. This way you can be sure that you didn't interrupt it. For a Wizard the flash should complete in 10 minutes or less. For the Hermes it can take a full 30 minutes depending on your flashing method an which components you are flashing. It is normal to hang for a few minutes at different points during the flash process, just because there is no transfer doesn't mean something isn't being decompressed/written on the device from what has already been transferred over.
Click to expand...
Click to collapse
Yes well i waited the first time for like 15 minutes then my computer shut down the update programm
today i waited like 30 minutes cos i even had dinner.
Well ill try the love rom some other time cos i need my phone to work sunday becose i need tomtom
thank you for your information i appreciate it verry much
i noticed that the original rom that does work: RUU_Prodigy_2180103_21801103_OR_NL_DUT_Ship.exe that one, also flashes red and green while installing so i guess thats normal...
ok ive done a search and not come up trumps.
Im looking at buying a so called bricked wizard of ebay for either spares or as a test to try and learn somit new.
The guy has flashed a g3 rom on a g4 device and now its dead.
as there any way to get the original rom back onto the device and breath some life into it ?
Ask him if he's able to get into the bootloader. If he is, it's very possible to revive it.
If not, run away!
this is wha he said !
"unit boots into a screen that say xda power or something like that.basically a phone engineer said that it was corrupt,if you understand these devices i flashed a g4 device with a g3 rom"
bleep said:
this is wha he said !
"unit boots into a screen that say xda power or something like that.basically a phone engineer said that it was corrupt,if you understand these devices i flashed a g4 device with a g3 rom"
Click to expand...
Click to collapse
A 'bricked' device works the same way a brick does, i.e, does nothing (not even start)
Since that unit does boot into something i believe there's still a chance to make it work again, but... it's not a sure thing.
ok well when it comes i cant start looking at trying to fix it.
if it cant be fixed it will be good for spares for my currently dodgy g4.
what kind of things should i be trying when it comes then >
bleep said:
ok well when it comes i cant start looking at trying to fix it.
if it cant be fixed it will be good for spares for my currently dodgy g4.
what kind of things should i be trying when it comes then >
Click to expand...
Click to collapse
The only thing you can try is to put the phone into bootloader and try to flash another rom. Dont get your hopes up though, flashing a G3 rom to a G4 tends to make this impossible.
Good Luck
so to get in bootloader what combination of buttons is it ? and i guess i just run the carriers update program to put the standard rom back on the device or is there something else i have 2 run ?
bleep said:
so to get in bootloader what combination of buttons is it ? and i guess i just run the carriers update program to put the standard rom back on the device or is there something else i have 2 run ?
Click to expand...
Click to collapse
You could have had the answer faster and easily if consulting the wiki
The way to enter the bootloader is by keeping voice-dial button pressed while poking softly the reset hole with the stylus
ta.
then run the carriers updater proggy ?
I know i should but I just thought id ask
But be sure to flash one from the ORIGINAL provider unless you're sure the CID is unlocked!
ive got the original british o2 rom here so will use that.
just a quick question. is the wizardlov rom one that works on both g3's and 4 ?
Dunno, you must check if the nk.nbf has IPL/SPL files packed and if it has then what DOC version is it for
and how u do that ?
bleep said:
and how u do that ?
Click to expand...
Click to collapse
Open the RUU with winrar or other compacter and extract the nk.nbf
Get my tool (WST - check signature), use respective button to extract the files from nk.nbf and see what files are extracted
i have read the wizard lov rom and ther is no ipl/spl files or doc so does this mean safe for g4 ?
bleep said:
i have read the wizard lov rom and ther is no ipl/spl files or doc so does this mean safe for g4 ?
Click to expand...
Click to collapse
doc? what do you mean 'doc'?
Have you extracted chunks from nk.nbf?
there was about 5-6 files extrated when i hit the extract button. to be honest i got a little lost when using it
bleep said:
there was about 5-6 files extrated when i hit the extract button. to be honest i got a little lost when using it
Click to expand...
Click to collapse
well, this is where you can't be lost
Go back and make sure that when extracting nk.nbf with WST there are no IPL or SPL files as a result. If such then it's safe to flash to a CID UNLOCKED G4
ok will let u know
ok received phone today
charged it up and turned it on
the phone freezes after the initial splash screen where it confirms the spl and ipl.
Its def a g4 device, i can get to bootloader with no issues, hard reset works fine and ask me if i want to clear rom etc so im going to attempt the flash back with the standard 02 rom .
fingers crossed it works